Commit graph

60 commits

Author SHA1 Message Date
Tom Rini
be7dbb60c5 Convert CONFIG_SYS_IMMR to Kconfig
This converts the following to Kconfig:
   CONFIG_SYS_IMMR

We do this by consolidating the SYS_IMMR options we have and providing
defaults.

We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 08:41:38 -05:00
Biwen Li
781188097d gpio: mpc8xxx_gpio: Fix for litte endian
Update gpio driver to use same logic for big-endian and little-endian

Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-08 14:01:19 +05:30
Meenakshi Aggarwal
3a187cff7a armv8: lx2162a: Add Soc changes to support LX2162A
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.

LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.

Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-10 13:56:39 +05:30
Razvan Ionut Cirjan
c760095adb net: lx2160a.c: Update to set ECx_PMUX precedence
As per hardware documentation, ECx_PMUX has precedence
over SerDes protocol.
For LX2160/LX2162 if DPMACs 17 and 18 are enabled as SGMII
through SerDes protocol but ECx_PMUX configured them as RGMII,
then the ports will be configured as RGMII and not SGMII.

Signed-off-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-10-23 16:52:09 +05:30
Simon Glass
f09f1ecbe7 Use __ASSEMBLY__ as the assembly macros
Some places use __ASSEMBLER__ instead which does not work since the
Makefile does not define it. Fix them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Yinbo Zhu
316fc6ff76 armv8: ls1028a: define esdhc_status_fixup
This patch is to define esdhc_status_fixup function for ls1028a to disable
SDHC1/SDHC2 status in device tree node if not selected.

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Xiaowei Bao <xiaowei.bao@nxp.com>
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-04-20 13:35:11 +05:30
Kuldeep Singh
0b6c3706ab fsl-lsch3: Add FlexSPI address space in immap_lsch3
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajat Srivastava <rajat.srivastava@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
2019-12-26 16:00:20 +05:30
Ran Wang
0cfa00cdb9 armv8: Add workaround for USB erratum A-050106
USB3.0 Receiver needs to enable fixed equalization
for each of PHY instances in an SOC. This is similar
to erratum A-009007, but this one is for LX2160A,
and the register value is different.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-12-26 16:00:20 +05:30
Laurentiu Tudor
30449aea50 armv8: lx2160a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, sec.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08 11:13:38 +05:30
Laurentiu Tudor
ab04dee542 fsl-layerscape: add missing SATA3 and SATA4 base addresses
LX2160A chips have 4 sata controllers. Add missing base addresses for
SATA3 and SATA4.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-11-08 11:13:38 +05:30
Yinbo Zhu
24cb6f2295 fsl-layerscape: Add fsl_esdhc peripheral clock support
Add esdhc peripheral clock support
for NXP layerscape platforms: LS1046ARDB, LS1043ARDB,
LS1012ARDB, LS1028ARDB, LS1088ARDB, LX2160ARDB

Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2019-09-12 14:00:35 +05:30
Laurentiu Tudor
b249fcba00 armv8: ls1028a: add icid setup for platform devices
Add ICID setup for the platform devices contained on this chip: usb,
sata, sdhc, edma, qdma, gpu, display and sec.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
08f9bc9f43 armv8: fsl-layerscape: add base addresses for several devices
Add CCSR base addresses for ESDHC2, EDMA QDMA, DISPLAY and GPU devices.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Laurentiu Tudor
ef3f364a75 armv8: fsl-layerscape: add missing sec jr base address defines
Add defines for all the SEC job rings base addresses.

Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-08-22 09:07:36 +05:30
Alex Marginean
062d8148f8 arm: ls1028a: define the integrated PCI bus (ECAM)
LS1028A includes an integrated PCI bus with 11 PCI functions residing on
bus 0.  ECAM plus the device register space takes up 256MB of address
space.

Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:57 +05:30
Ran Wang
3458a4198c armv8: ls1028a: enable workaround for USB erratum A-008997
Enable workaround for USB erratum A-008997. Here PCSTXSWINGFULL
registers has been moved to DSCR as compared to other Layerscape SoCs
where it was in SCFG.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-06-19 12:54:56 +05:30
Yuantian Tang
d4ad111dc4 armv8: ls1028a: Add NXP LS1028A SoC support
Ls1028a SoC is based on Layerscape Chassis Generation 3.2
architecture with features:
 2 ARM v8 Cortex-A72 cores, CCI400, SEC, DDR3L/4, LCD, GPU, TSN
 ENETC, 2 USB 3.0, 2 eSDHC, 2 FlexCAN, 2 SPI, SATA, 8 I2C controllers,
 6 LPUARTs, GPIO, SAI, qDMA, eDMA, GIC, TMU etc.

Signed-off-by: Sudhanshu Gupta <sudhanshu.gupta@nxp.com>
Signed-off-by: Rai Harninder <harninder.rai@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22 12:24:24 +05:30
Hou Zhiqiang
059d942283 armv8: lx2160a: add MMU table entries for PCIe
The lx2160a have up to 6 PCIe controllers and have different
address and size of PCIe region.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-05-22 12:24:24 +05:30
Pankaj Bansal
1eba723c72 lx2160aqds : Add support for LX2160AQDS platform
LX2160AQDS is a development board that supports LX2160A
family SoCs. This patch add base support for this board.

Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[PK: Sqaush patch for "secure boot defconfig" & add maintainer]
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
2019-02-19 10:26:44 +05:30
Priyanka Jain
4909b89ec7 armv8: lx2160a: Add LX2160A SoC Support
LX2160A Soc is based on Layerscape Chassis Generation 3.2
architecture with features:
 16 ARM v8 Cortex-A72 cores in 8 cluster, CCN508, SEC,
 2 64-bit DDR4 memory controller, RGMII, 8 I2C controllers,
 3 serdes modules, USB 3.0, SATA, 4 PL011 SBSA UARTs,
 4 TZASC instances, etc.

SoC personalites:
LX2120A is SoC with Twelve 64-bit ARM v8 Cortex-A72 CPUs
LX2080A is SoC with Eight 64-bit ARM v8 Cortex-A72 CPUs

Signed-off-by: Bao Xiaowei <xiaowei.bao@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00
Priyanka Jain
d6fdec211f armv8:fsl-layerscape: Add support for Chassis 3.2
NXP layerscape architecture Chassis 3.2 builds upon chassis3
architecture with changes like DDR Memory map change,
removal of IFC and support of upto 8 I2C controller.

Patch add README.lsch3_2 and the above changes under
macro CONFIG_NXP_LSCH3_2.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:19 -08:00
Rajesh Bhagat
4c41738462 armv8: fsl-layerscape: identify boot source from PORSR register
PORSR register holds the cfg_rcw_src field which can be used
to identify boot source.

Further, it can be used to select the environment location.

Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix multiple checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
2018-12-06 14:37:26 -08:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Rajesh Bhagat
23a12cb3d0 board: common: vid: Add support for LTC3882 voltage regulator chip
Restructures common driver to support LTC3882 voltage regulator
chip.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23 11:19:56 -08:00
Rajesh Bhagat
a1f95ff7d7 armv8: lsch3: Add serdes and DDR voltage setup
Adds SERDES voltage and reset SERDES lanes API and makes
enable/disable DDR controller support 0.9V API common.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2018-01-23 11:18:12 -08:00
Hou Zhiqiang
c4787f4b23 armv8: ls1088a: fix the MMU table for pcie config space
The pcie config space of ls1088a is different from ls2080a.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:07 -07:00
Ran Wang
15d59b5316 armv8: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values.

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
2a8a353958 armv8: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receiver
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
2ab1553f08 armv8: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ashish Kumar
17d066fc5d armv8: fsl-layerscape: Support to add RGMII for ls1088aqds
This patch adds support for RGMII protocol

NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:05 -07:00
Ashish Kumar
6d9b82d085 armv8: ls1088a: Add NXP LS1088A SoC support
LS1088A is compliant with the Layerscape Chassis Generation 3 with
eight ARM v8 Cortex-A53 cores in 2 cluster, CCI-400, one 64-bit DDR4
SDRAM memory controller with ECC, Data path acceleration architecture
2.0 (DPAA2), Ethernet interfaces (SGMIIs, RGMIIs, QSGMIIs, XFIs),
QSPI, IFC, PCIe, SATA, USB, SDXC, DUARTs etc.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:00:13 -07:00
Priyanka Jain
5193405a16 board: freescale: ls2080ardb: Enable SD interface for RevF board
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-05-23 09:12:26 -07:00
Prabhakar Kushwaha
7b45b383fd armv8:fsl-layerscape: Avoid RCWSR28 register hard-coding
SerDes information is not necessary to be present in RCWSR29 register.
It may vary from SoC to SoC.

So Avoid RCWSR28 register hard-coding.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-28 09:09:22 -07:00
Priyanka Jain
29ca713cc1 armv8: fsl-lsch3: Update VID support
VID support in NXP layerscape Chassis-3 (lsch3) compilant SoCs like
LS2088A, LS2080A differs from existing logic.
-VDD voltage array is different
-Registers are different
-VDD calculation logic is different

Add new function adjust_vdd() for LSCH3 compliant SoCs

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-14 08:44:03 -07:00
Priyanka Jain
27f133bbcf armv8: fsl-layerscape: Updates DCFG register map
Based on latest hardware documentation,
update ccsr_gur structure (represents DCFG register map)

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Arpit Goel <arpit.goel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-03-14 08:44:03 -07:00
Hou Zhiqiang
3564208e01 armv8/fsl-lsch3: consolidate the clock system initialization
This patch binds the sys_info->freq_systembus to Platform PLL, and
implements the IPs' clock function individually.

Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:28:09 -08:00
Minghuan Lian
2acfda1292 armv8: ls2080a: Enable PCIe in defconfigs
The patch enables PCIe in ls2080a defconfigs and
removes unused PCIe related macro defines.

Signed-off-by: Minghuan Lian <Minghuan.Lian@nxp.com>
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:27:07 -08:00
Yuan Yao
dd2ad2f131 armv8: QSPI: Add AHB bus 16MB+ size support
The default configuration for QSPI AHB bus can't support 16MB+.
But some flash on NXP layerscape board are more than 16MB.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-12-05 08:32:43 -08:00
Priyanka Jain
f6b96ff665 armv8: lsch3: Use SVR based timer base address detection
Timer controller base address has been changed from
LS2080A SoC (and its personalities) to new SoCs like
LS2088A, LS1088A.

Use SVR based timer base address detection to avoid compile time #ifdef.

Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:31 -08:00
Priyanka Jain
f6a70b3a92 armv8: lsch3: Add generic get_svr() in assembly
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-11-22 11:37:07 -08:00
York Sun
b63a950629 armv8: ls2080a: Remove debug server support
Debug server feature has been dropped from roadmap.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-09-14 14:07:19 -07:00
Alison Wang
79119a4d19 armv8: fsl-layerscape: Add A72 core detection
Add support to detect Cortex-A72 core for printing it out.
The Initiator Version of A72 core should be 0x4.

Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:02:00 -07:00
Rajesh Bhagat
9729dc9565 include: usb: Rename USB controller base address mapping
Remove Soc specific defines and use generic chasis specific defines
for USB controller base address mapping.

Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-07-26 09:01:04 -07:00
Tom Rini
a10a31ec91 Merge branch 'master' of git://git.denx.de/u-boot-usb
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	arch/arm/include/asm/arch-fsl-layerscape/immap_lsch3.h
2016-06-18 23:46:21 -04:00
Sriram Dash
ef53b8c4ce usb: xhci: fsl: Add workaround for USB erratum A008751
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-13 15:16:46 +02:00
Sriram Dash
6fb522dc77 arm64: fsl-layerscape: add get_svr and IS_SVR_REV helper
Adds get_svr and IS_SVR_REV helpers for ARMv8 platforms,
similar to PPC and ARMv7.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
2016-06-13 15:16:38 +02:00
Yuan Yao
453418f2d2 armv8: ls2080aqds: Config QSPI pin mux via FPGA in NAND boot
Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10 13:45:00 -07:00
Yuan Yao
916d9f099e armv8: ls2080aqds: Select QSPI CLK div via SCFG
QSPI module output SCLK divisor value is configured through SCFG.

Signed-off-by: Yuan Yao <yao.yuan@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10 13:44:59 -07:00
Yunhui Cui
a758177f9b armv8/ls2080a: configure PMU's PCTBENR to enable WDT
The SP805-WDT module on LS2080A requires configuration of PMU's
PCTBENR register to enable watchdog counter decrement and reset
signal generation. The watchdog clock needs to be enabled first.

Signed-off-by: Yunhui Cui <yunhui.cui@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-06-10 13:43:12 -07:00
Alex Porosanu
e99d719359 arch/arm: add SEC JR0 offset
Freescale PPC SoCs do not hard-code security engine's Job Ring 0
address, rather a define is used. This patch adds the same
functionality to the ARM based SoCs (i.e. LS1/LS2 and i.MX parts)

Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-05-18 08:51:46 -07:00