This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
The EHCI controller has some very specific requirements for the USB 2.0
port test modes, which were not closely followed in the initial test
mode commit. It demands that the host controller is completely shut down
(all ports suspended, Run/Stop bit unset) when activating test mode, and
will not work on an already enumerated port.
This patch fixes that by introducing a new ehci_shutdown() function that
closely follows the procedure listed in EHCI 4.14. Also, when we have
such a function anyway, we might as well also use it in
usb_lowlevel_stop() to make the normal host controller shutdown cleaner.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The 'enable' argument can be better expressed as boolean.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br>
Currently we have the following behavior in ehci_hcd_init()
- Read csmr1 register, clear bit 26 and then set bit 26.
However a little bit later we call set_usb_phy_clk() which clears bit 26, so
let's get rid of the unnecessary code.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Fix the linker error for missing ulpi_reset when ulpi is not defined
in the board config.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
usb_lowlevel_init() allocates a new periodic_list each time it is invoked,
without freeing the original list. Since it is initialized later on in the code,
just reuse the first-allocated list in future invocations of usb_lowlevel_init.
Cc: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Fixes NFS root problems with Beagle (3530 ES1.0) when used with
external USB-ethernet adapter and "USB start" command used within
u-boot.
Soft resetting the UHH module causes instability issues on
all OMAPs so we just avoid it.
See OMAP36xx Errata
i571: USB host EHCI may stall when entering smart-standby mode
i660: USBHOST Configured In Smart-Idle Can Lead To a Deadlock
On OMAP4/5, soft-resetting the UHH module can put it into
Smart-Idle mode and lead to a deadlock.
On OMAP3 this doesn't seem to be the case but still instabilities
are observed on beagle (3530 ES1.0) if soft-reset is used.
e.g. NFS root failures with Linux kernel.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Move the struct ehci_ctrl defition from ehci-hcd.c into ehci.h
so it can be re-used by drivers. In particular, the mv_udc driver
can benefit from this move.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
Tegra30 and Tegra114 are compatible except PLL parameters.
Tested on Tegra30 Cardhu, and Tegra114 Dalmore
platforms. All works well.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Commit 8f62ca6 "usb: ehci: Support interrupt transfers via periodic list"
didn't include any cache management in the new interrupt transfer path.
It also added an extra write to or_asynclistaddr in usb_lowlevel_init(),
without having flushed out the data there.
Add the missing cache management calls, so that the code works again.
This allows the USB keyboard on Tegra's Seaboard/Springbank boards to
work.
Cc: Patrick Georgi <patrick@georgi-clan.de>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds support to both Faraday FUSBH200 and FOTG210,
the differences between Faraday EHCI and standard EHCI are
listed bellow:
1. The PORTSC starts at 0x30 instead of 0x44.
2. The CONFIGFLAG(0x40) is not only un-implemented, and
also has its address space removed.
3. Faraday EHCI is a TDI design, but it doesn't
compatible with the general TDI implementation
found at both U-Boot and Linux.
4. The ISOC descriptors differ from standard EHCI in
several ways. But since U-boot doesn't support ISOC,
we don't have to worry about that.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
There is at least one non-EHCI compliant controller (i.e. Faraday EHCI)
not only leave RESERVED and CONFIGFLAG registers un-implemented
but also has their address spaces removed.
As an result, the PORTSC register of Faraday EHCI always
starts from 0x30 instead of 0x44 in standard EHCI.
So that we'll need a weak-aliased function for abstraction.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
1. The 'index' of ehci_submit_root() is not always > 0.
e.g.
While it gets invoked from usb_get_descriptor(),
the 'index' is always a '0'. (See ch.9 of USB2.0)
2. The PORTSC register is not always required, and thus it
should only report a port error when necessary.
It would cause a port scan failure if the ehci_submit_root()
always gets terminated by a port error.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Marek Vasut <marex@denx.de>
This commit broke USB2 on link (Chromebook Pixel):
020bbcb usb: hub: Power-cycle on root-hub ports
However the root cause seems to be a missing mask and missing 'break'
in ehci-hcd.c. This patch fixes both.
On link, 'usb start' with a USB keyboard and memory stick inserted now
finds both. The keyboard works as expected. Also ext2ls shows a directory
listing from the memory stick.
Signed-off-by: Simon Glass <sjg@chromium.org>
We can use a common global method for calculating minimum of
3 numbers. Put the same in 'common header' and let 'ehci'
use it.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
This patch adds a new 'usb test' command, that will set a port to a USB
2.0 test mode (see USB 2.0 spec 7.1.20). It supports all five test modes
on both downstream hub ports and ordinary device's upstream ports. In
addition, it supports EHCI root hub ports.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Legacy iomux support is no longer needed now that all boards have been converted
to iomux-v3.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Use the ability to have several active EHCI controller on a system
in the PCI EHCI controller implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
The interrupt endpoint handling code stores the buffer pointer in the QH
padding field. We need to make it the size of a pointer to avoid strict
aliasing issue with the compiler.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Interrupt transfers aren't meant to be used from the async list
(the EHCI spec indicates trouble with low/full-speed intr on async).
Build a periodic list instead, and provide an API to make use of it.
Then, use that API from the existing interrupt transfer API.
This provides support for USB keyboards using EHCI.
Use timeouts to ensure we cannot get stuck in the keyboard scanning
if something wrong happens (USB device unplugged or fatal I/O error)
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Enabling the non-dt path for the driver so that
we don't get any build errors for non-dt configuration.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
With current FDT support driver tries to parse device node
twice in ehci_hcd_init() and ehci_hcd_stop(), which shouldn't
happen ideally.
Making provision to store data in a global structure and thereby
passing its pointer when needed.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
On EHCI controller with 64-bit address space support, we must initialize
properly the high word for the PCI bus master accesses.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Instead of hardcoding the PCI IDs on the USB controller, use the PCI
class to detect them.
Ensure the busmaster bit is properly set in the PCI configuration.
Signed-off-by: Simon Glass <sjg@chromium.org>
The ehci_hcd entry points were just calling into the Tegra USB
functions. Now that they are in the same file we can just move over the
implementation.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This moves the Tegra USB implementation into the drivers/usb/host
directory. Note that this merges the old
/arch/arm/cpu/armv7/tegra20/usb.c file into ehci-tegra.c. No code
changes, just moving stuff around.
v2: While at it also move some defines and the usb.h header file to make
usb driver usable for Tegra30.
NOTE: A lot more work is required to properly init the PHYs and PLL_U on
Tegra30, this is just to make porting easier and it does no harm here.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rework ehci-mxs so it supports both ports on MX28. It was necessary
to wrap the per-port configuration into struct ehci_mxs_port and pull
out the clock configuration function.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
The ehci-mxs driver included the register definitions directly.
Use imx-regs.h instead since it contains proper handling of the
differences between mx23 and mx28.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
Including header for pads is not needed and breaks board
after renaming pin definitions.
Series-to: u-boot
Series-cc: marex@denx.de,fabio.estevam@freescale.com,eric.nelson@boundarydevices.com
Signed-off-by: Stefano Babic <sbabic@denx.de>
Adding fdt support to ehci-exynos in order to parse
register base addresses from the device node.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
By commit c7e3b2b5, this was chanded to support multiple controllers.
But this has missing of parenthesis. This commit fix it.
-----
r8a66597-hcd.c: In function ‘usb_lowlevel_init’:
r8a66597-hcd.c:911:52: error: expected declaration specifiers before ‘)’
token
r8a66597-hcd.c:935:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or‘__attribute__’ before ‘{’ token
r8a66597-hcd.c:939:1: error: expected ‘{’ at end of input
-----
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Lucas Stach <dev@lynxeye.de>
Some variables are initialized with a value defined by macro.
This was changed to use the macro directly. And the variable not to
use deleted it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Linux usb/ch9.h seems to have all the same information (and more)
as usbdescriptors.h so use the former instead of the later one.
As a consequense of this change USB_SPEED_* values don't correspond
directly to EHCI speed encoding anymore, I've added necessary
recoding in EHCI driver. Also there is no point to put speed into
pipe anymore so it's removed and a bunch of host drivers fixed to
look at usb_device->speed instead.
Old usbdescriptors.h included is not removed as it seems to be
used by old USB device code.
This makes usb.h and usbdevice.h incompatible. Fortunately the
only place that tries to include both are the old MUSB code and
it needs usb.h only for USB_DMA_MINALIGN used in aligned attribute
on musb_regs structure but this attribute seems to be unneeded
(old MUSB code doesn't support any DMA at all).
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Eric Bénard <eric@eukrea.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
The correct bit for H1_PM is 16, not 8, which is the DP pull-up impedance
selection bit.
This issue has been reported by Michael Burkey <mdburkey@gmail.com> and fixed by
Christoph Fritz <chf.fritz@googlemail.com> on Linux, from which these #define-s
had been copied.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
A custom board_ehci_hcd_init() may be unneeded, so add a weak default
implementation doing nothing.
By the way, use simple __weak from linux/compiler.h for
board_ehci_hcd_postinit() instead of weak alias with full attribute.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Some MXC SoCs like the i.MX35 have hosts located at unusual offsets, so prepare
to the introduction of i.MX35 support by defining the ehci-mxc hosts offsets at
SoC level.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Make EHCI power and overcurrent polarities configurable. If not set, these new
configurartions keep the default register values so that existing board files
do not have to be changed.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The i.MX53 has MXC_H*_UCTRL_H*_OC_DIS_BIT bits to disable the oc pin.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The MXC_*_UCTRL_*PM_BIT bits are available only on i.MX51.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_UCTRL_OPM_BIT disables (masks) the power/oc pins if set, like
MXC_H1_UCTRL_H1PM_BIT and MXC_H2_UCTRL_H2PM_BIT, not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
MXC_OTG_PHYCTRL_OC_DIS_BIT disables the oc pin if set, like MXC_H1_OC_DIS_BIT,
not the opposite.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Clean up ehci-mxc:
- Remove useless #if's.
- Fix identation.
- Issue a #error if used with an unsupported platform.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
when missing USB PHY clock, u-boot will hang during USB
initialization when issuing "usb start". We should check
USBGP[PHY_CLK_VALID] bit to avoid CPU hanging in this case.
Due to controller issue of PHY_CLK_VALID in ULPI mode, we set
USB_EN before checking PHY_CLK_VALID, otherwise PHY_CLK_VALID
doesn't work.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: David Müller <d.mueller@elsoft.ch>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
The i.MX51 has a single USB PHY clock, while the i.MX53 has two. These 3 clocks
have different clock gate control bit-fields.
The existing code was correct only for i.MX53, so this patch fixes the i.MX51
use case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Jana Rapava <fermata7@gmail.com>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Kill off ehci-core.h
It was used to specify some static controller data. To support more than
one controller being active at any time we have to carry the controller
data ourselfes. Change the ehci interface accordingly.
NOTE: OMAP implemented the ehci stuff a bit backwards and should be fixed
to do the same thing as other platforms. But the change for now is at least
compile clean.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Carry an index in the lowlevel usb functions to make specify the
respective usb controller.
Also pass through an controller struct from lowlevel_init to the
creation of the root usb device of this controller.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.
Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.
v2: fix typo found by Thomas Langer
v3: rebased on top of u-boot-usb/master
Signed-off-by: Lucas Stach <dev@lynxeye.de>
* 'master' of git://git.denx.de/u-boot-usb:
MUSB driver: Timeout is never detected as the while loop does not end
usb: fix ulpi_set_vbus prototype
pxa25x: Add UDC registers definitions
USB: Fix strict aliasing in ohci-hcd
usb: Optimize USB storage read/write
ehci: Optimize qTD allocations
usb_stor_BBB_transport: Do not delay when not required
usb_storage: Remove EHCI constraints
usb_storage: Restore non-EHCI support
ehci-hcd: Boost transfer speed
ehci: cosmetic: Define used constants
ehci: Fail for multi-transaction interrupt transfers
arm:trats: Enable g_dnl composite USB gadget with embedded DFU function on TRATS
arm:trats: Support for USB UDC driver at TRATS board.
dfu:cmd: Support for DFU u-boot command
dfu: MMC specific routines for DFU operation
dfu: DFU backend implementation
dfu:usb: DFU USB function (f_dfu) support for g_dnl composite gadget
dfu:usb: Support for g_dnl composite download gadget.
ehci: cosmetic: Define the number of qt_buffers
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit 5f6aa03fda
USB: Fix complaints about strict aliasing in OHCI-HCD
tried to fix this, but gcc4.4 still complains. So, this
patch basically reverts the above and does a simpler fix.
also, the above commit incorrectly changed
/* corresponds to data_buf[4-7] */
datab [1] = 0;
to
/* corresponds to databuf.u8[4-7] */
databuf.u8[1] = 0;
This patch also fixes that.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Relax the qTD transfer alignment constraints in order to need less qTDs for
buffers that are aligned to 512 bytes but not to pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
This patch takes advantage of the hardware EHCI qTD queuing mechanism to avoid
software and transfer splitting overhead so as to make transfers as fast as
possible.
The only drawback is a call to memalign. However, this is fast compared to the
transfer timings, and the heap size to allocate is small, e.g. 128 kiB in the
worst case for a transfer length of 65535 packets of 512 bytes.
Tested on i.MX25, i.MX35 and i.MX51. In my test conditions, the speed gain was
very significant (several times faster), which is really appreciable when
accessing large files.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Make some light cosmetic code cleanup by the way.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Interrupt transfers requiring several transactions are not supported by
submit_int_msg() because bInterval is ignored. This patch returns a failure code
and prints an error message in this case.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Also enable the ohci port on hawkboard. These additions result in an
increased u-boot size -- adjust the same accordingly in the board's
config.
Move the usb header for da8xx platforms under arch-davinci.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
As the register accessing mode is the same for all i.MXS SoCs we ought
to use 'mxs' prefix intead of 'mx28'.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Buffer coming from upper layers should be cacheline aligned/padded
to perform safe cache operations. For now we don't do bounce
buffering so getting unaligned buffer is an upper layer error.
We can't check if the buffer is properly padded with current
interface so just assume it is (consider changing with in the
future). The following changes are done:
1. Remove useless length alignment check. We get actual transfer
length not the size of the underlying buffer so it's perfectly
valid for it to be unaligned.
2. Move flush_dcache_range() out of while loop or it will
flush too much.
3. Don't try to fix buffer address before calling invalidate:
if it's unaligned it's an error anyway so let cache subsystem
cry about that.
4. Fix end buffer address to be cacheline aligned assuming upper
layer reserved enough space. This is potentially dangerous
operation so upper layers should be careful about that.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
The USB spec says that 32 bytes is the minimum required alignment.
However on some platforms we have a larger minimum requirement for cache
coherency. In those cases, use that value rather than the USB spec
minimum. We add a cpp check to <usb.h> to define USB_DMA_MINALIGN and
make use of it in ehci-hcd.c and musb_core.h. We cannot use MAX() here
as we are not allowed to have tests inside of align(...).
Signed-off-by: Tom Rini <trini@ti.com>
[marek.vasut]: introduce some crazy macro voodoo
Signed-off-by: Marek Vasut <marex@denx.de>
[ilya.yanok]: moved external buffer fixes to separate patch,
we use {ALLOC,DEFINE}_ALIGN_BUFFER macros with alignment of USB_DMA_MINALIGN
for qh_list, qh and qtd structures to make sure they are proper aligned
for both controller and cache operations.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
Move or_asynclistaddr programming to ehci_submit_async()
function to make sure queue head is properly programmed
before every transfer. This solves the problem with changing
qh address.
Also remove unneeded qh_list->qh_link reprogramming at the
end of transfer.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This has never been completely sufficient and now happens too late to
paper over the cache coherency problems with the current USB stack.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
* 'master' of git://git.denx.de/u-boot-arm:
tegra: define fdt_load/fdt_high variables
tegra: enable bootz command
tegra: usb: Fix device enumeration problem of USB1
tegra: trimslice: set up serial flash pinmux
tegra: add pin_mux_spi() board initialization function
tegra: add GMC/GMD funcmux entry for SFLASH
tegra: bootcmd: start USB only when needed
tegra: bootcmd enhancements
tegra: add enterrcm command
tegra: enable CONFIG_ENV_VARS_UBOOT_CONFIG
Add env vars describing U-Boot target board
tegra: usb: fix wrong error check
tegra: add ULPI on USB2 funcmux entry
tegra: fix leftover CONFIG_TEGRA2_MMC & _SPI build switches
tegra: Add Tamonten Evaluation Carrier support
tegra: Use SD write-protect GPIO on Tamonten
tegra: Implement gpio_early_init() on Tamonten
tegra: Allow boards to perform early GPIO setup
tegra: plutux: Add device tree support
tegra: medcom: Add device tree support
tegra: Rework Tamonten support
beagle: add eeprom expansion board info for bct brettl4
Signed-off-by: Wolfgang Denk <wd@denx.de>
A known hardware issue of USB1 port where bit 1 (connect status
change) of PORTSC register will be set after issuing Port Reset
(like "usb reset" in u-boot command line).
This will be treated as an error and stops later device enumeration.
Therefore we clear that bit after Port Reset in order to proceed
later device enumeration.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch adds functions to enable/disable the power of USB
host controller for EXYNOS5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Commit 7a101e946cba55e32d3d1265e30456c810046da3 introduced following warning:
---8<---
ehci-atmel.c: In function 'ehci_hcd_init':
ehci-atmel.c:49:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
ehci-atmel.c: In function 'ehci_hcd_stop':
ehci-atmel.c:79:2: warning: suggest parentheses around comparison in operand of '&' [-Wparentheses]
--->8---
This patch fixes it.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Bo Shen <voice.shen@atmel.com>
cc: Marek Vasut <marex@denx.de>
Some Atmel SoC support USB EHCI, add the EHCI driver to support it.
To enable the USB EHCI, add the following configuration options into
board relative configuration file and remove USB OHCI options.
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 2
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
* 'master' of git://git.denx.de/u-boot-usb:
USB: S5P: Add ehci support
usb:udc:samsung Add functions for storing private gadget data in UDC driver
usb:gadget:composite: Support for composite at gadget.h
usb:gadget:composite USB composite gadget support
usb:udc:samsung:cleanup Replace DEBUG_* macros with debug_cond() calls
usb:udc: Remove duplicated USB definitions from include/linux/usb/ch9.h file
USB: Document the QH and qTD antics in EHCI-HCD
USB: Drop cache flush bloat in EHCI-HCD
USB: Drop ehci_alloc/ehci_free in ehci-hcd
USB: Align buffers at cacheline
usb: use noinline define
The construction of QH and qTD lists in ehci_submit_async() call is cryptic
business, add at least a bit of comments so if someone is reading it, he can at
least reference the intel ehci manual (ehci-r10.pdf).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Discard the creepy cache flushing mechanisms in ehci-hcd.c and replace them with
more straightforward flushing. In the new approach, the flushing takes place
directly in ehci_submit_async() call instead of going through the QH list and
flushing all members and buffers. This discards a lot of weird bit operations
on the members of QH and qTD structures.
NOTE: Certainly, this flushes even qTDs which are possibly unused in some
transactions, though the overhead of the previous code was much higher than is
the overhead of flushing two more cache lines (which most probably aren't even
cached).
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
These two functions were called only from ehci_submit_async(), therefore
dissolve them as part of ehci_submit_async() to get rid of all those static
variables.
Signed-off-by: Marek Vasut <marex@denx.de>
The reference manual of i.MX25 (nor i.MX31) does not define such
register. This seems to access read only UH2_CAPLENGTH register (if
CONFIG_MXC_USB_PORT is zero).
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
The USB controller in i.MX25 has a PORTSCx registers which should be
set. In this regard it is similar to the controller in i.MX31. As this
file is compiled only with i.MX25 and -31, #ifdef check can be removed.
Signed-off-by: Timo Ketola <timo@exertus.fi>
Acked-by: Stefano Babic <sbabic@denx.de>
To get USB working again on the i.MX6, this patch fixes a bug introduced
with commit 522b2a0 "Add proper IO accessors for mx6 usb registers.".
At that occasion, I also added the missing __iomem directive.
Cc: Marek Vasut <marex@denx.de>
CC: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
This is just a patch for the problem reported here:
http://lists.denx.de/pipermail/u-boot/2012-February/117580.html originally reported by Igor.
"Looks like this is copy paste error from my side,(for port2/3 it should have been bypass
for port2/3 rather its port1 set in bypass mode)"
I only submit the patch since it is missing in 2012.04-rc3 while the twister board
depends on it. Maybe it is already somewhere in the reposistory, but I cannot find it.
note: the twister boards still needs an additional `usb reset`, don't know why.
U-Boot 2012.04-rc3-dirty (Apr 19 2012 - 21:38:38)
AM35XX-GP ES1.0, CPU-OPP2, L3-165MHz, Max CPU Clock 600 Mhz
TAM3517 TWISTER Board + LPDDR/NAND
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: OMAP SD/MMC: 0
In: serial
Out: serial
Err: serial
Die ID #746c0000000000000155dc1405011024
Net: DaVinci-EMAC, smc911x-0
Hit any key to stop autoboot: 0
twister => usb start
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
twister => usb reset
(Re)start USB...
USB: Register 1313 NbrPorts 3
USB EHCI 1.00
scanning bus for devices... 1 USB Device(s) found
scanning bus for storage devices... 0 Storage Device(s) found
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Acked-by: Govindraj.R <govindraj.raja <at> ti.com>
Acked-by: Tom Rini <trini@ti.com>
This adds basic support for the Tegra2 USB controller. Board files should
call board_usb_init() to set things up.
Configuration is performed through the FDT, with aliases used to set the
order of the ports, like this fragment:
aliases {
/* This defines the order of our USB ports */
usb0 = "/usb@0xc5008000";
usb1 = "/usb@0xc5000000";
};
drivers/usb/host files ONLY: Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
CONFIG_USB_EHCI_TXFIFO_THRESH enables setting of the txfilltuning
field in the EHCI controller on reset.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add proper IO accessors for mx6 usb registers.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Jason Liu <r64343@freescale.com>
This patch renames mx28_register to mx28_register_32 in order to
prepare for the introduction of an 8-bit register, mx28_register_8.
Signed-off-by: Robert Delien <robert@delien.nl>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
Common code has a mdelay() func, so use that instead of the usb-specific
wait_ms() func. This also fixes the build errors:
ohci-hcd.c: In function 'submit_common_msg':
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1519:9: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1816:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1827:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1844:10: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1563:11: sorry, unimplemented: called from here
/usr/local/src/u-boot/blackfin/include/usb.h:202:44: sorry, unimplemented: inlining failed in call to 'wait_ms': function body not available
ohci-hcd.c:1583:9: sorry, unimplemented: called from here
make[1]: *** [ohci-hcd.o] Error 1
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Marek Vasut <marex@denx.de>
This moves keyboard polling logic from USB HCD drivers into USB
keyboard driver. Remove usb_event_poll() as keyboard polling was
the only user of this API. With this patch USB keyboard works with
EHCI controllers again. Tested on a tegra2 seaboard.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Clean up added ehci-omap.c and make it generic for re-use across
omap-soc having same ehci ip block. Also pass the modes to be configured
from board file and configure the ports accordingly. All usb layers
are not cache aligned, till then keep cache off for usb ops as ehci will use
internally dma for all usb ops.
* Add a generic common header ehci-omap.h having common ip block
data and reg shifts.
* Rename and modify ehci-omap3 to ehci.h retain only conflicting
sysc reg shifts remove others and move to common header file.
* pass the board data for beagle/panda accordinly to use
ehci ports.
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Fix trailing white space, indentation by spaces instead of TABs,
excessive blank lines, trailing blank lines.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch allows USB to work on some hosts, which need additional frobing after
the host was powered up via regular USB powerup sequence.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
This is useful for USB Transceivers init etc.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Wolfgang Grandegger <wg@denx.de>
Cc: Jason Liu <r64343@freescale.com>
It's derived from ehci-mxc and uses the header files of the
ehci-fsl interface. The callback board_ehci_hcd_init() has
been introduced to allow for board-specific setup when USB
is started.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
CC: Stefano Babic <sbabic@denx.de>
CC: Remy Bohmer <linux@bohmer.net>
According to EHCI specification v1.0, the controller should stabilize
the power on a port at most 20 ms after the port power bit transition.
So, we put this setting in the virtual descriptor corresponding field,
(bPwrOn2PwrGood = 10 => 10 x 2ms = 20ms), this saves about 500ms at each
controller initialization/enumeration.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Fix:
ehci-mxc.c: In function 'ehci_hcd_init':
ehci-mxc.c:113:6: warning: variable 'tmp' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
sl811-hcd.c: In function 'sl811_rh_submit_urb':
sl811-hcd.c:556:8: warning: variable 'wIndex' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
* 'master' of git://git.denx.de/u-boot-arm:
arm, davinci: add DAVINCI_MMC_CLKID
arm, davinci_emac: fix driver bug if more then 3 PHYs are detected
arm, davinci: da850/dm365 lowlevel cleanup
omap5: Add omap5_evm board build support.
omap4/5: Add support for booting with CH.
omap5: emif: Add emif/ddr configurations required for omap5 evm
omap5: clocks: Add clocks support for omap5 platform.
omap5: Add minimal support for omap5430.
omap: Checkpatch fixes
omap4: make omap4 code common for future reuse
GCC4.6: Squash warnings in onenand_base.c
GCC4.6: Fix common/usb.c on xscale
OneNAND: Add simple OneNAND SPL
PXA: vpac270: Enable the new generic MMC driver
PXA: Cleanup serial_pxa
PXA: Drop csb226 and innokom boards (unmaintained)
m28evk: Fix comment about the number of RAM banks
mx31: Fix checkpatch warnings in generic.c
mx31: Use proper IO accessor for GPR register
mx31: Remove duplicate definition for GPR register
qong: Use generic function for configuring GPR register
M28EVK: Enable USB HOST support
iMX28: Add USB HOST driver
iMX28: Add USB and USB PHY register definitions
M28: Add memory detection into SPL
iMX28: Fix ARM vector handling
M28: Add doc/README.m28 documentation
M28: Add MMC SPL
iMX28: Add support for DENX M28EVK board
iMX28: Add u-boot.sb target to Makefile
iMX28: Add image header generator tool
iMX28: Add driver for internal RTC
iMX28: Add GPMI NAND driver
iMX28: Add APBH DMA driver
iMX28: Add SPI driver
iMX28: Add GPIO control
iMX28: Add I2C bus driver
iMX28: Add PINMUX control
FEC: Add support for iMX28 quirks
iMX28: Add SSP MMC driver
iMX28: Initial support for iMX28 CPU
MX25: zmx25: GCC4.6 fix build warnings
da850: add new config file for AM18xx
BeagleBoard: config: Switch to ttyO2
OMAP3: Change omap3_evm maintainer
devkit8000: Fix NAND SPL on boards with 256MB NAND
integrator: enable Vpp and disable flash protection
integrator: add system controller header
integrator: make flash writeable on boot
integrator: use io-accessors for board init
integrator: move text offset to config
integrator: pass configs for core modules
ARM: remove superfluous setting of arch_number in board specific code.
SPL: Allow ARM926EJS to avoid compiling in the CPU support code
integrator: do not test first part of the memory
arm: a320: fix broken timer
ARM: define CONFIG_MACH_TYPE for all ronetix boards
dm646x: pass board revision info to kernel
dm646x: add new configuration for dm6467T
arm, davinci: Fix setting of the SDRAM configuration register
arm, davinci: Remove the duplication of LPSC functions
arm, davinci: Rename AM1808 lowlevel functions to DA850
da8xxevm: fix build error
ARM: re-add MACH_TYPE_XXXXXX for VCMA9 board and add CONFIG_MACH_TYPE
Fix:
ehci-fsl.c: In function 'ehci_hcd_init':
ehci-fsl.c:43:7: warning: variable 'usb_phy' set but not used [-Wunused-but-set-variable]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This driver supports both EHCI ports on the i.MX28 CPU.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
The USB port to be used is determined by CONFIG_MXC_USB_PORT.
So, it appears that the comment is not correct. Remove it.
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
For files like the drivers/serial/serial.c, it must include the
platform file, as the CONFIG_SYS_NS16550_COM1 must reference to the
definition in the platform definition files.
Include the platform definition file in the config file, so that it
would decouple the dependence for the driver files.
Signed-off-by: Lei Wen <leiwen@marvell.com>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Fix:
ohci-hcd.c: In function 'dl_transfer_length':
ohci-hcd.c:968:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Acked-by: Remy Bohmer <linux@bohmer.net>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With this, the EHCI seems to "recover" from a timeout. This is particularly
observable if you were to ping the wrong IP Address and then ping the correct
one or if there was a temporary failure during tftp sessions.
All it takes is one timeout to disable it. If you have a noisy network (lot
of traffic), even if the traffic is not for the board, the timeouts don't occur.
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove __attribute__ ((packed)) to prevent byte access to soc
registers in some gcc versions.
Having patches to enable ehci for the BeagleBoard lying around for
several months, this one was the show-stopper.
Switched to align(4), rather than remove the attribute, per suggestion
from Alexander.
Credits have to go to Laine Walker-Avina <lwalkera@ieee.org> for
finding the problem.
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Cc: Alexander Holler <holler@ahsoftware.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fail in build, because argument of inl used in r8a66597_read_fifo is wrong.
r8a66597.h:441:35: error: macro "inl" passed 2 arguments, but takes just 1
In file included from r8a66597-hcd.c:25:
r8a66597.h: In function ‘r8a66597_read_fifo’:
r8a66597.h:441: error: ‘inl’ undeclared (first use in this function)
r8a66597.h:441: error: (Each undeclared identifier is reported only once
r8a66597.h:441: error: for each function it appears in.)
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Adding support for USB host on imx25 using the internal PHY. Changing the name
of base address define for imx31 to get some unification.
Signed-off-by: Matthias Weisser <weisserm@arcor.de>
As exception among the i.MX processors, the i.MX31 has headers
without general names (mx31-regs.h, mx31.h instead of imx-regs.h and
clock.h). This requires several nasty #ifdef in the drivers to
include the correct header. The patch cleans up the driver and
renames the header files as for the other i.MX processors.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add ULI1575 EHCI controller to the list of the supported devices.
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds support for the PI7C9X442SL PCIe EHCI host controller
from Pericom.
Tested at P4080DS eval board from Freescale.
Signed-off-by: Ralf Trübenbach <ralf.truebenbach@men.de>
Cc: Remy Bohmer <linux@bohmer.net>
Changed both to use a common timeout for URB submission, since they were using
different values and EHCI's was too short.
Also fixed EHCI to actually check if urb submission succeeded, rather than
silently continuing into the weeds.
Change-Id: I7f71499ffaa05187d8e5618db2419e1606007b82
Signed-off-by: Simon Glass <sjg@chromium.org>
Calling usb_dev_init() from within the EHCI host driver is wrong.
The EHCI host driver should have no dependency/interconnection to the
USB device driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This patch fixes a problem noticed on lwmon5 (PPC440EPx) using the
common EHCI driver, when "usb reset" is issued multiple times.
Upon the 2nd (and further) "usb reset" command, the command fails
with the following messages:
=> usb reset
(Re)start USB...
USB: Register 1111 NbrPorts 1
USB EHCI 1.00
scanning bus for devices... 5 USB Device(s) found
scanning bus for storage devices... 2 Storage Device(s) found
=> usb reset
(Re)start USB...
USB: EHCI fail to reset
Error, couldn't init Lowlevel part
This patch fixes this problem. Now "usb reset" can be called multiple
times.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
This watchdog reset call is needed here, otherwise the lwmon5 board
(PPC440EPx based) will reset upon the "usb reset" command.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Checking the status field of the qTD token in the current code
do not take into acount cases where endpoint stall (halted) bit
is set together with XactErr status bit. As a result clearing
stall on an endpoint won't be done if this status bit was also
set. Check for halted bit and report USB_ST_STALLED status
if the host controller also indicates endpoit stall condition.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
This patch solves a problem with USB hanging under higher load on a
i.MX31 board. It falls into class of typical USB problems and fixes:
if you don't understand the real cause, add a delay somewhere.
The problem appeared after introduction of ELF relocation, which
results in smaller code, which appears to run faster (probably because
it fits better in the cache); turning off the instruction cache,
adding debug printf()s and increasing the delay have all been found to
make the problem go away.
Moving the original "udelay(1)" up in the code to it's new place made
the problem appear much less frequently. Increasing the delay to 2
microseconds then made the code run reliably in all (hour-long) tests.
To be on the safe side, we set it to 5 microseconds here.
Signed-off-by: Heiko schocher <hs@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
Commit 3ed1607 "USB: sync Queue Element Transfer Descriptor against
EHCI spec" added an "__attribute__ ((aligned (32)))" to the
declaration of struct qTD, as used for example in the Linux kernel as
well.
However, it turns out that this attribute causes errors in "usb start"
(like "ERROR: NOT USB_CONFIG_DESC 7b" and similar). Drop the attribute
again.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Stefano Babic <sbabic@denx.de>
It is useful to know the EHCI-PCI hccr, hcor and hc_lenght to make sure it was
successfully registered, and at the correct location.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Appendix B "EHCI 64-Bit Data Structures" of the "Enhanced Host
Controller Interface Specification for Universal Serial Bus" (Rev.
1.0, March 12, 2002) defines additional fields which were missing in
U-Boot's struct qTD; as these are also present in recent versions of
struct ehci_qtd in the Linux kernel, we add them here, too.
This fixes some nasty memory corruption problems.
Reported-by: Dan Lykowski <lykowdk@gmail.com>
See http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/76942
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Cc: Dan Lykowski <lykowdk@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Sometimes a usb tree is not popolated after a system reset.
It seems a delay is required after setting the USB ports
for the MX.31 before resetting the ehci controller.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This fixes TIMEOUT with my Kingston 32GB USB3.0 flashdrive, which I experienced
on my PXA270 (USB 1.1) Vpac270 board.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This avoids a build warning that you see if anyone in the
header chain has included io.h (which is coming shortly). The previous
code redefined readl/writel; this patch renames it to be specific to
ohci. The defines are also moved from ohci-hcd.c to ohci.h.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
ehci_submit_async() doesn't really zero out the QH transfer overlay (as the EHCI
specification suggests) which leads to the controller seeing the "token" field
as the previous call has left it, i.e.:
- if a timeout occured on the previous call (Active bit left as 1), controller
incorrectly tries to complete a previous transaction on a newly programmed
endpoint;
- if a halt occured on the previous call (Halted bit set to 1), controller just
ignores the newly programmed TD(s) and the function then keeps returning error
ad infinitum.
This turned out to be caused by the wrong orger of the arguments to the memset()
call in ehci_alloc(), so the allocated TDs weren't cleared either.
While at it, stop needlessly initializing the alternate next TD pointer in the
QH transfer overlay...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Add NEC EHCI controller to the list of the supported devices.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
drivers/usb/host/ehci-pci.c | 1 +
1 file changed, 1 insertion(+)
Commit b416191a14 (Fix EHCI port reset.) didn't
move the code that checked for successful clearing of the port reset bit from
ehci_submit_root(), relying on wait_ms() call instead. The mentioned code also
erroneously reported port reset state when the reset was already completed.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
USB devices on the 2nd port are not detected and I get the following message:
The request port(1) is not configured
That's with default CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS value of 2. 'req->index'
is 1-based, so the comparison in ehci_submit_root() can't be correct.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
On little endian machines, EHCI root hub's USB revision is reported as 0.2 --
cpu_to_le16() was missed in the initializer for the 'bcdUSB' descriptor field.
The same should be done for the 'bcdDevice' field.
Signed-off-by: Sergei Shtylyov <sshtylyov@mvista.com>
This patch is part of migrating the AT91 support towards
using C struct for all SOC access.
It removes one more CONFIG_AT91_LEGACY warning.
at91_pmc.h needs cleanup after migration of the drivers
has been done.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
* add's a warning to all files, which need update to new SoC access
* convert common files in cpu/../at91 and a lot of drivers to use
c stucture SoC access
Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
In USB ehci driver, the port reset is not terminated. EHCI spec says "A host
controller must terminate the reset and stabilize the state of the port within
2 milliseconds". Without termination, a port stays at reset state. This is
observed on ppc4xx(sequoia) boards.
Signed-off-by: Chris Zhang <chris@seamicro.com>
The header files usb.h and usbdescriptors.h have the same nameed
structure definitions for
usb_config_descriptor
usb_interface_descriptor
usb_endpoint_descriptor
usb_device_descriptor
usb_string_descriptor
These are out right duplicates in usb.h
usb_device_descriptor
usb_string_descriptor
This one has extra unused elements
usb_endpoint_descriptor
unsigned char bRefresh
unsigned char bSynchAddress;
These in usb.h have extra elements at the end of the usb 2.0
specified descriptor and are used.
usb_config_descriptor
usb_interface_descriptor
The change is to consolidate the definition of the descriptors
to usbdescriptors.h. The dublicates in usb.h are removed.
The extra element structure will have their name shorted by
removing the '_descriptor' suffix.
So
usb_config_descriptor -> usb_config
usb_interface_descriptor -> usb_interface
For these, the common descriptor elements are accessed now
by an element 'desc'.
As an example
- if (iface->bInterfaceClass != USB_CLASS_HUB)
+ if (iface->desc.bInterfaceClass != USB_CLASS_HUB)
This has been compile tested on MAKEALL arm, ppc and mips.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
This patch adds a unified s3c24x0 cpu header file that selects the header
file for the specific s3c24x0 cpu from the SOC and CPU configs defined in
board config file. This removes the current chain of s3c24-type #ifdef's
from the s3c24x0 code.
Signed-off-by: Kevin Morfitt <kevin.morfitt@fearnside-systems.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change is cheked in Linux source and fix found to be in sync.
This patch is tested for USB host interface on Kirkwood based
Sheevaplug platform (ARM little endian board)
Risk: the impact of this patch is not validated on big endian board.
This need to be checked...
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
ehci-hcd.c: In function 'ehci_submit_root':
ehci-hcd.c:719: warning: value computed is not used
ehci-hcd.c:748: warning: value computed is not used
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch fixes the access to the 'ehci' struct elements which should
have been taken care off in 4ef01010aa
Sorry about that.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch reorganizes/reworks the USB support for mpc83xx
as under:-
* Moves the 83xx USB clock init from drivers/usb/host/ehci-fsl.c to
cpu/mpx83xx/cpu_init.c
* Board specific usb_phy_type is read from the environment
* Adds USB EHCI specific structure in include/usb/ehci-fsl.h
* Copyrights revamped in most of the following files
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
The following patch moves 8xxx-specifc USB #defines from
drivers/usb/host/ehci-fsl.h to include/usb.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
To prepare for the 85xx USB support, which requires interface enablement
only once in (specified) order, no different than instructions for
enabling the interface under 83xx. It is unknown why the original author
enabled the interface twice (checked for references in errata, etc).
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch corrects the missing PLLB initialization in usb_cpu_init()
for AT91SAM9261.
Because of the missing PLLB initialization, the USB support for all
AT91SAM9261 based boards will work only if the PLLB is configured by a
precedent bootloader.
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
__attribute__ follows gcc's documented syntax and is generally more
common than __attribute. This change is only asthetic and should not
affect functionality.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
move to linux usb driver organisation
as following
drivers/usb/gadget
drivers/usb/host
drivers/usb/musb
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
