This board is configured with CONFIG_USB1_VBUS_PIN="PH24", but no
regulator exists in its device tree. Add the regulator, so USB will
continue to work when the PHY driver switches to using the regulator
uclass instead of a GPIO.
Update the device tree here because it does not exist in Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCZDBwUw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXL3+AJ9EkQKAWXZtlYdAOVl4/nzJnuTCAQCfY58zkDsw
TnAlwmMGWFl3RF6yGXY=
=uYUp
-----END PGP SIGNATURE-----
Merge tag 'video-20230407' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix building sandbox without SDL
- improve tegra DC driver to work with panel ops and implement
native 180 degree panel rotation support
- add T30 support to tegra DC driver
- add DSI driver (based on mainline Linux one with minor
adjustments, only T30 tested)
- add get_display_timing ops to simple panel driver
- extend simple panel driver to use it for MIPI DSI panels
which do not require additional DSI commands for setup
On popular request make the display driver from T20 work on T30 as
well. Turned out to be quite straight forward. However a few notes
about some things encountered during porting: Of course the T30 device
tree was completely missing host1x as well as PWM support but it turns
out this can simply be copied from T20. The only trouble compiling the
Tegra video driver for T30 had to do with some hard-coded PWM pin
muxing for T20 which is quite ugly anyway. On T30 this gets handled by
a board specific complete pin muxing table. The older Chromium U-Boot
2011.06 which to my knowledge was the only prior attempt at enabling a
display driver for T30 for whatever reason got some clocking stuff
mixed up. Turns out at least for a single display controller T20 and
T30 can be clocked quite similar. Enjoy.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS TF T30
Tested-by: Jonas Schwöbel <jonasschwoebel@yahoo.de> # Surface RT T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Add board code for R8A779G0 V4H White Hawk board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add DTs for R8A779G0 V4H White Hawk CPU and BreakOut boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tho Vu <tho.vu.wh@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message
Rename DTs to match Linux, which has dash between white-hawk]
Add R8A779G0 V4H DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT support for R8A779G0 (R-Car V4H). Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Phong Hoang <phong.hoang.wz@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add board code for R8A779F0 S4 Spider board.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Synchronize configuration symbols which are now switched to Kconfig
Mallocate gd->bd->bi_boot_params, i.e. drop the assignment
Sort headers, use clrbits_le32(), use BIT macros where appropriate
Use CONFIG_SYS_CLK_FREQ for counter frequency instead of custom macro]
Add DTs for R8A779F0 S4 Spider CPU boards and Breakout boards.
Based on Linux next 20230228 DTs up to
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Add R8A779F0 S4 DT extras for U-Boot.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Update compatible string to match latest upstream]
Add initial DT for R8A779F0 S4 SoC. Based on Linux next
commit 058f4df42121 ("Add linux-next specific files for 20230228")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync with Linux next 20230228, update commit message]
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LX2160A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS1088A based boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
Add WDT reboot bindings on DH i.MX6 DHSOM to permit the platform
to reboot via WDT in U-Boot. These are custom U-Boot bindings,
hence they are placed in -u-boot.dtsi .
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
J721e SK has been broken since at least March 2022.
The main-navss and mcu-navss nodes were renamed and this caused the
A72 SPL to fail early in the boot even before the serial port was
enabled. Fix this.
A later patch series between v2022.07 and v2022.10 additionally broke
boot on this board by introducing hbmc nodes which are not present on
this board. The right fix is to disable these by default in the SOC
dtsi file, but for now we can also disable them in the u-boot dtsi.
With both these fixed, we can now boot the j721e SK board fully from
mainline u-boot.
Fixes: 58d61fb5a7 ("arm: dts: k3-j721e-sk: Add initial A72 specific dts support")
Fixes: 297daac43a ("arm: dts: k3-j721e-mcu-wakeup: Add HyperBus Controller node")
Reported-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
[gadiyar@ti.com: update commit description]
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Bryan Brattlof <bb@ti.com>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCZCaU0Q8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76YCKgCgk4OueoIggmes+Ccj8bu1BcQbrfYAoJAgMeKE
It0hrVAifD62TPb2rmHt
=hFVG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-next-20230331' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx into next
u-boot-imx-next-20230331 for next
---------------------------------
CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/15819
i.MX patches queued for next:
- Conversions to DM_SERIAL
- Fixes for Toradex boards
- Gateworks Boards
- i.MX8ULP
- EQoS support / fixes, changes in boards
The assigned-clock no longer have to be dropped, the clock are now
defined in clk-imx8mp.c and used by DWMAC driver to configure the
DWMAC clock. Drop the workarounds from U-Boot specific DT extras.
Signed-off-by: Marek Vasut <marex@denx.de>
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK3 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
The PHY nodes may be activated via DTO in case another SoM variant
is populated into the development kit. Do not delete the nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either external RGMII PHY or
LAN8740Ai RMII PHY on the SoM attached to FEC MAC. Add pin mux
settings for both options, so that DT overlay can override these
settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The i.MX8MP DHCOM SoM may come with either KSZ9131RNXI RGMII PHY
or LAN8740Ai RMII PHY on the SoM attached to EQoS MAC. Add pin
mux settings for both options, so that DT overlay can override
these settings on SoM variant with the LAN8740Ai PHY.
Signed-off-by: Marek Vasut <marex@denx.de>
The current variant of the SoM has LAN8740Ai PHY connected to EQoS
strapped to MDIO address 0 , adjust the MDIO address to match the
hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
A388 Clearfog MMC is either SD Card or eMMC with different behaviour for
both. Setting the device to non-removable in the u-boot.dtsi allows both
to correctly detect the device.
Signed-off-by: Martin Rowe <martin.p.rowe@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Originally, the mmc aliases node was present in imx6qdl-pico.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a boot regression in which the eMMC card cannot be found anymore.
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the eMMC (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
The M.2 slots of the related IOT2050 variant need to be configured
according to the plugged cards. This tries to detect the card using the
M.2 configuration pins of the B-key slot. If that fails, a U-Boot
environment variable can be set to configure manually. This variable is
write-permitted also in secure boot mode as it is not able to undermine
the integrity of the booted system.
The configuration is then applied to mux the serdes and to fix up the
device tree passed to or loaded by the bootloader. The fix-ups are
coming from device tree overlays that are embedded into the firmware
image and there also integrity protected. The OS remains free to load
a device tree to which they do not apply: U-Boot will not fail to boot
in that case.
Based on original patch by Chao Zeng.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add support for the M.2 board based on the iot2050 advanced board.
The board has two m.2 connectors, one is B-keyed, the other E-keyed.
The B-key slot can connect 5G/SSD devices, and E-key can be used for
WIFI/BT devices.
This variant is covered by PG2 firmware image.
Signed-off-by: chao zeng <chao.zeng@siemens.com>
[Jan: align DT to kernel, polish wording]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Use external blob otpcmd.bin to replace the 0xff filled OTP programming
command block to create a firmware image that provisions the OTP on
first boot. This otpcmd.bin is generated from the customer keys using
steps described in the meta-iot2050 integration layer for the device.
Based on original patch by Baocheng Su.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Add hashes and configuration signature stubs to prepare verified boot
of main U-Boot by SPL.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The latest version of the binary-only firmware parts come in a combined
form of FSBL and sysfw containers. This implies some layout changes to
the generated firmware image but also makes handling of artifacts much
simpler (4 files less). The env locations will not change, just the
space reserved for U-Boot will shrink from 4 to 3 MB - still plenty of
space left in practice.
Adjust configuration and documentation accordingly.
Along this change, add a new reservation for update commands of the
user-controlled OTP part. A specific userspace tool will fill it, and
the FSBL will evaluate it during boot. This reservation will use 64K of
the former sysfw section.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Refactor according to the entry `fit: Entry containing a FIT` of
document tools/binman/README.entries.
As the generator uses the device tree name for the config description,
board_fit_config_name_match requires a small adjustment as well.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: re-add now required CONFIG_OF_LIST, update config matching]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to different signature keys, the PG1 and the PG2 boards can no
longer use the same FSBL (tiboot3). This makes it impossible anyway to
maintaine a single flash.bin for both variants, so we can also split the
build.
A new target is added to indicates the build is for PG1 vs. PG2 boards.
Hence now the variants have separated defconfig files.
The runtime board_is_sr1() check does make no sense anymore, so remove
it and replace with build time check.
Documentation is updated accordingly. New binary artifacts are already
available via meta-iot2050.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[Jan: refactor config option into targets, tweak some wordings]
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
After the conversion to DM_SERIAL in commit 01f372d8d6 ("udoo_neo:
Select DM_SERIAL and drop iomux board level init") the SPL log is gone
and the U-Boot proper log becomes incomplete:
Core: 80 devices, 18 uclasses, devicetree: separate
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: eth0: ethernet@2188000
Hit any key to stop autoboot: 0
Introduce the u-boot.dtsi file that passes the u-boot,dm-pre-reloc
properties to the relevant nodes so that UART can be used early in SPL.
With this change, the complete SPL and U-Boot messages are seen again.
Signed-off-by: Fabio Estevam <festevam@denx.de>
While this change is correct for v2023.04 it is not correct for next
(where this is right now) nor post-v2023.04.
This reverts commit 8653e5d3b7.
Signed-off-by: Tom Rini <trini@konsulko.com>
The Rockchip timer driver has been renamed after the fall back compatible.
There's no need to replace the timer compatible in rk3188-radxarock-u-boot.dtsi
anymore, so remove.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot from eMMC on a ROCK 3 Model A result in the following:
U-Boot SPL 2023.04-rc3 (Mar 11 2023 - 17:24:48 +0000)
Trying to boot from MMC1
Card did not respond to voltage select! : -110
spl: mmc init failed with error: -95
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
The sdhci node is missing in board device tree, sync device tree from
linux v6.3-rc1 to fix booting from eMMC. Also disable sdmmc2 and uart1
nodes related to using a WiFi and BT module in the M2 slot.
Fixes: b44c54f600 ("arm64: dts: rockchip: rk3568: Add Radxa ROCK 3 Model A board support")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The boot source node path for emmc is using the old sdhci name.
Replace with correct mmc name and also add same-as-spl to boot order.
Fixes: 0d61f8e5f1 ("rockchip: rk3568: add boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Running U-Boot on a ROCK 3 Model A result in the following:
No serial driver found
resetting ...
no sysreset
### ERROR ### Please RESET the board ###
Replace bootph- props with u-boot,dm- props to fix this.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Per Andre:
[T]hese two patches containing just devicetree updates for
Allwinner boards.
I was still hoping for a review, since we cannot import the files from
the Linux tree verbatim, but managed to write some filter script that
convinced me that the changes are fine.
The files are from Linux v6.2-rc2, but are identical to the v6.2
release.
Tag the serial nodes with bootph-all in order to have these nodes and
the drivers available before relocation.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Sync the serial nodes of the LS208XA RDB/QDS boards with their
representation in Linux. We also imported the clockgen and sysclk nodes
which are dependencies.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the serial nodes under the soc node. No changes are made to the
nodes, just their location is changed.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The u-boot dts for these boards do not have an soc node, unlike its
Linux counterpart. This patch just adds the soc node as seen in Linux,
the next patches will move some nodes under it.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When the first device tree description was added for the ethernet nodes,
the 2 10G ports on the LS1088ARDB were wrongly described as 'xgmii'.
Fix this by replacing the two last occurrences of 'xgmii' in the device
trees of the Layerscape DPAA2 devices.
Fixes: 68c7c008e8 ("arm: dts: ls1088ardb: add DPMAC and PHY nodes")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The Odroid Go Ultra has 2 chained PMICs RK818 and RK818, and needs
an adjustment on the BUCK and LDO values.
Add the initial regulators values in -u-boot.dtsi & run the initial
regulator setup in a new odroid-go-ultra board.
Proper OTG and BOOST regulators are still missing to have USB-A
host properly working.
Link: https://lore.kernel.org/r/20230210-u-boot-odroid-go-ultra-pmics-setup-v1-1-1f16d62b76af@linaro.org
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable support for sysinfo on R-Car D3 Draak board. The sysinfo is used
e.g. to access and decode board-specific information and then in turn
used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77995.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
Add new sysinfo IDs for R-Car V3H Condor/Condor-I .
Enable support for sysinfo on R-Car V3H Condor/Condor-I. The sysinfo is
used e.g. to access and decode board-specific information and then in
turn used by board-info to print those information.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Drop compatible from I2C node, this is in r8a77980.dtsi already.
Drop status = "okay" from EEPROM node.
Add dts: tag.
Update the commit message, note the new sysinfo IDs.
Fix Kconfig EEPROM address to be 0x50 and match the DT, sync config.]
By default enable nand-on-flash-bbt DT flag, so that driver always refers
to the bad block table(bbt) present on the flash device.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-5-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
DC3 nand node is not correct, it is showing all partitions under
controller node directly. Create two sub nand nodes with partitions for
each.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230224050709.30014-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The latest SOM specification doesn't enforce certain MIO lines allocated
for ethernet or ethernet controller itself. That's why remove comment about
it which is likely there from early version of specification.
Also removed the same comment from pinctrl node. It is clear that it has to
be defined for different carrier cards.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9406377bf2c391ac0200670511bd6b0edb097c96.1676880543.git.michal.simek@amd.com
Since the zynqmp boards can run upstream OP-TEE, and having the DT node
present doesn't cause any side effects add it in case someone tries to
load OP-TEE.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/r/20230216133921.866786-1-ilias.apalodimas@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
The pl330 DMA controller provides number of DMA channels and requests
through its registers, so duplicating this information (with a chance of
mistakes) in DTS is pointless. Additionally the DTS used always wrong
property names which causes DT schema check failures - the bindings
documented 'dma-channels' and 'dma-requests' properties without leading
hash sign.
Reported-by: Rob Herring <robh@kernel.org>
Suggested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/20220430121902.59895-2-krzysztof.kozlowski@linaro.org
Since we need to support legacy phys with the dwc3 controller,
we enable this quirk on the zynqmp platforms.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Link: https://lore.kernel.org/r/20221023215649.221726-1-m.grzeschik@pengutronix.de
Signed-off-by: Michal Simek <michal.simek@amd.com>
The node names should be generic and DT schema expects certain pattern:
xilinx/zynqmp-zcu100-revC.dtb: leds: 'vbus-det' does not match any of the regexes: '(^led-[0-9a-f]$|led)', 'pinctrl-[0-9]+'
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20221125144136.477171-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Michal Simek <michal.simek@amd.com>
cdns prefix was deprecated and replaced by xlnx one in upstream Linux. Also
U-Boot driver has been updated to support new compatible string that's why
it is time to remove it and deprecate it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
AM62A7-SK board has 4GB LPDDR4 Micron MT53E2G32D4DE-046 AUT:B part
but only 2GB was enabled early.
Enable full 4GB memory by updating the latter 2GB memory region
which gets mapped to 0x0880000000 i.e. DDR16SS0_SDRAM as referred in
Table 2-1. AM62A Common SoC Memory of AM62Ax TRM [1].
[1] : https://www.ti.com/lit/zip/spruj16
Logs: https://gist.github.com/devarsht/e85b6af89c01ddadb3a62f3e5f196af8
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Synchronize devicetree sources with Linux v6.2.
- Use GIC interrupt definitions
- Add reg properties in USB-glue and SoC-glue node
- Fix node names to follow the generic names list in DT specification
- Add L2 cache and AHCI nodes
- Update nand and pcie nodes
- And some trivial fixes
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
UniPhier DT applies its own USB node for U-Boot due to the USB driver
constrains. After solving this issue, u-boot allows the original USB node.
After switching USB node, synchronization of USB node with Linux becomes
possible.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 64-bit SoCs, from arch/arm64/boot/dts/allwinner.
This enables GPU power management in the kernel for the H6, enables
Bluetooth on the Pinebook, and adds USB to the H616 devices (just
for newer Linux kernels at the moment, U-Boot support is pending).
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Sync the devicetree files from the Linux kernel repo, v6.2-rc2.
This is covering the 32-bit SoCs, from arch/arm/boot/dts.
This enables some new devices for the F1C100s family, though this is of
little relevance to U-Boot itself.
The H3 gains the "phys" property for the first USB controller, which
prevents an error message when U-Boot's USB stack comes up, and allows
using this port in host mode.
As before, this omits the non-backwards compatible changes to the R_INTC
controller, to remain compatible with older kernels.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmP+97wcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyExpB/wLQVjeBM+sEcABzT52
c7qtAvtgl/UbPedYyMz2YorL5BcHsdmBbGfSzBISEc8kLdtAVMTKAaqvN7msaJFX
MwPIZAXWd8cPM0EA7wSyjYDGOvcEzGWF7oxSbeq+j7M2kibvsQLGW7iaY5cjFIzx
QPQ19T2tyX3jrsy8dxCsPivB70vB/3lqiEmCZX2UddsjxrL6Vt2H3k6O+/Ler5wS
/nJIzKLDPc+aDZSv+aevDlJZi1eGkpTHldNaHXqdYILzvnXIQmA6kP0mWPZ9g6wZ
s6ed1N5VeiS4j6oH5Woj3nDKny7P3AKSd9+c/eXfbtdia2D0yBHtiHQauIwNPCd3
wAcH
=/Vn2
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91
First set of u-boot-at91 fixes for the 2023.04 cycle:
This fixes set include one clock index fix for sama7g5 and two board
configuration alignments for pm9g45.
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The cpuid on RK3568 is located at 0xa instead of 0x7 as all other SoCs.
Add and use a CFG_CPUID_OFFSET to define this offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Booting from SDMMC is one of the fast and easy booting methods
for initial support of any SoC to upstream more features.
This patch is trying to add the sdmmc node for rk3588 and added
as u-boot specific node in -u-boot.dtsi as upstream Linux is not
supporting yet.
As soon as Linux supports it, a sync of the Linux device tree
would eventually drop this node.
Clock properties as added according to the rockchip mmc driver
but the actual definition might add scmi clocks into 0 and 1
indexes. This is due to scmi clock are not supporting in upstream
U-Boot. Properly addition of scmi clock would eventually follow
sdmmc clock definition of Linux once they upstreamed.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RK3588 SoC to boot the SPL.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
commit <a5079a534554> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A IO")
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neu6 needs to mount on top of associated Edgeble IO boards for
creating complete platform solutions.
Enable eMMC for now to boot Linux successfully.
commit <3d9a2f7e7c5e> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A SoM")
Add support for Edgeble Neu6 Model A SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This initial version supports CPU, dma, interrupts, timers, UART and
SDHCI (everything necessary to boot Linux on this system on chip) as
well as Ethernet, I2C, PWM and SPI.
The DT is split into rk3588 and rk3588s, which is a reduced version
(i.e. with less peripherals) of the former.
commit <9fb232e9911f> (" arm64: dts: rockchip: Add base DT for rk3588
SoC")
commit <d68a97d501f8> ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add gpio-ranges property to GPIO nodes so that the bank ID can
be correctly derived for each GPIO bank.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync rk3566 and rk3568 from the mainline Linux kernel (6.2-rc2 as of
this writing).
Note that this will rename the rk3568-evb to rk3568-evb1-v10.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the gpio-ranges property to each GPIO node for use in deriving
the correct bank ID. Note that invoking "gpio status -a" no longer
causes the board to hit a "Synchronous Abort".
Fixes: 537b1a2774 ("rockchip: add px30 devicetrees")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
combphy1 is failing to probe due to unhandled assigned-clocks and
assigned-clocks-rates.
=> usb start
starting USB...
Bus usb@fd000000: Failed to get PHY1 for usb@fd000000
Port not available.
Bus usb@fd800000: USB EHCI 1.00
There is no real requirement for them in U-Boot to handle, hence
mark them as deleted-properties for the probe to success
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Add support for Radxa CM3 IO Board defconfig and -u-boot.dtsi
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Radxa Compute Module 3(CM3) IO board an application board from Radxa
and is compatible with Raspberry Pi CM4 IO form factor.
Specification:
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- Phone jack
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
linux-next commit for the same,
commit <8f19828844f2> ("arm64: dts: rockchip: Fix compatible for Radxa
CM3")
Add support for Radxa CM3 IO Board.
Co-developed-by: FUKAUMI Naoki <naoki@radxa.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Co-developed-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
