This converts the following to Kconfig:
CONFIG_ARCH_CPU_INIT
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Felix Brack <fb@ltec.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJc+lyDAAoJEB6zHgIOrC/I2MQH/A20fKVWQcnvmwwuJ8w/QNZ5
syNqpRLgw8jIMuLgmnUOQmjhKEsdcNWlESQt+eppTH2yMTSwNlQVT8SVE2s1podP
QKBSHw4V5UXlYZwZBhrrmL3twVOf6oecoE4gzpnh1ydMHiC1zcHAJuutlNw8y+ye
IVrojVPu5miN91TJuvkcGdafNdFVO4mBMhGhCFA4VN38OI6Dk/fQg4QBrxj/3XWb
+EOznxL1YZYGf8hhYqe68vMVVVT5sSq1SbId6JGHRkAYDcn/qKOuOkzW7FP7tbi/
PidcTmfqOFH1EYnincxQ1cXyhaSs/VOxRHIWgzlRIJJHHp0o7Y+FUGAilSGKHso=
=tnXy
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.07 cycle
By default the configuration of the PMC is to have an external crystal
connected that requires driving on both XIN and XOUT pins.
The bypass configuration means that only XIN will be used, the SoC will not
do any driving, and the XIN needs to be provided with a proper signal.
This is the MOSCXTBY bit in the PMC main clock generator register.
The SPL needs to properly initialize the PMC registers before switching
to external clock signal and raising the clock to the cruise speed.
Also created Kconfig for this specific configuration.
By default this is disabled.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This fixes SPL linker script size checks for 3 lds files where the size
checks were implemented as "x < YYY_MAX_SIZE".
Fix the size checks to be "x <= YYY_MAX_SIZE" instead.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
The SAMA5D2 ICP Board features the SAMA5D27 SoC,
together with QSPI Flash, Wilc3000 wireless device and
EtherCat support.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
The GARDENA smart Gateway boards are equipped with an Atmel / Microchip
AT91SAM9G25 SoC and with 128 MiB of RAM and 256 MiB of NAND storage.
This patch adds support for this board including SPL support. Therefore
the AT91Boostrap is not needed on this platform any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds _image_binary_end to the SPL linker script. This will be
used be the upcoming GARDENA AT91SAM based platform, which uses DT in
SPL and configures CONFIGURE_SPL_SEPARATE_BSS.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch enables and starts the watchdog on the AT91 platform if
configured. The WD timeout value is read in the AT91 WD device driver
from the DT, using the "timeout-sec" DT property. If not provided in
the DT, the default value of 2 seconds is used.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
This patch adds a call to spl_early_init() to board_init_f() which is
needed when CONFIG_SPL_OF_CONTROL is configured. This is necessary for
the early SPL setup including the DTB setup for later usage.
Please note that this call might also be needed for non SPL_OF_CONTROL
board, like the smartweb target. But smartweb fails to build with this
call because its binary grows too big. So I disabled it for these kind
of targets for now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
Make sure that lowlevel_init is not compiled when
CONFIG_SKIP_LOWLEVEL_INIT_ONLY is configured.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested on the taurus board:
Tested-by: Heiko Schocher <hs@denx.de>
When introducing the SAMA5D27 SoCs, the SAMA5D2 series got an additional
chip id. The check if the cpu is sama5d2 was changed from a preprocessor
definition (inlining a call to 'get_chip_id()') to a C function,
probably to not call get_chip_id twice?
That however broke a check in the macb ethernet driver. That driver is
more generic and also used for other platforms. I suppose this solution
was implemented to use it in 'gem_is_gigabit_capable()', without having
to stricly depend on the at91 platform:
#ifndef cpu_is_sama5d2
#define cpu_is_sama5d2() 0
#endif
That only works as long as cpu_is_sama5d2 is a preprocessor definition.
(The same is still true for sama5d4 by the way.) So this is a straight
forward fix for the workaround.
The not working check on the SAMA5D2 CPU lead to an issue on a custom
board with a LAN8720A ethernet phy connected to the SoC:
=> dhcp
ethernet@f8008000: PHY present at 1
ethernet@f8008000: Starting autonegotiation...
ethernet@f8008000: Autonegotiation complete
ethernet@f8008000: link up, 1000Mbps full-duplex (lpa: 0xffff)
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
BOOTP broadcast 5
BOOTP broadcast 6
BOOTP broadcast 7
BOOTP broadcast 8
BOOTP broadcast 9
BOOTP broadcast 10
BOOTP broadcast 11
BOOTP broadcast 12
BOOTP broadcast 13
BOOTP broadcast 14
BOOTP broadcast 15
BOOTP broadcast 16
BOOTP broadcast 17
Retry time exceeded; starting again
Notice the wrong reported link speed, although both SoC and phy only
support 100 MBit/s!
The real issue on reliably detecting the features of that cadence
ethernet mac IP block, is probably more complicated, though.
Fixes: 245cbc583d ("ARM: at91: Get the Chip ID of SAMA5D2 SiP")
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Make use of "IMAGE_MAX_SIZE" and "IMAGE_TEXT_BASE" rather than
CONFIG_SPL_MAX_SIZE and CONFIG_SPL_TEXT_BASE. This lets us re-use the
same script for both SPL and TPL. Add logic to scripts/Makefile.spl to
pass in the right value when preprocessing the script.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Andreas Bießmann <andreas@biessmann.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850evm & omap3_logic_somlv
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add test for the SPL binary size and the bss section size.
This will throw an error at build time if the SPL sections
do not fit in the designated RAM area, thus avoiding oversizing the SPL.
Based on original work by Wenyou Yang.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Convert the Watchdog driver for AT91SAM9x processors to support
the driver model and device tree. Changes "CONFIG_AT91SAM9_WATCHDOG"
to new "CONFIG_WDT_AT91" Kconfig option.
Signed-off-by: Prasanthi Chellakumar <prasanthi.chellakumar@microchip.com>
The interruption support had be removed for ARM architecture and
the function get_timer_masked() is no more used except in some
the timer.c files.
This patch clean each timer.c which implement this function and
remove the associated prototype in u-boot-arm.h
For timer.c, I don't verify if the weak version of get_timer
(in lib/time.c) can be used
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The interruption support had be removed for ARM architecture and
the function udelay_masked() is no more used except in some timer.c
files and have the same content than udelay() or __udelay().
This patch update each timer.c implementing this function and
remove the associated prototype in u-boot-arm.h.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Call the PDA detection mechanism at boot time so we can have
the pda environment variable ready for use.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Four different boards had different options for enabling cache
that were virtually all the same. This consolidates these
common functions into arch/arm/cpu/arm926ejs/cache.c
This also has the positive side-effect of enabling cache on
the Davinci (da850) boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add mach-at91 to the list of consolidations]
Signed-off-by: Tom Rini <trini@konsulko.com>
CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Fix Kconfig bool, default, select and imply options to be
alphabetically sorted.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
- spl_board_init is empty on smartweb so drop that function
- When CONFIG_AT91SAM9_WATCHDOG is set we do not disable the watchdog in
SPL and instead let full U-Boot handle it. Instead of an empty
function just do not call a function.
Signed-off-by: Tom Rini <trini@konsulko.com>
When a pin is muxed to a peripheral or as a GPIO, the only
configuration that can be set is the pullup. It is too restrictive
so this patch allows to give a full configuration.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPI
This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
AT91 ma5d4evk board uses atmel spi driver, enable DM_SPI to
use dm functionality.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable Driver model for AT91 Vinco boards.
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Enable DM_SPI for atmel SPI driver on taurus board.
Kept few functions related to non-dm and gpio on board
files for reference and will be remove once code moved
to relevant drivers.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add USB clock driver to configure the input clock and the divider
in the PMC_USB register to generate a 48MHz and a 12MHz signal to
the USB Host OHCI.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.
The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.
To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This board is based on the Atmel sama5d3 eval boards.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
This board is based on the Atmel 9x5 eval board.
Supporting the following features:
- Boot from NAND Flash
- Ethernet
- FIT
- SPL
Signed-off-by: Ben Whitten <ben.whitten@lairdtech.com>
Signed-off-by: Dan Kephart <dan.kephart@lairdtech.com>
Add the SAMA5D2 PTC EK board and remove the SAMA5D2 PTC ENGI board
which was a prototype.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add a header for SAMA5D2 SMC since it's not compatible with
SAMA5D3 one.
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
[wenyou: fix the wrong base address of the SMC register]
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Last user of this option went away in commit:
fdc7718999 ("board: usb_a9263: Update to support DT and DM")
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert the board to support the video driver model, add the device
tree node, and remove the unnecessary code.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the CONFIG_XXXX_BOOT to indicate the boot media, instead of
the CONFIG_SYS_USE_XXXX option, which is declared by
CONFIG_SYS_EXTRA_OPTIONS option.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
As said in READRE.kconfig, include/configs/*.h will be removed
after all options are switched to Kconfig. As the first step,
remove the follow line from include/configs/*.h.
#include <asm/hardware.h>
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
To prepare to remove the SoCs options such as SAMA5D2, SAMA5D3
and SAMA5D4 from the CONFIG_SYS_EXTRA_OPTIONS option which is
deprecated, add the SoC options to Kconfig.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
The SAMA5D27-SiP (System in Package) integrates the SAMA5D2
with 1Gbit DDR2-SDRAM in a single package.
The SAMA5D27 SOM1 embeds a 64Mbit QSPI flash, KSZ8081 Phy and
Mac-address EEPROM.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SAMA5D2 SiP(System in Package) has different Chip IDs in the
CHIPID and CHIP_EXID registers.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the boot device for booting from the QSPI flash.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Refer to the commit 70f8c8316ad(PMC: add new mck function to lower
rate while switching) from AT91Bootstrap.
While switching to a lower clock source, we must switch the clock
source first instead of last. Otherwise, we could end up with
too high frequency on internal bus and peripherals.
This happens on SAMA5D2 as exitting from the ROM code.
Add a function pmc_mck_init_down() to allow this sequence.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As said in 29.5.7 section of SAMA5D2 datasheet, before switching to
the crystal oscillator, a check must be carried out to ensure that
the oscillator is present and that its freqency is valid.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a function to display the company's logo and board information
via the API from DM_VIDEO. This function can be shared by other
atmel boards, so locate it in board/atmel/common folder.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
By default, it is assumed that the UTMI clock is generated from
a 12 MHz reference clock (MAINCK). If it's not the case, the FREQ
field of the SFR_UTMICKTRIM has to be updated to generate the UTMI
clock in the proper way.
The UTMI clock has a fixed rate of 480 MHz. In fact, there is no
multiplier we can configure. The multiplier is managed internally,
depending on the reference clock frequency, to achieve the target
of 480 MHz.
The patch is cloned from the patch of mailing-list:
[PATCH v2] clk: at91: utmi: set the mainck rate
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
[trini: Depend on SPL_DM]
Signed-off-by: Tom Rini <trini@konsulko.com>
Create board/$(VENDOR)/common folder to accommodate the common code
shared by other atmel boards, now put the code to set ethernet mac
address from eeprom, which uses the i2c eeprom driver.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The MMC SPL locates the BSS section to a different memory region
from text, then use "_image_binary_end" variable to point to the
correct device tree location.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Because the MMC SPL puts the bbs section in the ddr memory, move
calling mem_init() before calling spl_init().
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
When OF_CONTROL is enabled, MMC boot device should not be detected
automatically, it should be MMC1 fixedly only the status "enabled"
is available.
Add NAND Flash boot device as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
AT91 PIO controller is a combined gpio-controller, pin-mux and
pin-config module. The peripheral's pins are assigned through
per-pin based muxing logic.
Each SoC will have to describe the its limitation and pin
configuration via device tree. This will allow to do not need
to touch the C code when adding new SoC if the IP version is
supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the CONFIG_ATMEL_LEGACY is undefined, according to the following
defines, at91_set_gpio_value() references to at91_set_pio_value(x, y)
with two parameters.
#define at91_set_gpio_value(x, y) at91_set_pio_value(x, y)
#define at91_get_gpio_value(x) at91_get_pio_value(x)
But there isn't the implementation of at91_set_pio_value(x, y) with
two parameters in U-Boot. This is an error.
Same as at91_get_gpio_value(x) define.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons. We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode. So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This option should not really be user selectable. Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
add at least icache support for at91 based boards.
This speeds up NOR flash access on an at91sam9g15
based board from 15.2 seconds reading 8 MiB from
a SPI NOR flash to 5.7 seconds.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
on at91sam9x5 PRES offset is 4 in the PMC master
clock register.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Andreas Bießmann <andreas@biessmann.org>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to make these PIO4 definitions shared with AT91 PIO4
pinctrl driver, move them from the existing gpio driver to the
head file, and rephrase them.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch is referred to at91 clock driver of Linux, to make
the clock node descriptions in DT aligned with the Linux's.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
add DM and DTS support for the at91 based siemens
boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[rebased on current ToT]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Since the spl_boot_mode() is now passed the boot device to boot from,
make use of it instead of inquiring for the boot device again. This
allows board_boot_order() to function correctly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The SPL code already knows which boot device it calls the spl_boot_mode()
on, so pass that information into the function. This allows the code of
spl_boot_mode() avoid invoking spl_boot_device() again, but it also lets
board_boot_order() correctly alter the behavior of the boot process.
The later one is important, since in certain cases, it is desired that
spl_boot_device() return value be overriden using board_boot_order().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[add newly introduced zynq variant]
Signed-aff-by: Andreas Bießmann <andreas@biessmann.org>
Add missing parenthesis around the variable into the macro.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Extend the boot device autodetection from SAMA5D2 only to the entire
SAMA5Dx family of microcontrollers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[minor compile fix for SAMA5D2]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
This board is based on Snapper 9G45 which has an Atmel AT91SAM9G45 chip and
128MB of SDRAM. It includes a small LCD, 2xUSB host, SD card, Ethernet and
two UARTs.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
[apply CONFIG_BOOTDELAY transition]
Signed-off-by: Andreas Bießmann <andreas@biessmann.org>
Add these definitions so that GPIOs can be used with driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-on: smartweb, corvus, taurus, axm
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add register definitions for the AT91 RTC so that this can potentially be
used in U-Boot.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This is available on AT91SAM9G45. Add the peripheral address and flag
definitions.
Signed-off-by: Andre Renaud <andre@designa-electronics.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Implement support for saving ARM register R4 early during boot using
save_boot_params . Implement support for decoding the stored register
R4 value in spl_boot_device() to obtain boot device from which the
SoC booted. This way, the SPL will always load U-Boot from the same
device from which the SPL itself booted instead of using hard-coded
boot device.
This functionality is useful for example when booting sama5d2-xplained
from SD card, where by default the SPL would try loading the U-Boot
from eMMC and fail. This is because eMMC is on SDHCI0 (BOOT_DEVICE_MMC1),
while SD slot is on SDHCI1 (BOOT_DEVICE_MMC2) and the SPL was hard-wired
to always boot from BOOT_DEVICE_MMC1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Add the UPLL clock and master clock as a clock source for getting
the generated clock frequency to complete its clock sources support.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Before enabling a generated clock whose source is from the UPLL
clock, check and enable the UPLL clock.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The board supports following features:
- Boot media support: NAND Flash/SPI Flash
- Support ethernet
- Support USB mass storage
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Starting with 96e5b03 we use a linker list for partition table
information. However since we use this in SPL we need to make sure that
the SPL linker scripts include these as well. While doing this, it's
best to simply include all linker lists to future proof ourselves.
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The Versatile Industrial Communication platform is a community oriented
board from Landis + Gyr. It comes with:
- an RS-485 port
- 2 Ethernet ports
- a wireless M-BUS
- a 4G modem
- a 4MB SPI flash
- a 4GB eMMC
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[rebase on current TOT]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The SAMA5D2 has a second internal SRAM that can be reassigned as a L2
cache memory.
Make sure it is configured as a L2 cache memory when booting from a SPL
image.
Based on the commit b5ea95ef2b5b from the at91bootstrap repository.
Signed-off-by: Samuel Mescoff <samuel.mescoff@mobile-devices.fr>
Reviewed-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for DENX MA5D4 SoM and MA5D4EVK board, based on the
Atmel SAMA5D4 SoC. The SoM contains the SoC, eMMC, SPI NOR, SPI
CAN controllers and DRAM, the baseboard contains UART connectors,
ethernet port, microSD slot, LCD header, 2x CAN connector and a
lot of expansion headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the PMC_PLLICPR init function, use this
function to clean up the code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To avoid the duplicated code, add the PMC_PLLICPR init function.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To avoid the duplicated code, add the PLLB handle functions.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
[add enable/disable functions to arm920t]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the UTMI PLL enable function, use this function
to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To avoid the duplicated code, add the UTMI PLL handle functions,
and add PMC_USB init function too.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to clean up the duplicated code.
Meanwhile, remove unneeded header file include, at91_pmc.h.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[fixup for arm920t code]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
To reduce the duplicated code, add a new file to accommodate
the peripheral's and system's clock handle code, shared with
the SoCs with different ARM core.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The sama5d2 Xplained SPL supports the boot medias: spi flash
and SD Card.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To remove the unnecessary #ifdef-endif, use the mpddrc IP version
to check whether or not the interleaved decoding type is supported.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The DDR3-SDRAM initialization sequence is implemented in
accordance with the DDR3-SRAM/DDR3L-SDRAM initialization section
described in the SAMA5D2 datasheet.
Add registers and definitions of mpddrc controller, which is used
to support DDR3 devices.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add struct atmel_mpddrc_config to accommodate the mpddrc register
configurations, not using the mpddrc register map structure,
struct atmel_mpddrc, in order to increase readability and reduce
run-time memory use.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To make saic redirect code sharing with other SoCs, move the
saic redirect code from SAMA5D4 particular file,
mach-at91/armv7/sama5d4_devices.c to a separate file,
mach-at91/atmel_sfr.c
Move ATMEL_SFR_AICREDIR_KEY definition to sama5d4.h, because each
SoC has its own value.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To make matrix initialization code sharing with others,
use the matrix slave id macros, instead of hard-coding.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Remove the security peripheral select code, keep the default value
in these registers, that is, the peripheral address space is
configured as "Secured" access, it is suitable for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
On processor reset, the matrix write protection is disabled,
so no need to disable/enable write protection when writing
the matrix registers.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
To make the matrix initialization code sharing with other SoCs,
move it from SAMA5D4 particular file,
mach-at91/armv7/sama5d4_devices.c to a separate file,
mach-at91/matrix.c
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The SDHCI is introduced by sama5d2, named as Secure Digital Multimedia
Card Controller(SDMMC). It supports the embedded MultiMedia Card (e.MMC)
Specification V4.41, the SD Memory Card Specification V3.0, and the SDIO
V3.0 specification. It is compliant with the SD Host Controller Standard
V3.0 specification.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some peripherals may need a second clock source that may be different
from the system clock. This second clock is the generated clock (GCK)
and is managed by the PMC via PMC_PCR.
For simplicity, the clock source of the GCK is fixed to PLLA_CLK.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Provide the specific addresses for the Chip ID and Chip ID Extension
registers, instead of the offset, which make it use on other chips.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
crt0.S do both memset the bss section and call board_init_r for us, so
remove them from board_init_f().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
These boards have not been converted to generic board by the deadline.
Remove all cpu9260 and cpuat91 boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 << 2).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch enables building SPL without
CONFIG_SPL_SERIAL_SUPPORT support.
Signed-off-by: Heiko Schocher <hs@denx.de>
[trini: Ensure we build arch/arm/imx-common on mx28]
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove board support for afeb9260, tny_a9260, and sbc35_a9g20.
They have not been converted into Generic Board yet.
See doc/README.generic-board for details.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
By making the board selections optional, every defconfig will include
the board selection when running savedefconfig so if a new board is
added to the top of the list of choices the former top's defconfig will
still be correct.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
Supports boot up from NAND flash with software ECC eanbled.
And supports boot up from SD/MMC card with FAT file system.
As the boot from SD/MMC card with FAT file system, the BSS
segment is too big to fit into SRAM, so, use the lds to put
it into SDRAM.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Config MCKR according to the datasheet sequence, or else it
will cause the MCKR configuration failed.
Remove timeout checking for clock configuration, if configure
the clock failed, let the system hang while not run in wrong
clock configuration.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
To facilitate changing lowlevel_init to become s_init, move the current
contents of s_init into board_init_f and add the rest of what
board_init_f does here.
In order to compile clean without CONFIG_SKIP_LOWLEVEL_INIT set, leave an
empty stub of s_init(). It can be removed when lowlevel_init becomes s_init.
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Matt Porter <mporter@konsulko.com> on sama5d3_xplained
Signed-off-by: Tom Rini <trini@ti.com>
[rebased on current master, leave s_init() as empty stub]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The commit 8dfafdd (Introduce common timer functions), add common
timer functions, we can use them directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[rebase on current master]
Sigend-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As the u-boot-spl.lds is used only for armv7 SoCs (includes
sama5d3 and sama5d4), so move it to armv7 directory.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
