Add the DSI clock enable and disable with PCC reset used.
Add the LCD pixel clock calculation and configuration for DCNano
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for F1C100s internal dram controller.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch aims to add header files for the suniv.
The header files included add support for uart, and clocks.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.
Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.
This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.
We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The GPIO and pinctrl drivers need these setters for pin configuration.
Since they are DM drivers, they should not be using hardcoded base
addresses. Factor out variants of the setter functions which take a
pointer to the GPIO bank's MMIO registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The return values of these functions are always zero, and they are
never checked. Since they are not needed, remove them.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
asm/mmu.h include is currently guarded by CONFIG_ADDR_MAP ifdef because
the header is only present on arm and powerpc. In order to remove the
dependency on this header and the associated ifdef, move init_addr_map()
declaration to init.h, since it is only called during the common init
sequence.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add a return value to init_addr_map and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add YCLK enable for HACE, the HW hash engine of
ASPEED AST2600 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
The AST2600 SRAM has been extended to 88KB since A1
chip revision. This patch updates the SRAM size to
offer more space for early stack/heap use.
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
This symbol has been functionally dead for a long time. Remove the last
and recent re-introductions of setting it, and update the whitelist so
it will not be re-introduced again.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Apple M1 SoCs include an S5L UART which is a variant of the S5P
UART. Add support for this variant and enable it by default
on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Stop using the device tree as a source for ad-hoc information.
This reverts commit 2ae7adc659.
Signed-off-by: Michael Walle <michael@walle.cc>
[trini: Also make board/broadcom/bcmns3/ns3.c fail clearly now]
Signed-off-by: Tom Rini <trini@konsulko.com>
fix up ppll init freq.
support tclk_emmc.
add freq (26M) for mmc device.
fix up the sfc clk rate unit error.
Change in V2:
remove change id.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove some config finishing by _ badly added by
scripts/build-whitelist.sh when joker is used in comments.
for example:
doc/uImage.FIT/command_syntax_extensions.txt:
... #ifdef CONFIG_OF_* | ...
cmd/nvedit.c:# error Define one of CONFIG_ENV_IS_IN_{EEPROM| \
FLASH|MMC|FAT|EXT4|\
Remove also configs only used in comments:
- CONFIG_BOOGER in include/linux/kconfig.h
- CONFIG_COMMANDS
- CONFIG_INIT_IGNORE_ERROR
- CONFIG_REG_*
- CONFIG_HOTPLUG : drivers/watchdog/omap_wdt.c:18
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Rather than duplicate the Ethernet MAC address and carveout updating
code for each board, move it to a common location and make it more
reusable.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
-----BEGIN PGP SIGNATURE-----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=S4kl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211012' of https://source.denx.de/u-boot/custodians/u-boot-stm
- Disable ATAGS for STM32 MCU and MPU boards
- Disable bi_boot_params for STM32 MCU and MPU boards
- Update stm32-usbphyc node management
- Convert CONFIG_STM32_FLASH to Kconfig for STM32 MCU boards
- Convert some USB config flags to Kconfig for various boards
- Convert CONFIG_BOOTCOMMAND flag to Kconfig for STM32 F429 board
- Remove specific CONFIG_STV0991 flags
- Remove unused CONFIG_USER_LOWLEVEL_INIT flag
- Add ofdata_to_platdata() callback for stm32_spi driver
- Update for stm32f7_i2c driver
- Remove gpio_hog_probe_all() from STM32 MP1 board
- Fix bind command
Signed-off-by: Tom Rini <trini@konsulko.com>
The bulk of it is Samuel's DM_I2C rework, which removes the nasty I2C
deprecation warnings for most 32-bit boards. It also includes some
smaller refactorings that pave the way for more changes, mostly driven
by needing to support the Allwinner RISC-V SoC later on.
Board wise we gain support for the FriendlyARM NanoPi R1S H5 router
board and official Pinetab support.
Build-tested for all 160 sunxi boards, and boot tested on a A64, A20,
H3, H6, and H616 board. USB, SD card, eMMC, and Ethernet all work there
(where applicable).
The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
DDR, PER, and CORE PLLs.
Calculating the required values and setting the registers accordingly
was taken from the set_mpu_spreadspectrum routine contained in the
arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
SSC enabled, the reference manual explains that there is a restriction
of range of M values. Since the clk_ti_am3_dpll_round_rate() attempts
to select the minimum possible N, the value of M obtained is not
guaranteed to be within the range required. With the new "ti,min-div"
parameter it is possible to increase N and consequently M to satisfy the
constraint imposed by SSC.
Link: https://lore.kernel.org/r/20210606202253.31649-6-dariobin@libero.it
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Since the beginning, all banks have had space for 32 pins, even when
not all pins were implemented. Let's use a single constant for the GPIO
bank size here, like the GPIO driver is already doing.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This clarifies which callers must be updated to complete the DM_GPIO
conversion.
The only remaining caller of name_to_gpio in generic code is inside the
!DM_GPIO block in cmd/gpio.c. DM_GPIO is always selected on sunxi, so
that code cannot be reached. And after this commit, there are only two
remaining implementations of name_to_gpio.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The only caller of this function was the MMC pinmux code, which used it
to parse a string given from a Kconfig symbol. As the Kconfig symbol has
been converted to a Boolean, this function is no longer needed.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Only one board, Yones Toptech BD1078, actually uses a non-default MMC
pinmux. All other uses of these symbols select the default value or an
invalid value. To simplify things, remove support for the unused pinmux
options, and convert the remaining option to a Boolean.
This allows the pinmux to be chosen by the preprocessor, instead of
having the code parse a string at runtime (for a build-time option!).
Not only does this reduce code size, but it also allows this Kconfig
option to be used in a table-driven DM pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The CCU header is only used by the DM drivers, not any platform code.
Its current location adds an artificial dependency on CONFIG_ARM and
ARCH_SUNXI, which will be problematic when adding the CCU driver for
a RISC-V sunxi platform.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Remove the following STV0991 specific configs:
- CONFIG_STV0991 (never used, only defined in CONFIG_SYS_EXTRA_OPTIONS)
- CONFIG_STV0991_HZ (replaced by generic CONFIG_SYS_HZ)
- CONFIG_STV0991_HZ_CLOCK (replaced by generic CONFIG_SYS_HZ_CLOCK)
This patch allows to reduce the file config_whitelist.txt.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
According to 8MM/MN/MP reference manual, their pad registers only have
4 valid DSE values. And DSE2 and DSE4 are different with current
definitions in iomux-v3.h. Fix the issue to align with manual.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last ARCH_MX25 platform, remove those
references as well.
Cc: Matthias Weisser <weisserm@arcor.de>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last armada100 platform, remove that support
as well.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline.
Remove it. As this is the last mx35 platform, remove that support as
well.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Simplify the bootm and the spl code by using the new config
CONFIG_SUPPORT_PASSING_ATAGS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch enables the use of the optimized memset(), memmove() &
memcpy() versions recently added on ARM64.
Please note that these optimized functions are now only enabled for
recent GCC versions (>= 9.4), as earlier GCC versions throw these
errors:
aarch64-linux-ar: warning: arch/arm/lib/memset-arm64.o: unsupported GNU_PROPERTY_TYPE (5) type: 0xc0000000
...
Signed-off-by: Stefan Roese <sr@denx.de>
[trini: Make this default to off as it causes problems on some platforms still]
Signed-off-by: Tom Rini <trini@konsulko.com>
The AT91 RM9200DK board was removed long time ago.
Remove existing references that were not cleaned up.
Fixes: 1c85752258 ("ARM: remove broken "at91rm9200dk" board")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
