Extend the existing driver to support the SCIF serial ports on the
Renesas RZ/G2L (R9A07G044) SoC. This also requires us to ensure that if
there is a reset signal defined in the device tree, it is de-asserted
before we try to talk to the SCIF module.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Tested-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # R-Car H3 Salvator-XS
The i.MX8MP DHCOM SoM production rev.200 is populated with M24C32-D
EEPROMs which have Additional Write lockable page at separate I2C
address. Describe the page in DT to make it available.
Disable the additional page in rev.100 SoM DTO as those devices
contain EEPROM without an Additional Write lockable page.
Signed-off-by: Marek Vasut <marex@denx.de>
Import device tree changes from Linux v6.6-rc6 for Amlogic A1 board.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20231017213211.121550-3-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Make sure we have an IMX header before calling spl_load_imx_container,
since if we don't it will fail with -ENOENT. This allows us to fall back to
legacy/raw images if they are also enabled.
This is a functional change, one which likely should have been in place
from the start, but a functional change nonetheless. Previously, all
non-IMX8 images (except FITs without FIT_FULL) would be optimized out if
the only image load method enabled supported IMX8 images. With this change,
support for other image types now has an effect.
There are seven boards with SPL_LOAD_IMX_CONTAINER enabled: three with
SPL_BOOTROM_SUPPORT:
imx93_11x11_evk_ld imx93_11x11_evk imx8ulp_evk
and four with SPL_MMC:
deneb imx8qxp_mek giedi imx8qm_mek
All of these boards also have SPL_RAW_IMAGE_SUPPORT and
SPL_LEGACY_IMAGE_FORMAT enabled as well. However, none have FIT support
enabled. Of the six load methods affected by this patch, only SPL_MMC and
SPL_BOOTROM_SUPPORT are enabled with SPL_LOAD_IMX_CONTAINER.
spl_romapi_load_image_seekable does not support legacy or raw images, so
there is no growth. However, mmc_load_image_raw_sector does support loading
legacy/raw images. Since these images could not have been booted before, I
have disabled support for legacy/raw images on these four boards. This
reduces bloat from around 800 bytes to around 200.
There are no in-tree boards with SPL_LOAD_IMX_CONTAINER and AHAB_BOOT both
enabled, so we do not need to worry about potentially falling back to
legacy images in a secure boot scenario.
Future work could include merging imx_container.h with imx8image.h, since
they appear to define mostly the same structures.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
These error messages are missing newlines. Add them.
Fixes: 6e81ca220e ("imx: parse-container: Use malloc for container processing")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
We should load images to their destination, not their entry point.
Fixes: 7b86cd4274 ("imx8: support parsing i.MX8 Container file")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Implement the 'getprisec' subcommand of 'bmode' command for i.MX8M by
reading out the ROM log events. This event is set by the BootROM if it
switched to the secondary copy due to primary copy being corrupted.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
In case of a secondary image boot from the user area of an eMMC device,
the correct offset must be calculated. The offset is fused in the fuse
IMG_CNTN_SET1_OFFSET of the i.MX8M Nano and Plus. The calculation of the
offset is described in the reference manual (IMX8MNRM Rev. 2, 07/2022
and IMX8MPRM Rev. 1, 06/2021):
The fuse IMG_CNTN_SET1_OFFSET (0x490[22:19]) is defined as follows:
* Secondary boot is disabled if fuse value is bigger than 10,
n = fuse value bigger than 10.
* n == 0: Offset = 4MB
* n == 2: Offset = 1MB
* Others & n <= 10 : Offset = 1MB*2^n
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out parsing of ROM log in function spl_mmc_emmc_boot_partition().
This can be helpful to detect a secondary image boot without fiddling
around with MMC partitions. This way for example, U-Boot is able to
detect a secondary image boot and can enter some fallback scenario like
starting a recovery mode.
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce two new weak functions, arch_spl_mmc_get_uboot_raw_sector() and
board_spl_mmc_get_uboot_raw_sector(), each of which can be overridden at
a matching level, that is arch/ and board/ , in addition to the existing
weak function spl_mmc_get_uboot_raw_sector().
This way, architecture code can define a default architecture specific
implementation of arch_spl_mmc_get_uboot_raw_sector(), while the board
code can override that using board_spl_mmc_get_uboot_raw_sector() which
takes precedence over the architecture code. In some sort of unlikely
special case where code has to take precedence over board code too, the
spl_mmc_get_uboot_raw_sector() is still left out to be a weak function,
but it should be unlikely that this is ever needed to be overridden.
Signed-off-by: Marek Vasut <marex@denx.de>
i.MX93 11x11 EVK fails to boot:
U-Boot SPL 2023.10-00558-g65b9b3462bec-dirty (Oct 03 2023 - 17:40:10 +0200)
SOC: 0xa0009300
LC: 0x40010
M33 prepare ok
Normal Boot
Trying to boot from BOOTROM
Boot Stage: Primary boot
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x44400 by ROM_API
NOTICE: BL31: v2.8(release):android-13.0.0_2.0.0-0-ge4b2dbfa52f5
NOTICE: BL31: Built : 17:52:46, Sep 28 2023
That's because commit 9e644284ab ("dm: core: Report
bootph-pre-ram/sram node as pre-reloc after relocation"):
"[This] changes behavior of what nodes are bound in the U-Boot
proper pre-relocation phase. Change to bootph-all or add
bootph-some-ram prop to restore prior behavior."
Fix this by adding bootph-some-ram prop as suggested by the commit
above.
Fixes: 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.
The ARM TrustedFirmware code for the Renesas RZ/G2L SoC family passes a
devicetree blob to the bootloader as an argument in the same was
previous R-Car gen3/gen4 SoCs. This blob contains a compatible string
which can be used to identify the particular SoC we are running on and
this is used to select the appropriate device tree to load.
The configuration renesas_rzg2l_smarc_defconfig is added to support
building for this target. In the future this defconfig will be extended
to support other SoCs and evaluation boards from the RZ/G2L family.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Renesas RZ/G2L SMARC Evaluation Board Kit consists of the RZ/G2L
System-on-Module (SOM) based on the R9A07G044L2 SoC, and a common SMARC
carrier board.
This patch is based on the corresponding Linux v6.5 device tree
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The memory map for the RZ/G2L family differs from that of previous R-Car
Gen3/Gen4 SoCs.
A high level memory map can be seen in figure 5.2 (section 5.2.1) of the
RZ/G2L data sheet rev 1.30 published May 12, 2023. A summary is included
here (note that this is a 34-bit address space):
* 0x0_0000_0000 - 0x0_0002_FFFF SRAM area
* 0x0_0003_0000 - 0x0_0FFF_FFFF Reserved area
* 0x0_1000_0000 - 0x0_1FFF_FFFF I/O register area
* 0x0_2000_0000 - 0x0_2FFF_FFFF SPI Multi area
* 0x0_3000_0000 - 0x0_3FFF_FFFF Reserved area
* 0x0_4000_0000 - 0x1_3FFF_FFFF DDR area (4 GiB)
* 0x1_4000_0000 - 0x3_FFFF_FFFF Reserved area
Within the DDR area, the first 128 MiB are reserved by TrustedFirmware.
The region from 0x43F00000 to 0x47DFFFFF inclusive is protected for use
in TrustedFirmware/OP-TEE, but all other memory is included in the
memory map. This reservation is the same as used in R-Car
Gen3/Gen4 and RZ/G2{H,M,N,E} SoCs.
DRAM information is initialised based on the data in the fdt.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The ARM TrustedFirmware code for the Renesas RZ/G2L SoC family passes a
devicetree blob to the bootloader as an argument in the same was
previous R-Car Gen3/Gen4 SoCs. This blob contains a compatible string
which can be used to identify the particular SoC we are running on.
We do this as reading the DEVID & PRR registers from u-boot is not
sufficient to differentiate between the R9A07G044L (RZ/G2L) and
R9A07G044C (RZ/G2LC) SoCs. An additional read from offset 0x11861178 is
needed but this address is in the OTP region which can only be read from
the secure world (i.e. TrustedFirmware). So we have to rely on
TrustedFirmware to determine the SoC and pass this information to u-boot
via an fdt blob.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
We don't want to rely on source files including <asm/types.h> before
<asm/arch/rmobile.h>.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add USB0 OTG support.
Currently, the USB0 OTG nodes are not enabled in the Linux kernel
devicetree.
For this reason, enable the USB0 OTG nodes inside imx8mp-evk-u-boot.dtsi
for now.
Also select several useful options such as USB gadget and fastboot.
Tested by running "ums 0 mmc 2".
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The GPIO3 has to be available early during U-Boot proper start up for
DRAM size detect to work correctly. The GPIO3 is currently available in
SPL and late in U-Boot proper, which is insufficient. Add the missing
bootph-all to make the GPIO3 available also early in U-Boot proper.
Signed-off-by: Marek Vasut <marex@denx.de>
The xfi3 target has been removed by commit 539fba2c10 ("arm:
Remove xfi3 board"), but it missed to remove an entry from the
mxs Kconfig.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
SPDX-License tag is missing and checkpatch complains about it.
Add the SPDX-License tag using the same one from imx7d-sdb.dts.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes production rev.200 SoM,
add DT overlay which reinstates rev.100 SoM description to permit
prototype rev.100 SoMs to be used until they get phased out.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the i.MX8MP DHCOM rev.100 has been populated on the PDK3
carrier board, the on-SoM PHY PHYAD1 signal has been pulled high
by the carrier board and changed the PHY MDIO address from 5 to 7.
This has been fixed on production rev.200 SoM by additional buffer
on the SoM PHYAD/LED signals, remove the workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes prototype rev.100 SoM,
update the DT to describe production rev.200 SoM which brings the
following changes:
- Fast SoC GPIOs exposed on the SoM edge connector
- Slow GPIOs like component resets moved to I2C GPIO expander
- ADC upgraded from TLA2024 to ADS1015 with conversion interrupt
- EEPROM size increased from 256 B to 4 kiB
Signed-off-by: Marek Vasut <marex@denx.de>
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <marex@denx.de>
The current code works by sheer coincidence, because (see HABv4 API
documentation, section 3.4) the RVT authenticate_image call updates
the size that is passed in with the actual size ROM code pulls from
IVT/CSF . So if the input size is larger, that is "fine" . Pass in
size instead to make this really correct.
Signed-off-by: Marek Vasut <marex@denx.de>
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver adds support for the gpio features of the GPIO/PFC module in
the Renesas RZ/G2L (R9A07G044) SoC.
The new `rzg2l-pfc-gpio` driver is bound to the same device tree node as
the `rzg2l-pfc-pinctrl` driver as the same hardware block provides both
GPIO and pin multiplexing features.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver adds support for the pinctrl features of the GPIO/PFC module
in the Renesas RZ/G2L (R9A07G044) SoC.
A multi-function `rzg2l-pfc` driver is defined for UCLASS_NOP, which
binds the `rzg2l-pfc-pinctrl` UCLASS_PINCTRL driver dynamically. We also
define common macros and functions for the PFC in <renesas/rzg2l-pfc.h>.
This makes it easy to add an additional UCLASS_GPIO driver for the GPIO
functionality of this module in a follow-up patch.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/G2L family uses CONFIG_RCAR_64 but does not share a common PFC
driver with the R-Car gen3 & gen4 boards.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This driver provides clock and reset control for the Renesas R9A07G044L
(RZ/G2L) and R9A07G044C (RZ/G2LC) SoC. It consists of two parts:
* driver code which is applicable to all SoCs in the RZ/G2L family.
* static data describing the clocks and resets which are specific to the
R9A07G044{L,C} SoCs. The identifier r9a07g044 (without a final letter)
is used to indicate that both SoCs are supported.
clk_set_rate() and clk_get_rate() are implemented only for the clocks
that are actually used in u-boot.
The CPG driver is marked with DM_FLAG_PRE_RELOC to ensure that its bind
function is called before the SCIF (serial port) driver is probed. This
is required so that we can de-assert the relevant reset signal during
the serial driver probe function.
This patch is based on the corresponding Linux v6.5 driver
(commit 52e12027d50affbf60c6c9c64db8017391b0c22e).
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add a config option for the R9A07G044L SoC used in the RZ/G2L so that we
can make use of this in the subsequent driver patches.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The Renesas RZ/G2L family includes the following ARM SoCs:
* RZ/G2L (r9a07g044l)
* RZ/G2LC (r9a07g044c)
* RZ/G2UL (r9a07g043u)
* RZ/V2L (r9a07g054l)
Support for individual SoCs and evaluation boards will be added in
separate patches.
Signed-off-by: Paul Barker <paul.barker.ct@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
When CLK is enabled, get_lpuart_clk_rate() needs to get a per clock of
lpuart, so that add a per clock for lpuart1.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The USB_PWR signal operation is not reliable on this DWC3 controller
instance in case the signal is active high. Switch to GPIO control,
which always behaves correctly. Perform the change in u-boot extras
until this hits Linux upstream.
Signed-off-by: Marek Vasut <marex@denx.de>
This reverts commit 5c1c6b7306. The reason
for switching to i2c-gpio was due to an issue we were seeing in the
Linux kernel where the CPU would lock up on certain adverse I2C bus
conditions. We were never able to reproduce the lockup in U-Boot but
assumed that was probably just luck.
Since then we have discovered that the lock up was due to the I2C
transaction offload engine in the I2C controller not coping with the
adverse bus conditions (basically it thinks there's another master and
waits for a STOP condition that never comes). U-Boot doesn't use the I2C
offload feature so is not susceptible to the lockup.
We can therefore safely return to using the built-in I2C controller.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The cn9130.dtsi defines a pinctrl node for SPI1 (until recently it was
mislabeled as spi0). Use this instead of having a duplicate definition
with a different label.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The CN9130-DB uses the SPI1 interface but had the pinctrl node labelled
as "cp0_spi0_pins". Use the label "cp0_spi1_pins" and update the node
name to "cp0-spi-pins-1" to avoid confusion with the pinctrl options for
SPI0.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend the padding process of u-boot-nand.imx target by adding 10k bytes
of zeros to the end of the binary using the 'dd' command.
The existing padding method did not generate a functional binary,
as discussed in more detail in this thread [1]. Instead, we adopt the
end-padding calculation method documented in 'board/doc/colibri_imx7.rst'
as a reference, which is relevant for iMX7 with NAND storage.
Adding 10k bytes of zeros provides an approximate value that makes the
proper padding for these NAND devices.
[1] https://lore.kernel.org/all/CAC4tdFUqffQzRQFv5AGe_xtbFy1agr2SEpn_FzEdexhwjdryyw@mail.gmail.com/
Signed-off-by: Hiago De Franco <hiago.franco@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
These IS_ENABLED(CONFIG_SPL_LOAD_FIT) cases can no longer be reached,
and thus get_fit_image_size() is also redundant.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Currently, spl_imx_romapi uses a somewhat tricky workaround for the
fact that a FIT image with external data doesn't directly allow one to
know the full size of the file: It does a dummy spl_load_simple_fit(),
having the ->read callback remember the largest offset requested, and
then does a last call to rom_api_download_image() to fetch the
remaining part of the full FIT image.
We can avoid that by just keeping track of how much we have downloaded
already, and if the ->read() requests something outside the current
valid buffer, fetch up to the end of the current request.
The current method also suffers from not working when CONFIG_IMX_HAB
is enabled: While in that case u-boot.itb is not built with external
data, so the fdt header does contain the full size of the dtb
structure. However, it does not account for the extra CONFIG_CSF_SIZE
added by board_spl_fit_size_align(). And also, the data it hands out
during the first dummy spl_load_simple_fit() is of course garbage, and
wouldn't pass the verification.
So we really need to call spl_load_simple_fit() only once, let that
figure out just how big the FIT image is (including whatever data, CSF
or "ordinary" external data, has been tacked on beyond the fdt
structure), and always provide valid data from the ->read callback.
This only affects the CONFIG_SPL_LOAD_FIT case - I don't have any
hardware or experience with the CONFIG_SPL_LOAD_IMX_CONTAINER case, so
I leave that alone for now.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The hab signing script doc/imx/habv4/csf_examples/mx8m/csf.sh does
fdtget -t x u-boot.dtb /binman/imx-boot/uboot offset
to figure out the offset of u-boot.itb inside flash.bin. That works
fine for imx8mm, imx8mn, imx8mq, but fails for imx8mp because in that
case 'uboot' is merely a label and not actually the node name.
Homogenize these cases and make imx8mp the same as the other imx8m*
variants. The binman type is explicitly given and no longer derived
from the node name, and the csf.sh script will work for all four SOCs.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
If optee is detected configure it in the Linux device-tree:
- add /firmware/optee node
- add /reserved-memory nodes for optee_core and optee_shm
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Move the crypto and sec_jr* nodes from board-specific
u-boot.dtsi files into the common files. Additionally protect the
nodes with ifdef CONFIG_FSL_CAAM as they don't serve any purpose if
that is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
There is no need to include the firmware/optee node if the optee
driver is not enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the firmware/optee node to the common imx8mp-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Move the firmware/optee node to the common imx8mm-u-boot.dtsi and
protect it with an ifdef CONFIG_OPTEE as it is a meaningless node
without the optee driver enabled.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Enable USB SDP SPL aka serial downloader recovery mode support.
While at it also enable fastboot support which may be used to
subsequently load further stages like a Toradex Easy Installer FIT
image.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Update the imx8mp-venice-gw74xx for revB:
- add CAN1
- add TIS-TPM on SPI2
- add FAN controller
- fix PMIC I2C bus (revA PMIC I2C was non-functional so no need for
backward compatible option)
- M2 socket GPIO's moved
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mm-venice-gw7905-0x consists of a SOM + baseboard.
The GW700x SOM contains the following:
- i.MX8M Mini SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- RGMII PHY
- PMIC
- SOM connector providing:
- FEC GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 2.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw73xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW73xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- on-board 802.11abgnac 1x1 WiFi and Bluetooth 5.2
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 2x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Gateworks imx8mp-venice-gw72xx-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW72xx Baseboard contains the following:
- 1x RJ45 GbE (eQoS from SOM)
- 1x RJ45 GbE (PCI)
- off-board I/O connector with MIPI-CSI (3-lane), MIPI-DSI (4-lane),
- off-board I/O connector with RS232/RS485
- off-board I/O connector with SPI
- off-board I/O connector with I2C, UART, and GPIO
I2C, I2S and GPIO
- microSD (1.8V/3.3V)
- GPS
- Accelerometer
- EERPOM
- USB 3.0 Hub
- Front Panel bi-color LED
- re-chargeable battery (for RTC)
- PCIe clock generator
- PCIe switch
- 1x USB Type-A host socket with USB 3.0 support
- 1x USB OTG with USB 2.0 support
- 1x MiniPCIe socket with PCI and USB 2.0
- 1x MiniPCIe socket with SIM, PCI/USB 3.0 (mux), and USB 2.0
- Wide range DC input supply
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Linux microPlatform uses an rngb device in optee-os in boot scheme
SPL -> OPTEE -> U-Boot. To make rngb available for optee-os, enable
it in SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
With enabled SKIP_LOWLEVEL_INIT, the weak function timer_init() is
used in the SPL build. For iMX6 SoC, this leads MMC to fail once
u-boot proper is booted due to a timing issue.
Always use iMX-specific timer_init() in SPL to fix timing issues.
Fixes: be277c3a89 ("imx: mx7: avoid some initialization if low level is skipped")
Signed-off-by: Michael Scott <mike@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Now we have to use UCLASS_SM driver instead of
raw smc_call() function call.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-9-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
The common.h header should always be first, followed
by other headers in order, then headers with directories,
then local files.
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230921081346.22157-8-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
A follow-up to commit 842fb5de42
("drivers: use devfdt_get_addr_size_index_ptr when cast to pointer")
and commit 320a1938b6
("drivers: use devfdt_get_addr_index_ptr when cast to pointer").
In addition to using the *_ptr variants of these functions where the
address is cast to a pointer, this also changes devfdt_get_addr_*() to
dev_read_addr_*() in a few places. Some variable and field types are
changed from fdt_addr_t or phys_addr_t to void* where the cast was
happening later.
This patch fixes a number of compile warnings when building a 32bit
U-Boot with CONFIG_PHYS_64BIT=y. In some places, it also fixes error
handling where the return value of dev_read_addr() etc. was checked for
NULL instead of FDT_ADDR_T_NONE.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
Make that condition more generic by checking if the memory controller
driver is enabled instead of using the EVM's config.
Signed-off-by: Dominik Haller <d.haller@phytec.de>
The following commit syncs the device tree from Linux tag
v6.6-rc1 to U-boot and fixes the following to be compatible with
the future syncs -
- Include k3-am68-sk-base-board.dts file
Remove the duplicated pinmuxes from r5 and -u-boot.dtsi files and
include k3-am68-sk-base-board.dts for Linux fixes to propagate
to U-boot.
- Fixing the mcu_timer0
Remove timer0 and use the mcu_timer0 defined in mcu-wakeup.dtsi
- Fixing secure proxy nodes
Linux DT now have these nodes defined so remove them and rename to
use the Linux DT ones.
- Remove cpsw node
The compatible is now fixed and the node is not required in
-u-boot specifically
- Remove aliases and chosen node
Use these from Linux and don't override when not required.
- Remove /delete-property/ from sdhci nodes
We have the necessary clock and dev data so remove these.
- Remove dummy_clocks and fs_loader0
These weren't being used anywhere so remove it.
- Remove mcu_ringacc override
All these have been put in a single commit to not break the
bisectability.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commit syncs the device tree from Linux tag
v6.6-rc1 to U-boot and fixes the following to be compatible with
the future syncs -
- Include k3-j721s2-common-proc-board.dts file
Remove the duplicated pinmuxes from r5 and -u-boot.dtsi files and
include k3-j721s2-common-proc-board.dts for Linux fixes to propagate
to U-boot.
- Fixing the mcu_timer0
Remove timer0 and use the mcu_timer0 defined in mcu-wakeup.dtsi
- Fixing secure proxy nodes
Linux DT now have these nodes defined so remove them and rename to
use the Linux DT ones.
- Remove cpsw node
The compatible is now fixed and the node is not required in
-u-boot specifically
- Remove aliases and chosen node
Use these from Linux and don't override when not required.
- Remove /delete-property/ from sdhci nodes
We have the necessary clock and dev data so remove these.
- Remove dummy_clocks and fs_loader0
These weren't being used anywhere so remove it.
- Remove mcu_ringacc override
All these have been put in a single commit to not break the
bisectability.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
mcu_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices lsit so it an be enabled via the k3 power controller.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The update causes instability in am68-sk boards so revert the patch in
the meantime till fix is available.
This reverts commit f1edf4bb6a.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Sync j7200 dts with Linux 6.6-rc1
- k3-j7200-r5-common-proc-board.dts now inherits from
k3-j7200-common-proc-board.dts instead of k3-j7200-som-p0.dtsi. This
allows us to trim down the r5 file considerably by using existing
properties
- remove pimux nodes from r5 file
- remove duplicate nodes & node properties from r5/u-boot files
- mcu_timer0 now used instead of timer1
mcu_timer0 device id added to dev-data.c file in order to work
- remove cpsw node
This node is no longer required since the compatible is now fixed
- remove dummy_clock_19_2_mhz
This node wasn't being used anyhere, so it was removed
- remove dummy_clock_200mhz
main_sdhci0 & main_sdhci1 no longer need dummy clock for eMMC/SD
- fix secure proxy node
mcu_secproxy changed to used secure_prxy_mcu which is already
defined in k3-j7200-mcu-wakeup.dtsi
- removed &mcu_ringacc property override since they're present in
v6.6-rc1
Signed-off-by: Reid Tonking <reidt@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
mcu_timer0 is now used as the tick timer in u-boot, so this adds the
timer to the soc device list so it can be enabled via the k3 power
controller.
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Reid Tonking <reidt@ti.com>
ao-secure node can be used to get information about the board,
so, for example, using show_board_info() we can get following
information for board with Meson A1 SoC:
SoC: Amlogic Meson A1 (A113L) Revision 2c:a (1:a)
Signed-off-by: Alexey Romanov <avromanov@salutedevices.com>
Link: https://lore.kernel.org/r/20231010100623.74475-3-avromanov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
This patch adds basic clock driver for Amlogic A1 Family which supports
enabling/disabling some gates, getting frequencies and setting rate
with limited reparenting.
Signed-off-by: Igor Prusov <ivprusov@salutedevices.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230925155209.130671-3-ivprusov@salutedevices.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
All K3 boards now are secure by default, instead of setting this in each
defconfig, make it implied by the ARCH config.
The only exception is IOT2050, which I do not believe will have any
problems with being a TI_SECURE_DEVICE, but for now turn it off to keep
its config the same.
Signed-off-by: Andrew Davis <afd@ti.com>
Tested-by: Tom Rini <trini@konsulko.com>
As the code to switch an ARM core from secure to the non-secure state
needs to know the base address of the Generic Interrupt Controller
(GIC), we read an Arm Cortex defined system register that is supposed to
hold that base address. However there are SoCs out there that get this
wrong, and this CBAR register either reads as 0 or points to the wrong
address. To accommodate those systems, so far we use a macro defined in
some platform specific header files, for affected boards.
To simplify future extensions, replace that macro with a Kconfig variable
that holds this override address, and define a default value for SoCs
that need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sam Edwards <CFSworks@gmail.com>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Jan Kiszka <jan.kiszka@siemens.com>
Distinguish more clearly between source files meant for producing .dtb
from those meant for producing .dtbo. No functional change, as we
currently have rules for producing a foo.dtbo from either foo.dts or
foo.dtso.
Note that in the linux tree, all device tree overlay sources have been
renamed to .dtso, and the .dts->.dtbo rule is gone since v6.5 (commit
81d362732bac). So this is also a step towards staying closer to linux
with respect to both Kbuild and device tree sources.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Apple's M2 Ultra SoC are somewhat similar to the M1 Ultra but needs
a tweaked memory map as the M2 Pro/Max SoCs. USB, NVMe, UART, WDT
and PCIe are working with the existing drivers.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The ARMv8.5 architecture extension defines architectural RNDR/RNDRRS
system registers, that provide 64 bits worth of randomness on every
read. Since it's an extension, and implementing it is optional, there is
a field in the ID_AA64ISAR0_EL1 ID register to query the availability
of those registers.
Add a UCLASS_RNG driver that returns entropy via repeated reads from
those system registers, if the extension is implemented.
The driver always binds, but checks the availability in the probe()
routine.
This helps systems which suffer from low boot entropy, since U-Boot can
provide entropy via the generic UEFI entropy gathering protocol to the OS,
at an early stage.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A53 U-Boot proper got broken because nodes marked as 'bootph-pre-ram'
are no longer available in U-Boot proper before relocation.
Fix this by marking all nodes in u-boot.dtsi as 'bootph-all'.
Fixes: 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as pre-reloc after relocation")
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Since commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node
as pre-reloc after relocation") A53 u-boot proper is broken. This is
because nodes marked as 'bootph-pre-ram' are not available at u-boot
proper before relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
Fixes: 69b19ca67b ("arm: dts: k3-j721e: Sync with v6.6-rc1")
Cc: Neha Francis <n-francis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Tom Rini <trini@konsulko.com> # J721E-EVM GP
Tested-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
This is now done using binman but this file was leftover and is now
unused, remove it.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Since commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node
as pre-reloc after relocation") A53 u-boot proper is broken. This is
because nodes marked as 'bootph-pre-ram' are not available at u-boot
proper before relocation.
To fix this we mark all nodes in u-boot.dtsi as 'bootph-all'.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Some functions are not used outside this file, so make them static.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
PPA was a secure firmware developed in-house which is no longer
supported and replaced by TF-A quite some years ago. Drop support
for it.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use uintptr_t instead of phys_addr_t where appropriate, so passing the
addresses to writel() doesn't result in compile warnings when PHYS_64BIT
is set for 32bit builds (which is actually a useful configuration, as
the K3 SoC family boots from an R5 SPL, which may pass bank information
based on gd->bd->bi_dram to fdt_fixup_memory_banks() etc., so PHYS_64BIT
is needed for fixing up the upper bank).
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
- None of the callers perform error checking and based on the non-empty
versions of this function, there's no checking to be done, so make
this a void.
- Add a default weak version of the function.
- Remove the empty versions of exynos_init now that we have a weak
version.
Signed-off-by: Tom Rini <trini@konsulko.com>
The SelectMAP configuration interface provides an 8-bit,
16-bit or 32-bit bidirectional data bus interface to the Versal FPGA
configuration logic that can be used for both configuration and readback.
A connected microcontoller to the SelectMAP interface can load boot
image with bitstream, TF-A (ARM Trusted Firmware) and U-Boot.
This commit adds the missing identification of the SelectMAP mode.
Signed-off-by: Polak, Leszek <LPolak@arri.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Stefan Roese <sr@denx.de>
Link: https://lore.kernel.org/r/DU0PR07MB8419F7765892CDBCE7D559C5C8CFA@DU0PR07MB8419.eurprd07.prod.outlook.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
