As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
Some sections in the linker scripts are aligned to 4 bytes, which
may cause misaligned exception on some platforms, e.g.: clearing
the bss section on 64-bit hardware if __bss_start does not start
from a naturally 8 bytes aligned address.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
U-Boot SPL is not relocable. Drop these relocation sections.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
board_init_r does not return for U-Boot SPL hence there is no need
to update the link register when jumping to board_init_r.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The codes currently skip the very first relocation entry, and have
an inaccurate comment "skip first reserved entry" indicating that
the first entry is reserved, but later it references the elements
in the first relocation entry using a minus offset.
Change to use a positive offset so that there is no need to skip
the first relocation entry.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
't5' already contains relocation type so don't bother reloading it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
The __bss_start is the source end address hence load its address
directly into register 't2' for optimization.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Rick Chen <rick@andestech.com>
Since commit 409e4b5478 ("Makefile: Enforce DWARF4 output") the
whole U-Boot build switched to enforce DWARF4 output, but RISC-V
is still on its own setting. Let's switch to use U-Boot's setting.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add initial u-boot device tree for the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add initial device tree for the JH7110 RISC-V SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add board support for StarFive VisionFive v2.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add Kconfig to select the basic functions for StarFive JH7110 SoC.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
Add StarFive JH7110 SoC to support RISC-V arch.
Signed-off-by: Yanhong Wang <yanhong.wang@starfivetech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Tested-by: Conor Dooley <conor.dooley@microchip.com>
So far we used inline assembly to inject the actual instruction that
triggers the semihosting service. While this sounds elegant, as it's
really only about a few instructions, it has some serious downsides:
- We need some barriers in place to force the compiler to issue writes
to a data structure before issuing the trap instruction.
- We need to convince the compiler to actually fill the structures that
we use pointers to.
- We need a memory clobber to avoid the compiler caching the data in
those structures, when semihosting writes data back.
- We need register arguments to make sure the function ID and the
pointer land in the right registers.
This is all doable, but fragile and somewhat cumbersome. Since we now
have a separate function in an extra file anyway, we can do away with
all the magic and just write that in an actual assembler.
This is much more readable and robust.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Add the 'missing-msg' for more detailed output
on missing system firmware.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
The current ae350-related defconfigs could also
support newer Andes CPU IP, so modify the names of CPU
from ax25 to andesv5, and board name from ax25-ae350 to ae350.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To reduce the code size, CONFIG_V5L2_CACHE was disabled since commit:
ca06444aac
Turing on does not significantly increase the size of u-boot-spl.bin,
so we enable it by default to improve performance.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This patch refines L1 cache enable/disable and v5l2-cache enable
functions.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Update the compatible string of L2 cache.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As the OpenSBI v1.2 does not enable the cache [0], we enable
the i/d-cache in harts_early_init() and do not disable in
cleanup_before_linux(). This patch also simplifies the logic
and moves the CSR encoding to include/asm/arch-andes/csr.h.
[0] bd7ef41398
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
There is no need for RISCV_NDS_CACHE config to control cache switches.
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
PLIC is used for external interrupt, while PLICSW is an Andes-specific
design for software interrupt.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Add src and dst address checking, if they
are the same address, just return and don't
copy data anymore.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
When fit image boots from ram, the payload will
be prepared in the address of SPL_LOAD_FIT_ADDRESS.
In spl fit generic flow, it will malloc another
memory address and copy whole fit image to this
malloc address. But it is un-necessary for booting
from RAM.
This patch improves this flow by declare the
board_spl_fit_buffer_addr() to replace the original one.
The larger image size (eq: Kernel Image 10~20MB), it
can save more booting time.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
CCTL operations are available to Supervisor/User-mode
software under the control of the mcache_ctl.CCTL_SUEN
control bit. Enable it to support Supervisor(and User)
CCTL operations.
Signed-off-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The Priv ISA states:
"In systems without U-mode, the mcounteren register should
not exist."
Check U-Mode is present in MISA before writing to counteren, otherwise
we endup with Illegal Instruction exception on systems without U-Mode.
Also make checking MISA default for M-Mode.
Signed-off-by: Nikita Shubin <n.shubin@yadro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For the 64bit EFI binaries that we create set the
IMAGE_FILE_LARGE_ADDRESS_AWARE characteristic in the PE-COFF header
to indicate that they can handle addresses above 2 GiB.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We add RISC-V semihosting based serial console for JTAG based early
debugging.
The RISC-V semihosting specification is available at:
https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adoc
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Describe that CONFIG_SBI_V02=y does not mean SBI specification v0.2
but v0.2 or later.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
We should check the string until it hits underscore, in case it
searches multi-letter extensions. For example, "rv64imac_xandes"
will be treated as D extension support since there is a "d" in
"andes", resulting illegal instruction caused by initializing FCSR.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
The initial devicetree for PolarFire SoC incorrectly created a fixed
frequency clock in the devicetree to represent the msspll, but the
msspll is not a fixed frequency clock. The actual reference clock on a
board is either 125 or 100 MHz, 125 MHz in the case of the icicle kit.
Swap the incorrect representation of the msspll out for the actual
reference clock.
Fixes: dd4ee416a6 ("riscv: dts: Add device tree for Microchip Icicle Kit")
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Padmarao Begari <padmarao.begari@microchip.com>
Add QSPI NAND device node to the Microchip PolarFire SoC
Icicle kit device tree.
The Winbond NAND flash memory can be connected to the
Icicle Kit by using the Mikroe Flash 5 click board and
the Pi 3 Click shield.
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
In the v2022.10 Icicle reference design, the seg registers have been
changed, resulting in a required change to the memory map.
A small 4MB reservation is made at the end of 32-bit DDR to provide some
memory for the HSS to use, so that it can cache its payload between
reboots of a specific context.
Co-developed-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Padmarao Begari <padmarao.begari@microchip.com>
Reviewed-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Rick Chen <rick@andestech.com>
As PLICSW is used to trigger the software interrupt, we should rename
Andes PLIC configuration and file name to reflect the usage. This patch
also updates PLMT and PLICSW compatible strings to be consistent with
OpenSBI fdt driver.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
The IPI scheme in OpenSBI has been updated to support 8-core AE350
platform, the plicsw configuration needs to be modified accordingly.
Signed-off-by: Yu Chien Peter Lin <peterlin@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
The riscv32 toolchain for GCC-12 provided by kernel.org contains libgcc.a
compiled for double-float. To link to it we have to adjust how we build
U-Boot.
As U-Boot actually does not use floating point at all this should not
make a significant difference for the produced binaries.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The following description is copied from the equivalent patch for the
Linux Kernel proposed by Aurelien Jarno:
>From version 2.38, binutils default to ISA spec version 20191213. This
means that the csr read/write (csrr*/csrw*) instructions and fence.i
instruction has separated from the `I` extension, become two standalone
extensions: Zicsr and Zifencei. As the kernel uses those instruction,
this causes the following build failure:
arch/riscv/cpu/mtrap.S: Assembler messages:
arch/riscv/cpu/mtrap.S:65: Error: unrecognized opcode `csrr a0,scause'
arch/riscv/cpu/mtrap.S:66: Error: unrecognized opcode `csrr a1,sepc'
arch/riscv/cpu/mtrap.S:67: Error: unrecognized opcode `csrr a2,stval'
arch/riscv/cpu/mtrap.S:70: Error: unrecognized opcode `csrw sepc,a0'
Signed-off-by: Alexandre Ghiti <alexandre.ghiti@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Christian Stewart <christian@paral.in>
Reviewed-by: Rick Chen <rick@andestech.com>
