All other Tegra boards have their alias nodes in the .dts file
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
The pinmux code issues a warning if the caller attempts to disable the
lock bit in a pinmux register, since this is impossible (once it's
locked, the only way to unlock it is to reset the device/pmt controller).
The I2C/DDC/CEC/USB macros expect a lock setting to be passed in,
and the previous setting of DISABLE caused the pinmux table parsing
code to issue the warning. Changing the lock bits in these table
entries to DEFAULT (i.e. don't touch it) fixes this.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
T30 requires specific SDMMC pad programming, and bus power-rail bringup.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Pad config registers exist in APB_MISC_GP space, and control slew
rate, drive strengh, schmidt, high-speed, and low-power modes for
all of the pingroups in Tegra30. This builds off of the pinmux
way of constructing init tables to configure select pads (SDIOCFG,
for instance) during pinmux_init().
Currently, only SDIO1CFG is changed as per the TRM to work with
the SD-card slot on Cardhu.
Thanks to StephenW for the suggestion/original idea.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Use the latest tables & code from our internal U-Boot repo.
The SDMMC3_CD, CLK_LB_IN and CLK_LB_OUT offsets in the pingroup
table were off by a few indices, causing the pinmux init code to
write bad data to the PINMUX_AUX_ regs. This also enabled the lock
bit, which made it impossible to reconfig the pads correctly for
SDMMC3 (SD card on Dalmore) operation. Also fixes SPI_CS2_N,
USB_VBUS_EN0, HDMI_CEC and UART2_RXD/TXD muxes.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This was an older debug/developmental file that got added
accidentally. Not needed/used in any Cardhu build.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Minor edits to clock, apbdma and SPI, make I2C match kernel DT, and add gpio
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
tegra_mmc_init() now parses the DT info for bus width, WP/CD GPIOs, etc.
Tested on Seaboard, fully functional.
Tamonten boards (medcom-wide, plutux, and tec) use a different/new
dtsi file w/common settings.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Linux dts files were used for those boards that didn't already
have sdhci info populated. Tamonten has their own dtsi file with
common sdhci nodes (sourced from Linux).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
dts Makefile has the arch & board include paths added to DTS_CPPFLAGS.
This allows the use of '#include "xyz"' in the dts/dtsi file which
helps the C preprocessor find common dtsi include files.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
T114, like T30, does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
I2C5 is used to designate the controller intended for power
control (PWR_I2C in the schematics). PWR_I2C is set to 400KHz.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This moves the Tegra USB implementation into the drivers/usb/host
directory. Note that this merges the old
/arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code
changes, just moving stuff around.
v2: While at it also move some defines and the usb.h header file to make
usb driver usable for Tegra30.
NOTE: A lot more work is required to properly init the PHYs and PLL_U on
Tegra30, this is just to make porting easier and it does no harm here.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
Signed-off-by: Tom Warren <twarren@nvidia.com>
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add driver for tegra SPI "SLINK" style driver. This controller is
similar to the tegra20 SPI "SFLASH" controller. The difference is
that the SLINK controller is a genernal purpose SPI controller and the
SFLASH controller is special purpose and can only talk to FLASH
devices. In addition there are potentially many instances of an SLINK
controller on tegra and only a single instance of SFLASH. Tegra20 is
currently ths only version of tegra that instantiates an SFLASH
controller.
This driver supports basic PIO mode of operation and is configurable
(CONFIG_OF_CONTROL) to be driven off devicetree bindings. Up to 4
devices per controller may be attached, although typically only a
single chip select line is exposed from tegra per controller so in
reality this is usually limited to 1.
To enable this driver, use CONFIG_TEGRA_SLINK
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add tegra30 SPI SLINK nodes to fdt.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add back host1x node to seaboard dts file. This got dropped during
the tegra fdt sort.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Sort nodes in dts files according the the following rules:
1) Any nodes that already exist in any /include/d file, in the order
they appear in the /include/d file.
2) Any nodes with a reg property, in order of their address.
3) Any nodes without a reg property, alphabetically by node name.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
IRDA is a synonym for UARTB in tegra pinmux, remove all usage of this
synonym and replace with UARTB to disambiguate.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Note that T30 does not have a separate/different DVC (power I2C)
controller like T20 - all 5 I2C controllers are identical, but
DVC_I2C is still used to designate the controller intended for
power control (PWR_I2C in the schematics). On Cardhu, it's used
to access the PMU and EEPROM, as well as the audio codec, temp
sensor, and fuel gauge devices from the OS.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This build is stripped down. It boots to the command prompt.
GPIO is the only peripheral supported. Others TBD.
include/configs/tegra-common.h now holds common config options
for Tegra SoCs.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
This patch adds basic Tegra30 (T30) build support - no specific
board is targeted.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
These are stripped down for bringup, They'll be filled out later
to match-up with the kernel DT contents, and/or as devices are
brought up (mmc, usb, spi, etc.).
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Boards may require a different pinmux setup for DISPALY than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Harmony contains an SD slot with all 8 bits routed. This allows plugging
in an eMMC-chip-in-SD-form-factor.
Seaboard/Springbank/Ventana/AC100 all have an eMMC chip with all 8 bits
hooked up.
Now that the U-Boot eMMC code fully supports 8-bit operation, initialize
those ports as 8-bit instead of 4-bit to improve performance.
Whistler was already registering its ports as 8-bit.
TrimSlice doesn't have any 8-bit ports.
I don't have any Avionic Design boards nor the Colibri board to test with.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Seaboard has a 1366x768 16bpp LCD. The backlight is controlled
by one of the PWMs.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The pulse width/frequency modulation peripheral supports generating
a repeating pulse. It is useful for controlling LCD brightness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard has a GPIO that switches an external mux between Tegra's debug
UART and SPI flash. This is initialized from the SPL so that SPL debug
output can be seen. Simplify the code that does this, and don't actually
request the GPIO in the SPL; just program it. This saves ~4.5K from the
size of the SPL, mostly BSS due to the large gpio_names[] table that is
no longer required. This makes Seaboard's SPL fit within the current max
size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Allen Martin <amartin@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard and Ventana are very similar boards, and so share the seaboard.c
board file. The one difference needed so far is detected at run-time by
calling machine_is_ventana(). This bloats the Ventana build with code
that is never used. Switch to detecting Ventana at compile time to remove
bloat. This shaves ~5K off the SPL size on Ventana, and makes the SPL fit
within the max size.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Port USB1 on Whistler is intended as a device port for USB recovery.
Whistler's DT currently contains an alias for this USB port, even though
Whistler's config doesn't enable multiple USB controllers, so the alias
is unused. Remove the unused alias for consistency for now. Similar,
explicitly disable the port in the device tree too.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The ULPI port is routed onto pins on the mini PCI Express connector. A
standard breakout board may be used to access the port.
* Add required DT entries to configure the ULPI port.
* Setup up the ULPI pinmux in the board code.
* Enable multiple USB controller and ULPI support in the board config.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For Non-Nvidia boards to include newly added features (like emc clock
scaling) it would be necessary to add each feature to their own board
Makefile. This is because currently the top Makefile automaticly includes
these features only for Nvidia boards.
This patch adds a simple Makefile include so all new features become
available for non-Nvidia board vendors.
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Marc Dietrich <marvin24@gmx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The prototypes used in board files were all scattered out, which lead to
code duplication between SPL and normal U-Boot and some prototypes not actually
being used. Consolidate this in a common board header.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename board provided gpio_config_uart() to
gpio_early_init_uart() as it does the same thing as the equally
called function provided by the uart-switch code. This allows
to simply call this function in early board init whether or not
we are building with CONFIG_UART_SWITCH defined.
Also provide a weak symbol for this function, to avoid the
need to provide this function for boards that don't need any
fixup.
This patch supersedes the earlier posted
"tegra: convert gpio_config_uart to weak symbol".
Build tested with MAKEALL -s tegra20
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Convert TEGRA20_ defines to either TEGRA_ or NV_PA_ where appropriate.
Convert tegra20_ source file and function names to tegra_, also.
Upcoming Tegra30 port will use common code/defines/names where possible.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Ventana always pulls in files from the Seaboard directory, so needs to
mkdir $(obj)../seaboard unconditionally. This fixes:
git clean -f -d -x
./MAKEALL ventana
"MAKEALL -s tegra20" passes without this change, because Seaboard
happens to be built before Ventana, and hence the directory has already
been created.
I believe the mkdir is only needed for out-of-tree builds, since the
seaboard directory is part of the source tree. However, since we always
build an SPL for Tegra now, which I believe is effectively an out-of-tree
build, we will always need this at some time. The overhead of just
uncondtionally executing the mkdir is minimal, and simplifies the
Makefile, since we don't need to code up the exact minimal condition to
execute the mkdir.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
None of harmony, seaboard, ventana, whistler directly build files from
../common/, so there's no need to mkdir the obj directory for such files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a flash node to handle the NAND, including memory timings and
page / block size information.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Move warmboot_save_sdram_params() to later in the boot sequence. This
code relies on devicetree to get the address of the memory controller
and with upcoming changes for SPL boot it gets called early in the
boot process when devicetree is not initialized yet.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Don't use timer_init from tegra board.c. This comes out of arm720t
for the SPL build.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This is make naming consistent with the kernel and devicetree and in
preparation of pulling out the common tegra20 code.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards can override this to set up the pinmux correctly to access serial
flash.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Missed some boards after my tegra2_mmc.* -> tegra_mmc.* change, and
one instance of CONFIG_TEGRA2_SPI. MAKEALL -s tegra2 AOK, Seaboard MMC
AOK. Didn't test Tamonten, Paz00 or TrimSlice, as I have none here.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
The new gpio_early_init() function, which does nothing by default, can
be overridden by boards to configure GPIOs at an early stage.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, continue removing/renaming
Tegra2-specific files. No functional changes (yet).
Updated copyrights to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
In anticipation of Tegra3 support, start removing/renaming
Tegra2-specific files. No functional changes (yet).
Also updated copyright to 2012.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a device tree for Ventana; the Seaboard file no longer represents
the HW present on Ventana.
Enable USB on Ventana.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... to enable USB host support, which enables Ethernet support.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Whistler is a highly configurable Tegra evaluation and development board.
This change adds support for the following specific configuration:
E1120 motherboard
E1108 CPU board
E1116 PMU board
The motherboard configuration switches are set as follows:
SW1=0 SW2=0 SW3=5
S1/S2/S3/S4 all on, except S3 7/8 are off.
Other combinations of daugher boards may work to varying degrees, but will
likely require some SW adjustment.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Simon Glass's proposal to fix this on Seaboard was NAK'd, so I
removed his NS16550 references and added a small delay before
SPI/UART muxing. Tested on my Seaboard with large SPI reads/writes
and saw no corruption (crc's matched) and no spurious comm chars.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Jimmy Zhang <jimmzhang@nvidia.com>
Seaboard uses a QUERTY keyboard. We add key codes for this to
enable key scanning to work.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds timings for T20 and T25 Seaboards, using the bindings found here:
http://patchwork.ozlabs.org/patch/132928/
We supply both full speed options for normal running, and half speed options
for testing / development.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Set Seaboard to optimal memory settings based on the SOC in use (T20 or T25).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Tegra core power rail has leakage voltage around 0.2V while system in
suspend mode. The source of the leakage should be coming from PMC power
detect logic for IO rails power detection.
That can be disabled by writing a '0' to PWR_DET_LATCH followed by writing '0'
to PWR_DET (APBDEV_PMC_PWR_DET_0).
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Call the function to put warmboot boot in a suitable place for resume.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This enables I2C on all Nvidia boards including Seaboard and
Harmony.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This adds basic USB support for port 0. The other port is not supported
yet.
Tegra2 (SeaBoard) # usb start
(Re)start USB...
USB: Register 10011 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
scanning bus for storage devices... 1 Storage Device(s) found
Tegra2 (SeaBoard) # ext2load usb 0:3 10000000 /boot/vmlinuz
Loading file "/boot/vmlinuz" from usb device 0:3 (ROOT-A)
2932976 bytes read
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We set up two USB ports, one of which can be host or device.
For some reason the kernel version does enable both ports.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the definition of the oscillator clock frequency and the 32KHz clock.
The latter is provided by a PMIC on I2C which we don't actually use at
present, but we expect this definition to be used in the kernel and want
to keep our .dts the same.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This was taken from commit b48c54e2 at:
git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra.git
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use the new funcmux_select() feature to set up the MMC pin mux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use the new funcmux_select() feature to set up the MMC pin mux.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
As proposed by Mike Frysinger, mkdir can take more than one argument.
Instead of spawning two processes, create both the common and seaboard
directories in one go.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that we can set up the UART in common tegra code, make the boards
use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The clock init is not board specific, so move it into
the cpu code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This call is more of an architecture requirement than a board
one, so move it there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Seaboard changes have removed the need for common/board.o in the
Makefile. Propagate this change to the other Tegra2 builds.
Signed-off-by: Tom Warren <twarren@nvidia.com>
tegra2_mmc_init() is implemented by the Tegra2 MMC driver. Since most of
the Tegra2-based boards will need to call it, this commit exports it in
the new public asm/arch/mmc.h header file to prevent each board from
providing its own prototype.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
On Seaboard the UART and SPI interfere with each other. This causes the UART
to receive spurious zero bytes after SPI transactions and also means that
SPI can corrupt a few output characters when it starts up if they are still
in the UART buffer.
This updates the board to use the SPI/UART switch to avoid the problem.
For now this feature is turned off since it needs changes to the NS16550
UART to operate.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Tegra2 Seaboard has the unfortunate feature that SPI and the console
UART are multiplexed on the same pins. We need to switch between one
and the other during SPI and console activity.
This new file implements a switch and keeps track of which peripheral
owns the pins. It also flips over the controlling GPIO as needed
Since we are adding a second file to board/nvidia/common, we create
a proper Makefile there and remove the direct board.o include from
board/nvidia/seaboard/Makefile
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
UART selection is done with a lot of #ifdefs. This cleans things up
a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Since Ventana is derived from Seaboard and requires seaboard.c to build,
make sure board/nvidia/seaboard is created in the build tree.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Since low-level init is skipped, the instruction cache is never enabled on
Tegra2. This explicitly calls this initialization as soon as the A9 is
initialized.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We want to move away from a special Tegra2 start-up, and just use
arch_cpu_init() instead. However, if we run board_init_f() from boot
we need to build it for ARMv4T, since the Tegra's AVP start-up CPU
does not support ARMv7.
The effect of this is to do the AVP init earlier, and in
arch_cpu_init(), rather that board_early_init_f().
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
... rather than open-coding the register accesses.
However, gpio_request() typically stores the "label" parameter in a global
data structure. This causes problems when called from gpio_config_uart(),
since the code is running before relocation. To solve this, pass a NULL
string to gpio_request(), and modify gpio_request() not to touch the string
if it's NULL.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Ventana is a board which is very similar to Seaboard. Support it by
re-using board/nvidia/seaboard/seaboard.c with minor run-time conditionals.
v5: Makefile: Use cmd_link_o_target, remove unused clean/distclean targets.
v6: Make gpio_config_uart_seaboard() static.
v7: Add MAINTAINERS entry for Ventana. Tom Warren doesn't have Ventana, so
he asked me to add myself for this board.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Pass the GPIO numbers for power and card detect to tegra2_mmc_init(), and
modify that function to perform all required GPIO initialization. This
removes the need for board files to perform these operations.
Move board_mmc_getcd() into tegra2_mmc.c now that the driver knows which
GPIOs to use.
Update affected call-sites in seaboard.c and harmony.c. Note that this
change should make all SD ports work on Harmony, since the required GPIO
setup is now being performed.
v4: Fix prototype of tegra2_mmc_init() in board.h to match driver change.
Remove prototype of gpio_config_mmc() from board.h
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
For Seaboard, this is mostly a cut/paste of board_mmc_init() and
pin_mux_mmc() into seaboard.c; pin_mux_mmc() was modified to add some
missing pinmux_tristate_disable calls for the GPIOs.
For Harmony, those functions were modified to configure SDMMC2 (index 2)
instead of SDMMC3 (index 1), since that's what is present on the board.
However, harmony.c is still missing the required GPIO setup, so neither
port is likely to function correctly yet. This will be fixed in the next
change.
v4: Include board.h to prototype tegra2_mmc_init().
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This centralizes knowledge of MMC clocking into the MMC driver. This also
removes clock setup from the board files, which will simplify later changes
that modify the Harmony board to support the correct set of MMC controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This adds the required GPIO and pinmux configuration to make eMMC / SD work
on Seaboard.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds support for changing pinmux functions of pin groups. This is done
by defining a PMUX_FUNC_... enum which can be used to select the function for
each group using pinmux_set_func(). It is also possible to enable
pullup/pulldown, and the existing tristate functionality is retained.
Also provided is a means of configuring a list of pingroups by providing a
configuration table to pinmux_config_table().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
The pin groupings are better named PINGRP, since on Tegra2 they refer to
multiple pins.
Sorry about this, but better to get it right now when there is only a small
amount of code affected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds most of the clock functions required by board and driver code:
-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control
These functions are plumbed in as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This removes clock_init() and pinmux_init() which are names better suited
to those respective modules. By moving board_init_f() to the bottom of the
file we can remove the need for so many functions in the board.h header file.
The only clock/pinmux/gpio init we need to do prior to relocation is
for the UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Rename CLOCK_PLL_ID to CLOCK_ID which takes account of the fact that the
code now deals with both PLL clocks and source clocks.
This also tidied up the assert() to match the one sent upstream, and fixes
an error in the PWM id.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The out-of-tree build fails because the Makefiles in question depend on
source files of another directory but do not explicitly mkdir that
directory.
As a matter of fact, other Makefiles under board/*/ directory that refer
to source files under another directory explicitly call mkdir.
This patch adds explicit mkdir's to the Makefiles in question, and
verifies that out-of-tree build is working.
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
NVIDIA boards and Samsung SMDK6400 already use a local variant of
CONFIG_MACH_TYPE option.
Switch to use the new common code.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
