MPC8315ERDB boards features PCI-E x1 and Mini PCI-E x1 ports. Let's
support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When running in PCI agent mode, the PCI_CLK_OUT signals are not used, so do
not enable them. See the MPC8349EA Reference Manual, Section 4.4.2
"Clocking in PCI Agent Mode".
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
The IO port selection for MPC8544DS board:
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
This patch changes the PCIE12 and PCIE2 logic more readable.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The IO port selection is not correct on MPC8572DS and MPC8544DS board.
This patch fixes this issue.
For MPC8572
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf
PCIE2 0x3, 0x7
PCIE3 0x7
For MPC8544
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Rename _BASE to _BUS, as it's actually a PCI bus address,
separate virtual and physical addresses into _VIRT and _PHYS,
and use each appopriately. This makes the code easier to read
and understand, and facilitates mapping changes going forward.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
On newer CPUs, 8536, 8572, and 8610, the CLKDIV field of LCRR is five bits
instead of four.
In order to avoid an ifdef, LCRR_CLKDIV is set to 0x1f on all systems. It
should be safe as the fifth bit was defined as reserved and set to 0.
Code that was using a hard coded 0x0f is changed to use LCRR_CLKDIV.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Jon Loeliger <jdl@freescale.com>
Add define used to determine if PCI1 interface is in PCI or PCIX mode.
Convert users of the old PORDEVSR_PCI constant to use MPC85xx_PORDEVSR_PCI1
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
All mpc8548-based boards should implement the suggested workaround
to CPU 2 errata. Without the workaround, its possible for the
8548's core to hang while executing a msync or mbar 0 instruction
and a snoopable transaction from an I/O master tagged to make
quick forward progress is present.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The DDR controller of 8548/8544/8568/8572/8536 processors
have the ECC data init feature, and the new DDR code is
using the feature, and we don't need the way with DMA to
init memory any more.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
address-cells defaults to 2, not 1; so in the unlikely
event that it isn't specified, this patch is required
for correct operation.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Since we've changed the memory map of the board, be nice and
add some checking to try to catch out-of-date .dts files. We do
this by checking the CCSRBAR location in the .dts and comparing
it to the CCSRBAR location in u-boot. If they don't match, a
warning msg is printed. This isn't foolproof, but it's simple and
will catch most of the cases where an out-of-date .dts is present,
including all of the cases where a new u-boot is used with an old
standard MPC8641 .dts file as supplied with Linux.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
This patch creates a memory map with all the devices
in 36-bit physical space, in addition to the 32-bit map.
The CCSR relocation is moved (again, sorry) to
allow for the physical address to be 36 bits - this
requires translation to be enabled. With 36-bit physical
addressing enabled, we are no longer running with VA=PA
translations. This means we have to distinguish between
the two in the config file. The existing region name is
used to indicate the virtual address, and a _PHYS variety
is created to represent the physical address.
Large physical addressing is not enabled by default.
Set CONFIG_PHYS_64BIT in the config file to turn this on.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
The memory map on the 8641hpcn is modified to look more like
the 85xx boards; this is a step towards a more standardized
layout going forward. As part of this change, we now relocate
the flash.
The regions for some of the mappings were far larger than they
needed to be. I have reduced the mappings to match the
actual sizes supported by the hardware.
In addition I have removed the comments at the head
of the BAT blocks in the config file, rather than updating
them. These get horribly out of date, and it's a simple
matter to look at the defines to see what they are set to
since everything is right here in the same file.
Documentation has been changed to reflect the new map, as this
change is user visible, and affects the OS which runs post-uboot.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
There's a lot of setup and foo for the second flash
bank. The problem is, this board doesn't actually have one.
Clean this up. Also, the flash is 8M in size. Get rid
of the confusing aliased overmapping, and just map 8M.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
You can't actually have both, and with some coming changes to
change the memory map for the board and support 36-bit physical,
we need the extra BAT that is being consumed by having both.
I also make non-PCI configs build cleanly, for the sake of sanity.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Fix compilation issue caused by a few mismatches.
Provide proper nand chip select enable/disable in
nand_hwcontrol() rather than in board_nand_init()
just enable once. Remove redundant local nand driver
functions - nand_read_byte(), nand_write_byte() and
nand_dev_ready() to use common nand driver.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Will use mcfmii.c driver in drivers/net rather than
keep creating new mii.c for each future platform.
Remove EB+MCF-EV123, cobra5272, idmr, M5235EVB,
M5271EVB, M5272C3, M5275EVB, M5282EVB, M5329EVB,
M5373EVB, M54451EVB, M54455EVB, M547xEVB, and M548xEVB's
mii.c
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Each different build for M54455EVB and M5235EVB will
create a u-boot.lds linker file. It is redundant to
keep the u-boot.lds
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.
Singed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DDR1 LAW will precedence the DDR2 LAW, so remove
the second DDR LAW.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
The DDR controller of 86xx processors have the ECC data init
feature, and the new DDR code is using the feature, we don't
need the way with DMA to init memory again.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Kumar Gala <kumar.gala@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
- Rename lbus83xx_t to fsl_lbus_t and move it to asm/fsl_lbc.h so that it
can be shared by both 83xx and 85xx
- Remove lbus83xx_t and replace it with fsl_lbus_t in all 83xx boards
files which use lbus83xx_t.
- Move FMR, FIR, FCR, FPAR, LTESR from mpc83xx.h to asm/fsl_lbc.h so that
85xx can share them.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Converted MPC8610HCPD, MPC8641HPCN, and SBC8641D to use
fsl_pci_setup_inbound_windows() and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Converted ATUM8548, MPC8536DS, MPC8544DS, MPC8548CDS, MPC8568MDS,
MPC8572DS, TQM85xx, and SBC8548 to use fsl_pci_setup_inbound_windows()
and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
With this patch u-boot can fixup the dr_mode and phy_type properties
for the Dual-Role USB controller.
While at it, also remove #ifdefs around includes, they are not needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The MPC837xE-MDS board's CPLD can auto-detect if the board is on the PIB,
standalone or acting as a PCI agent. User's Guide says:
- When the CPLD recognizes its location on the PIB it automatically
configures RCW to the PCI Host.
- If the CPLD fails to recognize its location then it is automatically
configured as an Agent and the PCI is configured to an external arbiter.
This sounds good. Though in the standalone setup the CPLD sets PCI_HOST
flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
any arbiter bad things will happen (here the board hangs during any config
space reads).
In this situation we must disable the PCI. And in case of anybody really
want to use an external arbiter, we provide "pci_external_aribter"
environment variable.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This involves configuring the SerDes and fixing up the flags and
PHY addresses for the TSECs.
For Linux we also fix up the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC837xE specs says that SerDes1 has:
— Two lanes running x1 SGMII at 1.25 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
And for SerDes2:
— Two lanes running x1 PCI Express at 2.5 Gbps;
— One lane running x2 PCI Express at 2.5 Gbps;
— Two lanes running x1 SATA at 1.5 or 3.0 Gbps.
The spec also explicitly states that PEX options are not valid for
the SD1.
Nevertheless MPC8378 RDB and MDS boards configure the SD1 for PEX,
which is wrong to do.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Currently 64M of LBC SDRAM are mapped at 0xF0000000 which makes
it difficult to use (b/c then the memory is discontinuous and
there is quite big memory hole between the DDR/SDRAM regions).
This patch reworks LBC SDRAM setup so that now we dynamically
place the LBC SDRAM near the DDR (or at 0x0 if there isn't any
DDR memory).
With this patch we're able to:
- Boot without external DDR memory;
- Use most "DDR + SDRAM" setups without need to support for
sparse/discontinuous memory model in the software.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
mpc8536ds.c: In function 'is_sata_supported':
mpc8536ds.c:615: warning: unused variable 'devdisr'
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The pixis sgmii command depend on the FPGA support on the board, some 85xx
boards support SGMII riser card but did not support this command, define
CONFIG_PIXIS_SGMII_CMD for those boards which support the sgmii command.
Not like 8544, 8572 has 4 eTsec so that the other two's pixis bits
are not supported by 8544. Therefor, define PIXIS_VSPEED2_MASK and
PIXIS_VCFGEN1_MASK in header file for both boards.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0.
Include host_agent == 0 decode for end-point determination.
This is not needed for the ds reference board since pcie3 will be a host
in order to connect to the uli chip. Include it here as a reference for
other mpc8572 boards.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.
* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash. Instead we can just flush the L1 d-cache and invalidate the i-cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SGMII and SATA share the serdes on MPC8536 CPU, When SATA disabled and the
driver still try to access the SATA registers, the cpu will hangup.
This patch try to fix this by reading the serdes status before the SATA
initialize.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
When aligning malloc()ed screen_base, invalid offset was added.
This not only caused misaligned result (which did not cause hardware
misbehaviour), but - worse - caused screen_base + smem_len to
be out of malloc()ed space, which in turn caused breakage of
futher malloc()/free() operation.
This patch fixes screen_base alignment.
Also this patch makes memset() that cleans framebuffer to be executed
on first initialization of diu, not only on re-initialization. It looks
correct to clean the framebuffer instead of displaying random garbage;
I believe that was disabled only because that memset caused breakage
of malloc/free described above - which no longer happens with the fix
described above.
Signed-off-by: Nikita V. Youshchenko <yoush@debian.org>
get_cpu_board_revision() returned board revision based on information stored
in global static struct eeprom. It should instead use one from local struct
board_eeprom, to which the data is actually read from EEPROM. The bug led to
system hang after printing L1 cache information on U-Boot startup. The problem
was observed on MPC8555CDS system and possibly affects other Freescale MPC85xx
boards using CFG_I2C_EEPROM_CCID.
The change has been successfully tested on MPC8555CDS system.
Signed-off-by: Rafal Czubak <rcz@semihalf.com>
The spd_dram code shifts the base address, then masks 20 bits, but
forgets to shift the base address back. Fix this by just masking the
base address correctly.
Found this bug while trying to relocate a DDR memory at the base != 0.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The new sys_eeprom.c supports both the old CCID EEPROM format and the new NXID
format, and so it obsoletes board/freescale/common/cds_eeprom.c. Freescale
86xx boards already use sys_eeprom.c, so this patch migrates the remaining
Freescale 85xx boards to use it as well. cds_eeprom.c is deleted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Affected boards:
hidden_dragon
MPC8544DS
MPC8610HPCN
R2DPLUS
TB0229
Removed initialization of the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS platforms support an optional SGMII riser card to
expose ethernet over an SGMII interface. Once the card is in, it is also
necessary to configure the board such that it uses the card, rather than
the on-board ethernet ports. This can either be done by flipping dip switches
on the motherboard, or by modifying registers in the pixis. Either way
requires a reboot.
This adds a command to allow users to choose which ports are routed through
the SGMII card, and which through the onboard ports. It also allows users
to revert to the current switch settings.
This code does not work on the 8572, as the PIXIS is different.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544 DS has an optional SGMII Riser card, which uses different PHY
addresses. Check if we are in SGMII mode, and invoke the SGMII Riser
setup code if so.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
The 8544DS and 8572DS systems have an optional SGMII riser card which
exposes new ethernet ports which are connected to the eTSECs via an
SGMII interface. The SGMII PHYs for this board are offset from the standard
PHY addresses, so this code modifies the passed in tsec_info structure to
use the SGMII PHYs on the card, instead.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add FEC pin set and mii reset in __mii_init(). Change
legacy flash vendor from 2 to AMD LEGACY (0xFFF0),
change cfi_offset to 0, and change CFG_FLASH_CFI to
CONFIG_FLASH_CFI_LEGACY. Correct M54451EVB and
M54455EVB env settings in configuration file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Dejan Minic <minic@freescale.com>
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The only board using this driver is the Freescale MPC8610HPCD board.
Removed initialization for the driver from net/eth.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
PCI I/O space is currently mapped 1:1 at 0xFA000000. Linux requires
PCI I/O space to start at 0 on the PCI bus. This patch maps PCI I/O
space such that 0xFA000000 in the processor's address space maps to 0
on the PCI I/O bus.
Signed-off-by Randy Vinson <rvinson@mvista.com>
Acked-by: Roy Zang <tie-fei.zang@freescale.com>
Add the ability for the MPC8349EMDS to run in PCI Agent mode, acting as a
PCI card rather than a host computer.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change the MPC8349EMDS board to use the generic PCI initialization code
for the mpc83xx cpu.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
There is no point in disabling the icache on 7xx/74xx/86xx parts and not
also flushing the icache. All callers of invalidate_l1_instruction_cache()
call icache_disable() right after. Make it so icache_disable() calls
invalidate_l1_instruction_cache() for us.
Also, dcache_disable() already calls dcache_flush() so there is no point
in the explicit calls of dcache_flush().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Incorrect CFG_HZ value, change 1000000 to 1000.
Rename #waring to #warning. RAMBAR1 uses twice
in start.S, rename the later to FLASHBAR. Insert
nop for DRAM setup. And, env_offset in linker file.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Remove non-common flash driver in
board/freescale/m54455evb/flash.c. The non-cfi flash will
use CONFIG_FLASH_CFI_LEGACY to configure the flash
attribute.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
