This question comes up every now and then with people coming from Linux.
Add some notes about it so we can point to it in the mailing list.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This file is about 10 years old and the updates have not covered
everything that has changed, particularly in the last few years. Update
the information and add mention of the u-boot.dtsi files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix typos.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move this to rST format, largely unchanged to start with. Add an index
for this topic, as well as an empty intro.
Note this patch does not include updates! Is it just a conversion to the
new format. See the next patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchart <xypron.glpk@gmx.de>
Adjust the Latex formatting to match Linux v5.13.1:
* add Latex margins
* reformat the code in doc/conf.py to match Linux
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Now that the spi-nor fix has been made in u-boot/master via:
commit 87e7219f9c ("mtd: spi-nor: Respect flash's hwcaps in spi_nor_adjust_hwcaps()")
enable CONFIG_SPI_FLASH_SMART_HWCAPS on Intel Crown Bay again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update SeaBIOS build instructions using exact command that involves
"make olddefconfig", and mention SeaBIOS release 1.14.0 has been
used for testing.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable SeaBIOS support for any kernel that requires legacy BIOS
services.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make px30 SFC clock configurable
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Odroid Go Advance uses a Rockchip Serial Flash Controller with an
XT25F128B SPI NOR flash chip. This adds support for both. Note that
while both the controller and chip support quad mode, only two lines
are connected to the chip. Changing the pinctrl to bus2 and setting tx
and rx lines to 2 for this reason.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Adds support for XT25F128B used on Odroid Go Advance. Unfortunately
this chip uses a continuation code which I cannot seem to parse, so
there are possibly going to be collisions with chips that use the same
manufacturer/ID.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the serial flash controller to the devicetree for the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for setting the correct pin configuration
for the Rockchip Serial Flash Controller found on the PX30.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for the Rockchip serial flash controller
found on the PX30 SoC. It should work for versions 3-5 of the SFC
IP, however I am only able to test it on v3.
This is adapted from the WIP SPI-MEM driver for the SFC on mainline
Linux. Note that the main difference between this and earlier versions
of the driver is that this one does not support DMA. In testing
the performance difference (performing a dual mode read on a 128Mb
chip) is negligible. DMA, if used, must also be disabled in SPL
mode when using A-TF anyway.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Currently there are a few arm32 rockchip board configs that don't
generate u-boot-rockchip.bin when running make because CONFIG_BINMAN
is not enabled. This patch changes CONFIG_ARCH_ROCKCHIP to also select
CONFIG_BINMAN if CONFIG_SPL and !CONFIG_ARM64.
Example builds that don't generate u-boot-rockchip.bin without this
patch:
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make kylin-rk3036_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make rock_defconfig
make
export ARCH=arm
export CROSS_COMPILE=/usr/bin/arm-linux-gnueabihf-
make tinker-rk3288_defconfig
make
Signed-off-by: Johan Gunnarsson <johan.gunnarsson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the rk3368 DTs and associated bits from 5.14-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the rk3328 DTs and associated bits from 5.14-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the rk3399 DTs and associated bits from 5.14-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
(Remove the conflict content for vmarc-som)
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- Convert GoFlex Home Ethernet and SATA to Driver Model (Tony)
- mvebu: Automatically detect CONFIG_SYS_TCLK (Pavel)
- mvebu: sata_mv: Fix HDD identication during cold start (Tony)
- a37xx: pci: Fix handling PIO config error responses (Pavel)
- Other minor misc changes and board maintainer updates
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEPVPGJshWBf4d9CyLd9zb2sjISdEFAmESPjcACgkQd9zb2sjI
SdFabg/+K/5kH01N6etPpPgNH3DTns3Z7Uv16rawGaFJVj4V2O/Ak2vmhvjJA4df
KvLJL3AVolMOfD4xTABRDyLKt3maCgIYkamdBWBV/xKCTKL7fvvqj8V1U5iUsGKm
Wl2KbbDj+dGNF+IYO9V4T1D/JaRjAUk4YeztFEDaNdP3P1N+01v2FyfkadBL5un3
dqwHb3DMNS2SyjnE3glTAs3g/+3nmrHhAHiVVZQlJHsijuup6f93e8huKQ4v1oFX
xsNzeI9j6jGBvVI6hRsHNLOZzhj8/ZcSntdlL+b4FbY++KzrKidMgVECc486cc8t
IEq/iJHggYhwRtw3EAYblmMVFiQeo07hgSbbSP8mIJWARtqh439tLUyKxW3y/5UT
UlGLHcsSSwv/5NhY8ugGAYeaGGXNpMMc5ISbssnn5FB6VHSox4nRZai5U9jKoyc2
iBNNdyLiLi/Fz9YMWj8SAibajT8bchWu1qW2n85nFb3xWQpXcbjzlglnLY6bX3TQ
1d5ehInNK8deptHNh2eGBsPKOUJ/gDTvEey+6J517hbJ59My96v+dvmbtG7kH9Z8
157KQzjvHH4X9MDW8wYb381TV8kcNi3b16QPP2RKxuK1Zrve0RLPhOAz/YeSkTDN
mavHlaY7JvUXjAct0K5VXHvA9U6DBrvc3eb7KoXL4b4+SHr/4UQ=
=RZ8+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20210810' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- odroid-n2: fix fdtfile suffix for n2-plus
- sei610 & meson64_android cleanups to prepare android 11 boot support
- use Android BCB mechanism for reboot reason instead of HW reboot flag
- Switch meson64_android boot flow to use abootimg for A/B, AVB and DTBO support
Remove the recommended MAC address from the network card.
NanoPi R4S has a EEPROM attached to the 2nd I2C bus (U92), which stores the MAC address.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The host-index-min property is invalid,
so it inherits from the sdmmc definition in dtsi.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Correct the LEDS label name and remove the board type prefix,
which is actually unnecessary here, removes the redefined system status LED pin.
Signed-off-by: Xiaobo Tian <peterwillcn@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This enable hs400 and SDMA support for emmc on evb-rk3399.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This patch adds support for the RK3568 platform to this driver.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock, phy and other configuration, it is convenient to support
new controller. Here a short summary of the changes:
- Add mmc_of_parse to parse dts config.
- Remove OF_PLATDATA related code.
- Reorder header inclusion.
- Add phy ops.
- add ops set_ios_post to modify the parameters of phy when the
clock changes.
- Add execute tuning api for hs200 tuning.
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-radxarock-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. Both rk3xxx.dtsi and rk3188.dtsi have recently
had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3188-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3188
sync the power domain dt-binding header.
This is the state as of v5.12 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In the Linux DT the file rk3xxx.dtsi is shared between
rk3066 and rk3188. This file has recently had some updates.
For a future rk3066 support in U-boot this file must also update.
Move U-boot specific things in a rk3xxx-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3066 and rk3188
sync the clock dt-binding header.
This is the state as of v5.12 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Problem: board_spl_was_booted_from return wrong boot_devices[3] value
/spi@ff1d0000 and same-as-spl dont work properly for SPINOR flash
because arch/arm/mach-rockchip/spl-boot-order.c spl_node_to_boot_device
need parse SPINOR flash node as UCLASS_SPI_FLASH
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000 > board_boot_order: could not map node @618 to a boot-device
/sdhci@fe330000 > /mmc@fe320000
Solution: just change it to /spi@ff1d0000/flash@0
spl-boot-order: same-as-spl > *** BOOT_SOURCE_ID 3 (2:emmc 3:spi 5:sd ...
/spi@ff1d0000/flash@0 > /sdhci@fe330000 > /mmc@fe320000
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Basically all, i.e. rk3036.dtsi, rk3128.dtsi, rk3xxx.dtsi, rk322x.dtsi,
rk3288.dtsi, rk3308-u-boot.dtsi, rk3328-u-boot.dtsi, rk3399-u-boot.dtsi
and px30-u-boot.dtsi Rockchip SoC devicetrees which have mmc indexes
are defining eMMC as mmc0 and sdmmc as mmc1.
This means that the rule to try to boot from the SD card first is ignored,
which as per comment is what we want and is important for distros, which
rely on that.
Fix this by setting the correct mmc index, i.e. first from mmc1 (SD card),
second from mmc0 (eMMC).
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable support to the 2 NOR flashes on the QEMU RISC-V virt machine.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Those embers wrapped with CONFIG_SYS_FLASH_CFI in struct flash_info_t
are unconditionally used in the cfi_flash.c driver.
Drop the #ifdefs in the definition of flash_info_t.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DM version CFI flash driver is in driver/mtd/cfi_flash.c, which
only gets built when FLASH_CFI_DRIVER is on. If CFI_FLASH is on but
FLASH_CFI_DRIVER is not, nothing is enabled at all.
Fix this dependency by selecting FLASH_CFI_DRIVER when CFI_FLASH is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Change maintainer to me. Suriyan no longer has this board and wishes
to see someone maintaining it actively.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Change maintainer to me. Eric no longer has this board and wishes
to see someone maintaining it actively.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
If ddr3_init() fails then DDR was not initialized and we cannot load and
execute U-Boot. We cannot continue, we cannot do anything in this case, so
hang.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Returning fabricated CRS value (0xFFFF0001) by PCIe Root Complex to OS is
allowed only for 4-byte PCI_VENDOR_ID config read request and only when
CRSSVE bit in Root Port PCIe device is enabled. In all other error PCIe
Root Complex must return all-ones.
So implement this logic in pci-aardvark.c driver properly.
aardvark HW does not have Root Port PCIe device and U-Boot does not
implement emulation of this device. So expect that CRSSVE bit is set as
U-Boot can already handle CRS value for PCI_VENDOR_ID config read request.
More callers of pci_bus_read_config() function in U-Boot do not check for
return value, but check readback value. Therefore always fill readback
value in pcie_advk_read_config() function. On error fill all-ones of
correct size as it is required for PCIe Root Complex.
And also correctly propagates error from failed config write request to
return value of pcie_advk_write_config() function. Most U-Boot callers
ignores this return value, but it is a good idea to return correct value
from function.
These issues about return value of failed config read requests, including
special handling of CRS were reported by Lorenzo and Bjorn for Linux kernel
driver pci-aardvark together with quotes from PCIe r4.0 spec, see details:
https://lore.kernel.org/linux-pci/20210624213345.3617-1-pali@kernel.org/t/#u
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
During cold start, with some HDDs, mv_sata_identify() does not populate
the ID words on the 1st ATA ID command. In fact, the first ATA ID
command will only power up the drive, and then the ATA ID command
processing is lost in the process.
Tests with:
- Seagate ST9250320AS 250GB HDD and Seagate ST4000DM004-2CV104 4TB HDD.
- Zyxel NSA310S (Kirkwood 88F6702), Marvell Dreamplug (Kirkwood 88F6281),
Seagate GoFlex Home (Kirkwood 88F6281), Pogoplug V4 (Kirkwood 88F6192).
Observation:
- The Seagate ST9250320AS 250GB took about 3 seconds to spin up.
- The Seagate ST4000DM004-2CV104 4TB took about 8 seconds to spin up.
- mv_sata_identify() did not populate the ID words after the call to
mv_ata_exec_ata_cmd_nondma().
- Attempt to insert a long delay of 30 seconds, ie. mdelay(30_000), after
the call to ata_wait_register() inside mv_ata_exec_ata_cmd_nondma() did
not help with the 4TB drive. The ID words were still empty after that 30s
delay.
Patch Description:
- Added a second ATA ID command in mv_sata_identify(), which will be
executed if the 1st ATA ID command did not return with valid ID words.
- Use the HDD drive capacity in the ID words as a successful indicator of
ATA ID command.
- In the scenario where a box is rebooted, the 1st ATA ID command is always
successful, so there is no extra time wasted.
- In the scenario where a box is cold started, the 1st ATA command is the
power up command. The 2nd ATA ID command alleviates the uncertainty of
how long we have to wait for the ID words to be populated by the SATA
controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Config option CONFIG_SYS_TCLK is set by kw88f6281.h and kw88f6192.h files
to correct SOC/platform value. So do not overwrite it in board config
include files.
Kirkwood 88F6180 and 88F6192 uses 166 MHz TCLK and Kirkwood 88F6281 uses
200 MHz TCLK.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu axp platform always uses fixed 250 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Now every #if-#else case of soc.h file defines CONFIG_SYS_TCLK, so remove
useless default CONFIG_SYS_TCLK value from the end of soc.h file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This mvebu msys platform always uses fixed 200 MHz TCLK. So specify this
CONFIG_SYS_TCLK option in msys section of global file soc.h file instead of
manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 20 in SAR register specifies if TCLK is running at 200 MHz or 166 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Bit 15 in SAR register specifies if TCLK is running at 200 MHz or 250 MHz.
Use this information instead of manual configuration in every board file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
