This converts the following to Kconfig:
CONFIG_SYS_IMMR
We do this by consolidating the SYS_IMMR options we have and providing
defaults.
We also, in the few places where M68K was also sharing code with these
platforms, define it within the file to CONFIG_SYS_MBAR to match usage.
This should be cleaned up longer term.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_DRIVER_ECC_LAYOUT
In order to do this conversion, expose this option to the user and
use "save" not "safe" in the text.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_FSL_IFC
This is done via select statements to match previous logic.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_SPI_BUS
CONFIG_ENV_SPI_CS
CONFIG_ENV_SPI_MAX_HZ
CONFIG_ENV_SPI_MODE
As part of this, we use Kconfig to provide the defaults now that were
done in include/spi_flash.h. We also in some cases change from using
CONFIG_ENV_SPI_FOO to CONFIG_SF_DEFAULT_FOO as those were the values in
use anyhow as ENV was not enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
This is a "hex" prompt but the default value was given as an int.
Switch the default to hex (0x0) and remove the defconfigs that were
using the default, but as hex before.
Signed-off-by: Tom Rini <trini@konsulko.com>
If clk_get_by_name() returns 0 it means it executed successfully while now
we consider it as an error. So let's check if return value is negative to
be an error. Otherwise this prevents "axi" and "disp_axi" to be enabled.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Enable this for boards with a display, unless they are using the SPLASH
feature.
This shows a U-Boot logo on boards with a display, which seems like a
useful thing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Show the U-Boot logo by default. This is only 7KB in size so seems like
a useful default for boards that enable a display.
If SPLASH_SCREEN is enabled, it is not enabled by default, so as not to
conflict with that feature.
Also disable it for tests, since we don't want to complicate the output.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver is obsolete and only used by nokia_rx51. It should be deleted.
For now, drop the VIDEO_LOGO code to avoid confusion with the new
implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_VIDEO_LOGO
Note that this option depends on CONFIG_DM_VIDEO now, since cfb_console is
deprecated. The only relevant code is now in splash.c
Drop the check for DM_VIDEO in that file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this uses RGB555 format for blitting to a display. Sandbox uses
565 and that seems to be more normal for BMP as well. Update the code
accordingly and add a test.
Note that this likely breaks the theadorable board so we may need to
discuss supporting both formats.
Signed-off-by: Simon Glass <sjg@chromium.org>
Update this code to use write_pix8() rather than writing the pixels only
for a single supported display depth. This allows us to support any
depth.
Add some more tests too.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the code that writes to a pixel is quite convoluted. It uses a
colour map which is in the uclass and the same code is repeated in
different places within video_bmp_display().
As a first step, create a function which can write a pixel from the
bitmap, no matter what the display depth. Use any provided palette
directly, rather than using the uclass version.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a few more tests for BMP rendering. Use a back door into the sandbox
SDL driver to adjust the resolution at runtime.
The truetype code does not support 8bpp. Add this so that the display is
not blank when running in this mode.
Signed-off-by: Simon Glass <sjg@chromium.org>
The intention is for the copy base to start halfway through the
frame-buffer area. At present is it actually below the frame buffer,
which could have anything in it (probably it is malloc space). Fix
this.
Signed-off-by: Simon Glass <sjg@chromium.org>
If U-Boot starts with the frame buffer set to 16bpp but then runs a test
that uses 32bpp, there is not enough space. Update the driver to use the
maximum possible frame-buffer size, to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
When unit tests are run they currently create a new window. Update the
code so that the old one is removed first. This avoids the confusion as to
which one is active.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present sandbox only supports 16 and 32bpp depths, since those are the
easy ones with SDL.
We can support other depths by manually converting the pixel formats. Add
support for this, to enable an 8ppp (monochrome) format.
Signed-off-by: Simon Glass <sjg@chromium.org>
The watchdog system reset driver can reboot the device but it cannot power
it off. If power off is requested, the driver should not reset the system
but leave powering off to one of the other system reset drivers.
As power cycling is typically not a feature of a watchdog driver the reset
types SYSRESET_POWER and SYSRESET_POWER_OFF shall both be excluded.
Fixes: 17a0c14164 ("dm: sysreset: add watchdog-reboot driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The global data pointer is not used in this driver, remove it's
declaration.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Use more appropriate resource_size() function when working with data in
struct resource.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Function mvebu_pcie_setup_wins() sets up all other BARs, so move setup of
BAR[0] to this function to have common code at one place.
In the past, commit 193a1e9f19 ("pci: pci_mvebu: set BAR0 after memory
space is set") moved setup of BAR[0] to another location, due to ath10k
not working in kernel, but the reason why was unknown, but it seems to
work now, and we think the issue then was cause by the PCIe Root Port
presenting itself as a Memory Controller and therefore U-Boot's code
have overwritten the BAR. Since the driver now ignores any write
operations to PCIe Root Port BARs, this should not be an issue anymore.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Testing on Armada XP with an EEPROM using register address with size
of 2 has shown, that the register address bytes are sent to the I2C
EEPROM in the incorrect order. This patch swabs the address bytes so
that the correct address is transferred to the I2C device.
BTW: This worked without any issues before migrating Armada XP to
DM I2C.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Samuel Holland <samuel@sholland.org>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Pali Rohár <pali@kernel.org>
Cc: Marek Behún <marek.behun@nic.cz>
Tested-by: Marek Behún <marek.behun@nic.cz>
There is no maintainer entry for serial_mvebu_a3700.c. Add entry with Pali
and Stefan as maintainers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no maintainer entry for pci-aardvark.c. Add entry for
pci-aardvark.c and pci_mvebu.c with Pali and Stefan as maintainers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Convert A3720 common PHY driver to official DT bindings.
This puts us closer to be able to synchronize A3720 device-trees with
those from Linux.
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Konstantin Porotchkin <kostap@marvell.com>
Cc: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Marcin Wojtas <mw@semihalf.com>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Since no one uses this feature and I am not aware of any parsers of this
in Linux, remove it.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Michael Walle <michael@walle.cc>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace fdt_alloc_phandle() with subsequent fdt_set_phandle() by
fdt_create_phandle().
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
No functional change intended. This patch switches from the legacy I2C
API to the DM I2C API, so that this code can be used with DM I2C
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
This function will be commonly used in block device drivers
in the succeeding patches.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmG8PNIcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyN4NCACbdi5EFjoNkGhCWLIX
SobXNcBGaL9Zpr5qZq77uFqFeFPeiAClk9X+TcSHhBTSWPugzNCdXEdENEGdiiOR
Yxe/QvBL7ZsKkhGBw5W8sb81NBPlpnVY7DWufjYvWq7S3C3bIDahQpCeWHKXDO0H
ZzIX1413kfHRKsAIT+IbufmC1dcWY8SWQEArSkL2KhTQyHnLVGAaholgEGXoKMoC
0ACXO+uhqaAY0/1eWvvYjcfotlz881ROajSRITh+Gu0UuHyRr2Fvj7jZvF5E4Q4f
Cu8iciDsimYSDGLZsOJjPIDTfsx9jbA8IcYIAMxOLW8OYbIL6QAUKsJ2LLKao1q5
SYXP
=YXsB
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.04-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.04 cycle:
This feature set includes : support for the new QSPI hardware on
sama7g5, small fixes on sam9x60 and sama7g5, some additions of commands
and PIO controller on sam9x60/sam9x60ek.
Double peripheral RBF configuration are needed on some devices or boards
to stabilize the IO configuration system.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Sin Hui Kho <sin.hui.kho@intel.com>
Reviewed-by: Tien Fong Chee <tien.fong.chee@intel.com>
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
-----BEGIN PGP SIGNATURE-----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=1L3q
-----END PGP SIGNATURE-----
Merge tag 'clk-2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-clk
Clock patches for v2022.01-rc3
This adds better logging support for many CCF drivers, and clarifies some
documentation regarding clk_get_rate.
Define LOG_CATEGORY to allow filtering with log command
for generic clock and CCF clocks.
This patch also change existing printf, debug and pr_ macro
to log_ or dev_ macro.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reorder include files in the U-Boot expected order:
the common.h header should always be first,
followed by other headers in order,
then headers with directories,
then local files.
It is a preliminary step for next patch.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
PCI Bridge which represents aardvark PCIe Root Port has Expansion ROM Base
Address register at offset 0x30 but its meaning is different than PCI's
Expansion ROM BAR register. Only address format of register is same.
In reality, this device does not have any configurable PCI BARs. So ensure
that write operation into BARs (including Expansion ROM BAR) is noop and
registers always contain zero address which indicates that bars are
unsupported.
Fixes: cb056005dc ("arm: a37xx: pci: Add support for accessing PCI Bridge on root bus")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The PCI Bridge which represents mvebu PCIe Root Port has Expansion ROM
Base Address register at offset 0x30 but its meaning is different that
of PCI's Expansion ROM BAR register, although the address format of
the register is the same.
In reality, this device does not have any configurable PCI BARs. So
ensure that write operation into BARs (including Expansion ROM BAR) is a
noop and registers always contain zero address which indicates that BARs
are unsupported.
Fixes: a7b61ab58d ("pci: pci_mvebu: Properly configure and use PCI Bridge (PCIe Root Port)")
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Since u32 takes up 4 bytes, we need to divide the number of u32s by 4
for cfgcache.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The RZ/G2 series uses an external clock as a reference to the AVB.
If this clock is controlled by an external programmable clock,
it must be requested by the consumer or it will not turn on.
In order to do this, update the driver to use bulk enable and
disable functions to enable clocks for boards with multiple clocks.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add a block driver which handles read/write for EFI block devices. This
driver actually already exists ('efi_block') but is not really suitable
for use as a real U-Boot driver:
- The operations do not provide a udevice
- The code is designed for running as part of EFI loader, so uses
EFI_PRINT() and EFI_CALL().
- The bind method probes the device, which is not permitted
- It uses 'EFI' as its parent device
The new driver is more 'normal', just requiring its platform data be set
up in advance.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UCLASS_EFI_LOADER is used for devices created by applications and
drivers loaded by U-Boots UEFI implementation.
This patch provides a new uclass (UCLASS_EFI_MEDIA) to be used for devices
that provided by a UEFI firmware calling U-Boot as an EFI application.
If the two uclasses can be unified, is left to future redesign.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
These names are better used for access to devices provided by an EFI
layer. Use EFI_LOADER instead here, since these are only available in
U-Boot's EFI_LOADER layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
sama7g5 QSPI has:
1/ One Octal Serial Peripheral Interfaces (QSPI0) Supporting Up to
200 MHz DDR. Octal, TwinQuad, Hyperflash and OctaFlash Protocols Supported
2/ One Quad Serial Peripheral Interfaces (QSPI1) Supporting Up to
90 MHz DDR/133 MHz SDR
The QSPI controller of SAMA7G5 uses different clock domains, hence extra
synchronization operations must be performed before accessing some
registers. Differentiate between the versions of the IP using has_gclk.
Differentiate between QSPI0 and QSPI1 with has_octal.
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This is not needed anymore. Drop it to simplify the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
CONFIG_SYS_ATA_PORT_ADDR is not used in the code anymore. Drop it and use
ATA_PORT_ADDR() locally instead.
Drop CONFIG_IDE_RESET_ROUTINE and CONFIG_IDE_SWAP_IO which are also
unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can go in the related header file. Drop the CONFIG option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
* fixes the bug in function bind_drivers_pass that for
CONFIG_CC_OPTIMIZE_FOR_SIZE=n and no entries in the driver_info list,
i.e. n_ents == 0, the processor steps into the first loop iteration
despite the loop condition being false.
* the Xilinx Zynq-7000 device would eventually hang due to an attempted
access to an invalid memory address
* the bug is fixed by changing the type of idx from uint to int
Board: zynq-zybo
Target: ARM
Compiler: arm-none-eabi-gcc 9.2.1
Signed-off-by: Alexander Preissner <fpga-garage@preissner-muc.de>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Add I2C driver code for the Microchip PolarFire SoC.
This driver supports I2C data transfer and probe for I2C
slave addresses.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Remove the microchip compatible string and default compatible "cdns,macb"
support both 32-bit and 64-bit DMA access.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Enable DWC IP clock in driver probe, so the MII access is possible even
outside of active network transfers. This is particularly useful when
using 'mii' or 'mdio' commands to explore PHY state, neither of which
works with DWMAC currently due to the disabled clock.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The gpio_request_by_name() returns zero in case of success, however the
conditional return value check in gpio_request_by_name() checks only for
(ret != -ENOENT) and if the condition is true, returns ret outright.
This leads to a situation where successful gpio_request_by_name() return
leads to immediate successful eth_phy_of_to_plat() return as well, and
to skipped parsing of "reset-assert-us" and "reset-deassert-us", so the
PHY driver operates with valid reset GPIO, but with assert/deassert times
set to default, which is 0, instead of the values from DT. This breaks
PHY reset.
Fix this by checking if return value is non-zero and then for this one
single allowed non-zero return value, -ENOENT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Broadcom bnxt L2 driver support. Used by the Broadcom
iproc platforms.
Signed-off-by: Bharat Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Roman Bacik <roman.bacik@broadcom.com>
It turns out that in custom designs if the system is reset
multiple times in conjunction with a slight increase in external
temperature, the felix switch starts to behave in a strange way:
packets are no longer received on the ENECT interface connected
to the L2switch internal port (the TX side of internal port stops working
or the packets do not reach there. It is not very clear where
the packets remain blocked. None of the counters points to a disruption
in the L2switch)
The issue is not reproducible on NXP reference designs.
It was observed that by adding the switch core reset, the problem
goes aways, even if intensive testing in temperature chambers
is applied.
The current patch performs soft reset on the switch core to ensure proper
operation of the L2switch.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
This symbol is not used anywhere in the code. Just enable in couple of
defconfigs but it does nothing that's why remove it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Wait for the read/write transfer finish bit get actually cleared,
this does not happen immediately on at least SoCFPGA Gen5.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cc: Vignesh R <vigneshr@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Add a message on probe in driver model core when the default
pinctrl selection failed.
This message is displayed only when the pinctrl API is
implemented, i.e. when result is not ENOSYS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_BR0_PRELIM
CONFIG_SYS_OR1_PRELIM
CONFIG_SYS_BR1_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR2_PRELIM
CONFIG_SYS_OR2_PRELIM
CONFIG_SYS_BR3_PRELIM
CONFIG_SYS_OR3_PRELIM
CONFIG_SYS_BR4_PRELIM
CONFIG_SYS_OR4_PRELIM
CONFIG_SYS_BR5_PRELIM
CONFIG_SYS_OR5_PRELIM
CONFIG_SYS_BR6_PRELIM
CONFIG_SYS_OR6_PRELIM
CONFIG_SYS_BR7_PRELIM
CONFIG_SYS_OR7_PRELIM
This also introduces CONFIG_SYS_BR0_PRELIM_BOOL as not all platforms
that can set these values do so. Add the relevant SYS_BRx_PRELIM_BOOL
to platforms that had not been previously migrated.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the commit f42045b2e7 ("stm32mp15: replace CONFIG_TFABOOT when
it is possible") the function stm32mp1_ddr_setup is always called so the
__maybe_unused can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Compute the DDR size from DDR controller register (mstr and addrmap)
in U-Boot proper as the DDR information are useful only for SPL
but not for U-Boot proper, for example with TFABOOT.
This patch simplify U-Boot DT when several DDR size are supported
and support of next SOC in STM32MP family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Align the framebuffer size on MMU_SECTION_SIZE in kernel, = max 2MB for
LPAE for armV7, to avoid issue with the simple frame buffer activation,
when U-Boot add a reserved memory in the kernel device tree to preserve
the splash screen until Linux driver initialization.
See Linux documentation for details:
Documentation/devicetree/bindings/display/simple-framebuffer.yaml
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the helper function video_is_active() to test if one video device
is active.
This function can be used in board code to execute operation
only when the display is probed / really used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Remove the DDR interactive command tuning, as the support of a predefined
DDR PHY tuning is removed for STM32MP1 driver in SPL and in TF-A
and the result of this tuning will be never used.
Moreover this SW tuning procedure can failed on some hardware
configuration (to many BIST errors and no convergence); it will be no
more supported in the next delivery of the DDR utilities included in
the CubeMX tool of STMicroelectronics.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The support of a predefined DDR PHY tuning result is removed for
STM32MP1 driver because it is not needed at the supported frequency
when built-in calibration is executed.
The calibration parameters were provided in the device tree by the
optional node "st,phy-cal", activated in ddr helper file by the
compilation flag DDR_PHY_CAL_SKIP and filled with values generated
by the CubeMX DDR utilities.
This patch
- updates the binding file to remove "st,phy-cal" support
- updates the device trees and remove the associated defines
- simplifies the STM32MP1 DDR driver and remove the support of
the optional parameter "st,phy-cal"
After this patch, the built-in calibration is always executed
and the calibration registers are moved in the phy dynamic part;
that allows manual tests.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the read data eye training = training for optimal read valid placement
(RVTRN) when the built-in calibration is executed for LPDDR2 and LPDDR3.
This training is supported on the PUBL integrated in the STM32MP15x
DDR subsystem and it is not required for DDR3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for testing whether bus voltage level translator is present
and operational. This is useful on systems where the bus voltage level
translator is optional, as the translator can be auto-detected by the
driver and the feedback clock functionality can be disabled if it is
not present.
The translator test sets CMD high to avoid interfering with a card, and
then verifies whether signal set on CK is detected on CKIN. If the signal
is detected, translator is present, otherwise the CKIN feedback clock are
disabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Yann Gautier <yann.gautier@foss.st.com>
tpm_tis_remove() leads to calling tpm_tis_ready() with the IO region
unmapped and chip->locality == -1 (locality released). This leads to a
crash in mmio_write_bytes().
The patch implements these changes:
tpm_tis_remove(): Unmap the IO region after calling tpm_tis_cleanup().
tpm_tis_cleanup(): Request locality before IO output and releasing
locality.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Sometimes UART stops transmitting characters after UART clock is changed
back to XTAL. In this state UART fifo is always full. Kernel during early
boot wants to print output on UART and is waiting for non-empty UART fifo.
Which leads to CPU hangup without any (debug) output on UART.
Marvell Armada 3700 Functional Specifications says that for programming
fractional divisor registers it is required to disable UART, enable
loopback mode, reset fifos, program registers, disable loopback mode,
release reset of fifos and enable UART.
But these steps do not fix above mentioned issue that UART hangup. Also
gating UART clock does not help. And even resetting UART state machines do
not help.
Experiments showed that UART fifo is unblocked after board is being reset
(during board reset UART HW transmit UART fifo even CPU is not executing
kernel/bootloader anymore).
And another experiments showed that same workaround can be achieved also
by external reset of UART HW (without need to reset board).
So do not implement any of "Marvell recommended" steps from Functional
Specifications as they do not work. And rather prior changing parent clock
back to XTAL, do external reset of UART HW. This operation also resets all
UART registers, so basically it also sets UART clock to default, which is
XTAL. It is unknown why UART hangups and enters such broken state.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add a function that returns the number of devices in a uclass. This can be
helpful in sizing an array that needs to hold a list of them.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases it is useful to search just by a partial name, such as
when looking for a sibling device that has a common name substring. Add
helper functions to handle these requirements.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we support reading a string list a string at a time. Apart
from being inefficient, this makes it impossible to separate reading of
the devicetree into the of_to_plat() method where it belongs, since any
code which needs access to the string must read it from the devicetree.
Add a function which returns the string property as an array of pointers
to the strings, which is easily used by clients.
Signed-off-by: Simon Glass <sjg@chromium.org>
The details for of_property_read_string_helper() and
ofnode_read_string_index() are a little inaccurate. Fix up the comments to
avoid confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
This method is currently called after the platform data has been freed.
But the pre_unbind() method may wish to access this, e.g. to free some
data structures stored there.
Split the unbinding of devices into two pieces, as is done with removal.
This corrects the problem.
Also tidy a code-style issue in device_remove() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the MMC uclass assumes that the only child it can have is a
block device. Update this so we can add a bootmethod too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Provide a way for sandbox MMC to present data from a backing file. This
allows a filesystem to be created on the host and easily served via an
emulated mmc device.
Signed-off-by: Simon Glass <sjg@chromium.org>
This change implements an SCMI transport for agent interfacing the
OP-TEE SCMI service. OP-TEE provides an SCMI PTA (Pseudo-TA) for
non-secure world to send SCMI messages over an identified channel.
The driver implemented here uses a SMT shared memory for passing
messages between client and server.
The implementation opens and releases channel resources for each
passed SCMI message so that resources allocated (sessions) or
registered (shared memory areas) in OP-TEE firmware are released for
example before relocation as the driver will likely allocate/register
them back when probed after relocation.
The integration of the driver using dedicated config switch
CONFIG_SCMI_AGENT_OPTEE is designed on the model posted to the
U-Boot ML by Patrick Delaunay [1].
Link: [1] https://lore.kernel.org/all/20211028191222.v3.4.Ib2e58ee67f4d023823d8b5404332dc4d7e847277@changeid/
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove unused OPTEE_MSG_LOGIN_* ID macros as suitable TEE_LOGIN_* ID
macros are already defined tee.h.
Cc: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Change SCMI smccc transport drivers to use platform data rather
than private data for channel reference since it only stores platform
data retrieved from the DT. Consequently the probe handler is replaced
with a of_to_plat handler.
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change SCMI mailbox transport drivers to use platform data rather
than private data for channel reference since it only stores platform
data retrieved from the DT. Consequently the probe handler is replaced
with a of_to_plat handler.
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Correct scmi mailbox probe function that can't free the scmi channel
instance since its auto-allocated by the device model framework.
Cc: Simon Glass <sjg@chromium.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add two configs CONFIG_SCMI_AGENT_MAILBOX and CONFIG_SCMI_AGENT_SMCCC
to select the supported agents as all the agents are not supported.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Some boards need to change the tx/rx delay config in order for
gigabit Ethernet to work.
In Linux commit bbc4d71d6354 ("net: phy: realtek: fix rtl8211e rx/tx
delay config"), Realtek documented the bits for overriding the delays
from the hardware straps.
Copy the logic from linux, so the delay config is set from the PHY's
interface type (the phy-mode property in the device tree).
This removes the need for a one-off workaround for the Pine A64+ board.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add a driver for the MDIO interface for Aspeed AST2600 SOC. The driver
only supports clause 22 for now.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
redundant_init() is only called in the tsec driver. Make it static.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
priv->promisc is used as the parameter of the set_promisc() call
which accepts a bool type instead of char.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If using OF_CONTROL, fdtcontroladdr is set to the fdt used to configure
U-Boot. When using PXE, if no fdt is defined in the menu file, and
there is no fdt at fdt_addr, add fall back on fdtcontroladdr too.
We are developing board support for the Armv8r64 FVP using
config_distro_bootcmd. We are also using OF_BOARD and would like the
PXE boot option to default to the fdt provided by board_fdt_blob_setup.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
The list of ports which support SGMII depending on switch generation is
available here:
https://www.kernel.org/doc/html/latest/networking/dsa/sja1105.html#port-compatibility-matrix
SGMII can either be used to connect to an external PHY or to the host
port. In the first case, the use of in-band autoneg is expected, in the
last, in-band autoneg is expected to be turned off (fixed-link). So the
driver supports both cases.
SGMII support means configuring the PCS and PMA. The PCS is a Synopsys
Designware XPCS, in Linux this has a separate driver but here it is
embedded within the sja1105 driver. If needed it can be taken out later,
although we would need a UCLASS_PCS for it, which we don't have atm.
Nonetheless, I did go all the way to export an internal MDIO bus for PCS
access, because it is nice to be able to debug the PCS through commands
such as:
=> mdio read ethernet-switch@1-pcs 4 1f.0
Reading from bus ethernet-switch@1-pcs
PHY at address 4:
31.0 - 0x1140
The internal MDIO bus is not registered with DM because there is no
udevice on it, as mentioned. But the XPCS code can still be ripped out,
as needed.
I did not add support for 2500base-x because I do not expect this
interface type to be used as a boot source for anybody, it would just
add unnecessary bloat.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The SJA1105 driver is largely reused from Linux. Its programming model
is that it is blank out of reset, and it waits for a static
configuration stream over SPI, which contains all runtime parameters (it
has no notion of "default values").
Keeping a binary array for the configuration stream would have meant
that aspects such as the CPU port and the MAC speeds could have not been
configured easily, and would have been static and board-dependent.
Live-patching the binary array means recalculating the static config
table CRCs, which is not a fun process.
So we create an abstraction over the static config tables, using the
packing API, same as in Linux. The tables are kept as C structures, and
the binary configuration stream is constructed on-the-go, with CRC and
all.
All static config tables instantiated in this driver are mandatory.
The hardware reference manual can be found at:
https://www.nxp.com/docs/en/user-guide/UM10944.pdf
For tagging, a simplified version of tag_8021q from Linux is used. The
VLAN EtherType is the same (0xdadb) but since we don't want switching in
U-Boot, there is no reason to have a TX VLAN and an RX VLAN for each
port. We just need the RX VLANs to act as the unique pvid of each
front-panel port, to decode the switch port number. The RX VLAN is used
for both RX and TX.
The device tree bindings are the same as in Linux.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Instead of trying to guess which operating modes need in-band
negotiation to be active and which ones don't, parse the available
information from the device tree. That will be correct in the cases we
can already guess, and more.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Certain serial SERDES protocols like 1000base-x, 2500base-x, SGMII,
USXGMII can operate either in a mode where the PHY (be it on-board or
inside an SFP module) passes the link parameters (speed, duplex, pause)
to the MAC through in-band through control words standardized by IEEE
802.3 clause 37, or in a mode where the MAC must configure (force) its
link parameters based on information obtained out-of-band (MDIO reads,
guesswork etc).
In Linux, the OF node property named "managed" is parsed by the phylink
framework, and the convention is that if a driver uses phylink, then the
presence of this property means that in-band autoneg should be enabled,
otherwise it shouldn't.
To be compatible with the OF node bindings of drivers that use phylink
in Linux, introduce parsing support for this property in U-Boot too.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The Freescale TSEC can be a DSA master, and the ports of the attached
DSA switch can have different MAC addresses compared to the TSEC.
Nonetheless, the TSEC must receive the packets on behalf of those switch
ports. Therefore, implement the promiscuous mode method to allow DSA to
set this.
Note that the init_registers() function called from eth_ops :: start
overwrites this setting. There is no reason why the RCTRL register
should be zero-initialized, so just stop clearing it so that the setting
we applied in eth_ops :: set_promisc sticks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
The VSC8502 is a Microchip (formerly Microsemi, formerly Vitesse)
dual port, gigabit Ethernet copper PHY which supports the MII, GMII and
RGMII MAC-side interfaces.
Of these, I could only test RGMII, and my board needed RGMII delays to
be applied by software, so I am able to confirm that this patch handles
that properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
It was wrongly set to "MR", fix it.
Fixes: 52e2565bfb ("spi: atmel-quadspi: Add verbose debug facilities to monitor register accesses")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- meson64_android: handle errors on boot and run fastboot on boot failure
-----BEGIN PGP SIGNATURE-----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=i2VH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211119' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- pinctrl: Correct the driver GPIO declaration
- meson64_android: handle errors on boot and run fastboot on boot failure
This should use the provided U_BOOT_DRIVER() macro so that the driver gets
added to the appropriate linker list. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 7c9dcfed50 ("pinctrl: meson: rework gx pmx function")
Reported-by: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com> on libretech-cc
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Consulting to "NVM Express® Base Specification, revision 2.0".
If more PRP List pages are required, then the last entry of
the PRP List contains the Page Base Address of the next PRP
List page. The next PRP List page shall be memory page aligned.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Most NVME devcies maintain data in internal cache for an uncertain
times, and u-boot has no method to force NVME to flush cache.
So this patch adds FUA to avoid data loss caused by power off after data
programming.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
When booting U-Boot in crosvm, the virtual machine emulates a PCI cam
device, not the PCI-E 'ecam' device normally seen on e.g. QEMU. This
PCI device can be supported with only trivial changes to the ecam
driver.
Instead of adding a completely new driver which is identical besides the
initialization step, add support for the PCI version to the existing
driver.
Signed-off-by: Alistair Delva <adelva@google.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: Ram Muthiah <rammuthiah@google.com>
Hash and Crypto Engine (HACE) is designed to accelerate the
throughput of hash data digest, and symmetric-key encryption.
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add YCLK enable for HACE, the HW hash engine of
ASPEED AST2600 SoCs.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Chia-Wei Wang <chiawei_wang@aspeedtech.com>
With the recent changes on mmc driver, we saw that the boot is ~5 secs
longer compared to v2021.07 on mediatek platforms.
This regression is seen during mmc_init and caused by the following
patch [1].
Indeed since we did not support poll dat0, we fulfilled the condition
of [1] and a delay of 500 ms was added for every __mmc_switch call.
By adding the support of wait_dat0(), we now don't need to mdelay
during mmc_init anymore.
[1]: https://patchwork.ozlabs.org/project/uboot/patch/1629192034-64056-1-git-send-email-ye.li@nxp.com/
Signed-off-by: Julien Masson <jmasson@baylibre.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Lot of PCIe controllers are using ECAM addressing. So add common ECAM
macros into U-Boot's pci.h header file which can be suitable for most
PCI controller drivers.
Replace custom ECAM address macros in every PCI controller driver by new
ECAM macros from U-Boot's pci.h header file.
Similar macros are defined also in Linux kernel. There is a small
difference between Linux and these new U-Boot macros.
U-Boot's PCIE_ECAM_OFFSET() takes device and function numbers in separate
arguments. Linux's PCIE_ECAM_OFFSET() takes device and function numbers
encoded in one argument. The reason is that U-Boot's PCI_DEVFN() macro is
different than Linux's PCI_SLOT() macro. So having device and function
numbers in separate arguments makes code more straightforward.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This driver supports both pin muxing and GPIO support for the
pin control logic found on Apple SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
This driver uses Pinctrl framework and is compatible with the Linux
driver for AST2600.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
%d was being used as the specifier for size_t, leading to a
compiler warning
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Without get_desc, the tpm command will not provide a
description of the device in 'tpm device' or 'tpm info'.
Due to the characteristics of the Atmel TPM it isn't
possible to determine certain attributes (e.g open/close
status) without using the TPM stack (compare Infineon
and ST TPM drivers), so just print out the chip model
and udevice name as the identifier.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This driver was broken due to an empty offset byte being prepended
at the start of every transmission.
The hardware does not mimic an EEPROM device with registers so
an offset byte is not required.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There are no users of this driver without DM_I2C
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYZPDrwAKCRDKSWXLKUoM
IS9GAJ93T/uprhLcKWMb+284YMb2caWgOACfZ02nTlzvZKNNXVretJgZaHXqj1M=
=cwTL
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.01-rc3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.01-rc3
sdhci:
- Fix emmc mini case with missing firmware interface
zynqmp:
- Restore JTAG interface if required
- Allow overriding board name
- Add support for DLC21
- Fix one fallthrought statement description
- Use config macro instead of name duplication
- Save multiboot to variable
firmware:
- Handle ipi_req errors better
- Use local buffer in case user doesn't need it instead of NULL/0 location
spi:
- gqsi: Fix write issue at low frequencies
net:
- gem: Disable broadcasts
This ensures the USB_MUSB_PIO_ONLY config is set to an apppropriate
value from the changes enabling USB_MUSB_GADGET does.
Namely, USB_MUSB_PIO_ONLY default to =y on USB_MUSB_SUNXI being y.
Signed-off-by: Samuel Dionne-Riel <samuel@dionne-riel.com>
With CONFIG_SYSRESET_WATCHDOG=y the sandbox can use a watchdog based system
reset.
To make this work calling sandbox_wdt_expire_now() must lead to a reset.
With this change we can test the development suggested in
[PATCH 0/4] Improved sysreset/watchdog uclass integration
https://lists.denx.de/pipermail/u-boot/2021-August/458656.html
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The driver supports the ds1339 as well, which was probably intended by
the author but prevented by a typo. Fix the typo.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
- device-tree sync-up with Linux for ls1028a
- fixes/update in fsl-ddr driver, fsl-validate, lx2162a, fsl-mc,
spintable code, configs, qspi node, pci
- enable EFI_SET_TIME support in sl28
- powerpc: Drop -mstring
Convert our SPI TPM driver and use the newly added API
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add support for devices that expose a TPMv2 though MMIO.
Apart from those devices, we can use the driver in our QEMU setups and
test TPM related code which is difficult to achieve using the sandbox
driver (e.g test the EFI TCG2 protocol).
It's worth noting that a previous patch added TPMv2 TIS core functions,
which the current driver is consuming.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There's a lot of code duplication in U-Boot right now. All the TPM TIS
compatible drivers we have at the moment have their own copy of a TIS
implementation.
So let's create a common layer which implements the core TIS functions.
Any driver added from now own, which is compatible with the TIS spec, will
only have to provide the underlying bus communication mechanisms.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With the upcoming TPM2 API, some of the functions name are part of the new
header file. So switch conflicting internal function names and defines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canaonical.com>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
With the upcoming TPM2 API, some of the functions name are part of the new
header file. So switch conflicting internal function names and defines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
-----BEGIN PGP SIGNATURE-----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=lqEG
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20211110' of https://source.denx.de/u-boot/custodians/u-boot-stm
- DHSOM update:
- Remove nWP GPIO hog
- Increase SF bus frequency to 50Mhz and enable SFDP
- Disable video output for DHSOM
- Disable EFI
- Enable DFU_MTD support
- Create include file for STM32 gpio driver private data
- Split board and SOC STM32MP15 configuration
- Device tree alignement with v5.15-rc6 for STM32MP15
- Add binman support for STM32MP15x
- Normalise newlines for stm32prog
- Update OTP shadow registers in SPL
In some part of STM32MP15 support the CONFIG_TFABOOT can be replaced
by other config: CONFIG_ARMV7_PSCI and CONFIG_ARM_SMCCC.
This patch also simplifies the code in cpu.c, stm32mp1_ram.c and
clk_stml32mp1.c as execution of U-Boot in sysram (boot without SPL and
without TFA) is not supported: the associated initialization code is
present only in SPL.
This cleanup patch is a preliminary step to support SPL load of OP-TEE
in secure world, with SPL in secure world and U-Boot in no-secure world.
Reported-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The stm32 gpio driver private data are not needed in arch include files,
they are not used by code except for stm32 gpio and pincontrol drivers,
using the same IP; the defines for this IP is moved in a new file
"stm32_gpio_priv.h" in driver/gpio.
This patch avoids to have duplicated file gpio.h for each SOC
in MPU directory mach-stm32mp and in each MCU directory arch-stm32*
and allows to remove CONFIG_GPIO_EXTRA_HEADER for all STM32.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Header file mach/cpu.h already defines MBUS_PCI_MEM_SIZE macro which
defines size of MBUS_PCI_MEM_BASE window. So use global MBUS_PCI_MEM_SIZE
macro instead of locally defined PCIE_MEM_SIZE macro. Both macros have same
definition.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The Sunxi boards only support a 16 second watchdog timeout. This is too
short to boot Linux. The UEFI specification requires 300 seconds as
default timeout.
Change the default for CONFIG_WATCHDOG_AUTOSTART for ARCH_SUNXI.
Fixes: b147bd3607 ("sunxi: Enable watchdog timer support by default")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In the current code, it doesn't reset the cursors of LUT entry and
StreamID at the beginning of the fixup, so it can result in LUT entry
setup and msi-map mismatch and LUT entries and StreamID leaking
when reload and fixup the DTB.
This patch move the initialization of LUT entry and StreamID cursors
to the beginning of the fixup to resolve the issues.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Use moveconfig.py script to convert CONFIG_SYS_FMAN_FW_ADDR,
CONFIG_SYS_QE_FW_ADDR and CONFIG_SYS_QE_FMAN_FW_LENGTH to Kconfig and
move these entries to defconfigs.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for the proper dwc3 device tree binding support as specified
in the offical device tree spec.
Initially, add support for the LS1028A support. Other SoCs should be
easy to add by just adding the corresponding compatible string.
Unfortunately, the device trees of all other layerscape SoCs are not
converted and uses a wrong compatible string only known in u-boot.
To maintain backwards compatibility with current u-boot device trees,
add the generic "fsl,layerscape-dwc3" compatible string.
OTG mode is not supported yet. The dr_mode in the devicetree will either
have to be set to peripheral or host.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit d9612c2f0449e24983a8b689603210486a930c90]
Enable the undefined length INCR burst type and set INCRx.
Different platform may has the different burst size type.
In order to get best performance, we need to tune the burst
size to one special value, instead of the default value.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
[backport from linux commit db2be4e9e30c6e43e48c5749d3fc74cee0a6bbb3]
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both dr_mode and maximum-speed properties are usually optional. Drivers
will still try to fetch the properties nonetheless, which leads to error
messages, although they are no errors. Change pr_err() to pr_debug().
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official bindind of the PCIe controller of the ls1028a has the
following compatible string:
compatible = "fsl,ls1028a-pcie";
Additionally, the resource names and count are different. Update the
driver to support this binding and change the entry in the ls1028a
device tree.
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dwc3", "snps,dwc3";
Change the ls1028a device tree and add this new compatible to the fsl
specific xhci driver, otherwise the generic dwc3 driver will be used
with the compatibles above.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The driver will look for a named resource "ecc-addr", but this isn't the
official binding. In fact, the official device tree binding
documentation doesn't mention any resource names at all. But it is safe
to assume that it's the linux ones we have to use if we want to be
compatible with the linux device tree. Thus rename "ecc-addr" to
"sata-ecc" and convert all the users in u-boot.
While at it, also rename "sata-base" to "ahci" although its not used at
all.
This change doesn't affect the SATA controller on the ZynqMP.
Cc: Michal Simek <monstr@monstr.eu>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-lpuart";
Add the missing compatible to the driver and update the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official devicetree bindings specifies spi-num-chipselects as the
name. Use it.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The official ls1028a binding of the driver uses the following as
compatibles:
compatible = "fsl,ls1028a-dspi", "fsl,ls1021a-v1.0-dspi";
Add the missing compatible to the driver and update the device tree.
We can use the fallback "fsl,ls1021a-v1.0-dspi", because the endianness
is determined by the little-endian property and not by the compatible
string itself. Further, we won't need and specific details on the DMA
configuration (which is different on the LS1021A). If it's ever needed,
we can later add the more specific "fsl,ls1028a-dspi" compatible to the
driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
According to the linux device tree specification the compatible string
is:
compatible = "arm,sp805", "arm,primecell";
Fix all users in u-boot.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Adds check for memory clock variable before calculating caslat_actual.
Set mclk_ps to slowest DIMM supported if mclk_ps is found zero.
Signed-off-by: Maninder Singh <maninder.singh_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Bad Shift operator issue in step_to_string function
by adding an if check
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix possible divide by zero issue in fsl_ddr_set_memctl_regs
by adding an if check
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix possible divide by zero issue in get_memory_clk_period_ps
by adding a check
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
to fix following checkpatch warings.
WARNING: struct should normally be const
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dzmitry Sankouski <dsankouski@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
At present the counter never hits the comparitor in this case. Add a
special case.
This ensures that the snow backlight works when at full brightness.
Fixes: 76c2ff3e5f video: backlight: fix pwm's duty cycle calculation
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently output of dfu commands ends on a line with leading hash signs
('#'). The succeeding output should be placed on a new line.
After writing updates via dfu print a new line.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The current EFI video driver only works when running in the stub. In that
case the stub calls boot services (before jumping to U-Boot proper) and
copies the graphics info over to the efi table. This is necessary because
the stub exits boot services before jumping to U-Boot.
The app maintains access to boot services throughout its life, so does not
need to do this. Update the driver to support calling boot services
directly.
Enable video output for the app. Note that this uses the
EFI_GRAPHICS_OUTPUT_PROTOCOL protocol, even though it mentions vesa.
A sample qemu command-line for this case is:
qemu-system-x86_64 -bios /usr/share/edk2.git/ovmf-ia32/OVMF-pure-efi.fd
-drive id=disk,file=try.img,if=none,format=raw -nic none
-device ahci,id=ahci -device ide-hd,drive=disk,bus=ahci.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add an option to automatically register watchdog devices with the
wdt_reboot driver for use with sysreset. This allows sysreset to be a
drop-in replacement for platform-specific watchdog reset code, without
needing any device tree changes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently, the wdt_reboot driver always gets its watchdog device
reference from an OF node. This prevents selecting a watchdog at
runtime. Move the watchdog device reference to the plat data, so
the driver can be bound with the reference pre-provided. The
reference will still be acquired from the OF node if it is not
already provided.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
These driver probe functions are not (and should not be) called from
outside the respective driver source files. Therefore, the functions
should be marked static.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
None of the sysreset drivers do anything beyond providing sysreset
uclass ops. They should depend on the sysreset uclass.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When allocate the GPD ring, and tell its address to the controller, then
the driver starts or resumes the QMU, the controller will try to access
the first GPD, so need flush the first one to avoid wrong GPD status.
Reported-by: Xin Lin <Xin.Lin@mediatek.com>
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
According to the Armada 3720 Functional Specification Data Strobe applies
for both read and write config requests.
Data strobe bits configure which bytes from the start address should be
returned for read request. Set value 0xf (all 4 bits) into Data Strobe
register to read all four bytes from specified 32-bit config space
register. Same value for Data Strobe register is programmed by Linux
pci-aardvark.c driver for config read requests.
Without this patch pci-aardvark driver sets data strobe register only
during config write operations. So any followup config read operations
could result with just partial datai returned (if previous write operation
was not 32-bit wide). This patch fixes it and ensures that config read
operations always read all bytes from requested register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This is a pci driver, not an eth driver.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Root Complex should be the default mode, let's set it explicitly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Now that PCI Bridge is working, U-Boot's CONFIG_PCI_PNP code automatically
enables memory access and bus mastering when it is needed. So do not
prematurely enable memory access and bus mastering.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
PCI Bridge is always accessible also when link is down. So move detection
of link up from mvebu_pcie_of_to_plat() function to mvebu_pcie_valid_addr()
function which is used when accessing PCI config space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Functions mvebu_pcie_get_local_bus_nr() and mvebu_pcie_get_local_dev_nr()
are not used, so remove them.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
The mysterious "Memory controller" PCI device which is present in PCI
config space is improperly configured and crippled PCI Bridge which acts
as PCIe Root Port for endpoint PCIe card.
This PCI Bridge reports in PCI config space incorrect Class Code (Memory
Controller) and incorrect Header Type (Type 0). It looks like HW bug in
mvebu PCIe controller but apparently it can be changed via mvebu registers
to correct values.
The worst thing is that this PCI Bridge is crippled and its PCI config
registers in range 0x10-0x34 alias access to internal mvebu registers which
have different functionality as PCI Bridge registers. Moreover,
configuration of PCI primary and secondary bus numbers (registers 0x18
and 0x19) is done via totally different mvebu registers via totally strange
method and cannot be done via PCI Bridge config space.
Due to above fact about PCI config range 0x10-0x34, allocate a private
cfgcache[] buffer in the driver, to which PCI config access requests to
the 0x10-0x34 space will be redirected in mvebu_pcie_read_config() and
mvebu_pcie_write_config() functions. Function mvebu_pcie_write_config()
will also catch writes to PCI_PRIMARY_BUS (0x18) and PCI_SECONDARY_BUS
(0x19) registers and set PCI Bridge primary and secondary bus numbers via
mvebu's own method.
Also, Expansion ROM Base Address register (0x38) is available, but at
different offset 0x30. So recalculate register offset before accessing PCI
config space.
After these steps U-Boot sees working PCI Bridge and CONFIG_PCI_PNP code
can finally start enumerating all PCIe devices correctly, even with more
complicated PCI topology. So update also mvebu_pcie_valid_addr() function
to reflect state of the real device topology.
Each PCIe port is de-facto isolated and every PCI Bridge which is part of
PCIe Root Complex is also isolated, so put them on separate PCI buses as
(local) device 0.
U-Boot already supports enumerating separate PCI buses, real (HW) bus
number can be retrieved by "PCI_BUS(bdf) - dev_seq(bus)" code, so update
config read/write functions to properly handle more complicated tree
topologies (e.g. when a PCIe switch with multiple PCI buses is connected
to the PCIe port).
Local bus number and local device number on mvebu are used for determining
which config request type is used (Type 0 vs Type 1). On normal non-broken
PCIe hardware it is done by primary and secondary bus numbers. So correctly
translate settings between these numbers to ensure that correct config
requests are sent over the PCIe bus.
As bus numbers are correctly re-configured, it does not make sense to print
some initial bogus configuration during probe, so remove this debug code.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
When reading 8 or 16 bits from config space, use appropriate readb() or
readw() calls. This ensures that PCIe controller does not read more bits
from endpoint card as asked by read_config() function.
Technically there should not be an issue with reading data from config
space which are not later used as there are no clear-by-read registers.
But it is better to use correct read operation based on requested size.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Current implementation of write_config() is broken for PCI_SIZE_8 or
PCI_SIZE_16 as it always uses writel(), which means that write operation
is always 32-bit, so upper 24 bits for PCI_SIZE_8 and upper 16 bits for
PCI_SIZE_16 are cleared.
Fix this by using writeb() and writew(), respectively.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Currently driver supports only version 1 and 2.
Version 5 has slightly different registers structure
Signed-off-by: Dzmitry Sankouski <dsankouski@gmail.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
