We don't need to implement direction_input() and direction_output()
anymore. Drop them and use update_flags() instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update this driver to use the common method of putting the driver
operations in an 'ops' variable install of calling gpio_get_ops()
repeatedly. Make it const since operations do not change.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The new update_flags() method is more flexible since it allows the
driver to see the full flags all at once. Use that in preference to these
two functions. Add comments to that effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is convenient to be able to adjust some of the flags for a GPIO while
leaving others alone. Add a function for this.
Update dm_gpio_set_dir_flags() to make use of this.
Also update dm_gpio_set_value() to use this also, since this allows the
open-drain / open-source features to be implemented directly in the
driver, rather than using the uclass workaround.
Update the sandbox tests accordingly. This involves a lot of changes to
dm_test_gpio_opendrain_opensource() since we no-longer have the direciion
being reported differently depending on the open drain/open source flags.
Also update the STM32 drivers to let the uclass handle the active low/high
logic.
Drop the GPIOD_FLAGS_OUTPUT() macro which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Allow this function to see all flags, including the internal sandbox ones.
This allows the tests to fully control the behaviour of the driver.
To make this work, move the setting of GPIOD_EXT_HIGH -to where the flags
are updated via driver model, rather than the sandbox 'back door'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
At present we have the concept of a pin's external value. This is what
is used when getting the value of a pin. But we still set the
GPIOD_IS_OUT_ACTIVE flag when changing the value. This is not actually
correct, since if the pin changes from output to input, the external
value need not change. Adjust the logic for this difference.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
At present with the sandbox GPIO driver it is not possible to change the
value of GPIOD_IS_OUT_ACTIVE unless the GPIO is an output. This makes it
hard to test changing the flags since we need to be aware of the internal
workings of the driver.
The feature is designed to aid testing.
Split this feature out into a separate sandbox-specific flag, so that the
flags can change unimpeded. This will make it easier to allow updating the
flags in a future patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the terminology in this driver to reflect that fact that all flags
are handled, not just direction flags.
Create a new access function to get the full GPIO state, not just the
direction flags. Drop the static invalid_dir_flags since we can rely on a
segfault if something is wrong.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This function can be used to get any flags, not just direction flags.
Rename it to avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
It is more useful to be able to read all the flags, not just the direction
ones. In fact this is what the STM32 driver does. Update the method name
to reflect this.
Tweak the docs a little and use 'flagsp' as the return argument, as is
common in driver model, to indicate it returns a value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
The current method is a misnomer since it is also used (e.g. by stm32) to
update pull settings and open source/open drain.
Rename it and expand the documentation to cover a few more details.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
These functions use devicetree and cannot work with of-platdata, which has
no runtime devicetree.
If they are used, the current linker error is confusing, since it talks
about missing functions in the bowels of driver model.
Avoid compiling these functions at all with of-platdata, so that a
straightforward link error points to the problem.
Series-changes; 3
- Fix 'wprl' typo
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
DM_VIDEO migration deadline is already expired, but around
80 Allwinner boards are still using video in a legacy way:
===================== WARNING ======================
This board does not use CONFIG_DM_VIDEO Please update
the board to use CONFIG_DM_VIDEO before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Convert the legacy video driver over to the DM_VIDEO framework. This is
a minimal conversion: it doesn't use the DT for finding its resources,
nor does it use DM clocks or DM devices for the outputs (LCD, HDMI, CVBS).
Tested in Bananapi M1+ Plus 1920x1200 HDMI out. (Jagan)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
[Andre: rebase and smaller fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
All debug messages from ep0.c except a few are printed by dbg_ep0() macro.
So for remaining few exceptions use also dbg_ep0() instead of serial_printf().
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If we do not set FIFO buffer address and size for some endpoint which is in
use then default programmed address 0x0 would be used which is in conflict
with address of FIFO buffer for endpoint 0. Moreover address of FIFO buffer
for endpoint 0 cannot be programmed, it is fixed to 0x0. Sharing address
space between more endpoints cause data loss and unexpected errors.
This patch is fixing transmission of characters over usbtty serial console
and allows using of usbtty for debugging purposes on Nokia N900.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Interrupt for EP0 is indicated in intrtx register via first bit. This bit
is set for both RX and TX despite register has only TX in its name. First
bit in intrrx register is reserved, not used and never set.
So remove calling musb_peri_ep0() function at every iteration of udc_irq()
and musb_peri_rx() and call it only from musb_peri_tx() when correct
interrupt bit in initrtx it set.
Address from SET ADDRESS command must be set to faddr register only after
acknowledging SERV_RXPKTRDY followed by received EP0 interrupt. So prior
calling musb_peri_ep0_set_address() check for EP0 interrupt instead of
(incorrect) MUSB_INTR_SOF interrupt.
This patch fixes issue that host (computer) cannot register U-Boot USB
device and is failing with errors:
usb 1-1: new full-speed USB device number 86 using xhci_hcd
usb 1-1: Device not responding to setup address.
usb 1-1: Device not responding to setup address.
usb 1-1: device not accepting address 86, error -71
U-Boot was writing address to faddr register too early and did not wait for
correct interrupt after which should update address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If musb_peri_rx_ep() was called to process received HW buffer but U-Boot
cannot read it yet (e.g. because U-Boot SW buffer is full) then interrupt
was marked as processed also when HW buffer stayed unprocessed.
U-Boot tried to process this buffer again when it received interrupt again,
but it can receive it only when sender (host) sends a new data. As sender
(host) is not going to send a new data until U-Boot process current data
this issue caused a deadlock in case sender (host) is emitting data faster
than U-Boot can process it.
Reading musb intrrx register automatically clears this register and marks
interrupt as processed. So to prevent marking interrupt in U-Boot as
processed, adds a new variable pending_intrrx which would contain
unprocessed bits of intrrx register.
For a second step, every time when musb_peri_rx_ep() is called and there
are waiting data to be processed (signaled by MUSB_RXCSR_RXPKTRDY) either
acknowledge sender (via musb_peri_rx_ack()) that whole HW buffer was
processed or set corresponding bit in pending_intrrx that HW buffer was not
fully processed yet and next iteration is required after U-Boot allocates
space for reading HW buffer.
This patch fixes receiving large usb buffers, e.g. file transfer via Kermit
protocol implemented by 'loadb' U-Boot command over usbtty serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
If udc_endpoint_write() was called with bigger payload which does not fit
into one USB packet it is needed to transmit payload in more USB packets.
First packet is transmitted by udc_endpoint_write() call itself and other
packets are put into waiting queue.
Implement function musb_peri_tx() which checks if endpoints are ready for
transmit and continue transmission of waiting queue.
This patch fixes sending big output from printenv command over usbtty
serial console.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>>
PERI_RXCSR is 16bit register so store its value into 16bit local variable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This patch fixes configuring FIFOs for one-directional endpoints which have
only one queue (either RX or TX, but noth both).
Size of FIFO buffer is 2^(idx+3) bytes and starting address is 2^(addr+3).
Moreover first 64 bytes are reserved for EP0.
Without this patch if FIFO size specified by caller was zero then idx was
incorrectly calculated (expr. ffs(0)-1) and size overflowed in fifosz
register. This register uses has only 4 bits for FIFO size. Moreover
specifying zero buffer size is not possible (with idx=0 is minimal buffer
size 8 bytes).
So even for one-directional endpoints we need to correctly specify both
(RX and TX) FIFO buffer sizes and its addresses.
This patch is fixing calculation of start address and buffer size to
minimal value and ensures that it would not overlap with buffer reserved
for EP0.
This issue caused loose of packets on USB bus in both directions and
basically usbtty was unusable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Without this patch clearing was done only when U-Boot was compiled with
MUSB Host Controller. But clearing of data toggle bit is needed also for
MUSB Device Controller otherwise Device Controller does not work correctly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Function next_urb() selects the last urb data buffer from linked list to
which next data from usbtty's puts function should be appended.
But to check if TX data still exists it is needed to look at the first urb
data buffer from linked list. So check for endpoint->tx_urb (first from the
linked list) instead of current_urb (the last from the linked list).
Successful call to udc_endpoint_write() may invalidate active urb and
allocate new urb in queue which invalidates pointer returned by next_urb()
function.
So call next_urb() prior putting data into urb buffer and call it every
time after using udc_endpoint_write() function to prevent sending data from
usbtty's puts function in incorrect order.
This patch fixes issue that usbtty code does not transmit data when they
are waiting in the tx queue.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
This function has incorrect implementation of prepending CR prior LF.
Without this patch it prepended CR prior whole string which is going to be
written and let LF without leading CR. Fix this issue by inserting CR at
correct place to make output on usbtty serial console more readable.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Update this to use log_debug() instead of the old debug().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
At present the security chip is not used in these U-Boot phases. Update
the Makefile to exclude it.
Fix a few logging statements while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to. This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value. Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.
Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g. COLD vs WARM resets). As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).
To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely. Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.
This transformation was done with the following coccinelle patch:
@@
expression argvalue;
@@
- reset_cpu(argvalue)
+ reset_cpu()
@@
identifier argname;
type argtype;
@@
- reset_cpu(argtype argname)
+ reset_cpu(void)
{ ... }
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RPi4 armv7 build we have the situationt that we use physical
addresses of 64 bit, while the virtual addresses are 32 bit.
Remap the base address in this scenario via map_physmem().
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add tuning functionality which is needed for HS200 mode.
For HS200, program the correct needed 1.8 voltage
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
SAMA7G5 supports slew rate configuration. Adapt the driver for this.
For switching frequencies lower than 50MHz the slew rate needs to
be enabled. Since most of the pins on SAMA7G5 fall into this category
enabled the slew rate by default.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
On imx6Q/imx6DL, we find if config the DTOCV to 0~3, it will impact
cmd6 behavior, after cmd6 get transfer complete interrupt, the data0
line will keep low over 5 seconds. This should be a IC bug on imx6Q/DL.
For other platforms, do not has this issue.
To fix this issue, fix the DTOCV to 0xE, the max setting, this also align
with Linux configuration.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a compatible for i.MX51 so that i.MX51 can use this driver
via driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Set default critical/alert temperature and enabling monoitoring.
Without calling imx_tmu_enable_msite() monitoring will not be enabled
and read_temperature will return 0. Additionally without setting alert
temperature will cause imx_tmu_get_temp() to spin indefiniately thinking
the system needs to cool.
This resolves the board spinning endlessly when enabling IMX_TMU in the
SPL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This adds support for partitions of the form "dev.hwpart:part" and
"dev#partname". This allows one to flash to eMMC boot partitions without
having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to
flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME.
Lastly, one can also flash MMC devices other than
CONFIG_FASTBOOT_FLASH_MMC_DEV.
Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV
is used only when necessary for existing functionality. For those cases,
fastboot_mmc_get_dev has been added as a helper function. This allows
There should be no conflicts with the existing system, but just in case, I
have ordered detection of these names after all existing names.
The fastboot_mmc_part test has been updated for these new names.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the next commit more readable by doing the move now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The only thing mmcpart was used for was to pass to blk_dselect_hwpart.
This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The
error handling is dropped, but it is reintroduced in the next commit
(albeit less specificly).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support writing to the sandbox mmc backed by an in-memory
buffer. The unit test has been updated to test reading, writing, and
erasing. I'm not sure what MMCs erase to; I picked 0, but if it's 0xFF
then that can be easily changed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart form the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The datasheet only lists one dummy byte in the 0xEB operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Reto Schneider:
- Linux patch ported to U-Boot
- Checked for compatibility with GD5F1GQ4xBxxG
- Fixed operation code in original commit message (0xEH -> 0xEB)
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
On the i.MX8M Mini, ret = clk_set_rate() sets ret to the value of the
rate the clock was able to set. When checking for errors, it only
checks that it is not NULL. Since positive numbers are not errors,
only check for negative numbers when handling errors.
Fixes: 383fded70c ("spi: nxp_fspi: new driver for the FlexSPI controller")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The code was processed with unifdef utility to omit portions not
relevant to A38x and DDR3. This removes usage of many macros, including
A70X0, A80X0 and A3900. It seems that the unifdef utility did not remove
the macros from #else comment.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Bump version of a38x DDR3 trianing to version 14.0.0 to reflect the
version in the mv-ddr-devel branch of upstream repository
https://github.com/MarvellEmbeddedProcessors/mv-ddr-marvell.git.
There is a new version numbering system, where after 18.12.0 came
1.0.0, 2.0.0, and so on until 14.0.0. So 14.0.0 is newer than 18.12.0.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 56db5d1464b44df10a02b99e615ebd6f6a35c428 upstream.
@pali suggested this change
In commit 6285efb ("mv_ddr: add support for twin-die combined memory
device") was added support for twin-die combined memory device and
default value for explicitly uninitialized structure members is zero, s
also twin_die_combined is initialized to zero. Which means COMBINED
value.
As prior this commit there was no support for twin-die combined memory
device, default value for twin_die_combined should be NOT_COMBINED. This
change change order of enum mv_ddr_twin_die to ensure that NOT_COMBINED
has value zero.
Signed-off-by: heaterC <airyguy@gmx.de>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2bdd12dd68b1f8e27a03a3443ae49a09a14c18e4 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes code in ddr3_training.c.
Import this change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit c8b301463d508c807a33f7b7eaea98bbda4aa35e upstream.
The funtion returnd cs size in byte instead of MB, that cause
calculation error since the caller was expected to get u32 and when he
got above 4G it refers it as 0.
The fix was to get the cs memory size from function as in MB and then
multiply it by 1MB.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit d653b305d0b3da9727c49124683f1a6d95d5c9a5 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 20c89a28548cdab11f88d2ec8936344af0686a1e upstream.
WL phase correcion stage is failing while using bus_width of 16bit, not
to be fix this stage is un-necessary when working with bus_width of 16
bit.
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6285efb8a118940877522c4c07bd7c64569b4f5f upstream.
the twin-die combined memory device should be treatened as X8
device and not as X16 one
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
[ - the default value for twin_die_combined is set to NOT_COMBINED for
all boards, as this was default behaviour prior this change ]
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 2d3b9437cf38c06c4330e0de07f29476197f5e04 upstream.
The ODT enable heuristic based on active chip-selects is not always
correct. Some board might use two chip-selects, but have only one ODT
line connected. Allow board specific mv_ddr_topology_map to directly set
the ODT configuration register value.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 3908e20c6c520339e9bddb566823ae5e065d5218 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ab9240402a70cc02496683971779e75eff410ab4 upstream.
- function mv_ddr_spd_die_capacity_user_get() has a bug,
since it insert a user memory enum to it,
instead of SPD memory enum (which are different)
- fix: remove mv_ddr_spd_die_capacity_user_get() function.
- memory size with 64 and 32 bit already calculated correctly
at mv_ddr_mem_sz_per_cs_get() function
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Stefan Chulski <Stefan.Chulski@cavium.com>
Reviewed-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 6c705ebc0d70f67ed7cae83ad1978c3305ef25be upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header mv_ddr_topology.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 61a8910998d7b553e80f600ebe8147a8b98f0945 upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit 32800667b375ebd1f82120da0f3479b1cf52d96d upstream.
Required changes made for 32bit ddr support.
An update is made to the topology map, according to
bus_act_mask, set in the dram_port.c
Signed-off-by: Alex Leibovich <alexl@marvell.com>
Reviewed-by: Nadav Haklai <Nadav.Haklai@cavium.com>
Reviewed-by: Kostya Porotchkin <Kostya.Porotchkin@cavium.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit a165037ec26f301be75e1fabc263643683e85255 upstream.
The commit mentioned above changes non-DDR3 stuff in upstream, but it
also changes header ddr_topology_def.h.
Import this header change to remain consistent with upstream.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
commit ce62bef8fac559e27245259882e45f19cdc293ad upstream.
- fix JIRA A7K8K-5056
- remove TEST_PATTERN write at the load patern stage earlier to WL SUP stage
- the WL SUP stage already writes this pattern to the memory, if the pattern exist at the memory
then the algorithm will fail, since it think that there are no phase to correct
Signed-off-by: Moti Buskila <motib@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Tested-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Linux displays the real PCIe card connected to a mvebu PCIe slot as
device 0, not 1. This is done by setting local dev number to 1, so that
the local "Marvell Memory controller" device is on address 1.
Let's do it also in U-Boot.
With this commit the pci command in U-Boot prints something like:
=> pci
Scanning PCI devices on bus 0
BusDevFun VendorId DeviceId Device Class Sub-Class
_____________________________________________________________
00.00.00 0x168c 0x003c Network controller 0x80
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Refactor validation of bdf parameter in mvebu_pcie_read/write_config
functions.
We can simplify the code by putting the validation into separate
function.
Also there are always only two devices visible on local bus:
* on slot configured by function mvebu_pcie_set_local_dev_nr()
(by default this register is set to 0) there is a
"Marvell Memory controller", which isn't useful in root complex
mode,
* on all other slots the real PCIe card connected to the PCIe slot.
We can simplify the code even more by simply allowing access only to
the real PCIe card.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Other drivers (aardvark, intel_fpga) print "(addr,size,val)" when
debugging is enabled. Print size for pci_mvebu as well.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Write bdf address in a same way in mvebu_pcie_read/write_config.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI uclass maps PCI bus numbers to the seq member of struct udevice.
Use dev_seq(dev) as the bus number in mvebu_pcie_probe instead of an
incrementing a static variable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix usage of VL805 XHCI PCIe controller when it is connected via PCIe to
Armada 3720 SOC. Without this U-Boot crashes when trying to access
enumerated USB devices connected to this XHCI PCIe controller.
This should be done according to the PCIe Link Initialization sequence, as
defined in Marvell Armada 3720 Functional Specification.
Linux has this code too.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The NOR flash w25q128 denoted by JEDEC ID 0xef4018 actually represents
various models. From Winbond's website, I could only find 3 types of
them:
W25Q128JV-IQ/JQ
datasheet:https://www.winbond.com/resource-files/
w25q128jv%20revg%2004082019%20plus.pdf
W25Q128FV (SPI Mode)
datasheet: https://www.winbond.com/resource-files/
w25q128fv%20rev.m%2005132016%20kms.pdf
W25Q128BV
datesheet: https://www.winbond.com/resource-files/
w25q128bv_revh_100313_wo_automotive.pdf
According to the datasheets, all of these 3 types support BP(0,1,2) and
TB bits in the status register (SR), so it could reuse the flash
protection logic for ST Micro.
So it should be safe to add the SPI_NOR_HAS_LOCK and SPI_NOR_HAS_TB
flags to the w25q128 entry of spi_nor_ids table.
Signed-off-by: Su Baocheng <baocheng.su@siemens.com>
[jagan: remove comments in spi-nor-ids.c]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The set_speed() callback should configure the bus speed, make it so.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When copying to a u32 field we should use sizeof(u32) and not
sizeof(*u32) in memcpy.
On 64bit systems like cortina_presidio-asic-emmc_defconfig using
sizeof(*u32) leads to a buffer overrun.
Fixes: febe13b438 ("net: cortina_ni: Add eth support for Cortina Access CAxxxx SoCs")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
ca_do_bch_correction() takes a random value from the stack and starts
counting bitflips from this value. Initialize the counter.
This passed unnoticed as the value is finally ignored in the call
hierarchy.
Fixes: 161df94b3c ("mtd: rawnand: cortina_nand: Add Cortina CAxxxx SoC support")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The values of left_edge[0] and right_edge[0] are overwritten before they
are used. Remove the superfluous assignments.
Fixes: 285b3cb939 ("dm: ddr: socfpga: fix gen5 ddr driver to not use bss")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In 8a8d24bd Simon dropped data from all the various _platdata calls
but it seems this wasn't caught for the RNG200 driver from when it
was posted to merged. This fixes that issue.
Fixes: 537f0018 (rng: Add iProc RNG200 driver)
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
VIRTIO_ID_MAX_NUM is the largest device ID plus 1. Therefore a device id
cannot be greater or equal to VIRTIO_ID_MAX_NUM. Fix the comparison
accordingly.
Fixes: 8fb49b4c7a ("dm: Add a new uclass driver for VirtIO transport devices")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYDUezQAKCRDKSWXLKUoM
IbtgAJ9jZ+BOtwFaHR19TENC2DsHTINnnwCfSDn3fU0OFJRI0HD7pRxXr4xrb3M=
=Kr8x
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.04-rc3
qspi:
- Support for dual/quad mode
- Fix speed handling
clk:
- Add clock enable function for zynq/zynqmp/versal
gem:
- Enable clock for Versal
- Fix error path
- Fix mdio deregistration path
fpga:
- Fix buffer alignment for ZynqMP
xilinx:
- Fix reset reason clearing in ZynqMP
- Show silicon version in SPL for Zynq/ZynqMP
- Fix DTB selection for ZynqMP
- Rename zc1275 to zcu1275 to match DT name
If zynqmp_qspi_set_speed() is called multiple times with the same speed,
then on the second call it will skip recalculating the baud_rate_val as
it assumes the speed is already configured correctly. But it will still
write the baud_rate_val to the configuration register and call
zynqmp_gqspi_set_tapdelay(). Because it skipped recalculating the
baud_rate_val, it will use the initial value of 0 . This causes the
driver to run at maximum speed which for many spi flashes is too fast and
causes data corruption.
Instead only write out a new baud_rate_val if we have calculated the
correct baud_rate_val.
This opens up another issue with the "if (speed == 0)", we don't save
off the new plat->speed_hz value when setting the baud rate on the
speed=0 path. Instead mimic what the Linux zynqmp gqspi driver does, and
have speed==0 just use the same calculation as a normal speed. That will
cause the baud_rate_val to use the slowest speed possible, which is the
safest option.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable rx clock along with tx clock for versal platform. Use compatible
data to enable/disable clocks in the driver.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Enable i2c controller clock from driver probe function
by calling clk_enable().
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add clock enable functionality in versal clock driver to enable
clocks from peripheral drivers using clk_ops.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add clock enable functionality in zynqmp clock driver to enable
clocks from peripheral drivers using clk_ops.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
A lot of Xilinx drivers are checking -ENOSYS which means that clock driver
doesn't have enable function. Remove this checking from drivers and create
dummy enable function as was done for clk_fixed_rate driver by
commit 6bf6d81c11 ("clk: fixed_rate: add dummy enable() function").
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Due to pointer arithmetic, "sizeof(u32) * ARCH_DMA_MINALIGN" is
subtracted. It seems that the original intention was to just subtract
ARCH_DMA_MINALIGN. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently support for the Samsung serial port driver is part
of CONFIG_S5P which controls selection of several drivers for
the S5P family. Give it its own config option such that we
can use it on other SoCs as well.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Remove pmic_max8997/8 files about no-DM.
There are already existed max8997/8 as driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The previous version printed the same debug message for both the enable
and disable routines without highlighting whether you were enabling or
disabling the module. It is now clear whether you are enabling or
disabling the module.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
i2c changes for v2021.04
new feature:
- Allow disabling driver model for I2C in SPL
fixes:
- i2c-gpio: Fix GPIO output
- at91: fix crash when using 'i2c probe'
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.
CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.
All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
At present if U-Boot proper uses driver model for I2C, then SPL has to
also. While this is desirable, it places a significant barrier to moving
to driver model in some cases. For example, with a space-constrained SPL
it may be necessary to enable CONFIG_SPL_OF_PLATDATA which involves
adjusting some drivers.
This patch introduces a separate Kconfig symbols for enabling DM_I2C and
DM_I2C_GPIO support in SPL.
This will also help to get away from dirty workarounds to
achieve non-DM I2C support for SPL, which is currently used in some
board header files like:
ifdef CONFIG_SPL_BUILD
undef CONFIG_DM_I2C
endif
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
When issuing 'i2c probe', the driver was crashing, because at probe
there is a request with zero length buffer to write to i2c bus.
The xfer_msg function assumes the buffer is always there, and never
checks for the buffer length.
=> i2c dev 0
Setting bus to 0
=> i2c probe
Valid chip addresses:
data abort
pc : [<7ffa97dc>] lr : [<7ffa96f8>]
reloc pc : [<66f277dc>] lr : [<66f276f8>]
sp : 7fb7c110 ip : 7ff87a28 fp : 7ff99938
r10: 00000002 r9 : 7fb7dec0 r8 : 00000000
r7 : e181c600 r6 : 7fb88c20 r5 : 00000000 r4 : 7fb7c128
r3 : 00000000 r2 : 00000001 r1 : 00000000 r0 : 00000009
Flags: nZCv IRQs off FIQs off Mode SVC_32
Code: eb0092f4 e1a00005 e8bd81f0 e594300c (e5d33000)
Resetting CPU ...
Fixes: 8800e0fa20 ("i2c: atmel: add i2c driver")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The dm_gpio_set_dir_flags function cannot be used to update the
configuration of a GPIO pin because it does a bitwise OR with the
existing flags. Looks like commit 788ea83412 ("gpio: add function
_dm_gpio_set_dir_flags") has introduced this behaviour and the i2c-gpio
driver has been broken since.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Heiko Schocher <hs@denx.de>
CC: Patrick Delaunay <patrick.delaunay@st.com>
Because the first PCIExAR(n) register is configured with the mapping,
It is the second PCIExAR(n) register that must be written with 0, not
the last one. Update the n from 4 to 1 to select the correct register.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Both the map address and mask must be power of two per documentation,
adjust the code accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add code to access the PCIe root bus space and configure it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mb862xx driver does not conform to the driver model and is unused.
Eliminate it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "boe,nv101wxmn51" to the compatible node. This is the panel for
chromebook_bob.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add "sharp,lq123p1jx31" to the compatible node. This is the panel for
chromebook_kevin.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mmc_spi_sendcmd(), mmc_spi_readdata() and mmc_spi_writedata() are
currently undocumented. Add comment blocks to explain the arguments
and the return value.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After command is sent and before card response shows up on the line,
there is a variable number of clock cycles in between called Ncr.
The spec [1] says the minimum is 1 byte and the maximum is 8 bytes.
Current logic in mmc_spi_sendcmd() has a flaw that it could only work
with certain SD cards with their Ncr being just 1 byte.
When resp_match is false, the codes try to receive only 1 byte from
the SD card. On the other hand when resp_match is true, the logic
happens to be no problem as it loops until timeout to receive as many
bytes as possible to see a match of the expected resp_match_value.
However not every call to mmc_spi_sendcmd() is made with resp_match
being true hence this exposes a potential issue with SD cards that
have a larger Ncr value.
Given no issue was reported as of today, we can reasonably conclude
that all cards being used on the supported boards happen to have a 1
byte Ncr timing requirement. But a broken case can be triggered by
utilizing QEMU to emulate a larger value of Ncr (by default 1 byte
Ncr is used on QEMU). This commit fixes such potential spec violation
to improve the card compatibility.
[1] "Physical Layer Specification Version 8.00"
chapter 7.5.1: Command / Response
chapter 7.5.4: Timing Values
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The argument check should happen before any transfer on the SPI lines.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
After issuing the switch command: Wait until 'current state' of the card
status becomes 'tran'. This prevents from response timeout at the next
command because of 'current state' = 'data'.
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
If DMA(SDMA or ADMA) is not used, the cache invalidation
after reading is no need, should be skipped. Otherwise
U-Boot may hang at the cache invalidation.
Found this issue and tested this fix on DragonBoard 410c.
Fixes: commit 4155ad9aac ("mmc: sdhci: fix missing cache invalidation after reading by DMA")
Signed-off-by: Yuezhang.Mo <Yuezhang.Mo@sony.com>
Reviewed-by: Andy Wu <Andy.Wu@sony.com>
The 'brcm,bcm2711-hdmi0' compatible string is used on RPi4 instead of
'brcm,bcm2835-hdmi' since the IP core was upgraded (now called VC6
instead of VC4). This has no functional change as far as u-boot driver
is concerned. So simply add the compatible string.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This will allow us to use DM variants of phys_to_bus()/bus_to_phys()
when relevant.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
So far we've been content with passing physical addresses when
configuring memory addresses into XHCI controllers, but not all
platforms have buses with transparent mappings. Specifically the
Raspberry Pi 4 might introduce an offset to memory accesses incoming
from its PCIe port.
Introduce xhci_virt_to_bus() and xhci_bus_to_virt() to cater with these
limitations, and make sure we don't break non DM users.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: fix compilation for 32 bit]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
fix from nicolas
Calculating the DMA offset between a bus address space and CPU's every
time we call phys_to_bus() and bus_to_phys() isn't ideal performance
wise, as it implies traversing the device tree from the device's node up
to the root. Since this information is static and available before the
device's initialization, parse it before the probe call an provide the
DMA offset in 'struct udevice' for the address translation code to use
it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add the following functions to get a specific device's DMA ranges:
- dev_get_dma_range()
- ofnode_get_dma_range()
- of_get_dma_range()
- fdt_get_dma_range()
They are specially useful in oder to be able validate a physical address
space range into a bus's and to convert addresses from and to address
spaces.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
So far we've assumed a fixed configuration for inbound windows as we had
a single user for this controller. But the controller's DMA constraints
were improved starting with BCM2711's B1 revision of the SoC, notably
available in CM4 and Pi400. They allow for wider inbound windows. We can
now cover the whole address space, whereas before we where limited to
the lower 3GB.
This information is passed to us through DT's 'dma-ranges' property and
it's specially important for us to honor it since some interactions with
the board's co-processor assume we're doing so (specifically the XHCI
firmware load operation, which is handled by the co-processor after
u-boot has correctly configured the PCIe controller).
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Make sure we handover the PCIe controller in a clean state. Some of the
devices hanging from the PCIe bus might need to be properly reset
through #PERST in order for Linux to be able to initialize them.
This is specially important in order to properly initialize Raspberry Pi
4 B and 400's USB chip.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The PCIe bus the controller is connected to might need to be removed
prior the handover. Make sure xhci-pci is also removed so as to avoid
unexpected timeouts or hangs.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
We find the iProc RNG200 in the Raspberry Pi 4. Add it to all it's
config so that it can be used.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: drop rpi_4_32b_defconfig]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add support for getting the 'vref-supply' regulator and register it as
ADC's reference voltage regulator, so clients can translate sampled ADC
values to the voltage.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a simple Analog to Digital Converter device based button driver. This
driver binds to the 'adc-keys' device tree node.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for random number generator RNG200.
This is for example found on RPi4.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
[mb: adapt to new struct driver memebers]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This driver is used for the Ethernet switch integrated into LS1028A NXP.
Felix on LS1028A has 4 front panel ports and two internal ports, I/O
to/from the switch is done through an ENETC Ethernet interface.
The 4 front panel ports are available as Ethernet interfaces and can be
used with the typical network commands like tftp.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
DSA stands for Distributed Switch Architecture and it covers switches that
are connected to the CPU through an Ethernet link and generally use frame
tags to pass information about the source/destination ports to/from CPU.
Front panel ports are presented as regular ethernet devices in U-Boot and
they are expected to support the typical networking commands.
DSA switches may be cascaded, DSA class code does not currently support
this.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
The DSA (Distributed Switch Architecture) implementation has made a
design decision when it got introduced to the Linux kernel in 2008.
That was to hide away from the user the CPU-facing Ethernet MAC, since
it does not make sense to register it as a struct net_device (UCLASS_ETH
udevice for U-Boot), because that would never be beneficial for a user:
they would not be able to use it for traffic, since conceptually, a
packet delivered to the CPU port should loop back into the system.
Nonetheless, DSA has had numerous growing pains due to the lack of a
struct net_device for the CPU port, but so far it has overcome them.
It is unlikely at this stage of maturity that this aspect of it will
change.
We would like U-Boot to present the same information as Linux, to be at
parity in terms of number of interfaces, so that ethNaddr environment
variables could directly be associated between U-Boot and Linux.
Therefore, we would implicitly like U-Boot to hide the CPU port from the
user as well.
But the paradox is that DSA still needs a struct phy_device to inform
the driver of the parameters of the link that it should configure the
CPU port to. The problem is that the phy_device is typically returned
via a call to phy_connect, which needs an udevice to attach the PHY to,
and to search its ofnode for the 'fixed-link' property. But we don't
have an udevice to present for the CPU port.
Since 99% of DSA setups are MAC-to-MAC connections between the switch
and the host Ethernet controller, the struct phy_device is going to be a
fixed PHY. This simplifies things quite a bit. In U-Boot, a fixed PHY
does not need an MDIO bus, and does not need an attached dev either.
Basically, the phy_connect call doesn't do any connection, it just
creates the fixed PHY.
The proposal of this patch is to introduce a new fixed_phy_create
function which will take a single argument: the ofnode that holds this:
port@4 {
reg = <4>;
phy-mode = "internal";
fixed-link {
speed = <2500>;
full-duplex;
};
};
and probe a fixed PHY driver using the information from this ofnode.
DSA will probably be the only user of this function.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Unlike the Linux fixed PHY driver, the one in U-Boot does not attempt to
emulate the clause 22 register set of a gigabit copper PHY driver
through the swphy framework. Therefore, the limitation of being unable
to support speeds higher than gigabit in fixed-link does not apply to
the U-Boot fixed PHY driver. This makes the fixed-link U-Boot
implementation more similar to the one from phylink, which can work with
any valid link speed.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
This adds support for RPC test trusted application emulation, which
permits to test reverse RPC calls to TEE supplicant. Currently it covers
requests to the I2C bus from TEE.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
This commit gives the secure world access to the I2C bus so it can
communicate with I2C slaves (typically those would be secure elements
like the NXP SE050).
A similar service implementation has been merged in linux:
c05210ab ("drivers: optee: allow op-tee to access devices on the i2c
bus")
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
At present this function does not accept a size for the FIT. This means
that it must be read from the FIT itself, introducing potential security
risk. Update the function to include a size parameter, which can be
invalid, in which case fit_check_format() calculates it.
For now no callers pass the size, but this can be updated later.
Also adjust the return value to an error code so that all the different
types of problems can be distinguished by the user.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Bruce Monroe <bruce.monroe@intel.com>
Reported-by: Arie Haenel <arie.haenel@intel.com>
Reported-by: Julien Lenoir <julien.lenoir@intel.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
As this is the last SH4A board, remove that support as well.
Cc: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM by the deadline of v2020.01
and is missing other conversions which depend on this as well. Remove it.
Patch-cc: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Patch-cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline of
v2019.04, which is almost two years ago. In addition there are other DM
migrations it is also missing. Remove it.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefano Babic <sbabic@denx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmAmOowcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyGEpB/oD2ZQdqY/kfu0SlKE6
2Qor+MSwDA8yQlAKfiX2J3x0sAaGNkeUPQrWLxutACd34MJsjG41sr6uvLwu4E9f
bc91Gk1Xv/kmySi7JPfpctb01Bd1GVpzuHELIumGgYRkNSwAFFaXrqVPxr/9cN3t
dEcfbKX0p4qXUv/TDw3tE1D63dYPIJC3yX0/4n/n824AKeqRyTMVC34rjfEOoE/r
0w6YSxwQ8hlh23xwc2tyEMSKR4jNp8mAtQcl03Gi/6xiaqgH6lQ6ardSblr3qvjW
6Ev1nd3f9d8i0CzipbLH6PL4G31Ft+ZG/Z/z8wqA6w15h29wu7CfV8yC0aBV0g0/
N1ko
=7ddr
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2021.04 cycle:
This small PR includes just two fixes but very important: one revert in
the clk subsystem which fixes the boot on many old boards
(sama5d2_xplained, sama5d4_xplained), which currently crash at boot; and
one small fix related to debug serial on sama7g5ek board.
If probe fails, the mdio bus isn't unregistered. Fix it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Revert changes in at91 compat.c that cause u-boot to fail booting on
sama5d4_xplained and sama5d2_xplained
Log below:
<debug_uart>
No serial driver found
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Could not initialize timer (err -19)
Fixes: a2703ce10c ("dm: Remove uses of device_bind_offset()")
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Linux kernel v5.7-rc1 introduced the compatible "st,stm32mp15-hsotg".
See Linux kernel commit d49850110434 ("dt-bindings: usb: dwc2: add
support for STM32MP15 SoCs USB OTG HS and FS")
This patch updates the supported compatible in DWC2 driver,
removes the add-on done in U-Boot dtsi and keeps the compatible
defined in SOC dtsi arch/arm/dts/stm32mp151.dtsi:
usbotg_hs: usb-otg@49000000 {
compatible = "st,stm32mp15-hsotg", "snps,dwc2";
reg = <0x49000000 0x10000>;
...
};
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Testing with v2021.01 on MIPS Octeon has shown, that the latest patch
for the "short packet event trb handling" did introduce a bug on
platforms with virtual address != physical address. This patch fixes
this issue by using the correct address types in the compare (both
physical in this case).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Ran Wang <ran.wang_1@nxp.com>
Cc: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Function dm_pci_map_bar() may fail and returns NULL. Check this to prevent
dereferencing a NULL pointer.
In xhci-pci this may happen when board does not enable CONFIG_PCI_PNP and
PCI_BASE_ADDRESS_0 contains unconfigured zero address.
Signed-off-by: Pali Rohár <pali@kernel.org>
Add support to disable specific ports, it's useful for some
scenarios:
1. usb3 PHY is shared whith PCIe or SATA, the corresponding
usb3 port can be disabled;
2. some usb2 or usb3 ports are not used on special platforms,
they should be disabled to save power.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The Amlogic AXG MIPI + PCIe Analog PHY provides function for both PCIe and
MIPI DSI at the same time, and provides the Analog part of MIPI DSI transmission
and Analog part of the PCIe lines.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic AXG SoCs embeds a MIPI D-PHY used to communicate with DSI
panels.
This D-PHY depends on a separate analog PHY.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the PHY configure op callback to the generic PHY uclass to permit
configuring the PHY.
It's useful for MIPI DSI PHYs to setup the link timings.
Signed-off-by:Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The MIPI D-PHY spec defines default values and boundaries for most of the
parameters it defines. Introduce helpers to help drivers get meaningful
values based on their current parameters, and validate the boundaries of
these parameters if needed.
These helpers and header are taken from Linux commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support of missing I2C6_K with bit 3 of RCC_MC_APB5ENSETR =
I2C6EN: I2C6 peripheral clocks enable.
This patch allows customer to use I2C6 in SPL or in U-Boot
as other I2C instance, already support in clk driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Bind only the enabled GPIO subnode, to avoid to probe the node
"gpio-controller" present in SOC dtsi (disabled by default) but
not enabled in the included pincontrol dtsi file.
For example, in stm32mp15xxac-pinctrl.dtsi 2 gpio bank are absent:
gpioj: gpio@5000b000
gpiok: gpio@5000c000
Then these GPIO are absent in output of command "dm tree" and
"gpio status -a"
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
OTYPE can be used for output or for alternate function to select
PP = push-pull or OP = open-drain mode, according reference manual
(Table 81. Port bit configuration table).
This patch removes this indication for input pins and adds it
for AF and output pins for pinmux command output.
Fixes: b305dbc08b ("pinctrl: stm32: display bias information for all pins")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Instead of redefining a pin's name size, use PINNAME_SIZE defined
in include/dm/pinctrl.h
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
pin-controller pin's name must be equal to pin's name used in device
tree with "pins" DT property.
Issue detected on stm32mp157c-ev1 board with goodix touchscreen.
In DT, the goodix's pin is declared in DT with the node:
goodix_pins: goodix {
pins = "gpio14";
bias-pull-down;
};
Whereas in stmfx pin-controller driver, pin's name are equal to
"stmfx_gpioxx" where xx is the pin number.
This lead to not configure stmfx's pins at probe because pins is
identified by its name (see pinctrl_pin_name_to_selector() in
pinctrl-generic.c) and stmfx pin "gpio14" can't be found.
To fix this issue, come back to the original stmfx pin's name.
Revert "pinctrl: stmfx: update pin name"
This reverts commit 38d30cdcd65c73eeefac5efa328ad444a53b77dd.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
- Espressobin: Set default env values at runtime (Pali)
- Espressobin: Set the maximum slave SPI speed to 40MHz (Pali)
- theadorable: PCIe test code enhancement and early deemphasis
enabling (Stefan)
- pci_mvebu: Disable config access to PCI host bridge ports (Stefan)
- mv_sdhci: parse device-tree entry (Baruch)
Update gpio driver to use same logic for big-endian and little-endian
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162A is not like LX2160A which has different PCIe controller
in rev1 and rev2 silicon. It supports only one configuration of
PCIe controller, which is same as LS2088A. So update PCIe
compatible string same as LS2088A.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the SVR definitions to a new svr.h for
Layerscape armv7 and armv8 platforms respectively, so that
the PCIe driver can reuse them.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1088 requires the same QUADSPI_QURIK_BASE_INTERNAL
workaround as the LS208x and also has a 64 byte TX buffer.
With the previous settings SPI-NAND reads over AHB were
corrupted.
Fixes: 91afd36f38 ("spi: Transform the FSL QuadSPI driver to use the SPI MEM API")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adapted from kernel commit b0177aca7aea
From: Michael Walle <michael@walle.cc>
Make use of a core helper to ensure the desired width is respected
when calling spi-mem operators.
Otherwise only the SPI controller will be matched with the flash chip,
which might lead to wrong widths. Also consider the width specified by
the user in the device tree.
Fixes: 91afd36f38 ("spi: Add a driver for the Freescale/NXP QuadSPI controller")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200114154613.8195-1-michael@walle.cc
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Mathew McBride <matt@traverse.com.au> [adapt for U-Boot]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Current MDIO wait time is too long, which introduce long delay when
PHY negotiation register checking. Reduce it to 10us
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fugang Duan <Fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
We have encountered circumstances when a board design does not include
pull-up resistors on the external MDIO buses which are not used. This
leads to the MDIO data line not being pulled-up, thus the MDIO controller
will always see the line as busy.
Without a timeout in the MDIO bus driver, the execution is stuck in an
infinite loop when any access is initiated on that external bus.
Add a timeout in the driver so that we are protected in this
circumstance. This is similar to what is being done in the Linux
xgmac_mdio driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Provide an explicit configuration option to disable default "unlock all"
of any flash chip which supports locking. It doesn't make sense to
automatically unprotect the entire flash on each u-boot startup if the
block protection bits are actually used.
Traditionally, the unlock was there to be able to write to flash devices
which powered-up with the block protection bits set. Over time this
feature creeped into all flash devices which support locking.
For a more detailed description and discussion see:
https://lore.kernel.org/linux-mtd/20201203162959.29589-8-michael@walle.cc/
Keep things simple in u-boot and just provide a configration option to
disable this behavior which can be set per board.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Call mmc_of_parse() so that generic DT properties like 'non-removable'
are taken into account.
This fixes boot on Clearfog with eMMC on SOM that requires the
non-removable property.
Reported-by: Thorsten Spille <thorsten_spille@netcor.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
This patch changes the PCI config routines in the Armada XP / 38x driver
to not allow access to the PCIe root ports.
While updating the Armada XP based theadorable to the latest mainline
and testing it with the DM PCI driver I noticed, that the PCI root
bridge was being configured incorrectly. Resulting in the PCIe Intel
WiFi was not working correctly in Linux. With this patch applied, all
PCIe devices work without any issues in Linux again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Mario Six <mario.six@gdsys.cc>
In case MMC has MBR system and fastboot writes GPT,
MMC is still recognized as MBR.
Invoke part_init() to purge cached data and update
information about partition table type.
Signed-off-by: Roman Stratiienko <r.stratiienko@gmail.com>
Add command oem bootbus which executes the command
``mmc bootbus <id> <arg>`` on the current fastboot mmc device
(<i> = CONFIG_FASTBOOT_FLASH_MMC_DEV) to set the eMMC boot
configuration on first update, with
<arg> = boot_bus_width reset_boot_bus_width boot_mode
$> fastboot oem bootbus:<boot_bus_width> <reset_boot_bus_width> <boot_mode>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add fastboot command oem partconf which executes the command
``mmc partconf <id> <arg> 0`` on the current <id> mmc device
to configure the eMMC boot partition with
<arg>: boot_ack boot_partition, so the command is:
$> fastboot oem partconf:<boot_ack> <boot_partition>
The partition_access argument is forced to 0 (userdata)
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
[lukma - Kconfig adjustments after merging this patch]
Update the code and the configs for eMMC boot and userdata
partitions acces
- FASTBOOT_MMC_BOOT_SUPPORT: boot partition 1 and 2 (erase/write)
- FASTBOOT_MMC_BOOT1_NAME: boot partition 1, default name="mmc0boot0"
- FASTBOOT_MMC_BOOT2_NAME: boot partition 2, default name="mmc0boot1"
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Split userdata and boot partition support for eMMC update
and correct the description (update is supported).
The new configuration CONFIG_FASTBOOT_MMC_USER_SUPPORT
allows to activate support of userdata partition update,
based on target name=CONFIG_FASTBOOT_MMC_USER_NAME
This patch also removes the unnecessary dependency with
ARCH_MEDIATEK and EFI_PARTITION.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
It is possible to implement fastboot_set_reboot_flag in a generic way
if BCB commands are turned on for a target. Using
bcb_set_reboot_reason allows to do this by simply passing string with
correct reboot reason that should be handled during next boot process.
If BCB are turned off, then bcb_set_reboot_reason would simply return
error, so it won't introduce any new behaviour for such targets.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
This reverts commit 0ebf9842e5.
Current generic implementation of fastboot_set_reboot_flag is somewhat
messy and requires some additional configuration option to be enabled
besides CMD_BCB, so it reverts that implementtion in order to bring a
new cleaner one.
Next commit introduces new generic implementation of
fastboot_set_reboot_flag.
Signed-off-by: Roman Kovalivskyi <roman.kovalivskyi@globallogic.com>
- Sync DTS from Linux kernel for all K3 platforms
- Add MMC higher speed nodes for AM65x, J721e, J7200
- Convert Nokia RX-51 to use CONFIG_DM_MMC
- Minor fixes for LEGO MINDSTORMS
Use the generic sdhci_set_control_reg() instead of duplicating
in platform driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
According to the AM654x Data Manual[1], the setup timing in lower speed
modes can only be met if the controller uses a falling edge data launch.
To ensure this, the HIGH_SPEED_ENA (HOST_CONTROL[2]) bit should be
cleared in default speed, SD high speed, MMC high speed, SDR12 and SDR25
speed modes.
Use the sdhci writeb callback to implement this condition.
[1] http://www.ti.com/lit/gpn/am6546 Section 5.10.5.16.1
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With the new SW tuning App note[1], a custom tuning algorithm is
required for eMMC HS200, HS400 and SD card UHS modes. The algorithm
involves running through the 32 possible input tap delay values and
sending the appropriate tuning command (CMD19/21) for each of them
to get a fail or pass result for each of the values. Typically, the
range will have a small contiguous failing window. Considering the
tuning range as a circular buffer, the algorithm then sets a final
tuned value directly opposite to the failing window.
[1] https://www.ti.com/lit/pdf/spract9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add support for writing new clock buffer select property for both
the am654x and j721e 4 bit IPs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
DLL need only be enabled for speed modes and clock frequencies at or
above 50 MHz. For speed modes that don't enable the DLL, we need to
configure a static input delay value. This involves reading an optional
itap-del-sel-* value from the device tree and configuring it for the
appropriate speed mode.
Therefore, move all dll configurations to their own functions and gate it
with 50 MHz speed and a minimum mode. If both these conditions are not
satisfied then configure delay chain modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Support for AM65x PG2.0. Use the SoC bus framework to fixup
the platform data and do DLL calibration if the revision is 1.0
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Not all controllers need calibration for the PHY DLL. Add a DLL_CALIB
flag to indicate the same.
Also move the write of trm_icp and driver strength to the set_clock()
function to match the kernel configuration flow.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Convert the flags field defines to use the BIT() macro.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
There are some speed modes that work without switching the dll on.
Unconditionally switch off the DLL before setting clock frequency to
support this case. The software will automatically enable DLL for speed
modes that require it. This also means the dll_on priv data member is no
longer required.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
The dm_spi_ops.xfer() API does not support dual and quad SPI modes. It
also doesn't allow the zynqmp_gqspi driver to calculate the correct
number of dummy cycles for some NOR ops (as doing so also requires the
buswidth).
Port the zynqmp_gqspi driver to spi_controller_mem_ops, which gives us
the buswidth values to correctly support all SNOR_PROTO_X_X_X commands
and to properly calculate dummy cycles.
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
CC: jagan@amarulasolutions.com
CC: michal.simek@xilinx.com
CC: Ashok Reddy Soma <ashokred@xilinx.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
sandbox_scmi_devices_ctx() may return NULL. We should not dereference this
value in sandbox_scmi_devices_remove().
The problem was indicated by 'gcc-11 -fanalyzer'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
priv->iobase was declared as phys_addr_t which is now a 64-bit
address. In a 32-bit build, this causes the following warning
seen when building ftmac100.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast priv->iobase with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
dev_read_addr() returns fdt_addr_t which is now a 64-bit address.
In a 32-bit build, this causes the following warning seen when
building serial_sifive.c:
warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Cast the return value with uintptr_t.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Add another flag to the DM core which could be assigned to drivers and
which makes those drivers call their remove callbacks last, just before
booting OS and after all the other drivers finished with their remove
callbacks. This is necessary for things like clock drivers, where the
other drivers might depend on the clock driver in their remove callbacks.
Prime example is the mmc subsystem, which can reconfigure a card from HS
mode to slower modes in the remove callback and for that it needs to
reconfigure the controller clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if device_remove() decides that the device should not actually
be removed, it still calls the uclass pre_remove() method and powers the
device down.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the uclass pre-remove method is called before the children are
removed. But the children may refused to be removed, in whch case the
uclass is in a tricky situation. At present we handle this by calling
the uclass' post_probe() method. But it seems better to avoid doing
anything with the uclass in this case.
Switch the ordering so that we make sure the children can be removed
before advising the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
This flag has the word 'REMOVE' in it which means it conflicts with
the DM_REMOVE flags. Rename it to DM_FLAG_LEAVE_PD_ON which seems to
indicate its purpose well enough.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has no useful meaning in U-Boot and will never be returned. We want
to reserve this flag for internal driver model use.
Drop the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This has no useful meaning in U-Boot. Use -ENOMEM since that appears to
be what has gone wrong in this case. We want to reserve this flag for
internal driver model use.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image
At present long delays such as msleep(2000) can cause an overflow in this
function. There is no need for this, since it already uses a 64-bit int.
Add a cast to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useless and misleading to print the ret variable that is not set
by the dev_read_addr routine. Also, move the '\n' character after the
round bracket that contains the error code.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If one of functions is not super speed capable, we need force the udc
to be high speed, this is an equivalent implementation of
usb_gadget_udc_set_speed() in kernel but simple, which set the gadget
max_speed to be high speed, so afterwards when start gadget duc can
set the HW to be USB 2.0 mode.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set its max_speed to be super speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add super speed EP config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is to add usb gadget super speed support in common
driver, including BOS descriptor and select the super speed
descriptor from function driver.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Always use the new added config for os_desc_config to fix cdev->
os_desc_config may miss set in case we restart usb gadget driver.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current way to set cdev->os_desc_config is wrong if user restart
fastboot, as the old config is not used anymore and new allocated
usb_configuration will be used, so set the os_desc_config while
usb_add_config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add device interface GUID for Microsoft Extended Properties Feature
Descriptor.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a proting patch from linux kernel: 37a3a533429e
("usb: gadget: OS Feature Descriptors support"), the original commit
log see below:
There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS Feature Descriptors", that is "Extended Compatibility ID"
and "Extended Properties".
Hosts which do request "OS descriptors" from gadgets do so during
the enumeration phase and before the configuration is set with
SET_CONFIGURATION. What is more, those hosts never ask for configurations
at indices other than 0. Therefore, gadgets whishing to provide
"OS descriptors" must designate one configuration to be used with
this kind of hosts - this is what os_desc_config is added for in
struct usb_composite_dev. There is an additional advantage to it:
if a gadget provides "OS descriptors" and designates one configuration
to be used with such non-USB-compliant hosts it can invoke
"usb_add_config" in any order because the designated configuration
will be reported to be at index 0 anyway.
This patch also adds handling vendor-specific requests addressed
at device or interface and related to handling "OS descriptors"."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As other users may use utf8_to_utf16le() to convert the utf8
to utf16 for usb, so move it to head file.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This is a porting patch from linux kernel: 19824d5eeece
("usb: gadget: OS String support"), original commit log
see below:
"There is a custom (non-USB IF) extension to the USB standard:
http://msdn.microsoft.com/library/windows/hardware/gg463182
They grant permission to use the specification - there is
"Microsoft OS Descriptor Specification License Agreement"
under the link mentioned above, and its Section 2 "Grant
of License", letter (b) reads:
"Patent license. Microsoft hereby grants to You a nonexclusive,
royalty-free, nontransferable, worldwide license under Microsoft鈥檚
patents embodied solely within the Specification and that are owned
or licensable by Microsoft to make, use, import, offer to sell,
sell and distribute directly or indirectly to Your Licensees Your
Implementation. You may sublicense this patent license to Your
Licensees under the same terms and conditions."
The said extension is maintained by Microsoft for Microsoft.
Yet it is fairly common for various devices to use it, and a
popular proprietary operating system expects devices to provide
"OS descriptors", so Linux-based USB gadgets whishing to be able
to talk to a variety of operating systems should be able to provide
the "OS descriptors".
This patch adds optional support for gadgets whishing to expose
the so called "OS String" under index 0xEE of language 0.
The contents of the string is generated based on the qw_sign
array and b_vendor_code.
Interested gadgets need to set the cdev->use_os_string flag,
fill cdev->qw_sign with appropriate values and fill cdev->b_vendor_code
with a value of their choice.
This patch does not however implement responding to any vendor-specific
USB requests."
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As the SDP protocol use the predefined ep num for communication, we can't
change its name hence reset its ep num while do ep autoconfig, this is
only apply for SPL.
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since some new fields in usb_ep structure been moved to usb_ss_ep.
The CDNS3 gadget driver should replies on this operation to bind the
usb_ss_ep with the endpoint descriptor when function layer uses
usb_ep_autoconfig to add endpoint descriptors to gadget. So that
CDNS3 driver can know the EP information and configure the EP once
the set configuration request is received.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Each array is used only in one file (core.c or ep0.c). Move their content
to correct file, mark them as static and do not export out of current file.
This change allows to decrease size of u-boot.bin as more of those strings
are not used.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reinitialize dfu_env_entities after flashing the 'SCRIPT' entity to
ensure that the potential changes to the 'dfu_alt_info' environment
variable are applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SCRIPT' type for DFU entities. The downloaded data are
treated as simple u-boot's scripts and executed with run_command_list()
function.
Flashing the 'SCRIPT' entity might result in changing the 'dfu_alt_info'
environment variable from the flashed script, so add a global variable
for tracking the potential need to reinitialize the dfu_alt_info related
structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Define a new 'SKIP' type for the DFU entities. The flashed data for that
entity is simply ignored without returning any error values.
This allows to have one flashing procedure and images for the different
board types or variants, where each board uses only the images relevant
to it and skips the rest. This is especially usefull for the THOR
protocol, which usually transfers more than one file in a single session.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
[mszyprow: rephrased commit message and docs for easier reading, changed
subject to "dfu: add 'SKIP' entity"]
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Use the default MMC device set in the command line if entity specifies it
as -1. This allows to use the same dfu_alt_info string for different MMC
devices (like embedded eMMC and external SD card if data layout is the
same on both devices).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In case of usb_add_function() failure the error path has an issue,
i.e the global pointer variable is assigned to garbage
Fix the above mentioned issue by assigning pointer to NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In case of usb_add_function() failure the error path has two issues:
- the potentially allocated structure isn't getting freed
- the global pointer variable is assigned to garbage
Fix the above mentioned issues by freeing memory and assigning NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Casting 32bit int value directly into 64bit unsigned type causes
wrong value for file size equal or larger than 2GB. Fix the wrong
file size by casting uint32_t first.
Fixes: commit 1fe9ae76b1 ("gadget: f_thor: update to support more than 4GB file as thor 5.0")
Reported-by: Junghoon Kim <jhoon20.kim@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
For UBI partitions ("partubi" in dfu_alt_info), dfu_fill_entity_mtd sets
the mtd.ubi flag; however other functions incorrectly check for nand.ubi
instead. Fix this by checking for the correct flag.
Signed-off-by: Guillermo Rodriguez <guille.rodriguez@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The R-Car3 SDHI should set these two bits in DMA_MODE register according
to the specification, to indicate 64bit bus width. No other bus width
options are permitted and the default value is 0, which is incorrect.
Set the bits accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Provide information about host backed block device.
Mark the device created by 'host bind' as removable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI Self Certification Test (SCT) checks the SetTime() service with
the following steps:
* set date
* reset
* check date matches
To be compliant the sandbox should keep the offset to the host RTC during
resets. The implementation uses the environment variable
UBOOT_SB_TIME_OFFSET to persist the offset.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this function uses the old format for reading hashes. Add
support for the current format.
Add a test while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
The use of pinctrl in the core of driver model is useful but can provoke
some strange behaviour. Add a comment to aid debugging.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current driver name does not match its compatible string, so
of-platdata does not work correctly. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
These cannot work with of-platdata since they currently need the
devicetree at runtime. Disable the emulators and the sandbox I2C driver
that needs them. We can enable these later, if needed for testing.
Switch the of_plat_parent test over to use a simple bus instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The EC can store small amounts of data for the benefit of the
verified boot process. Since the EC is seldom reset, this can allow the
AP to store data that survives a reboot or a suspend/resume cycle.
Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
