Sync imx8mm.dtsi with linux-next 20231019.
The motivation for doing this sync was a bug when doing "ums 0 mmc 1"
on imx8mm-evk. It worked well for the first time, but after doing
a CTRL+C and launching the ums again, the command did not work.
Adam Ford suggested to sync imx8mm.dtsi with the Linux dts, as there was
a recent USB power domain reorganization there.
After syncing the imx8mm.dtsi with Linux, the ums command works without
problem after a CTRL+C.
Suggested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Currently, the imx8mp_evk uses the non-DM code to initialize the PMIC.
Convert to DM_PMIC, which is the recommended way to access the PMIC.
While at it, fix multi-line comments style.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add the TPM device found on the GW73xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the TPM device found on the GW73xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add Variscite manufacturer to the IMX8MN_VAR_SOM target menu label as
the majority of targets include the manufacturer as part of their menu
description/label and it helps when looking for a particular
manufacturer/board.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The correct compatible string for i.MX93 variant of DWC EQoS MAC is now
"nxp,imx93-dwmac-eqos".
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add a common board_interface_eth_init() called by the DWC MAC driver to
setup the MAC <-> PHY interface according to the PHY mode obtained from
DT.
Remove the board-side configuration in the i.MX93 EVK files.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Move an OEM closing logic to ahab_close() function to be able to use
it directly without calling a u-boot command.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
The interrupt collector macro name for i.MX23 is MXS_ICOLL_BASE,
this is correct and matches the documentation of both i.MX23 and
i.MX28. Align the i.MX28 macro accordingly. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Sync the devicetree files used in the kernel for the imx8mm-phyboard-polis
with the corresponding devicetree files in U-Boot.
Replaced phycore-imx8mm.dts with kernel dts imx8mm-phyboard-polis-rdk.dts
Synced with kernel 6.5.0-rc1 commit
e752a4f9589c (arm64: dts: freescale: imx8mm-phyboard: Add I2C4 pinmuxing)
Signed-off-by: Cem Tenruh <c.tenruh@phytec.de>
Commit 0aea5dda29 ("ARM: dts: imx7d-sdb-u-boot: Fix usdhc1 UHS
operation") did a temporary workaround by addng the usdhc1 fix
inside the -u-boot.dtsi file.
The imx7d-sdb.dts from kernel 6.5-rc1 contains the proper UHS
fix, so sync the devicetree tree and remove the previous fix
from -u-boot.dtsi.
Also, adjust the PMIC node name inside pmic_get() to match
the devicetree update.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Add support for the Polyhex Debix Model A SBC board.
It is an industrial grade single board computer based on
NXP's i.MX 8M Plus.
Currently supported interfaces are:
- Serial console
- Micro SD
- eQOS and FEC Ethernet
imx8mp-debix-model-a.dts is taken from Linux 6.3.
Signed-off-by: Gilles Talis <gilles.talis@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
As requirement of CR side, QSPI Flash usage via RPC driver shall
be disabled and leaving the control of this module to CR side.
Perform DT modification to disable the RPC SPI.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Cong Dang <cong.dang.xn@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Do not modify defconfig, modify the DT instead, this way
the RPC SPI can be enabled without recompiling the U-Boot
itself. Update commit message accordingly.]
Use the phandle reference to &rpc node in arch/arm/dts/r8a779g0.dtsi
and remove properties which are already in arch/arm/dts/r8a779g0.dtsi.
No functional change and no resulting DT change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
To quote the author:
The show_board_info() function was adjusted to weak so that it could be
entirely replaced with a board-specific implementation.
The intended way for boards to provide their own information is via a
sysinfo driver. But currently there is no way to show anything other
than the model name.
This series adds support for showing a few more items, in a way that is
easy for boards to extend.
Since there is already a weak checkboard() function, we don't need to
have two levels of weak function here. So this series drops the weak
attribute from show_board_info()
Existing boards will see a slight change in output, in that the model
name will appear first, before any custom output. If that is a problem,
then the solution is to implement a sysinfo driver for the board.
Boards can use a sysinfo driver if a particular model name is needed.
Update this board to use checkboard() directly, rather than having a
weak function laid on top of a weak function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Enable USB PHY nodes on ASUS Transformers, Grouper, Enadevoru
and LG X3. This is not mandatory since driver will use default
values but preferable for new devices.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Since required drivers were merged, we can safely clean up the
board and switch to DM based driver with device tree support.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Call regulators_enable_boot_on on board init to set all regulators
with boot-on property in device tree. If regulator is not used by
any device in the device tree but is essential for the device to
work a regression will occur.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Instead of duplicating the I2C3 node and adding NVEC specific
properties, reuse the I2C3 node, extend it with NVEC specific properties
and drop properties that are not needed by NVEC. This results in a DTB
that is a bit cleaner and avoids accidentally using I2C3 and NVEC which
would have them fight over the same hardware resources.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Modify spi and usb aliases name.
Add dt-binding for usb phy define and fix usb phy reset error.
Add tpm/otpee and host_intf node.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Draco is a family of 3 boards: thuban, rastaban & etamin. Rename all
targets of the family adding the draco- prefix to increase readibility
and simplify future commits about concerning all boards of the family.
The name draco was initially used for the first target. It's deprecated
since a 2nd target was introduced. Unfortunately the draco target was
copied to the thuban target instead to be renamed. Remove it to save
unnecessary maintenance effort.
Signed-off-by: Enrico Leto <enrico.leto@siemens.com>
Reduce redundancy in code by using templates to generate the A72 boot
binaries (tispl.bin and u-boot.img) as well as R5 boot binary sysfw.itb
(for legacy boot following devices J721E and AM65x).
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Acked-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Manorit Chawdhry <m-chawdhry@ti.com>
Add templates for FIT images used extensively across K3 boards with most
of the code common. This includes the FIT portions of:
- tispl.bin
- u-boot.img
- sysfw.itb (in case of legacy boot flow)
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
While at this enable the DM and TIFS UARTs for programming pinmux
since they are marked reserved by board.dts
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Kernel dts import now provides bootph-all and bootph-pre-ram properties
for the properties we have been overriding so far. Drop the same.
Reviewed-by: Dhruva Gole <d-gole@ti.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
k3-am62* SoC dtsi files now provide the following:
bootph-all: dmss secure_proxy_main dmsc k3_pds k3_clks k3_reset
main_pmx0 main_timer0 mcu_pmx0 wkup_conf chipid
bootph-pre-ram: secure_proxy_sa3 main_esm mcu_esm
Drop these from board r5 and u-boot.dtsi files as these are duplicate in
them now.
Acked-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Sync with kernel v6.7-rc1 and sync up the u-boot dts files accordingly.
Tested-by: Dhruva Gole <d-gole@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
BCDMA can be used at SPL for OSPI boot and mem-to-mem DMA
so add "bootph-all" to BCDMA node.
Suggested-by: Nishanth Menon <nm@ti.com>
Fixes: 9a3f2b6798 ("arm: dts: k3-am625-verdin-wifi-dev-u-boot.dtsi: Fix DMA/Ethernet")
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Change spl_enable_dcache so it also enable icache on SPL
initialization for the main domain part of the boot flow. This
improves bootloader booting time.
Link: https://lore.kernel.org/all/20231109140958.1093235-1-joao.goncalves@toradex.com/
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Tested-by: Nishanth Menon <nm@ti.com>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
BeagleBoard.org BeagleBone AI-64 is an open source hardware single
board computer based on the Texas Instruments TDA4VM SoC featuring
dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x
floating-point VLIW DSPs, 3x dual ARM Cortex-R5 co-processors,
2x 6-core Programmable Real-Time Unit and Industrial Communication
SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB
DDR4, USB3.0 Type-C, 2x USB SS Type-A, miniDisplayPort, 2x 4-lane
CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and
BeagleBone expansion headers.
This board family can be indentified by the BBONEAI-64-B0 in the
at24 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d 00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]
Baseline of the devicetree is from v6.6-rc1
https://beagleboard.org/ai-64https://git.beagleboard.org/beagleboard/beaglebone-ai-64
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move the omap3 beagle to the beagle vendor folder representing
BeagleBoard.org platforms.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
With the upcoming folder separation, there is no further need to depend
on am625-binman.dtsi. Duplicate the existing definitions to u-boot.dtsi
and r5.dts as appropriate.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Commit 5019170970 ("arch: arm: mach-k3: j721e: add support for UDA
FS") introduced basic UDA FS support, however, we can Take approach
similar to commit 0f1c1e8b36 ("arm: mach-k3: am625: Add support for
UDA FS"). While boot partition support with EMMC boot is useful, it is
constrained by the size of boot hardware partition itself.
In the case of K3 devices, tispl images can contain OP-TEE images that
can substantially vary in size and the u-boot image itself can vary over
time as we enable various features.
So use the CSD information in the case of EMMC_BOOT configuration being
enabled to pick boot partition or UDA FS mode operation to pick.
If EMMC_BOOT is disabled, then depend on filesystem configuration to
pick data from UDA.
Signed-off-by: Nishanth Menon <nm@ti.com>
