UART does not use the UART FIFO, but we should also not rely that
the UART FIFO is diabled by default. For instance, when loading
U-Boot using the boot ROMs serial downloader protocol over UART,
FIFO is enabled at U-Boot start time.
This patch disables the RX and TX FIFO, sets back their thresholds
and flushes them.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The status register 1 (S1) is not writeable, hence we should not
write it. In order to clear the RDRF flag we only need to read
the data register.
Also, when stressing U-Boot a lot with serial input, an overflow can
occur which asserts the S1_OR flag (while not asserting the S1_RDRF
flag). To clear this flag we again just need to read the data
register, hence add this flag to the abort conditions for the while
loop.
Insert a compiler barrier to make sure reading the data register
gets executed after reading the status register.
Signed-off-by: Stefan Agner <stefan@agner.ch>
On vybrid, lpuart's registers are 8-bit. On LS102xA, lpuart's registers
are 32-bit. This patch adds the support for 32-bit registers on
LS102xA.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
The nios2-yanu.h contains hardware registers and bits of
opencores yanu. As there is no other user of this header
, it should be moved into the driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
CC: Renato Andreola <renato.andreola@imagos.it>
The nios2-io.h defines hardware registers and bits of several FPGA
IP cores. It could be divided in to the specific drivers, including
altera timer, altera sysid, altera uart and altera jtag uart. The
altera pio and altera spi drivers use their own hardware definitions.
The removal of nios2-io.h will help modularity and maintenance.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
R8A7780 and R7A7791 of rmobile supports External Clock mode, and these uses
different from Internal Clock mode registers and calculations to the baud rate
setting. This adds function for External Clock mode.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R8A7794 has DL and CKS register, and these registers are used in external clock
mode. This adds support these for R8A7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use CONFIG_SOC_KEYSTONE in common places instead of defining
a lot of "if def .. || if def " for different Keystone2 SoC types.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
For sandbox we have a fallback console which is used very early in
U-Boot, before serial drivers are available. Rather than try to guess
when to switch to the real console, add a flag so we can be sure. This
makes sure that sandbox can always output a panic() message, for example,
and avoids silent failure (which is very annoying in sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Just for type checking.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The function still returns the same value.
The comment block is no longer necessary because our intention is
clear enough by using DIV_ROUND_CLOSEST() macro.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OMAP1610 is defined, the code returning the fixed value (26)
is enabled. But this case is covered by the following code.
(CONFIG_SYS_NS16550_CLK + (gd->baudrate * (MODE_X_DIV / 2))) /
(MODE_X_DIV * gd->baudrate)
= (48000000 + (115200 * (16 / 2))) / (16 * 115200)
= 48921600 / 1843200
= 26
The "#ifdef CONFIG_OMAP1610" was added by commit 6f21347d more than
ten years ago. In those days, the divide-and-round was not used.
I guess that is why this weird code was added here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Rishi Bhattacharya <rishi@ti.com>
Bit 7 of UCR3 is described in the i.MX3x/i.MX5x/i.MX6x
reference manuals as follows:
Autobaud Detection Not Improved-. Disables new features of
autobaud detection (See Baud Rate Automatic Detection
Protocol, for more details).
0 Autobaud detection new features selected
1 Keep old autobaud detection mechanism
On at least i.MX6DQ, i.MX6DLS and i.MX53, the "new features"
occasionally cause the receiver to get out of sync and
continuously produce received characters of '\xff'.
This patch disables the "new feature" on all boards, since
there's no support for auto-baud in U-Boot on any of them.
More details are available in this post on i.MX Community:
https://community.freescale.com/message/403254
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
's/zynq_serial_initalize/zynq_serial_initialize/g'
serial_initialize is used by all serial drivers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:182:22: warning: symbol 'uart_zynq_serial0_device' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:185:22: warning: symbol 'uart_zynq_serial1_device' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
It is useful for Cltl-C to be handled by U-Boot as it is on other boards.
But it is also useful to be able to terminate U-Boot with Ctrl-C.
Add an option to enable signals while in raw mode, and make this the
default. Add an option to leave the terminal cooked, which is useful for
redirecting output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple LCD driver which uses SDL to display the image. We update the
image regularly, while still providing for reasonable performance.
Adjust the common lcd code to support sandbox.
For command-line runs we do not want the LCD to be displayed, so add a
--show_lcd option to enable it.
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This is required for proper functionality on big-endian targets.
Memory-mapped registres of ARC UART are not 32-bit words but 8-bit bytes
so on little-endian target either acessor (_l or _b) works fine.
On big-endian only _b accessors works as expected.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Tom Rini <trini@ti.com>
Remove hard coded frequencies and use Zynq's clock framework to obtain
the UART clock frequency.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The implementation of oc_serial_setbrg() for CONFIG_SYS_NIOS_FIXEDBAUD and
!CONFIG_SYS_NIOS_FIXEDBAUD are very similar.
Add a baudrate variable and set it to either CONFIG_BAUDRATE or gd->baudrate.
Then we can unify the code for both cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Fix build error due to missing include of serial.h and a trivial typo.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys)
FPGA Boards such as ARCAngel4/ML50x
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
This driver is no longer used, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
This patch fix the u-boot shell problem on TRATS2 board.
- If hold the key while booting is in progress,
white spaces are written in u-boot shell.
Set Automatically clears after resetting Rx FIFO.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <trini@ti.com>
For LPC32XX high-speed UART it is required to send a carriage return
symbol along with line feed. The problem was introduced in e503f90a
commit.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Staticize local functions in xuartlite driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Simek <monstr@monstr.eu>
This adds the preset value to register, and setup of baudrate.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The former SH/SCIF driver had calculated baudrate based on CONFIG_SYS_CLK_FREQ.
The newest SH/SCIF needs calculation of the clock for SCIF.
This patch defines clock CONFIG_SH_SCIF_CLK_FREQ for SCIF and changes it to
CONFIG_SH_SCIF_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling serial_s3c44b0.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Use default_serial_puts() instead of its own implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
Register arm_dcc with drivers/serial/serial.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removed stdio structure ops support on arm_dcc
driver, and need to register with serial core
so-that it can access like remianing serial drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The mv_udc driver is broken for a while and doesn't even compile.
This patch fixes the issues and gets the driver into working state
again. This driver was tested on Freescale i.MX233/i.MX28 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds FDT support to the serial s5p driver.
At present disabling the serial console (from the device tree) crashes
U-Boot. Add checks for this case, so that execution can continue without
a serial console.
It also enables the serial_s5p driver recognize the silent_console option.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds lpuart support for Vybrid VF610 platform.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
This patch enables the uart tx/rx fifo. Now that fifo is enabled,
the uart read/write functions are modfied to check the UFSTAT register
for fifo status instead of UTRSTAT (as required with fifo's enabled).
Tested by booting linux kernel. Before enabling tx/rx fifo
"Uncompressing linux" message is garbled and after enabling it is proper.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
- Move blackfin serial driver to the generic driver folder.
- Move blackfin serial headers to blackfin arch head folder.
- Update the include path to blackfin serial header in start up code.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Flush UART3 xmit on enable if TEMT is broken
On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.
Signed-off-by: Manfred Huber <man.huber@arcor.de>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
This cast does not seem correct, since we should be writing to a pointer,
not a ulong.
This fixes the following warning on nds32:
-ns16550.c:49: warning: passing argument 2 of 'writeb' makes pointer from integer without a cast
Signed-off-by: Simon Glass <sjg@chromium.org>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
Implements the tstc() interface for the serial driver. Multiplexing
the console between the serial port and a keyboard uses a polling
method of checking if characters are available; this means that the
serial console must be non-blocking when attempting to read
characters.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 8b710b1 started removing code for the unmaintained "ns9750dev"
board; the board support is still broken, and not included anywhere in
the Makefile or boards.cfg. Remove the remaining dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_ARM_DCC_MULTI should be also removed in the patch
"serial: Remove CONFIG_SERIAL_MULTI from serial drivers"
(sha1: a382725060)
Because the driver defines serial_* functions
which cause conflict with serial.c (multiple definition of serial_*)
Removing CONFIG_SERIAL_MULTI function also require to define
default_serial_console for cases where another serial driver
is not available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Some platforms (e.g. IGEPv2 board) has a broken ns16550 UART that
does not set the TEMT bit when the transmitter is empty in SPL.
This makes U-Boot to hang while waiting for TEMT to be set.
Add a new option to avoid this:
CONFIG_SYS_NS16550_BROKEN_TEMT
16550 UART set the Transmitter Empty (TEMT) Bit when all output
has finished and the transmitter is totally empty. U-Boot waits
for this bit to be set to initialize the serial console. On some
broken platforms this bit is not set in SPL making U-Boot to
hang while waiting for TEMT. Define this option to avoid it.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
If the pl011 is connected to another device which has hardware
flow-control on, characters are never received by the pl011.
Asserting RTS when flow-control is off will have no effect.
This is in line with how Linux behaves.
Signed-off-by: Joshua Housh <joshua.housh@calxeda.com>
Tested-by: Marek Vasut <marex@denx.de>
On kzm9g board (rmobile SoC), autoboot fails if serial console cable is not
connected. When serial cable is not connected, serial error occurs and
some garbage comes in data register.
sh_serial_tstc() in serial_sh.c does not check error status and misunderstand
there is some input data. It is the reason that autoboot fails.
This patch adds checking error status in sh_serial_tstc().
This patch is based on v2013.01-rc1 tag of u-boot master git.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
TEMT is set when the transmitter is totally empty and all output has
finished.
This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
CONFIG_NS16550_MIN_FUNCTIONS is used by small SPLs to gain access to basic
ns16550 output code without pulling in things not needed by the SPL.
This previously only worked with non-MULTI configs. Recently MULTI was
made mandatory, and MIN_FUNCTIONS fails like this:
drivers/serial/libserial.o: In function `calc_divisor.clone.0':
serial_ns16550.c:(.text.calc_divisor.clone.0+0x24): undefined reference to `get_bus_freq'
drivers/serial/libserial.o: In function `_serial_getc':
(.text._serial_getc+0x30): undefined reference to `NS16550_getc'
drivers/serial/libserial.o: In function `_serial_tstc':
(.text._serial_tstc+0x30): undefined reference to `NS16550_tstc'
drivers/serial/libserial.o: In function `_serial_setbrg':
(.text._serial_setbrg+0x3c): undefined reference to `NS16550_reinit'
make[1]: *** [/tmp/u-boot/spl/u-boot-spl] Error 1
make: *** [/tmp/u-boot/spl/u-boot-spl.bin] Error 2
With MIN_FUNCTIONS we don't need anything from this file, so don't build
it. The conditional needs to be in the file itself rather than the
makefile, because the config symbols are only imported to the makefiles
once, not separately for the SPL phase of the build.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch is fixing the following errors
s3c64xx.c:175: error: variable 's3c64xx_serial_drv' has initializer but incomplete type
s3c64xx.c:176: error: unknown field 'name' specified in initializer
s3c64xx.c:176: warning: excess elements in struct initializer
s3c64xx.c:176: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:177: error: unknown field 'start' specified in initializer
s3c64xx.c:177: warning: excess elements in struct initializer
s3c64xx.c:177: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:178: error: unknown field 'stop' specified in initializer
s3c64xx.c:178: warning: excess elements in struct initializer
s3c64xx.c:178: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:179: error: unknown field 'setbrg' specified in initializer
s3c64xx.c:179: warning: excess elements in struct initializer
s3c64xx.c:179: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:180: error: unknown field 'putc' specified in initializer
s3c64xx.c:180: warning: excess elements in struct initializer
s3c64xx.c:180: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:181: error: unknown field 'puts' specified in initializer
s3c64xx.c:181: warning: excess elements in struct initializer
s3c64xx.c:181: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:182: error: unknown field 'getc' specified in initializer
s3c64xx.c:182: warning: excess elements in struct initializer
s3c64xx.c:182: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:183: error: unknown field 'tstc' specified in initializer
s3c64xx.c:183: warning: excess elements in struct initializer
s3c64xx.c:183: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c: In function 's3c64xx_serial_initialize':
s3c64xx.c:188: warning: implicit declaration of function 'serial_register'
s3c64xx.c: At top level:
s3c64xx.c:191: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'struct'
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
serial_ns16550.c:222:1: warning: symbol 'eserial1_init' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_setbrg' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_getc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_tstc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_putc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_puts' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_init' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_setbrg' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_getc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_tstc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_putc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_puts' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_init' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_setbrg' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_getc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_tstc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_putc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_puts' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_init' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_setbrg' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_getc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_tstc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_putc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_puts' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The following commit introduces some build failures for ColdFire
platform.
commit abaef69fbe
Author: Marek Vasut <marex@denx.de>
Date: Thu Sep 13 16:51:38 2012 +0200
Add the missed header files.
Sign-off-by: Alison Wang <b18965@freescale.com>
Add kerneldoc annotations into serial core.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reorder the get_current() function to make it a bit more readable.
The code does not grow and there is minor change in the code logic,
where dev != NULL is now checked in any case.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reorder serial_assign() function to get rid of the extra level of
indentation. Also, adjust the return value to be -EINVAL instead of
positive one to be more consistent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
U-Boot contains a lot of duplicit implementations of serial_puts()
call which just pipes single characters into the port in loop. Implement
function that does this behavior into common code, so others can make
easy use of it.
This function is called default_serial_puts() and it's sole purpose
is to call putc() in loop on the whole string passed to it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Enhance the manual relocation of drivers operations structure by
checking if the entries are NULL and increment them only if they
are not. This allows for setting any entry to NULL and it will
survive the manual relocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Compile drivers/serial/serial.c by default both into SPL and into
non-SPL builds, since CONFIG_SERIAL_MULTI is now the default state.
Also having common/serial.c in by default now, it's pointless to keep
-DCONFIG_SERIAL_MULTI in CPPFLAGS any longer, so remove it as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Enable CONFIG_SERIAL_MULTI for all builds of U-Boot. That includes
both SPL builds and non-SPL builds, everything. To avoid poluting
this patch with removal of ifdef-endif constructions containing
CONFIG_SERIAL_MULTI, the CONFIG_SERIAL_MULTI is temporarily added
into CPPFLAGS in config.mk . This will be again removed in following
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the common/serial.c into driver/serial/, since this file
provides serial multiplexing functions and it is imperative to
be linked with libserial.o instead of libcommon.o.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
This serial driver had wrong name of the source file for some time
now. The name of the driver was serial.c instead of any more logical
and fitting name. Thus, rename the driver source file to serial_ns16550.c
and be done with it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Michal Simek <monstr@monstr.eu>
Having both USBTTY and CONFIG_SERIAL_MULTI enabled in SPL, the
usbtty.c file is protected in Makefile to not be compiled into
the SPL. Yet, the ns16550 serial driver does not contain such
protection. Add it to avoid missing symbol error.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sh serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sh driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Phil Edworthy <PHIL.EDWORTHY@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sa1100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sa1100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into s3c44b0 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c44b0 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into pl01x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the pl01x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Mathieu J. Poirier <mathieu.poirier@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Implement support for CONFIG_SERIAL_MULTI into netarm serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the netarm driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into mxc serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the mxc driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into max3100 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the max3100 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into lpc2292 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc2292 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into lh7a40x serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lh7a40x driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into ks8695 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ks8695 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into ixp serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ixp driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michael Schwingen <michael@schwingen.org>
Implement support for CONFIG_SERIAL_MULTI into imx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the imx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
Implement support for CONFIG_SERIAL_MULTI into clps7111 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the clps7111 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into sandbox serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the sandbox driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Implement support for CONFIG_SERIAL_MULTI into s3c64xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c64xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Implement support for CONFIG_SERIAL_MULTI into s3c4510b serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the s3c4510b driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into OpenCores serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the OpenCores driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott McNutt <smcnutt@psyent.com>
Implement support for CONFIG_SERIAL_MULTI into ns9750 serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the ns9750 driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement support for CONFIG_SERIAL_MULTI into MCF serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the MCF driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: TsiChung Liew <tsicliew@gmail.com>
Implement support for CONFIG_SERIAL_MULTI into lpc32xx serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the lpc32xx driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Implement support for CONFIG_SERIAL_MULTI into atmel serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the atmel driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Xu, Hong <Hong.Xu@atmel.com>
Implement support for CONFIG_SERIAL_MULTI into altera serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Scott McNutt <smcnutt@psyent.com>
Implement support for CONFIG_SERIAL_MULTI into altera_jtag serial driver.
This driver was so far only usable directly, but this patch also adds
support for the multi method. This allows using more than one serial
driver alongside the altera_jtag driver. Also, add a weak implementation
of default_serial_console() returning this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Chou <thomas@wytron.com.tw>
Move the registration of eserialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented ns16550_serial_initialize() function, which is
implemented inside of the ns16550 serial driver allows encapsulation
of eserialN_device within the ns16550 serial driver itself.
Also, remove the exports of eserialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the ns16550 serial driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of xuartlite_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented xuartlite_serial_initialize() function, which is
implemented inside of the serial_xuartlite driver allows encapsulation
of xuartlite_serialN_device within the serial_xuartlite driver itself.
Also, remove the exports of xuartlite_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_xuartlite driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Move the registration of zynq_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented zynq_serial_initialize() function, which is
implemented inside of the serial_zynq driver allows encapsulation
of zynq_serialN_device within the serial_zynq driver itself.
Also, remove the exports of zynq_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_zynq driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Tom Rini <trini@ti.com>
Move the registration of s5p_serialN_device ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s5p_serial_initialize() function, which is
implemented inside of the serial_s5p driver allows encapsulation
of s5p_serialN_device within the serial_s5p driver itself.
Also, remove the exports of s5p_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s5p driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Move the registration of serial_XXuart ports from default
serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented pxa_serial_initialize() function, which is
implemented inside of the serial_pxa driver allows encapsulation
of serial_XXuart within the serial_pxa driver itself.
Also, remove the exports of serial_XXuart from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_pxa driver and
the default console is picked by CONFIG_CONS_IDX macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the registration of s3c24xx_serialN_device ports from
default serial_initialize() into driver specific function called from
serial_initialize(). This slims down the serial_initialize() call
to a bare tracker of all possible serial port registration routines
in U-Boot.
The newly implemented s3c24xx_serial_initialize() function, which is
implemented inside of the serial_s3c24xx driver allows encapsulation
of s3c24xx_serialN_device within the serial_s3c24xx driver itself.
Also, remove the exports of s3c24xx_serialN_device from include/serial.h
as they are no longer needed. This is simply because the implementation of
default_serial_console() is wrapped into the serial_s3c24xx driver and
the default console is picked by CONFIG_SERIAL<N> macro in config file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: C Nauman <cnauman@diagraph.com>
Make functions that are local-only static, so no hairy symbols
stick out of the serial_pxa driver file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Implement weak default_serial_console() function in serial_pxa
driver, which gets available in case CONFIG_SERIAL_MULTI is
enabled. This will get helpful in subsequent patches, which will
encapsulate PXA's struct serial_device instances in serial_pxa
driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Properly spell out the whole structure member names when an initialized
varible is instantiated from the struct serial_driver. In case the
structure definition for struct serial_driver undergoes reordering,
there will be no impact on variables defined based on this structure.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: C Nauman <cnauman@diagraph.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Michal Simek <monstr@monstr.eu>
Rename .init() to .start() and .uninit() to .stop() in struct
serial_device. This allows aligning struct serial_device with
closer to struct stdio_dev. The real goal here is to allow
these two structures to converge together and eventually make
one to be a superset of the other.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
The driver is used on Xilinx Zynq platform.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Initialize all possible uartlites and return the first
initialized port. For static configuration is initialization
done in userial_ports array.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
* 'agust@denx.de' of git://git.denx.de/u-boot-staging:
tx25: Use generic gpio_* calls
config: Always use GNU ld
tools: add kwboot binary to .gitignore file
fdt: Include arch specific gpio.h instead of asm-generic/gpio.h
serial: CONSOLE macro is not used
Conflicts:
board/karo/tx25/tx25.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
Before reset dbgu transmitter, we just wait TXEMPTY to drain the
transmitter register(Just in case). If not doing this, we may sometimes
see several weird characters from DBGU.
A short delay is also added to make sure the new serial settings are
settled.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
[cherry-picked from u-boot-atmel/old-next]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
also fix NS16550_init() as we need 16x divider
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@gmail.com>
Acked-by: Christian Riesch <christian.riesch@omicron.at>
Tested-by: Christian Riesch <christian.riesch@omicron.at>
Acked-by: Sughosh Ganu <urwithsughosh@gmail.com>
Tested-by: Sughosh Ganu <urwithsughosh@gmail.com>
The serial device of R8A7740 has the same structure as SH7372 of SH, etc.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The serial device of SH73A0 has the same structure as SH7372 of SH, etc.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This is an sh2a device (max 266MHz) with FPU, video display
controller (VDC), 8 serial ports, 4 I2C channels, 3 CAN ports,
SD and on-chip USB.
The RSK2+SH7269 board uses the SH7269 processor. It is often
referred to as just rsk7269.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This change adds an implementation of high-speed UART found on NXP
LPC32X0 SoCs. Such UARTs are enumerated as UART1, UART2 and UART7.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
This patch adds the support for high speed in usb device framework and usbtty
driver. This feature has been kept within a macro CONFIG_USBD_HS, so the board
configuration files have to define this macro to enable high speed support.
Along with that specific peripheral drivers also need to define a function to
let the framework know that the enumeration has happened at high speed.
This function prototype is "int is_usbd_high_speed(void)"
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
The earlier usb device controller driver was specific to spear platforms. This
patch implements the usb device controller driver as a generic controller which
can be reused by other platforms using this peripheral.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Marek Vasut <marex@denx.de>
The generalised calculation of the serial bit rate reg also applies
to sh7264, it was just the clock speed that was set incorrectly.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In 9792987721 Stefan describes a usecase
where the previous behavior of leaving wMaxPacketSize be unaligned
caused fatal problems. The initial fix for this problem was incomplete
however as it showed another cases of non-aligned access that previously
worked implicitly. This switches to making sure that all access of
wMaxPacketSize are done via (get|put)_unaligned.
In order to maintain a level of readability to the code in some cases
we now use a variable for the value of wMaxPacketSize and in others, a
macro.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Remy Bohmer <linux@bohmer.net>
OpenRISC:
Tested-by: Stefan Kristiansson <stefan.kristiansson@saunalahti.fi>
Beagleboard xM, Pandaboard run-tested, s5p_goni build-tested.
Signed-off-by: Tom Rini <trini@ti.com>
On some usb device controllers (pxa) the endpoint configuration must be programmed prior to enable it.
Signed-off-by: Stefan Herbrechtsmeier <sherbrec@cit-ec.uni-bielefeld.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Remy Bohmer <linux@bohmer.net>
This was used by the AVP in early boot but is no longer used. Unless we
plan to enable it somehow it is not needed. In any case we should try
to use the ns16550 driver instead as it has the same code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The serial driver for iMX SOCs is continuosly changed if a
new SOC or not yet used port is used. CONFIG_SYS_<SOC>_<UART Port>
defines were used only to find the base address for the selected UART.
Instead of that, move the base address to the board configuration
file and drop all #ifdef from driver.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Wolfgang Denk <wd@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
CC: Helmut Raiger <helmut.raiger@hale.at>
CC: John Rigby <jcrigby@gmail.com>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
* Cleanup register definitions by introducing new regs-uart.h, compliant with
rest of U-Boot.
* Remove old register definitions from pxa-regs.h
* Convert serial_pxa to new regs-uart.h
* Cleanup serial_pxa
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This allows us to act like a serial device: we get tab chars and CTRL+C
and respond appropriately.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Build pass with following config:
dkb_config
aspenite_config
edminiv2_config
openrd_ultimate_config
sheevaplug_config
mv88f6281gtw_ge_config
rd6281a_config
guruplug_config
km_kirkwood_config
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Do not setup userial_ports array as const because
in uartlite_serial_putc is out_be32 which can't write
to tx_fifo if is const.
Warning log:
serial_xuartlite.c: In function 'uartlite_serial_putc':
serial_xuartlite.c:60: warning: initialization discards qualifiers from pointer target type
serial_xuartlite.c: In function 'uartlite_serial_getc':
serial_xuartlite.c:78: warning: initialization discards qualifiers from pointer target type
serial_xuartlite.c: In function 'uartlite_serial_tstc':
serial_xuartlite.c:87: warning: initialization discards qualifiers from pointer target type
Signed-off-by: Michal Simek <monstr@monstr.eu>
Not draining the FIFO and waiting for the UART to be non-busy
before changing baudrate results in crap characters on the
console, so let's wait for the FIFO to drain and the last
character to be clocked out before we do that.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is a rather subtle build problem where the build time stamp is not
updated for out-of-tree builds if there exists an in-tree build which
has a valid timestamp file. So if you do an in-tree build, then an
out-of-tree build your timestamp will not change.
The correct timestamp_autogenerated.h lives in the object tree, but it
is not always found there. The source still lives in the source tree and
when compiling version.h, it includes timestamp_autogenerated.h. Since
the current directory is always searched first, this will come from the
source tree rather than the object tree if it exists there. This affects
dependency generation also, which means that common/cmd_version.o will not
even be rebuilt if you have ever done an in-tree build.
A similar problem exists with the version file.
This change moves both files into the 'generated' subdir, which is already
used for asm-offsets.h. Then timestamp.h and version.h are updated to
include the files from there.
There are other places where these generated files are included, but I
cannot see why these don't just use the timestamp.h and version.h headers.
So this change also tidies that up.
I have tested this with in- and out-of-tree builds, but not SPL. I have
looked at various other options for fixing this, including sed on the dep
files, -I- and -include flags to gcc, but I don't think they can be made
to work. Comments welcome.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
This uart simply writes to stdout and reads from stdin. We might imagine
instead buffering the data so that a test interface can check output and
inject input.
Signed-off-by: Simon Glass <sjg@chromium.org>
If CONFIG_SYS_NS16550_MEM32 is defined then 32 bit memory
mapped access will be used to read/write the uart registers.
This is especially useful for SoC devices that implement 16550
compatible uarts but that have peripheral access width constraints.
Signed-off-by: Dave Aldridge <fovsoft@gmail.com>
The rsk7264 (also know as rsk2+sh7264) is an SH2A based board
with 64MB NAND flash and 64MB SDRAM. It is very similar to the
rsk7203 board.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The multi serial support has a "ctlr" field which almost no one uses,
but everyone is forced to set to useless strings. So punt it.
Funny enough, the only code that actually reads this field (the mpc8xx
driver) has a typo where it meant to look for the SCC driver. Fix it
while converting the check to use the name field.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Rather than sticking arch/board/driver specific logic in the common
serial code, push it all out to the respective drivers. The serial
drivers declare these funcs weak so that boards can still override
things with their own definition.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Heiko Schocher <hs@denx.de>
CC: Anatolij Gustschin <agust@denx.de>
CC: Tom Rix <Tom.Rix@windriver.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Craig Nauman <cnauman@diagraph.com>
CC: Prafulla Wadaskar <prafulla@marvell.com>
CC: Mahavir Jain <mjain@marvell.com>
Tested-by: Minkyu Kang <mk7.kang@samsung.com>
* 'master' of git://git.denx.de/u-boot-arm:
run arm_pci_init after relocation
IXP42x PCI rewrite
update/fix PDNB3 board
update/fix IXDP425 / IXDPG425 boards
add dvlhost (dLAN 200 AV Wireless G) board
IXP NPE: add support for fixed-speed MII ports
update/fix AcTux4 board
update/fix AcTux3 board
update/fix AcTux2 board
update/fix AcTux1 board
use -ffunction-sections / --gc-sections on IXP42x
support CONFIG_SYS_LDSCRIPT on ARM
fix "depend" target in npe directory
Fix IXP code to work after relocation was added
trigger hardware watchdog in IXP42x serial driver
add support for IXP42x Rev. B1 and newer
add XScale sub architecture (IXP/PXA) to maintainer list
Conflicts:
arch/arm/lib/board.c
Signed-off-by: Wolfgang Denk <wd@denx.de>
The 'trab' board configuration is broken, and there is nobody who is
interested and willing to fix it. Drop it.
This includes support for VFD displays which have always been used by
this board only.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Two new options:
CONFIG_PL011_SERIAL_RLCR
Some vendor versions of PL011 serial ports (e.g. ST-Ericsson U8500)
have separate receive and transmit line control registers. Set
this variable to initialize the extra register.
CONFIG_PL011_SERIAL_FLUSH_ON_INIT
On some platforms (e.g. U8500) U-Boot is loaded by a second stage
boot loader that has already initialized the UART. Define this
variable to flush the UART at init time.
empty fifo on init
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
The serial of ap325rxa has it of two kinds, and the setting of
the clock is different.
Because there was a problem by function to judge serial kind,
this revised it.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
I copied the setting of CPU from Linux kernel and commonized it.
By this, we can communalize a kernel and information.
And added the serial setting of many CPU's.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
ARMADA 100 SoCs has NS16550 compatible UART peripheral
This patch enables the same for ARMADA100 platforms
Signed-off-by: Mahavir Jain <mjain@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
On some processors this ier register configuration is different
for ex. Marvell Armada100
This patch introduce CONFIG_SYS_NS16550_IER macro support to
unconditionally initialize this register.
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Use C structs for registers, and use readl/writel instead of custom
accessors.
Acked-by: Michael Brandt <michael.brandt@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch adds generic support for the Samsung s3c2440 processor.
Global s3c24x0 changes to struct members converting from upper case to
lower case.
Signed-off-by: Craig Nauman <cnauman@diagraph.com>
Cc: kevin.morfitt@fearnside-systems.co.uk
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch is for s5pc210 support.
Due to the resigter of baudrate is changed from slot to value,
add both of them to uart structure.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Call watchdog_reset() upon newline. This is done here in putc
since the environment code uses a single puts() to print the complete
envrironment upon "printenv". So we can't put this watchdog call
in puts().
This is needed for boards with a very short watchdog timeout, like the
lwmon5 with a 100ms timeout. Without this patch this board resets in the
commands with long outputs, like "printenv" or "fdt print".
Note that the image size is not increased with this patch when
CONFIG_HW_WATCHDOG or CONFIG_WATCHDOG are not defined since the compiler
optimizes this additional code away.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix typo in comment.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The pl01x serial driver was lacking the code to switch baudrates from the
command line. Fixed by simply saving the new baudrate and calling
serial_init() again. Also fixed CamelCase variables, I/O accessors and
comment style.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
CONFIG_UART1_CONSOLE was a PPC4xx specific implementation and is now
removed since the move from the 4xx UART driver to the common NS16550
UART driver. Let's remove all references to this define now.
Signed-off-by: Stefan Roese <sr@denx.de>
Because of peripheral devices can select clock sources,
separate the peripheral clocks. (pwm, uart and so on)
It just return the pclk at s5pc1xx SoC,
but s5pc210 SoC must be calculated by own clock register setting.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch is intended to prepare the other S5P SoC. (s5pc210)
If use SoC specific defines then can't share with other SoC.
So, make the accessor functions for access the base address by common way.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
remove below warnings
serial_s5p.c: In function 'serial_getc_dev':
serial_s5p.c:136: warning: dereferencing type-punned pointer will break strict-aliasing rules
serial_s5p.c: In function 'serial_putc_dev':
serial_s5p.c:152: warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The x86 architecture exclusively uses Port-Mapped I/O (inb/outb) to access
the 16550 UARTs. This patch mimics how Linux selects between Memory-Mapped
and Port-Mapped I/O. This allows x86 boards to use CONFIG_SERIAL_MUTLI and
drop the custom serial port driver
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Because of other s5p series SoC will use these serial functions,
modify function's name and structure's name.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds an option to bypass output waiting when there
is no jtag connection. This allows the jtag uart work similar
to a serial uart, ie, boot even without connection.
This option is enabled with CONFIG_ALTERA_JTAG_UART_BYPASS
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Subsequent patch extends mpc512x serial driver to support
multiple PSC ports. The driver will provide an uninit()
function to stop the serial controller and to disable the
controller's clock. Adding uninit() entry to struct serial_device
allows disabling the serial controller after usage of
a stdio serial device.
This patch adds uninit() entry to the struct serial_device
and fixes initialization of this structure in the code
accordingly.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.
Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
The outx/writex macros were using writex(addr, val) rather than
the standard writex(val, addr), resulting in incompatibilty with
architecture independent components. This change set uses standard
parameter order.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The standard Altera UART & JTAG UART as well as the OpenCores
YANU driver are now in individual files in drivers/serial
rather than a single file uner cpu/nios2.
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
I executed 'find . -name "*.[chS]" -perm 755 -exec chmod 644 {} \;'
Signed-off-by: Thomas Weber <swirl@gmx.li>
Add some more: neither Makefile nor config.mk need execute permissions.
Signed-off-by: Wolfgang Denk <wd@denx.de>
ARM926EJS core with MX31 peripherals.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Earlier Version Signed-off-by: Wolfgang Denk <wd@denx.de>
CC: Fred Fan <fanyefeng@gmail.com>
CC: Tom <Tom.Rix@windriver.com>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
ns16550 busyloops waiting for incoming byte causing watchdog to reboot
while waiting for a key press. A call to WATCHDOG_RESET in NS16550_getc
loop fixes it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
SPEAr SoCs contain a synopsys usb device controller.
USB Device IP can work in 2 modes
- DMA mode
- Slave mode
The driver adds support only for slave mode operation of usb
device IP. This driver is used along with standard USBTTY
driver to obtain a tty interface over USB on the host
Signed-off-by: Vipin <vipin.kumar@st.com>
This change adds the usb device support for musb.
Omap3 platform support added at the same level as davinci.
The interface for usbtty to use the musb device support was added.
Verified on omap3 beagle, zoom1 and zoom2.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Because of Frame error, Parity error and Overrun error are occured only receive
operation, need to masking when error checking.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch moves the s3c24x0 header files from include/ to
include/asm-arm/arch-s3c24x0/.
checkpatch.pl showed 2 errors and 3 warnings. The 2 errors were both due
to a non-UTF8 character in David M?ller's name:
ERROR: Invalid UTF-8, patch and commit message should be encoded in UTF-8
#489: FILE: include/asm-arm/arch-s3c24x0/s3c2410.h:3:
+ * David M?ller ELSOFT AG Switzerland. d.mueller@elsoft.ch
As David's name correctly contains a non-UTF8 character I haven't fixed
these errors.
The 3 warnings were all because of the use of 'volatile' in s3c24x0.h:
WARNING: Use of volatile is usually wrong: see Documentation/volatile-considered-harmful.txt
#673: FILE: include/asm-arm/arch-s3c24x0/s3c24x0.h:35:
+typedef volatile u8 S3C24X0_REG8;
+typedef volatile u16 S3C24X0_REG16;
+typedef volatile u32 S3C24X0_REG32;
I'll fix these errors in another patch.
Tested by running MAKEALL for ARM8 targets and ensuring there were no new
errors or warnings.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
fix the following compile warnings
warning: dereferencing type-punned pointer will break strict-aliasing rules
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch re-formats the arm920t s3c24x0 driver files, excluding the nand
driver, in preparation for changes to add support for the Embest SBC2440-II Board.
The changes are as follows:
- re-indent the code using Lindent
- make sure register layouts are defined using a C struct
- replace the upper-case typedef'ed C struct names with lower case
non-typedef'ed ones
- make sure registers are accessed using the proper accessor functions
- run checkpatch.pl and fix any error reports
It assumes the following patch has been applied first:
- [U-Boot][PATCH-ARM] CONFIG_SYS_HZ fix for ARM902T S3C24X0 Boards, 05/09/2009
- patches 1/4 and 2/4 of this series
Tested on an Embest SBC2440-II Board with local u-boot patches as I don't have
any s3c2400 or s3c2410 boards but need this patch applying before I can submit
patches for the SBC2440-II Board. Also, temporarily modified sbc2410x, smdk2400,
smdk2410 and trab configs to use the mtd nand driver (which isn't used by any
board at the moment), ran MAKEALL for all ARM9 targets and no new warnings or
errors were found.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch includes the serial driver for s5pc1xx.
s5pc1xx uart driver needs own register setting and clock configuration.
So, need to special driver.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
As the common code also handles baudrate switching, which the board
specific vct.c driver did not support, this is one of the rare
occassions where deleting code actually adds a feature :)
Signed-off-by: Detlev Zundel <dzu@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
This Patch adds Support for PXA27X UDC.
(Rebased to drivers/usb reorganisation)
Signed-off-by: Vivek Kutal <vivek.kutal@azingo.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
introduce serial_exit for this purpose. Use it only when the rm9200
serial driver is active
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Fix problems introduced in commit
7b5611cdd1 [inka4x0: Add hardware
diagnosis functions for inka4x0] which redefined MSR_RI which is
already used on PowerPC systems.
Also eliminate redundant definitions in ps2mult.h. More cleanup will
be needed for other redundant occurrences though.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Serial driver via the EmbeddedICE macrocell's DCC channel using
co-processor 14.
It does include a timeout to ensure that the system does not
totally freeze when there is nothing connected to read.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error. This option will exclude all functions with exception of
NS16550_putc and NS16550_init. This will be used primarily to save space and
remove unused code from builds in which space is limited.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
V3: Fixed line-wrap problem due to user error in mail!
Added usb_configured() checks in usbtty_puts() and usbtty_putc() to get around a hang
when usb is not connected and the user has set up multi-io (setenv stdout serial,usbtty etc).
Got rid of redundant __attribute__((packed)) directives that were causing warnings from gcc.
Signed-off-by: Atin Malaviya <atin.malaviya@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Applied the patch for baudrate divider value truncation for
serial_init to serial_setbrg as well.
Signed-off-by: Richard Retanubun <RichardRetanubun@RuggedCom.com>
Moved driver vcth.c to vct.c to better reflect the VCT board series.
This driver is now used by the VCT platforms:
vct_premium
vct_platinum
vct_platinumsvc
Signed-off-by: Stefan Roese <sr@denx.de>
The address of SCFSR register is wrong at SH7720/SH7721.
This patch fix this.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Several source files need to be compiled and linked when one or more
config options are selected. To allow for easy selection in the
Makefiles yet to avoild multiple compilation (which costs build time)
and especially multiple linking (which causes errors), we use
"COBJS = $(sort COBJS-y)" which eliminates duplicates.
By courtesy of Detlev Zundel who suggested this approach.
Signed-off-by: Wolfgang Denk <wd@denx.de>
They only differ in the init function.
This also adds the missing watchdog support for the PL011.
Signed-off-by: Andreas Engel <andreas.engel@ericsson.com>
Renesas SH7723 has 5 SCIF, SD, Camera, LCDC and other.
This patch supports CPU register's header file and SCIF serial driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As noted by Harald Welte, HWFLOW support in the S3C64XX serial driver is
broken and currently unused. Remove it.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Round the serial port clock divisor value returned by
calc_divisor()
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Redesign uartlite driver to in_be32 and out_be32 macros
Fix missing header in io.h
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The formula "counter = (u32) (gd->bus_clk / gd->baudrate) / 32"
can generate the wrong divisor due to integer division truncation.
Round the calculated divisor value by adding 1/2 the baudrate
before dividing by the baudrate.
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Round the serial port clock divisor value returned by
calc_divisor().
Signed-off-by: Hugo Villeneuve <hugo.villeneuve@lyrtech.com>
Signed-off-by: John Roberts <john.roberts@pwav.com>
SH7763 has 3 SCIF channels. SCIF0 and 1 are same register constitution,
but only SCIF2 is different. This patch work all SCIF channel.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).
Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Receive FIFO level register is different in SH4A.
Because register is different, cannot occasionally receive data.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SH7780 is CPU of Renesas Technology.
This CPU has
- CPU clock 400MHz
- PCI support
- DDR-SDRAM controller
- etc ...
Signed-off-by: Yusuke Goda <goda.yusuke@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the OMAP5912 Serial Interfaces Reference Guide (see
http://focus.ti.com/lit/ug/spru760c/spru760c.pdf, page 150), the
FIFO_EN enable bit in the FIFO Control Register (FCR) can only be
changed when the baud clock is not running, i. e. when both DLL and
DLH are set to 0.
Thus make sure that DLL and DLH are 0 when writing the FCR.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch fixed wrong SH7720 CPU macro and changed macro that
calculated value of SCBRR register.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SH7710/SH7712 of SH3 CPU are supported.
SH771X is called SH-Ether, and has the Ether controller in CPU.
The driver of Ether is not included in this patch.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The composition of the directory in the drivers/ changed.
I moved SuperH serial driver and marubun PCMCIA driver.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Renamed mcfserial.c to mcfuart.c. Modified Makefile for mcfuart.o from mcfserial.o. Replace immap_5329.h and m5329.h to immap.h
Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>
