Move all rk3128 u-boot specific properties in separate dtsi files.
Sort emmc node.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3128
sync the clock dt-binding header.
This is the state as of v6.0 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip platform use TPL to do the DRAM initialize for all the SoCs,
if TPL is not available, means no available DRAM init program, and the
u-boot-rockchip.bin is not functionable.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Change-Id: I2299f1eddce5aa7d5fb1a3fb4d8aeaa995b397fa
The legacy Allwinner code is cluttered with #ifdef's, some of them even
nested, which makes the code hard to read and error prone.
Eventually we will get rid of most of them, but for now let's at least
annotate the #endif lines with the corresponding symbol the bracket
started with.
Reviewed-by: Samuel Holland <samuel@sholland.org>
Tested-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The functions board_fit_image_post_process() and board_tee_image_process()
are not actually board specific (despite their names). Any board using the
OMAP2 family can use these functions. Move them to boot-common.c.
Signed-off-by: Andrew Davis <afd@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add OSPI Support such that this device can boot up using OSPI Flash.
Also can use the flash for other purposes if required from uboot.
Signed-off-by: Dhruva Gole <d-gole@ti.com>
Introduce the auto-generated clock tree and power domain data needed to
attach the am62a into the power-domain and clock frameworks of uboot
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce the base dts files needed for u-boot or to augment the
linux dtbs for use in the u-boot-spl and u-boot binaries
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Introduce the basic am62a7 SoC dtbs from the v6.1-rc3 tag of the linux
kernel along with the new am62a specific pinmux definition that we will
use to generate the dtbs for the u-boot-spl and u-boot binaries
Co-developed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Enable the EBI and NAND flash controller. Define the pinctrl and
partition table
Signed-off-by: Balamanikandan Gunasundar <balamanikandan.gunasundar@microchip.com>
- Kautuk's semihosting patch:
move semihosting library from arm directory to common place and add
RISC-V support
- Zong's Kconfig patch:
use "imply" instead of "select" to allow user to decide if
SPL_SEPARATE_BSS should be selected
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmORqHQcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyF4qCACQZLl0WPPGOABtlJdB
7a5bZUwjeQdwES78Mx7N4pYAldafv+yBbzDHg/8fp3zS70xuMgqHmmDHgQ7GinvX
lOpFaWpxDTOkEOCn6+2x90mNpCh0siuCptUyaHfQ+B5L3leXqb3DTJuBLQyMbjAE
bhGjImPfZY+KdPY3VTkIK0fIZJD+/woysTSA5RCC8JmIUEHgPnOxes47gRCyKoug
sznMzYO5gGP7jpA9p1QXOLLiiAENQ+DxiCUdQDrDHm0PxTk8YQbhEiF0Svm476FL
hLuuuccCOzY1obCm9z70dDOhvmkH7tKHs02Es00nGEk2X+ZrI0oG0FtH4Z7CcZKF
WcWV
=PJWw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-fixes-2023.01-b' of https://source.denx.de/u-boot/custodians/u-boot-at91
Second set of u-boot-at91 fixes for the 2023.01 cycle:
This is a single tiny fix that allows the correct name for one pin on
sama7g5 device. People with DT coming from Linux will have build errors
without this if they add NAND device.
We factor out the arch-independent parts of the ARM semihosting
implementation as a common library so that it can be shared
with RISC-V.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
As DM_ETH is required for all network drivers, it's now safe to remove
the non-DM_ETH support code. Doing this removes some board support code
which was also unused. Finally, this removes some CONFIG symbols that
otherwise needed to be migrated to Kconfig, but were unused in code now.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only need to enable DM_ETH if we have a networking driver. All
networking drivers depend on DM_ETH being enabled, and their selection
ensures DM_ETH will be enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The pl18x MMCI driver does not use the interrupt-names property,
the binding document has been updated to recommend this property
be unused, remove it.
Backport of Marek's Linux patch:
https://lore.kernel.org/linux-arm-kernel/20221013221242.218808-3-marex@denx.de/
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
On STM32MP135F-DK, the SD card detect GPIO is GPIOH4.
Backport of the Linux patch:
https://lore.kernel.org/linux-arm-kernel/20220921160334.3227138-1-yann.gautier@foss.st.com/
Signed-off-by: Yann Gautier <yann.gautier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Adds support of Clock and Reset drivers for STM32MP13 platform.
Signed-off-by: Gabriel Fernandez <gabriel.fernandez@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is a bad idea, and more modern toolchains will fail, if you declare
an assembly function to be global and then weak, instead of declaring it
weak to start with. Update assorted assembly files to use the WEAK macro
directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Pali Rohár <pali@kernel.org>
This option controls using board/samsung/common/misc.c, so add a Kconfig
file there as well and select it from the boards which use this
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_NOBQFMAN
CONFIG_SYS_DPAA_DCE
CONFIG_SYS_DPAA_FMAN
CONFIG_SYS_DPAA_PME
CONFIG_SYS_DPAA_RMAN
CONFIG_SYS_PMAN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_PCI and
CONFIG_SYS_PCIE namespace do not easily transition to Kconfig. In many
cases they likely should come from the device tree instead. Move these
out of CONFIG namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_OMAP_ABE_SYSCK
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NUM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NS16550
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SPL_NS16550_MIN_FUNCTIONS
CONFIG_SYS_NS16550_MEM32
CONFIG_SYS_NS16550_PORT_MAPPED
CONFIG_SYS_NS16550_REG_SIZE
CONFIG_SYS_NS16550_SERIAL
To do this we also introduce CONFIG_SPL_SYS_NS16550_SERIAL so that
platforms can enable the legacy driver here for SPL.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_NAND
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
ZynqMP mini configurations are not using IPI driver and enabling this is
adding additional ~1200 Bytes (depends on configuration).
This ends up in situation that there is no enough space in OCM for
relocation that's why disable this driver for all mini configurations.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c71bab3927cb71ae517d9c21f59f3d5cf0caf712.1669734580.git.michal.simek@amd.com
The commit ed35de6170 ("Convert CONFIG_ZYNQMP_PSU_INIT_ENABLED to
Kconfig") converted CONFIG_ZYNQMP_PSU_INIT_ENABLED symbol and enabled it by
default which is not correct configuration.
Intention of this config was to have it enabled by default for SPL and
provide an option to users to also do low level initialization directly
from U-Boot.
That's why it is necessary to define second symbol with SPL marking in it
and properly use symbols depends on usage in Makefile.
Also disable ZYNQMP_PSU_INIT_ENABLED from boards which enables it by
default. CONFIG_SPL_ZYNQMP_PSU_INIT_ENABLED is enabled by default when SPL
is enabled.
Reported-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/d5fcbd66b05bf0d7ef594e66464ee23b48c5e4cc.1669969083.git.michal.simek@amd.com
When Linux boot takes over control of the pmu
(by signaling PM_INIT_FINALIZE via ipi), pmu will switch off 'unused'
rpu cores. The Xilinx zynqmp fsbl prevents switching off those cores by
marking rpu cores as 'used' when loading code partitions to those cores.
The current u-boot SPL is missing this behaviour, which results in
halting rpu cores during Linux boot.
This commit mimics the xilinx zynqmp fsbl behavior by marking r5 cores as
used when they are released during boot.
Signed-off-by: Lukas Funke <lukas.funke@weidmueller.com>
Signed-off-by: Lukas Funke <lukas.funke-oss@weidmueller.com>
Link: https://lore.kernel.org/r/20221028121547.26464-2-lukas.funke-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The SanCloud BBE requires the same dtb nodes to be present in the SPL as
the AM335x EVM.
The SanCloud BBE Lite also requires the SPI flash node and all
dependencies to be present in the SPL to support SPI boot.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
For successful boot when CONFIG_SPL_OF_CONTROL=y, we need to ensure that
the board EEPROM on i2c0, the uart0 serial port and the relevant boot
device (mmc1 or mmc2) can be accessed in the SPL. We also need to
preserve the parent nodes for each required dtb node.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The signal name of pin PD8 with function D is A22_NANDCLE
as it is defined in the datasheet.
Fixes: 558378a4cd ("ARM: mach-at91: add support for new SoC sama7g5")
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
Use macro to represent the RL and WL setting to ensure the PHY and
controller setting are aligned.
Review-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
- Re-add the old PHY reset binding for nanopi-k2
-----BEGIN PGP SIGNATURE-----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=yEaP
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20221122' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Implement setbrg op to meson serial device
- Re-add the old PHY reset binding for nanopi-k2
The sync of device-tree/bindings in 11a48a5a18c6 ("Linux 5.6-rc2") causes
Ethernet to break on some GXBB boards; the PHY seems to need proper reset
timing to function in u-boot and Linux. Re-add the old PHY reset binding
for dwmac until we support new bindings in the PHY node. This borrows the
same fix applied to the Odroid C2 board [0].
[0] https://lists.denx.de/pipermail/u-boot/2021-April/446658.html
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Link: https://lore.kernel.org/r/20221025143205.14470-1-christianshewitt@gmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support octal spi flash and uses DCC terminal
for console output. Add required dts for octal spi flash mini u-boot
configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add configuration file for mini u-boot configuration which runs on a
smaller footprint from on chip memory(OCM). This configuration has
required CONFIG's enabled to support qspi flash and uses DCC terminal
for console output. Add required dts files for qspi mini configuration.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20221116141155.14788-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add soc_xilinx_versal_net driver to identify the family & revision of
versal-net SoC. Add Kconfig option CONFIG_SOC_XILINX_VERSAL_NET to
enable/disable this driver. To enable this driver by default, add this
config to xilinx_versal_net_virt_defconfig file. This driver will be
probed using platdata U_BOOT_DEVICE structure which is specified in
mach-versal-net/cpu.c.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/613d6bcffd9070f62cf348079ed16c120f8fc56f.1668612993.git.michal.simek@amd.com
The fclk-enable property is set to 0 which disables all FCLKs.
Enable all FCLKs so they can be used as clock sources in the
programmable logic.
Signed-off-by: Christian Kohn <christian.kohn@xilinx.com>
Acked-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/b1308dc1f14f8eb24662019f7376c959e5e763b8.1665567031.git.michal.simek@amd.com
Removing the zynq_board_read_rom_ethaddr() function as
xlnx,eeprom is not used anymore. As all board dts to use
nvmem alias instead of xlnx,eeprom.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20221017094818.17996-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Apply commit 534f0fbd65 ("arm64: Fix relocation of env_addr if
POSITION_INDEPENDENT=y") also for 32-bit ARM.
This change fixes crashing of U-Boot on ARMv7 (Omap3 / Cortex-A8) Nokia N900
phone (real HW). Note that qemu emulator of this board with same u-boot.bin
binary has not triggered this crash.
Crash happened after U-Boot printed following debug lines to serial console:
initcall: 0001ea8c (relocated to 8fe0aa8c)
Loading Environment from <NULL>... Using default environment
Destroy Hash Table: 8fe25a98 table = 00000000
Create Hash Table: N=387
Signed-off-by: Pali Rohár <pali@kernel.org>
We should guard the SPL nodes against CONFIG_SPL_BUILD to fix
the following build error when the blobs are absent:
binman: Fail open first container file mx8qm-ahab-container.img
Signed-off-by: Fabio Estevam <festevam@denx.de>
These files reference SZ_ macros without including <linux/sizes.h>,
correct this.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Originally, the mmc aliases node was present in imx6qdl-wandboard.dtsi.
After the sync with Linux in commit d0399a46e7 ("imx6dl/imx6qdl:
synchronise device trees with linux"), the aliases node is gone as
the upstream version does not have it.
This causes a regression in which the SD card cannot be found anymore:
Since commit the aliases node has been removed
U-Boot 2022.10-00999-gcca41ed3d63f-dirty (Nov 03 2022 - 22:07:38 -0300)
CPU: Freescale i.MX6QP rev1.0 at 792 MHz
Reset cause: POR
DRAM: 2 GiB
Core: 62 devices, 17 uclasses, devicetree: separate
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by passing the alias node in the u-boot.dtsi file to
restore the original behaviour where the SD card (esdhc3) was
mapped to mmc0.
Fixes: d0399a46e7 ("imx6dl/imx6qdl: synchronise device trees with linux")
Signed-off-by: Fabio Estevam <festevam@denx.de>
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-By: Tim Harvey <tharvey@gateworks.com> #imx8m{m,n,p}-venice-*
Synchronise device tree with linux v6.1-rc3.
Note: Nowadays, the intent is for them regular device trees to just be
synchronised from them Linux kernel device trees and any and all U-Boot
specific changes need to go into the -u-boot.dtsi device tree include
files which BTW get included automatically by the U-Boot build system.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate to using automatic build system included -u-boot.dtsi device
tree include files.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Tested-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
In order to boot over USB, the device tree needs to enable
a few extra nodes in SPL. Since the USB driver has the
ability to detect host/device, the dr_mode can be removed
from the device tree since it needs to act as a device when
booting and OTG is the default mode. Add USB boot support
to spl_board_boot_device and enable the corresponding config
options.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The e10133 workaround was broken in two places:
- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
While the old register values were saved, the actual masking was
missing.
- imx_udelay() expects the system counter to run at its base frequency,
but the system counter is switched to a lower frequency earlier in
psci_system_suspend(), leading to a much longer delay than intended.
Replace the call with an equivalent loop (linux-imx 5.15 does the same)
This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.
Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This enables armv8 crypto extension usage for SHA1/SHA256.
Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The RD-AC5X-32G16HVG6HLG-A0 development board main components and
features include:
* Main 12V/54V power supply
* 270 Gbps throughput packet processor on the main board
* DDR4:
* SR1: 2GB DDR4 2400MT/S(1GB x 2 pcs ) with ECC(1GB x 1 pcs)
* SR2: 4GB DDR4 2400MT/S(2GB x 2 pcs ) with ECC(2GB x 1 pcs)
* PCB co-layout with 4GB device to support 8GB (Dual CS) requirement
* 16GB eMMC (Samsung KLMAG1JETD-B041006)
* 16MB SPI NOR(GD25Q127C)
* 32 x 1000 Base-T interfaces
* 16 x 2500 Base-T interfaces
* SR1: 88E2540*4
* SR2: 88E2580*1+88E2540*2
* Six (6) x 25G Base-R SFP28 interfaces
* One (1) x RJ-45 console connector, interfacing to the on board UART
* One (1) x USB Type-A connector, interfacing to the USB 2.0 port (0)
* One (1) x USB Type-mini B connector, interfacing to the USB 2.0 port (1)
* One (1) x RJ-45 1G Base-T Management port, interfacing to the host
port (shared with PCIe) Connected to 88E1512 Gigabit Ethernet Phy
* One (1) x Oculink port, interfacing to the PCIe port for external CPU
connection
* POE 802.3AT support on Port 1 ~ Port 32, 802.3BT support on Port 33 ~
Port 48 (Microsemi PD69208T4, PD69208M or TI TPS2388,TPS23881
solution)
* POE total power budget 780W
* LED interfaces per network port/POE
* LED interfaces (common) showing system status
* PTP TC mode Supported (Reserved M.2 connector to support BC mode)
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Add support for the Allecat5/Alleycat5X SoC. These are L3 switches with
an integrated CPU (referred to as the CnM block in Marvell's
documentation). These have dual ARMv8.2 CPUs (Cortex-A55). This support
has been ported from Marvell's SDK which is based on a much older
version of U-Boot.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
The 64-bit mvebu SoCs don't have a suitable timer driver so add a !ARM64
condition to the select.
Fixes: 7b530bb19e ("arm: mvebu: Use CONFIG_TIMER on all MVEBU & KIRKWOOD platforms")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The uart1 node was missing the 'clock-frequency' property. This meant
the driver for this device would fail at probe.
The clock for uart1 is fed from the same source as uart0 and is a fixed
200MHz clock. This is confirmed via documentation for the CN9130 SoC
and from the equivalent code in Linux at:
<linux>/arch/arm64/boot/dts/marvell/armada-ap80x.dtsi
where uart0 and uart1 share a common 'clocks' definition.
Signed-off-by: Hamish Martin <hamish.martin@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add the needed bus mappings for the two main RTI memory ranges and
the required device tree nodes in the main domain.
Same as kernel commit 6dd8457dc20693e2ba9054c171499b22664fd4e7
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
So far the Calxeda machines were using the CONFIG_SYS_TIMER_* macros to
simply hardcode the address of the counter register of the SP804 timer.
This method is deprecated and scheduled for removal.
Use the newly introduced SP804 DM_TIMER driver to provide timer
functionality on Highbank and Midway machines. The base address and base
frequency are taken from the devicetree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently our semihosting trap function is somewhat fragile: we rely
on the current compiler behaviour to assign the second inline assembly
argument to the next free register (r1/x1), which happens to be the
"addr" argument to the smh_trap() function (per the calling convention).
I guess this is also the reason for the noinline attribute.
Make it explicit what we want: the "addr" argument needs to go into r1,
so we add another register variable. This allows to drop the "noinline"
attribute, so now the compiler beautifully inlines just the trap
instruction directly into the calling function.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Commit f4b540e25c5c("arm: smh: Fix uninitialized parameters with newer
GCCs") added a memory clobber to the semihosting inline assembly trap
calls, to avoid too eager GCC optimisation: when passing a pointer, newer
compilers couldn't be bothered to actually fill in the structure that it
pointed to, as this data would seemingly never be used (at least from the
compiler's point of view).
But instead of the memory clobber we need to tell the compiler that we are
passing an *array* instead of some generic pointer, this forces the
compiler to actually populate the data structure.
This involves some rather hideous cast, which is best hidden in a macro.
But regardless of that, we actually need the memory clobber, but for two
different reasons: explain them in comments.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The ARM semihosting interface uses different trap instructions for
different architectures and instruction sets. So far we were using
AArch64 and ARMv7-M, and had an untested v7-A entry. The latter does
not work when building for Thumb, as can be verified by using
qemu_arm_defconfig, then enabling SEMIHOSTING and SYS_THUMB_BUILD:
==========
{standard input}:35: Error: invalid swi expression
{standard input}:35: Error: value of 1193046 too large for field of 2 bytes at 0
==========
Fix this by providing the recommended instruction[1] for Thumb, and
using the ARM instruction only when not building for Thumb. This also
removes some comment, as QEMU for ARM allows to now test this case.
Also use the opportunity to clean up the inline assembly, and just define
the actual trap instruction inside #ifdef's, to improve readability.
[1] https://developer.arm.com/documentation/dui0471/g/Semihosting/The-semihosting-interface?lang=en
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FWU Multi Bank Update feature allows the platform to boot the
firmware images from one of the partitions(banks). The first stage
bootloader(fsbl) passes the value of the boot index, i.e. the bank
from which the firmware images were booted from to U-Boot. On the
STM32MP157C-DK2 board, this value is passed through one of the SoC's
backup register. Add a function to read the boot index value from the
backup register.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The FWU metadata structure is accessed through the driver model
interface. On the stm32mp157c dk2 and ev1 boards, the FWU metadata is
stored on the uSD card. Add the fwu-mdata node on the u-boot specifc
dtsi file for accessing the metadata structure.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
As STI timer is renamed to ARM A9 global timer, change BCM63138 to use
the new global timer config symbol name.
This patch applies on top of the my previous patch [1].
[1]: https://lists.denx.de/pipermail/u-boot/2022-August/491060.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6753 is essentially same as the main chip BCM6855 but with different
SKU number. Now that BCM6855 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6855, remove the original ARCH_BCM6753 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm96753ref board folder. It is replaced by the
generic bcmbca board folder.
- Merge the 6753.dtsi setting to the new 6855.dtsi file. Update
96753ref board dts with the new compatible string.
- Delete broadcom_bcm96763ref.h and merge its setting to the new
bcm96855.h file.
- Delete bcm96753ref_ram_defconfig and use a basic config version of
bcm96855_defconfig
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6855 is a Broadcom ARM A7 based PON Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
broadband SoC, this patch adds it under CONFIG_BCM6855 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL101 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM6858 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM6858, remove the original ARCH_BCM6858 support and migrate its
configuration and dts settings. This includes:
- Remove the bcm968580xref board folder. It is replaced by the generic
bcmbca board folder.
- Update bcm968580xref board dts with the new compatible string.
- Delete broadcom_bcm968580xref.h and merge its setting to the new
bcm96858.h file.
- Remove bcm968580xref_ram_defconfig as a basic config version of
bcm96858_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6858 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other broadband
SoC, this patch adds it under CONFIG_BCM6858 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and the
original dts is updated with the one from linux next git repository.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM68360 is a variant within the BCM6856 chip family. Now that BCM6856
is supported under CONFIG_ARCH_BCMBCA and CONFIG_BCM6856, remove the
original ARCH_BCM68360 support and migrate its configuration and dts
settings. This includes:
- Remove the bcm968360bg board folder. It is replaced by the generic
bcmbca board folder.
- Merge the 68360.dtsi setting to the new 6856.dtsi file. Update board
dts with the new compatible string.
- Merge broadcom_bcm968360bg.h setting to the new bcm96856.h file.
- Remove bcm968360bg_ram_defconfig as a basic config version of
bcm96856_defconfig is now added.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM6856 is a Broadcom B53 based PON Gateway SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family. Like other Broadband
SoC, this patch adds it under CONFIG_BCM6856 chip config and
CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and Broadcom uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
Now that BCM63158 is supported under CONFIG_ARCH_BCMBCA and
CONFIG_BCM63158, remove the original ARCH_BCM63158 support and migrate
configuration settings.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63158 is a Broadcom B53 based DSL Gateway SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family. Like other
Broadband SoC, this patch adds it under CONFIG_BCM63158 chip
config and CONFIG_ARCH_BCMBCA platform config.
This initial support includes a bare-bone implementation and dts with
CPU subsystem, memory and ARM PL011 uart. This SoC is supported in the
linux-next git repository so the dts and dtsi files are copied from
linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM4908 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added
under ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux git repository so the dts and dtsi
files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM6813 is a Broadcom B53 based PON and WLAN AP router SoC. It is part
of the BCA (Broadband Carrier Access origin) chipset family so it's
added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM4912 is a Broadcom B53 based WLAN AP router SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts
and dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63146 is a Broadcom B53 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
BCM63138 is an ARM A9 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory, ARM A9 global timer
and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are stripped down version of linux copies with mininum blocks
needed by u-boot.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there to the console.
This patch applies on top of the my previous patch [1].
[1] https://lists.denx.de/pipermail/u-boot/2022-August/490570.html
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
BCM63148 is an Broadcom B15 based DSL Broadband SoC. It is part of the
BCA (Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6756 is an ARM A7 based WLAN Gateway and Access Point Broadband SoC.
It is part of the BCA(Broadband Carrier Access origin) chipset family so
it's added under ARCH_BCMBCA platform. This initial support includes a
bare-bone implementation and dts with CPU subsystem, memory and ARM
PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6878 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011
uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM6846 is an ARM A7 based PON Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and Broadcom uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry point
address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
BCM63178 is an ARM A7 based DSL Broadband SoC. It is part of the BCA
(Broadband Carrier Access origin) chipset family so it's added under
ARCH_BCMBCA platform. This initial support includes a bare-bone
implementation and dts with CPU subsystem, memory and ARM PL011 uart.
This SoC is supported in the linux-next git repository so the dts and
dtsi files are copied from linux with minor fix-up that needs to be
upstreamed to linux as well.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
This is actually a panel, not a video device. Rename the option, move it
into the right place and make it depend on PANEL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Layerscape update
- support sysreset,
- de-select FSL_IFC when booting from SD
- disable unused parts of ICID tables
- reduce ns_dev size for csu
- enable dma snooping for ls104x
- nand driver fixups for ls1043ardb rev 7.0 boards.
Avoid the following build errors after the device tree sync:
drivers/spi/mxs_spi.c: In function ‘mxs_spi_probe’:
drivers/spi/mxs_spi.c:327:25: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘spi_max_frequency’
327 | priv->max_freq = dtplat->spi_max_frequency;
| ^~
drivers/spi/mxs_spi.c:328:23: error: ‘struct dtd_fsl_imx23_spi’ has no
member named ‘num_cs’
328 | plat->num_cs = dtplat->num_cs;
| ^~
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
