Update main_bcdma and main_pktdma nodes for native configuration in the
absence of DM services.
Reported-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Nishanth Menon <nm@ti.com>
Add support for a semihosting fallback on 32-bit ARM. The assembly is
lightly adapted from the irq return code, except there is no offset
since lr already points to the correct instruction. The C side is mostly
like ARM64, except we have fewer cases to deal with.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
U-Boot runs in supervisor mode. On ARMv6 and lower, software interrupts
are taken in supervisor mode. When entering an interrupt, the link
register is set to the address of the next instruction. However, if we
are already in supervisor mode, this clobbers the link register. The
debugger can't help us, since by the time it notices we've taken a
software interrupt, the link register is already gone. Work around this
by moving the return address to another register.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
When we take a software interrupt, we are already in supervisor mode.
get_bad_stack assumes we are not in supervisor mode so it can clobber
the stack pointer. This causes us to have an invalid stack once that
macro finishes. Revert back to the get_bad_stack_swi macro which was
previously removed.
Fixes: 41623c91b0 ("arm: move exception handling out of start.S files")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
_ Fix compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled
_ Fix issue following DT sync with kernel 6.3 for stm32mp15xx-ev1 and DHSOM SoM
_ Enable TCP, IPv6, wget on DH STM32MP15 DHSOM
_ Limit u-boot.itb size to 0x160000 bytes on DH STM32MP15 DHSOM
_ Read auth stats and boot_partition from tamp
- Fix some issues Coverity has reported, update MAINTAINERS file,
another bootstd fix, typo fix in error message, gitignore fix and
update TI's URL in many places.
Keep track of the re-entries with help of the lr register.
This binary can be re-used and called from various BROM functions.
Only when it's called from the part that handles SPI, NAND or EMMC
hardware it needs to early return to BROM ones.
In download mode when it handles data on USB OTG and UART0
this section must be skipped.
Unlike newer Rockchip SoC models the rk3066 BROM code does not have built-in
support to enter download mode on return to BROM. This binary must check
the boot mode register for the BOOT_BROM_DOWNLOAD flag and reset if it's set.
It then returns to BROM to the end of the function that reads boot blocks.
From there the BROM code goes into a download mode and waits for data
on USB OTG and UART0.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Provide configuration to read cpuid and generate a persistent
MAC address in ethaddr
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RV1126 fails to boot on 2024.01-rc1.
Commit 9e644284ab ("dm: core: Report bootph-pre-ram/sram node as
pre-reloc after relocation") changed the behaviour of bootph-pre-ram, to
limit nodes to spl phase. This caused rv1126 boards to fail to boot with
the current dts.
This patch updates the pmu/grf nodes to bootph-all tags as they are
needed in all phases. This fixes the boot issue on rv1126 boards.
Signed-off-by: Tim Lunn <tim@feathertop.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Obtain from TAMP backup register information about image authorization
status and partition id used for booting. Store this info in
environmental variables ("boot_auth" and "boot_part" correspondingly).
Image authorization supported values:
0x0 - No authentication done
0x1 - Authentication done and failed
0x2 - Authentication done and succeeded
These values are stored to TAMP backup register by Trusted Firmware-A [1].
Testing:
STM32MP> print boot_part
boot_part=1
STM32MP> print boot_auth
boot_auth=2
[1] https://git.trustedfirmware.org/TF-A/trusted-firmware-a.git/commit/?h=refs/heads/integration&id=ab2b325c1ab895e626d4e11a9f26b9e7c968f8d8
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Co-developed-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The patch fixed by this commit renders ST STM32MP15xx EV1 board and
all DHSOM SoM based boards unbootable from SPI NOR. Fix the damage
by updating -u-boot.dtsi to match the stm32mp15-pinctrl.dtsi update.
Fixes: 08002ffd08 ("ARM: dts: stm32mp: alignment with v6.3")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
While 23e20b2fa6 ("arm: stm32mp: Fix compilation issue when
SYS_DCACHE_OFF and/or SYS_DCACHE_SYS are enabled") tried fixing
this issue, fix it really by adding #if checks for SYS_ICACHE_OFF
and SYS_DCACHE_OFF.
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
QuartzPro64 is a Rockchip RK3588 based SBC by Pine64.
UART and boot over SD/eMMC/RJ45 are tested to work.
Linux commits from next-20231013:
8152d3d070a9 ("arm64: dts: rockchip: Add QuartzPro64 SBC device tree")
Signed-off-by: Tom Fitzhenry <tom@tom-fitzhenry.me.uk>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Cc: Eugen Hristev <eugen.hristev@collabora.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Ondrej Jirman <megi@xff.cz>
The migration deadline for moving to DM_SCSI was v2023.04. A further
reminder was sent out in August 2023 to the remaining platforms that had
not migrated already, and that a few more over the line (or configs
deleted).
With this commit we:
- Rename CONFIG_DM_SCSI to CONFIG_SCSI.
- Remove all of the non-DM SCSI code. This includes removing other
legacy symbols and code and removes some legacy non-DM AHCI code.
- Some platforms that had previously been DM_SCSI=y && SCSI=n are now
fully migrated to DM_SCSI as a few corner cases in the code assumed
DM_SCSI=y meant SCSI=y.
Signed-off-by: Tom Rini <trini@konsulko.com>
In order to not rely on common.h providing a number of common includes,
cleanup what we include directly in order to be able to drop common.h
later.
Signed-off-by: Tom Rini <trini@konsulko.com>
The include <asm/arch/cpu.h> references values in <asm/arch/omap3.h> and
so include it directly here rather than rely on indirect inclusion.
Signed-off-by: Tom Rini <trini@konsulko.com>
In matching other architectures that have their global_data.h need to
bring in a types.h header, switch to <linux/types.h> on PowerPC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a mostly empty asm/barrier.h file for sandbox where we define nop() to
be an empty function.
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add some dependencies on features that we had been selecting so that we
can still disable CMDLINE.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This is not used for sandbox, so drop it. Enable the things that it
controls to avoid dstrastic changes in the config settings for
sandbox builds.
The end result is that these are enabled:
BOOTMETH_DISTRO
BOOTSTD_DEFAULTS
and these are disabled:
USE_BOOTCOMMAND
BOOTCOMMAND (was "run distro_bootcmd")
DISTRO_DEFAULTS
Note that the tools-only build has already disabled DISTRO_DEFAULTS
and BOOTSTD_FULL
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Xilinx is using standard mtd partition layout for quite a long time. It is
used for testing purpose on evaluation boards.
Also #address/size-cells shouldn't be present without nodes which should
use them that's why move them from zynq-7000.dtsi to nand/nor nodes
directly.
The patch was tested on zc706 and zedboard(with also increasing max
frequency and rx bus width).
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4c3348981bba32d3892194420d78fe8621c47534.1698837725.git.michal.simek@amd.com
SMMU is disabled by default and not all masters can be enabled at the same
time because of limited number of entries. That's why comment all iommu
properties but keep them for reference in DT. In XEN case they should be
added back and Xen should have SMMU enabled by default.
Also add IDs for DP and DPDMA.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e868c27c52ded5d8ef25f75ba394b1ab3b31b80a.1698825657.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a99a8d72201a782fc811715942dea97fb5ab583b.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which ospi/qspi can
be that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/9518ab1c4299a45e800b8611172edd78c9243132.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/e7d31a9d9c4a76e171eefc619f31fabd0831a614.1698329087.git.michal.simek@amd.com
Mini U-Boot is running out of OCM and it's only purpose is to program non
volatile memories. There are different configurations which qspi can be
that's why describe them via DT.
DT binding is already approved that's why there is no reason not to add it.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/28b3cdd7e91b2b4c3c36d0bf65aa5bac042f248c.1698329087.git.michal.simek@amd.com
gpio38 is used in SOM's kv260 to reset the Ethernet PHY.
At present, HW reset is not working properly as Tri-state
is enabled for MIO38, causing inappropriate PHY register reads.
Disabled Tri-state for MIO38 to make HW reset work.
Tri-state disable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7a3 00000540
Tri-state enable :
ZynqMP> md 0xFF180208 2
ff180208: 00bfe7e3 00000540
Signed-off-by: Tejas Bhumkar <tejas.arvind.bhumkar@amd.com>
Link: https://lore.kernel.org/r/20231020050622.972750-1-tejas.arvind.bhumkar@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The baudrate configured in .config is taken by default by serial. If
change of baudrate is required then the .config needs to changed and
u-boot recompilation is required or the u-boot environment needs to be
updated.
To avoid this, support is added to fetch the baudrate directly from the
device tree file and update.
The serial, prints the log with the configured baudrate in the dtb.
The commit c4df0f6f31 ("arm: mvebu: Espressobin: Set default value for
$fdtfile env variable") is taken as reference for changing the default
environment variable.
The default environment stores the default baudrate value, When default
baudrate and dtb baudrate are not same glitches are seen on the serial.
So, the environment also needs to be updated with the dtb baudrate to
avoid the glitches on the serial.
Also add test to cover this new function.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230921112043.3144726-3-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This adds support for the Inteno XG6846 board based on the
Broadcom MIPS 6328 SoC.
The default boot will read a uImage from flash and boot it.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Board specific late init allows vendors to set up different device
or board specific env variables (like serial number, platform name).
In case this information is missing, u-boot will lack info regards
serial or platform.
To avoid this prior nvidia_board_late_init internal generic function
is called which fills required data. In this case platform name is
obtained from get_chip and serialno is filled with SoC id.
Though SoC id is not dedicated to be devices serial but it fits well
in case of restriction of data about device and since SoC is basically
a main chip of the device.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Transformers
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # Nvidia Tegratab
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Re-crypt support was extended to devices without burnt SBK. In case
SBK is not set, place from where it is read is filled with zeroes.
This patch adds support for ebtupdate function to detect nosbk device
and avoid crypto operations for it.
Tested-by: Maksim Kurnosenko <asusx2@mail.ru>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
