Commit graph

112 commits

Author SHA1 Message Date
Alexander Graf
46a346834b PPC: 85xx: Remove IVOR reset
There is no need to set IVORs to anything but their default values,
so let's leave them where they are.

Suggested-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
[York Sun: Add back $(obj)start.S section in mpc8572ds/Makefile]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:45 -07:00
Suresh Gupta
9c641a872a powerpc/usb: Workaround for erratum-A006261
USB spec says that the minimum disconnect threshold should be
	over 525 mV. However, internal USB PHY threshold value is below
	this specified value. Due to this some devices disconnect at
	run-time. Hence, phy settings are tweaked to increased disconnect
	threshold to be above 525mV by using this workaround.

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-03-07 14:52:16 -08:00
York Sun
133fbfa9e6 powerpc/mpc85xx: Add workaround for erratum A006379
Erratum A006379 says CPCHDBCR0 bit field [10:14] has incorrect default
value after POR. The workaround is to set this field before enabling
CPC to 0x1e.

Erratum A006379 applies to
	T4240 rev 1.0
	B4860 rev 1.0, 2.0

Signed-off-by: York Sun <yorksun@freescale.com>
2013-10-16 16:15:17 -07:00
Prabhakar Kushwaha
e982746844 powerpc/mpc85xx:Make L2 cache type independent of CHASSIS2
CHASSIS2 architecture never defines type of L2 cache present in SoC.
 it is dependent upon the core present in the SoC.
 for example,
    - e6500 core has L2 cluster (Kibo)
    - e5500 core has Backside L2 Cache

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2013-10-16 16:13:11 -07:00
Shengzhou Liu
424bf94273 powerpc/sec: Add workaround for SEC A-003571
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 10:47:07 -07:00
Shruti Kanetkar
6b44d9e5b7 powerpcv2: Print hardcoded size like print_size() does
Makes the startup output more consistent

Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 10:38:12 -07:00
Shruti Kanetkar
2f848f97d7 powerpc: Use print_size() where appropriate
Makes the startup output more consistent

Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 10:37:58 -07:00
ramneek mehresh
9dee205d78 fsl/usb: Move USB internal phy definitions to fsl_usb.h
fsl_usb.h file created to share data bewteen usb platform code
and usb ip driver. Internal phy structure definitions moved to
this file

Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-14 10:58:01 -07:00
York Sun
d217a9ad01 powerpc/mpc85xx: Workaround for A-005812
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:40 -07:00
York Sun
cb93071bb6 mpc85xx: Base emulator support
Prepare for emulator support for mpc85xx parts.
Disable DDR training and skip wrlvl_cntl_2 and wrlvl_cntl_3 registers.
These two registers improve stability but not supported by emulator.
Add CONFIG_FSL_TBCLK_EXTRA_DIV for possible adjustment to time base.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:38 -07:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Scott Wood
8212519254 powerpc/mpc85xx: work around erratum A-006593
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".

The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1.  This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:49 -05:00
Liu Gang
c8b281524b powerpc/boot: Change the macro of Boot from SRIO and PCIE master module
Currently, the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" can enable
the master module of Boot from SRIO and PCIE on a platform. But this
is not a silicon feature, it's just a specific booting mode based on
the SRIO and PCIE interfaces. So it's inappropriate to put the macro
into the file arch/powerpc/include/asm/config_mpc85xx.h.

Change the macro "CONFIG_SYS_FSL_SRIO_PCIE_BOOT_MASTER" to
"CONFIG_SRIO_PCIE_BOOT_MASTER", remove them from
arch/powerpc/include/asm/config_mpc85xx.h file, and add those macros
in configuration header file of each board which can support the
master module of Boot from SRIO and PCIE.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:48 -05:00
James Yang
9cd95ac74a Add e6500 L2 replacement policy selection
This is compile-time config.

Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:10 -05:00
James Yang
c416faf84f Enable L2 cache parity/ECC error checking
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-24 16:54:09 -05:00
Roy Zang
3fa75c875c T4/usb: move usb 2.0 utmi dual phy init code to cpu_init.c
This is what we have done for the UTMI PHY on P3041/P5020. Then the PHY
initialization can be reused in kernel without  “usb start” command.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-14 16:13:25 -05:00
Xulei
99d7b0a43d powerpc/85xx: Add workaround for errata USB-14 (enable on P204x/P3041/P50x0)
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.

In formal release document, the errata number should be USB14 instead of USB138.

Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Shengzhou Liu
72bd83cd0a powerpc/t4240: Adding workaround errata A-005871
When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.

This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.

The Workaround is for the T4240 silicon rev 1.0.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:15 -06:00
Prabhakar Kushwaha
db9a807054 powerpc/mpc85xx:Fix Core cluster configuration loop
Different personalities/derivatives of SoC may have reduced cluster. But it is
not necessary for last valid DCFG_CCSR_TP_CLUSTER register to have
DCFG_CCSR_TP_CLUSTER[EOC] bit set to represent "End of Clusters".

EOC bit can still be set in last DCFG_CCSR_TP_CLUSTER register of orignal SoC
which may not be valid for the personality.
So add initiator type check to find valid cluster.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:10 -06:00
York Sun
afbfdf5450 powerpc/mpc85xx: Fix a bug introduced by CONFIG_PPC_SPINTABLE_COMPATIBLE
Fix a bug introduced by this patch
powerpc/mpc85xx: Temporary fix for spin table backward compatibility

Should have checked both CONFIG_PPC_SPINTABLE_COMPATIBLE and CONFIG_MP in
cpu_init.c.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:08 -06:00
York Sun
2a5fcb835f powerpc/mpc85xx: Temporary fix for spin table backward compatibility
Once u-boot sets the spin table to cache-enabled memory, old kernel which
uses cache-inhibit mapping without coherence will not work properly. We
use this temporary fix until kernel has updated its spin table code.
For now this fix is activated by default. To disable this fix for new
kernel, set environmental variable "spin_table_compat=no". After kernel
has updated spin table code, this default shall be changed.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:06 -06:00
Scott Wood
9a511bd6a3 powerpc/mpc85xx: add comma before "already enabled"
Now outputs like this:

L2:    512 KB already enabled, moving to 0xf8f80000

rather than this:

L2:    512 KB already enabledmoving to 0xf8f80000

Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
2012-11-26 15:41:20 -06:00
Kim Phillips
e56143e54f powerpc/mpc85xx: sparse fixes
fsl_corenet_serdes.c:485:6: warning: symbol '__soc_serdes_init' was not declared. Should it be static?
cpu_init.c:185:6: warning: symbol 'invalidate_cpc' was not declared. Should it be static?
bcsr.c:28:27: warning: non-ANSI function declaration of function 'enable_8568mds_duart'
bcsr.c:39:33: warning: non-ANSI function declaration of function 'enable_8568mds_flash_write'
bcsr.c:46:34: warning: non-ANSI function declaration of function 'disable_8568mds_flash_write'
bcsr.c:53:29: warning: non-ANSI function declaration of function 'enable_8568mds_qe_mdio'
bcsr.c:28:33: warning: non-ANSI function declaration of function 'enable_8569mds_flash_write'
bcsr.c:33:34: warning: non-ANSI function declaration of function 'disable_8569mds_flash_write'
bcsr.c:38:28: warning: non-ANSI function declaration of function 'enable_8569mds_qe_uec'
bcsr.c:63:47: warning: non-ANSI function declaration of function 'disable_8569mds_brd_eeprom_write_protect'
ngpixis.c:245:1: error: directive in argument list
ngpixis.c:247:1: error: directive in argument list

Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
2012-11-04 11:00:36 -07:00
Liu Gang
19e4a00965 powerpc/boot: Change the compile macro for SRIO & PCIE boot master module
Currently, the SRIO and PCIE boot master module will be compiled into the
u-boot image if the macro "CONFIG_FSL_CORENET" has been defined. And this
macro has been included by all the corenet architecture platform boards.
But in fact, it's uncertain whether all corenet platform boards support
this feature.

So it may be better to get rid of the macro "CONFIG_FSL_CORENET", and add
a special macro for every board which can support the feature. This
special macro will be defined in the header file
"arch/powerpc/include/asm/config_mpc85xx.h". It will decide if the SRIO
and PCIE boot master module should be compiled into the board u-boot image.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 15:52:46 -05:00
York Sun
6d2b9da19c powerpc/mpc85xx: Enable L2 at the beginning of U-boot for E6500
Using E6500 L1 cache as initram requires L2 cache enabled.
Add l2-cache cluster enabling.

Setup stash id for L1 cache as (coreID) * 2 + 32 + 0
Setup stash id for L2 cache as (cluster) * 2 + 32 + 1
Stash id for L2 is only set for Chassis 2.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:15 -05:00
Zang Roy-R61911
4e0be34a85 P4080/esdhc: make the P4080 ESDHC13 errata workaround conditional
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 03:04:28 -05:00
York Sun
7ac3cc20e0 powerpc/mpc8xxx: Move HWCONFIG_BUFFER_SIZE into config.h
Before proper environment is setup, we extract hwconfig and put it into a
buffer with size HWCONFIG_BUFFER_SIZE. We need to enlarge the buffer to
accommodate longer string. Since this macro is used in multiple files, we
move it into arch/powerpc/include/asm/config.h.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:56 -05:00
Liu Gang
ff65f12699 powerpc/corenet_ds: Get rid of the SRIOBOOT_MASTER build target
Get rid of the SRIOBOOT_MASTER build target, and to support for serving as
a SRIO boot master via environment variable. Set the environment variable
"bootmaster" to "SRIO1" or "SRIO2" using the following command:

		setenv bootmaster SRIO1
		saveenv

The "bootmaster" will enable the function of the SRIO boot master, and
this has the following advantages compared with SRIOBOOT_MASTER build
configuration:
	1. Reduce a build configuration item in boards.cfg file.
	   No longer need to build a special image for master, just use a
	   normal target image and set the "bootmaster" variable.
	2. No longer need to rebuild an image when change the SRIO port for
	   boot from SRIO, just set the corresponding value to "bootmaster"
	   based on the using SRIO port.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:14 -05:00
York Sun
57125f222e powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditional
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.

Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:

fsl_cpu_a011:disable

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:13 -05:00
York Sun
5e23ab0a31 powerpc/mpc85xx: Workaround for erratum CPU_A011
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
48f6a5c348 powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
1e9ea85f7d powerpc/P4080: Check SVR for CPU22 workaround
Workaround for erratum CPU22 applies to P4080 rev 1 and rev 2 only.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
Prabhakar Kushwaha
5344f7a258 powerpc/85xx:Fix MSR[DE] bit in MSR to support debugger
Debugging of e500 and e500v1 processer requires MSR[DE] bit to be set always.
Where MSR = Machine State register

Make sure of MSR[DE] bit is set uniformaly across the different execution
address space i.e. AS0 and AS1.

Signed-off-by: Radu Lazarescu <radu.lazarescu@freescale.com>
Signed-off-by: Catalin Udma <catalin.udma@freescale.com>
Signed-off-by: Marius Grigoras <marius.grigoras@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
2012-07-06 17:30:30 -05:00
Liu Gang
5056c8e068 powerpc/corenet_ds: Slave core in holdoff when boot from SRIO
When boot from SRIO, slave's core can be in holdoff after powered on for
some specific requirements. Master can release the slave's core at the
right time by SRIO interface.

Master needs to:
	1. Set outbound SRIO windows in order to configure slave's registers
	   for the core's releasing.
	2. Check the SRIO port status when release slave core, if no errors,
	   will implement the process of the slave core's releasing.
Slave needs to:
	1. Set all the cores in holdoff by RCW.
	2. Be powered on before master's boot.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:33 -05:00
Liu Gang
5ffa88eca7 powerpc/corenet_ds: Master module for boot from SRIO
For the powerpc processors with SRIO interface, boot location can be configured
from SRIO1 or SRIO2 by RCW. The processor booting from SRIO can do without flash
for u-boot image. The image can be fetched from another processor's memory
space by SRIO link connected between them.

The processor boots from SRIO is slave, the processor boots from normal flash
memory space and can help slave to boot from its memory space is master.
They are different environments and requirements:

master:
	1. NOR flash for its own u-boot image, ucode and ENV space.
	2. Slave's u-boot image in master NOR flash.
	3. Normally boot from local NOR flash.
	4. Configure SRIO switch system if needed.
slave:
	1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
	2. Boot location should be set to SRIO1 or SRIO2 by RCW.
	3. RCW should configure the SerDes, SRIO interfaces correctly.
	4. Slave must be powered on after master's boot.

For the master module, need to finish these processes:
	1. Initialize the SRIO port and address space.
	2. Set inbound SRIO windows covered slave's u-boot image stored in
	   master's NOR flash.
	3. Master's u-boot image should be generated specifically by
	   make xxxx_SRIOBOOT_MASTER_config
	4. Master must boot first, and then slave can be powered on.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
2012-04-24 23:58:32 -05:00
Timur Tabi
f2717b47ea powerpc/85xx: clean up and document the QE/FMAN microcode macros
Several macros are used to identify and locate the microcode binary image
that U-boot needs to upload to the QE or Fman.  Both the QE and the Fman
use the QE Firmware binary format to package their respective microcode data,
which is why the same macros are used for both.  A given SOC will only have
a QE or an Fman, so this is safe.

Unfortunately, the current macro definition and usage has inconsistencies.
For example, CONFIG_SYS_FMAN_FW_ADDR was used to define the address of Fman
firmware in NOR flash, but CONFIG_SYS_QE_FW_IN_NAND contains the address
of NAND.  There's no way to know by looking at a variable how it's supposed
to be used.

In the future, the code which uploads QE firmware and Fman firmware will
be merged.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Timur Tabi
fbc20aab11 powerpc/85xx: always implement the work-around for Erratum SATA_A001
On the P1022/P1013, the work-around for erratum SATA_A001 was implemented
only if U-Boot initializes SATA, but SATA is not initialized by default.  So
move the work-around to the CPU initialization function, so that it's always
executed on the SOCs that need it.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Kumar Gala
e4c9a35d21 arch/powerpc/cpu/mpc85xx/cpu_init.c: Fix GCC 4.6 build warning
Fix:

cpu_init.c: In function 'cpu_init_r':
cpu_init.c:320:7: warning: variable 'l2srbar' set but not used [-Wunused-but-set-variable]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-11 07:48:59 -06:00
Kumar Gala
2b3a1cdd9e powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].

Refer to the erratum LBIU3 of mpc8548.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Ruchika Gupta
7065b7d466 powerpc/p4080: Add support for secure boot flow
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
   (Please note that ISBC expects all these addresses, images to be
    validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
   at 0xcffffffc.

Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
   CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
   (The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
    created by PBL/configuration word within 0 - 3.5G memory range. The
    u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
   PBL/configuration word after switch to AS = 1

Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
Kumar Gala
c916d7c914 powerpc/85xx: Add support for FMan ethernet in Independent mode
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block.  Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman).  However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.

Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely.  This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.

Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.

We add support for the following SoCs:
 * P1023 - 1 Fman, 2x1g
 * P4080 - 2 Fman, each Fman has 4x1g and 1x10g
 * P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g

Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:05 -05:00
Kumar Gala
acf3f8da98 powerpc/85xx: Handle the lack of L2 cache on P2040/P2040E
The P2040/P2040E have no L2 cache.  So we utilize the SVR to determine
if we are one of these devices and skip the L2 init code in cpu_init.c
and release.  For the device tree we skip the updating of the L2 cache
properties but we still update the chain of caches so the CPC/L3 node
can be properly updated.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:38 -05:00
Stephen George
f110fe940c powerpc/85xx: Adding configuration for DCSRCR to enable 32M access
Configuring DCSRCR to define the DCSR space to be 1G instead
of the default 4M. DCSRCR only allows selection of either 4M
or 1G.
Most DCSR registers are within 4M but the Nexus trace buffer
is located at offset 16M within the DCSR.

Configuring the LAW to be 32M to allow access to the Nexus
trace buffer. No TLB modification is required since accessing
the Nexus trace buffer from within u-boot is not required.

Signed-off-by: Stephen George <stephen.george@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-07-29 08:53:37 -05:00
Roy Zang
86221f09fb powerpc/85xx: Enable Internal USB PHY for p2040, p3041, p5010 and p5020
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
Shaohui Xie
2a9fab82b7 powerpc/85xx: Add PBL boot from SPI flash support on P4080DS
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.

Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-10 11:17:55 -05:00
Haiying Wang
a7b1e1b706 powerpc/85xx: load ucode from nand flash before qe_init
In the case the QE's microcode is stored in nand flash, we need to load it from
NAND flash to ddr first then the qe_init can get the ucode correctly.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
f9a33f1c61 powerpc: Add cpu_secondary_init_r to allow for initialization post env setup
We can simplify some cpu/SoC level initialization by moving it to be
after the environment and non-volatile storage is setup as there might
be dependancies on such things in various boot configurations.

For example for FSL SoC's with QE if we boot from NAND we need it setup
to extra the ucode image to initialize the QE.  If we always do this
after environment & non-volatile storage is working we can have the code
be the same regardless of NOR, NAND, SPI, MMC boot.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-04 09:24:41 -05:00
Kumar Gala
868da5936e powerpc/85xx: Add the workaround for erratum CPC-A003 (enable on P4080)
CoreNet Platform Cache single-bit data error scrubbing will cause data
corruption.  Disable the feature to workaround the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
1d2c2a62e3 powerpc/85xx: Add the workaround for erratum CPC-A002 (enable on P4080)
CoreNet Platform Cache single-bit tag error scrubbing will cause tag
corruption.  Disable the feature to workaround the issue.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Roy Zang
ae026ffd1e fsl_esdhc: Add the workaround for erratum ESDHC136 (enable on P4080)
False multi-bit ECC errors will be reported by the eSDHC buffer which
can trigger a reset request.

We disable all ECC error checking on SDHC.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:22 -06:00
Kumar Gala
a09b9b68d4 powerpc/8xxx: Refactor SRIO initialization into common code
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO.  We mimic what we do with PCIe
controllers for SRIO.

We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.

We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.

Introduced the following standard defines for board config.h:

CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available

(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)

[ These mimic what we have for PCI and PCIe controllers ]

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
2011-01-14 01:32:21 -06:00
Kumar Gala
35079aa98c powerpc/85xx: Replace CONFIG_SYS_HAS_SERDES with a weak function
Instead of a #define use a null weak function for fsl_serdes_init

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-14 01:32:18 -06:00
Haiying Wang
888279b5ed powerpc/85xx: do not reloc l2srbar if CONFIG_FLASH_BASE is not defined
This fixes the compiling error for the board  which doesn't have NOR flash
(so CONFIG_FLASH_BASE is not defined)

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-12-01 10:01:14 -06:00
Kim Phillips
680c613a5c powerpc/8xxx: share PIC defines among 85xx and 86xx
fixes breakeage introduced by commit
a37c36f4e7 "powerpc/8xxx: query
feature reporting register for num cores on unknown cpus"

Reported-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-08-19 02:06:13 -05:00
Kumar Gala
fd3c9befa8 powerpc/p4080: Add workaround for erratum CPU22
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:57 -05:00
Kumar Gala
6aba33e939 powerpc/p4080: Add support for CPC(Corenet platform cache) on CoreNet platforms
The CoreNet style platforms can have a L3 cache that fronts the memory
controllers.  Enable that cache as well as add information into the
device tree about it.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-26 13:07:56 -05:00
Kumar Gala
af0250652a powerpc/85xx: Rework MPC8536 SERDES is_serdes_configured support
Move serdes init until after we are in ram so we can keep track of a
global static protocal map for the particular serdes config we are in.
This makes is_serdes_configured() much simplier and not constantly
reading registers to determine if a given device is enabled based on the
protocol.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-21 00:40:16 -05:00
Becky Bruce
f51cdaf191 83xx/85xx/86xx: LBC register cleanup
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers.  Merge
this into a single spot.

To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.

In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.

I have done a successful ppc build all and tested a board or two from
each processor family.

Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-07-16 10:55:09 -05:00
Kumar Gala
f54fe87ace 85xx/fsl-sata: Use is_serdes_configured() to determine if SATA is enabled
On the MPC85xx platform if we have SATA its connected on SERDES.
Determing if SATA is enabled via sata_initialize should not be board
specific and thus we move it out of the MPC8536DS board code.

Additionally, now that we have is_serdes_configured() we can determine
if the given SATA port is enabled and error out if its not in the
driver.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-05-12 04:53:51 -05:00
Lan Chunhe
3f0202ed13 mpc85xx: Add the ability to set LCRR[CLKDIV] to improve R/W speed of flash
Signed-off-by: Lan Chunhe <b25806@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:56 -05:00
Kumar Gala
4db9708b94 85xx: Convert cpu_init_f code to use out_be32 for LBC registers
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-04-26 22:37:55 -05:00
Stefan Roese
a47a12becf Move arch/ppc to arch/powerpc
As discussed on the list, move "arch/ppc" to "arch/powerpc" to
better match the Linux directory structure.

Please note that this patch also changes the "ppc" target in
MAKEALL to "powerpc" to match this new infrastructure. But "ppc"
is kept as an alias for now, to not break compatibility with
scripts using this name.

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Cc: Anatolij Gustschin <agust@denx.de>
2010-04-21 23:42:38 +02:00
Renamed from arch/ppc/cpu/mpc85xx/cpu_init.c (Browse further)