Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Simon Glass <sjg@chromium.org>
The __get_unaligned_le* functions may not be declared on all platforms.
Instead, get_unaligned_le* should be used. On many platforms both of
these are the same function.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In asix_recv() the call to convert the endianess of the receive header
was applied on the wrong variable. Instead of converting rx_hdr it
converted pkt_hdr which is a pointer, and not yet initialiazed at this
point.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Added support for the Cypress GX3 SuperSpeed to Gigabit Ethernet
Bridge Controller (VID_04b4/PID_3610).
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Moves code from ehci_hcd_init to new function ehci_fsl_init
which can be re-used in CONFIG_DM_USB.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
The meaning of CONFIG_USB in U-Boot is different from that in Linux.
As you see in drivers/usb/Kconfig of Linux, CONFIG_USB enables the
USB host controller support, while CONFIG_USB_SUPPORT is used to
enable the whole of the USB sub-system.
When I added CONFIG_USB into Kconfig by commit 6e7e9294d3 ("usb:
add basic USB configs in Kconfig"), I planned to follow the Linux's
convention, i.e. CONFIG_USB to enable/disable the USB host support.
Then, commit 68f7c5db2d ("usb: Generic USB Kconfig option, that
fits both host and gadget and comments") changed the logic of the
CONFIG_USB to point to the whole of the USB sub-system. As a result,
currently we do not have an option for USB host.
This commit adds CONFIG_USB_HOST, which will be useful to compile
in the USB host support code.
CONFIG_USB_HOST is not referenced at all, but strangely some boards
define it in board headers. I removed them because USB_HOST will be
selected in Kconfig going forward.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
There is no UHCI driver entry in Kconfig for now, but we have some
UHCI drivers, for example, LEON. This is a placeholder in case we
want to move them to Kconfig in the future.
The help message was copied from Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add this option as a common config for all OHCI controllers. Its
help message was copied from Linux. Also, I moved it below EHCI
to respect the order in Linux's Kconfig.
Add CONFIG_USB_OHCI_HCD=y to axs103_defconfig, which is the only
user of OHCI_GENERIC.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for driver model, so that CONFIG_DM_ETH can be defined and
used with this driver.
This patch also adds the read_rom_hwaddr() callback so that the ROM MAC
address will be used to the DM part of this driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Ted Chen <tedchen@realtek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Support driver model for ehci mx6 driver.
Consolidate code to be shared between DM and non-DM, such as
introducing ehci_mx6_common_init.
For simplicity, some old fasion code are keeped for DM usage,
such as board_ehci_power and board_usb_phy_mode. And 'dr-mode',
usbphy and vbus handling code for DM is not added now.
These will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: Simon Glass <sjg@chromium.org>
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Invalidate dcache before starting the DMA to ensure coherency. In case
there are any dirty lines from the DMA buffer in the cache, subsequent
cache-line replacements may corrupt the buffer in memory while the DMA
is still going on. Cache-line replacement can happen if the CPU tries to
bring some other memory locations into the cache while the DMA is going
on.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The total FIFO size of some SoCs may be different from the existen, this
patch supports fifo size setting from platform data.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far, Rockchip SoCs have two kinds of USB2.0 phy, such as Synopsys and
Innosilicon. This patch applys dwc2 usb driver framework to implement
phy_init() and phy_off() methods for Synopsys phy on Rockchip platform.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add Kconfig entry config option for USB_EHCI_ZYNQ
and update the same to enable for all zynq boards
which supports USB
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add a new config CONFIG_MXC_USB_OTG_HACTIVE which configures the
OTG Power Pin to be high active. Low active is the reset value
of the affected configuration register, hence the config option
is named by the non-reset configuration.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
USBNC_n_CTRL1 bit 9 actually controls the power pin polarity.
Rename UCTRL_PM to align reference manual and set the bit in
the appropriate callback usb_power_config.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Freescale ARMv8 SoC name ends with "A" to represent ARM SoCs.
like LS2080A, LS1043A, LS1012A.
So append "A" to SoC names.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- update fastboot_okay() and fastboot_fail()
This file originally came from upstream code.
While retaining the storage abstraction feature, this is the second
set of the changes required to resync with the
cmd_flash_mmc_sparse_img()
in the file
aboot.c
from
https://us.codeaurora.org/cgit/quic/la/kernel/lk/plain/app/aboot/aboot.c?h=LE.BR.1.2.1
Signed-off-by: Steve Rae <srae@broadcom.com>
This "session-id" alogrithm is not required, and currently corrupts
the stored image whenever more the one "session" is required.
Signed-off-by: Steve Rae <srae@broadcom.com>
The USBNC_PHYCFG2_ACAENB bit should be cleared to enable the
OTG ID detection, not set it. When the bit is set, the ACA
Resistance Detection is enabled, which disables the OTG ID
detection, because the internal pull up is off.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is a 4 bytes hole between phy_cfg2 and phy_status, fix the
usbnc_regs structure to include the hole.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
If the usb controller is not running, no need to shutdown it,
otherwise `usb stop` complains about:
"EHCI failed to shut down host controller".
To i.MX7D SDB, there are two usb ports, one Host, one OTG.
If we only plug one udisk to the Host port and then `usb start`,
the OTG controller for OTG port does not run actually. Then,
if `usb stop`, the OTG controller for OTG port will also be
shutdown, but it is not running.
This patch adds a check to only shutdown the running controller.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: "Stefan Brüns" <stefan.bruens@rwth-aachen.de>
Cc: Stephen Warren <swarren@nvidia.com>
This patch is doing the following:
1. Implementing the errata for LS2080.
2. Adding fixup for fdt for LS2080.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
This patch does the following things:
1. Makes the errata checking code common for PPC and ARM
2. Moves all these static inline functions into a dedicated C file
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Performs code cleanup for device tree fixup for fsl usb controllers by
making functions to handle these similar errata checking code.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Define CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8 to allow the
physical interface to be 8-bit (rather than 16-bit).
Signed-off-by: Steve Rae <srae@broadcom.com>
Turn of the clock and assert the reset when musb_stop gets called, so that
the os gets the musb controller in a pristine state. This fixes a spurious
VBus error interrupt triggering as soon as the Linux musb driver loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Create an entry for "config USB_XHCI_DWC3" in Kconfig and
switch over to it for all boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Move CONFIG_USB_XHCI to defconfig files for all boards, renaming it
into CONFIG_USB_XHCI_HCD.
As commented in the help of "config USB_XHCI" entry, this has been
a TODO for a long time; now CONFIG_USB_XHCI_HCD and CONFIG_USB_XHCI
have been unified in favor of the former.
Note:
Some boards define CONFIG_USB_XHCI in their headers without
CONFIG_USB, which does not meet the "depends on" in Kconfig.
I added CONFIG_USB=y for those boards when converting.
Otherwise, they would fail to build.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The index returned by get_sys_clk_index() is not exactly what we expect.
Let's not rely on that and use get_sys_clk_freq() instead.
This fixes missing USB3 devices in the Linux kernel when USB is started
in u-boot. It still doesn't fix missing USB3 devices in u-boot though.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reported by Coverity:
Logically dead code (DEADCODE)
dead_error_line: Execution cannot reach this statement:
(f_dfu->strings + --i).s = ....
If calloc failed, i is still 0 and no need to call free,
so discard the dead code.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
With patch c998da0d (usb: Change power-on / scanning timeout handling),
the USB scanning is started earlier and with a smaller timeout. This
resulted on SoCFPGA (using the DWC2 driver) in some USB sticks not
getting detected any more. This patch now adds a 1 second delay (in
the host mode only) to the DWC2 driver before the scanning is started.
With this delay, now all problematic USB keys are detected successfully
again. And there is no need any more to change the delay / timeout
in the common USB code (usb_hub.c).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
There could be runtime determined board specific reason why a EHCI
initialization fails (e.g. ENODEV if a Port is not available). In
this case, properly return the error code.
While at it, that function (board_ehci_hcd_init) has actually two
documentation blocks... Use the correct function name for the
documentation block of board_usb_phy_mode.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Initialize desc_before_addr, otherwise the USB core won't send the
first 64B Get Device Descriptor request in common/usb.c function
usb_setup_descriptor() . There are some USB devices which expect
this sequence and otherwise can misbehave.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Tom Rini <trini@konsulko.com>
Introduce a new flag in the controller private data, which allows selectively
disabling the OC protection. Use the standard 'disable-over-current' OF prop
to set this flag. This OC protection must be disabled on EBV SoCrates rev 1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Introduce a boolean flag in the dwc2 controller private data and set
it according to the macro (for now) instead of having this macro
directly in the dwc_otg_core_init(). This will let us configure the
flag from DT or such later on, if needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Pass the whole bulk of private data instead of just the regs,
since the private data will soon contain important configuration
flags.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Remaining bytes means bytes that are not yet transferred
and not the bytes that were transferred in the last transfer.
Reported-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm28155_ap board]
Request size can be greater than ep.packet and still end in a
short packet. We need to tackle this case as end of transfer
(if short_not_ok is not set) as indicated in USB 2.0 Specification [1],
else we get stuck up on certain protocols like fastboot.
[1] - USB2.0 Specification, Section 5.3.2 Pipes
Reported-by: Steve Rae <steve.rae@broadcom.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <steve.rae@broadcom.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Just use ep->maxpacket to get the maxpacket size
and simplify the bulk-out maxpacket alignment.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
In a dual speed configuration we need to check at runtime if
we want to enable the Full-Speed or High-Speed endpoint.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Steve Rae <srae@broadcom.com>
[Test HW: bcm235xx board]
wMaxPacketSize for IN endpoing in High-Speed must be 512 and not 64.
While fixing that we do some clean ups like
- use cpu_to_le16(decimal_length) instead of hexadecimal length.
- No need to initialize bInterval to 0. Static variables are 0 initialized.
- Move descriptor setting from fastboot_add to to fastboot_bind.
- check for dual speed configuration before setting the high speed descriptors.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Steve Rae <srae@broadcom.com>
Tested-by: Steve Rae <srae@broadcom.com> [Test HW: bcm235xx board]
While at it, remove obsolete CONFIG_USBDOWNLOAD_GADGET option from some
config headers. This is also probably fixes am335x_baltos board.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Move CONFIG_USB_GADGET_DUALSPEED option to Kconfig and
make all UDC controllers select USB_GADGET_DUALSPEED:
- add next options to Kconfig selecting USB_GADGET_DUALSPEED:
- USB_GADGET_ATMEL_USBA
- USB_GADGET_DWC2_OTG
- USB_DWC3
- CI_UDC
- make USB_MUSB_GADGET select USB_GADGET_DUALSPEED
While at it, make some related fixes:
- remove DUALSPEED from configs that don't enable gadget support:
- kwb.h
- tseries.h
- add missing USB_GADGET option to next configs:
- novena_defconfig
- pcm051_rev*_defconfig
- xfi3_defconfig
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The description was borrowed from kernel. Definitions were added to
defconfig files in a way that "make savedefconfig" generates exactly
the same file as used defconfig.
Boards using 0 mA as CONFIG_USB_GADGET_VBUS_DRAW value were moved to use
2 mA (as minimal allowed by Kconfig).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
The USB Mass Storage (ums) works in Windows, Linux and OS X (EL Capitan).
But, not in OS X (Yosemite). By applying the said patch, it extends
the ums support.
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid XU3 (./test/py UMS + DFU tests)
Tested-by: John Tobias <john.tobias.ph@gmail.com>
Linux:
- Run ums to expose all my eMMC partition - shows all correctly
- Run ums to expose only 1 partition of my eMMC - show correctly
Windows:
- Run ums to expose all my eMMC partition - it detects but it prompts,
if I want to format it (due to a non windows partition)
- Run ums to expose only the FAT32 partition - it show the partition
correctly.
On the H3 we need to enable the clk and de-assert the reset of the
companion to be able to talk to the actual usb host controller.
Before this commit we were also disabling the companion clk-gate /
asserting its reset on remove, causing the later remove callback of
the companion itself to (sometimes) fail with:
ERROR: USB HC reset timed out!
This commit fixes this by not disabling the companion's clk-gate nor
asserting its reset on remove.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
musb_lowlevelinit(): if no device is plugged in / detected call
musb_stop() to undo the preceding musb_start() call.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The probe function of the musb host driver can be called multiple
times. The code assumes that it can save the pointer to the allocated
musb struct in the driver model priv_auto_alloc data, but this data
gets free-ed on a probe failure or on removal, so we must save the
pointer elsewhere.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Changes the return type of fdt_usb_get_node_type from char* to int
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Move usb device-tree fixup framework from ehci-fsl.c to common place so
that it can be used by other drivers as well (xhci-fsl.c).
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit fixes crash on BananaPi (and possibly others)
casued by 3f9f8a5b83.
Crash reason:
When no ops were passed to ehci_register(), USB host driver caused
NULL pointer dereference.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
This driver adds support of PIC32 MUSB OTG controller as dual role device.
It implements platform specific glue to reuse musb core.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
Definition of writes{bwlq}, reads{bwlq} are now added into arch specific
asm/io.h. So removing them from driver to fix re-definition error
Signed-off-by: Purna Chandra Mandal <purna.mandal@microchip.com>
This driver is able to reconfigure OTG controller into HOST mode.
Board can add board-specific initialization as board_prepare_usb().
It requires USB_ULPI_VIEWPORT enabled in board configuration.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Use definitions from ehci.h instead.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Debug printf used '%u' to print size_t variable.
This caused warnings on 64-bit machines.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
Code generates compilation warnings on 64-bit machines where pointer
is cast to u32.
This patch drops all but last 8 bits of register address.
It is possible, because addresses on ULPI bus are 6- or 8-bit.
It is not possible (according to ULPI 1.1 spec) to have more
than 8-bit addressing.
This patch should not cause regressions as all calls to
ulpi_read/write use either structure pointer (@ address 0) or integer
offsets cast to pointer - addresses requested are way below 8-bit range.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
The following options can be now enabled via defconfig:
- CONFIG_USB_ULPI
- CONFIG_USB_ULPI_VIEWPORT
- CONFIG_USB_ULPI_VIEWPORT_OMAP
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Some host controllers need addidional initialization after ehci_reset()
In non-dm implementation it is possible to use CONFIG_EHCI_HCD_INIT_AFTER_RESET.
This patch adds similar option to ehci drivers using dm.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
smsc95xx_read_reg() should calculate sizeof(*data) not sizeof(data) since
data is a pointer, and the value pointed at is being transferred over USB,
not the value of the pointer. This fixes operation of the driver in 64-bit
builds, such as the Raspberry Pi 3.
Reported-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some boards need to expose device specific variable through fastboot
(to adpat the flashing script depending on hardware revision for
example).
Provide a way to expose custom fastboot variables. Note that all
variables meant to be exposed through fastboot should be be prefixed
with 'fastboot.', the variable should not exceed 32 bytes (including
the prefix and the trailing '\0') and the variable content should
fit in the response buffer (60 bytes excluding the 'OKAY' prefix and
the trailing '\0').
Signed-off-by: Rob Herring <rob.herring@linaro.org>
[Boris Brezillon: add a commit message]
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Steve Rae <srae@broadcom.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We have a separate compatible for almost each SoC. Add one for the A83T.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Like the Allwinner A33 SoC, the A83T is missing the config register
from the musb USB DRD hardware block. Use a known working value for
it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The description was borrowed from kernel. "tristate" type was changed
to "bool" (I believe we don't support modules for u-boot yet, right?).
CONFIG_USB_GADGET requires CONFIG_USB to be defined too, so add it along
as well.
Definitions were added to defconfig files in a way that
"make savedefconfig" generates exactly the same file as used defconfig.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Add zynq_zc702 conversion]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 2nd usb controller on sun4i/sun7i has its base address 0x8000
bytes from the 1st one, rather then 0x1000. Also the ahb clk gates
are interleaved with the ohci clk-gates introducing a hole between
the clks for usb1 and usb2.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add test into xhci_submit_control_message for usb requesttype in USB
vendor request being of standardized type. This fixes detection of
certain USB fixes, for example Ethernet, USB 3.0 port. Non standardized
requesttype in USB vendor request will be ignored.
Signed-off-by: Ted Chen <tedchen@realtek.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
When 'usb start' is used, block devices are created for any USB flash sticks
and disks, etc. When 'usb stop' is used, these block devices are currently
not removed.
We don't want old block devices hanging around since they can still be
visible to U-Boot. Therefore, when USB is shut down, remove and unbind all
the block devices created by the USB subsystem.
Possibly we should unbind all devices which don't cause problems by being
unbound. Most likely we can remove everything except USB controllers, hubs
and emulators. We can consider that later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
This adds support for the OMAP4 MUSB USB controller, with a matching Linux
compat definition, TWL6030 USB device setup and USBOTGHS register setup.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary overcurrent
error which would then disable the host port.
The overcurrent condition was happening on the SoCFPGA Cyclone5 devkit, thus
USB was not working on the devkit. This patch fixes that problem.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
In case when usb_composite_register() failed once (for whatever reason),
it will fail further even if all conditions are correct. Example:
=> fastboot 2
Invalid Controller Index
couldn't find an available UDC
g_dnl_register: failed!, error: -19
exit not allowed from main input shell.
=> fastboot 0
g_dnl_register: failed!, error: -22
exit not allowed from main input shell.
Despite that 0 is correct index for USB controller, "fastboot 0" command
will fail, because "composite" structure wasn't cleared properly on
previous fail (on "fastboot 2" command).
This patch fixes that erroneous behavior, allowing us to use composite
even after previous failure.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Fix the following warning on aarch64 introduced by using p2v/v2p
functions in the code:
In file included from ./arch/arm/include/asm/byteorder.h:29:0,
from include/compiler.h:125,
from include/image.h:19,
from include/common.h:88,
from drivers/usb/host/ehci-hcd.c:10:
drivers/usb/host/ehci-hcd.c: In function ‘ehci_td_buffer’:
drivers/usb/host/ehci-hcd.c:250:49: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
^
include/linux/byteorder/little_endian.h:34:51: note: in definition of macro ‘__cpu_to_le32’
#define __cpu_to_le32(x) ((__force __le32)(__u32)(x))
^
drivers/usb/host/ehci-hcd.c:250:24: note: in expansion of macro ‘cpu_to_hc32’
td->qt_buffer[idx] = cpu_to_hc32(virt_to_phys((void *)addr));
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Tom Rini <trini@konsulko.com>
Fix the formatting in error messages, and demote one error message
to a warning, as it is only informational.
Signed-off-by: Steve Rae <srae@broadcom.com>
The alignment and size were swapped, leading to malloc heap corruption.
On my system, this sometimes caused U-Boot to crash during or after
certain USB Ethernet operations.
Fixes: c8c2797c38 ("dm: usb: eth: Support driver model with USB Ethernet")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch fixes situation when one would like to write large file into
medium with the file system (fat, ext4, etc).
This change sets file size limitation to the DFU internal buffer size.
Since u-boot is not supporting interrupts and seek on file systems, it
becomes challenging to store large file appropriately.
To reproduce this error - create large file (around 26 MiB) and sent it
to the target board.
Lets examine the flow of USB transactions:
0. DFU uses EP0 with 64B MPS [Max Packet Size]
1. Send file - OUT (PC->target) - dat_26MiB.img is sent with 4096 B transactions
2. Get status - OUT (PC->target) - wait for DFU_STATE_dfuDNLOAD_IDLE (0x05) sent
from target board - IN transaction
(target->PC)
3. The whole file content is sent to target - OUT (PC->target) with ZLP [Zero
Length Packet]
Now the interesting part starts:
4. OUT (PC->target) Setup transaction (request to share DFU state)
5. IN (target->PC) - reply the current DFU state
- In the UDC driver the req->completion (with dfu_flush) is called
after successful IN transfer.
- The dfu_flush() (called from req->completion callback) saves the
whole file at once (u-boot doesn't support seek on fs).
Such operation takes considerable time. When the file
is large - e.g. 26MiB - this time may be more than 5 seconds.
6. OUT (PC->target) - ZLP, is send in the same time when dfu_flush()
writes data to eMMC memory.
The dfu-util application has hard coded timeout on USB transaction
completion set to 5 seconds (it uses libusb calls).
When the file to store is large (e.g. 26 MiB) the time needed to write it
may excess the dfu-util timeout and following error message will be displayed:
"unable to read DFU status" on the HOST PC console.
This change is supposed to leverage DFU's part responsible for storing files
on file systems. Other DFU operations - i.e. raw/partition write to NAND and
eMMC should work as before.
The only functional change is the error reporting. When dfu_flush() fails
the u-boot prompt will exit with error information and dfu-util application
exits afterwards as well.
Test HW:
- Odroid XU3 (Exynos5433) - test with large file
- Trats (Exynos4210) - test for regression - eMMC, raw,
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reported-by: Alex Gdalevich <agdalevich@axion-biosystems.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Heiko Schocher <hs@denx.de>
Add explicit cpu_to_be32()/be32_to_cpu() conversion to BE EHCI I/O
accessors to align them with their LE counterpart. No functional
change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
If the USB EHCI is configured for little endian MMIO, make sure to
clear the USBMODE_BE flag from the USBMODE register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Certain processor architectures, like MIPS, require that the USB
structures and transfer buffers are passed with their PA to the
USB controller. If VA is passed, the USB will not work. Add the
necessary virt_to_phys() calls into the USB EHCI code to make it
work.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Some architectures, like MIPS, require remapping of the registers.
Add the map_physmem() call to handle it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Add support for phy 1-3.
Signed-off-by: Jelle van der Waa <jelle@vdwaa.nl>
[hdegoede@redhat.com: use setclrbits_le32 instead of read-modify-write]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Due to introducing the new PLLB clock handle functions,
use these functions to clean up the PLLB enable/disable code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Tested-by: Heiko Schocher <hs@denx.de>
Due to introducing the new UTMI PLL clock handle functions,
use these function to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Due to introducing the new peripheral clock handle functions,
use these functions to reduce the duplicated code.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Heiko Schocher <hs@denx.de>
[fixup for missing clk.h in at91_emac.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Now, all this driver does can be covered by the generic EHCI driver
(drivers/usb/host/ehci-generic.c). UniPhier SoCs have switched to
use it. Delete this driver rather than bothering to convert it to
Driver Model.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Marek Vasut <marex@denx.de>
Correct spelling of "U-Boot" shall be used in all written text
(documentation, comments in source files etc.).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
In current high speed fastboot, fs_ep_in.wMaxPacketSize is configured 64 bytes
as default, as a result, it failed to match the size at initialization stage in
usb controller.
Actually, hardware can support less than or equal to 512 bytes in high speed mode,
so I changed the condition from '!=' to '>' to fix this issue.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Tested-by: Steve Rae <srae@broadcom.com>
This driver is designed in a generic manner, so clocks should be
handled genericly as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
BUILD_BUG_* macros have been defined in several headers. It would
be nice to collect them in include/linux/bug.h like Linux.
This commit is cherry-picking useful macros from include/linux/bug.h
of Linux 4.4.
I did not import BUILD_BUG_ON_MSG() because it would not work if it
is used with include/common.h in U-Boot. I'd like to postpone it
until the root cause (the "error()" macro in include/common.h causes
the name conflict with "__attribute__((error()))") is fixed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use existing library function to poll bit(s).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Add a compatible string to allow this to be specified in the device tree
if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds driver support for the Realtek RTL8152B/RTL8153 USB
network adapters.
Signed-off-by: Ted Chen <tedchen at realtek.com>
[swarren, fixed a few compiler warnings]
[swarren, with permission, converted license header to SPDX]
[swarren, removed printf() spew during probe()]
Signed-off-by: Stephen Warren <swarren at nvidia.com>
USB protocol allows for 16 IN and 16 OUT endpoints (USB 2.0 Spec,
8.3.2.2 Endpoint Field). A function may have an EP 1 for both IN and OUT,
so these two should be kept separate. As EPs are either BULK or INTERRUPT
(or ISO), it is fine to have one array per direction for all transfer
types (also see e236519b73).
USB device address is 7 bits, so a bus may have more than 16 devices.
Check the device number, as the DWC2 driver only supports BULK/ISO for
the first 16 devices.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
CSPLITs for INTERRUPT transactions have to be scheduled in each microframe
following the SSPLIT. INTERRUPT transfers are executed in the next even/
odd microframe depending on the HCCHAR_ODDFRM flag.
As there are no handshakes for INTERRUPT SSPLITs the SSPLIT may have
failed (transport error) without the error being detected by the host
driver. If the last CSPLIT is not received within 4 microframes after the
SSPLIT there was a transaction error and the complete transaction has
to be restarted.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
In contrast to non-SPLIT transfers each transaction has to be submitted
as an individual chunk.
The transaction state machine proceeds from SSPLIT to CSPLIT if the ACK
flag is set. CSPLIT has to be repeated while NYET is set.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
The split register setting is used for both SSPLIT and CSPLIT transactions,
the bit for CSPLIT has to be set seperately.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Split the movement of data between CPU and Host Controller from the
status handling and tracking of transfer progress.
This will also simplify adding of SPLIT transaction support.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
A transfer is completed if the XFERCOMP flag is set, irrespective of the
ACK flag. BULK OUT transfers to some HS devices complete without having
the ACK flag set, which signal the devices has responded with an NYET
to the transfer (PING protocol).
The new behaviour matches the Linux kernel minus any PING protocol.
Also see 5966defabdcc (usb: dwc2: fix bulk transfers)
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Fix two errors in transfer len calculation, move loop invariant code out
of loop.
If xfer_len is equal to CONFIG_DWC2_MAX_TRANSFER_SIZE (or slightly
smaller), the xfer_len will be to large, e.g.:
xfer_len = MAX_TRANSFER_SIZE = 65535
max packet size = 512
=> num_packets = 128
=> IN xfer_len = 65536
For OUT transactions larger than (65536 - mps) bytes, the xfer_len
determination is quite awkward, it is only correct due to:
- max_packet_size for control/bulk/interrupt is required to be
power-of-two.
- (CONFIG_DWC2_MAX_TRANSFER_SIZE + 1) % max-packet-size is zero
for all allowed (2^3 ... 2^9) packet sizes
As the max xfer len is loop invariant, it can be moved out of the loop.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add board_usb_phy_mode weak function on similar lines to ehci-mx6.
However since Vybrid USB does not have a true OTG, make this weak
functon just return 0. The function is supposed to be implemented
by the individual boards using a GPIO for providing the OTG pin
functionality.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
The current ehci-vf USB driver for Vybrid hardcodes the USB host
and client functionality. Remove this.
Reported-by: Santhosh Kumar Janardhanam <santhosh.kj@hcl.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
All the i.MX6, i.MX23 and i.MX28 OTG controllers only support UTMI
interface. Set to ULPI is not correct, even the controller will
reject this setting in PORTSC register.
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With format-security errors turned on, GCC picks up the use of sprintf with
a format parameter not being a string literal.
Simple uses of sprintf are also converted to use strcpy.
Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Extend the ums command to accept a list of block devices. Each of these
will be exported as a separate LUN. An example use-case would be:
ums 0 mmc 0,0.1,0.2
... which would export LUNs for eMMC 0's user data, boot0, and boot1 HW
partitions. This is useful since it allows the host access to everything
on the eMMC without having to somehow stop the ums command from executing
and restart it with different parameters.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adjust this driver to support driver model for Ethernet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Remove stamp data and create common functions for the main Ethernet
operations. This will make it easier to convert this driver to support
driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Convert this driver to use the new driver model PCI API.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Most driver model PCI functions have a dm_ prefix. At some point, when the
old code is converted to driver model and the old functions are removed, we
will drop that prefix.
For consistency, we should use the dm_ prefix for all driver model
functions. Update pci_get_bdf() accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The ifdef'ed Linux kernel code uses the 1 based port number, whereas U-Boot
puts a 0 based port number into the register. The reason the 0 based port
number apparently works can probably be taken from the USB 2.0 spec:
8.4.2.2 Start-Split Transaction Token
... The host must correctly set the port field for single and multiple TT
hub implementations. A single TT hub implementation *may ignore* the port
field.
Actually, as far as I understand, a multi TT hub defaults to single TT
(bAlternateSetting: 0) until switched via SetInterface, so even "port 42"
would work.
The change was verified by hardcoding the port number to a wrong value,
SPLIT transactions kept working (although using a DWC2 instead of MUSB).
Tested hubs are the RPi onboard SMC9514 and an external "05e3:0608
Genesys Logic, Inc. USB-2.0 4-Port HUB". The former is a multi TT hub,
the latter single TT only.
Addendum: Tested on sunxi/MUSB by Hans de Goede
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Start split and complete split tokens need the hub address and the
downstream port of the first HS hub (device view).
The core of the function was duplicated in both host/ehci_hcd and
musb-new/usb-compat.h.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
flush_dcache_range may access data after priv->aligned_buffer end if
len > DWC2_DATA_BUF_SIZE.
memcpy may access data after buffer end if done > 0
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
This driver is meant to be used with any OHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
With the old order of initialization the hcor pointer has been setup to
the same address as Exynos EHCI base address (0x12110000 instead of
0x12110010).
Such behaviour was caused by reading value of 0 instead of 0x10 from EHCI
HCCPBASE register without doing proper clock initialization before.
To fix this problem hcor initialization has been moved after USB PHY setup.
Now ehci_readl(&ctx->hcd->cr_capbase) returns correct value.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
The driver is actually for the Designware DWC2 controller.
This patch renames the global s3c_udc.h header to dwc2_udc.h.
The rename is done automatically:
$ sed -i "s/s3c_udc\.h/dwc2_udc.h/g" \
`git grep "s3c_udc\.h" | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the second and final to rename global symbol,
the s3c_udc_probe() function.
The rename is done automatically:
$ sed -i "s/s3c_udc_probe/dwc2_udc_probe/g" \
`git grep s3c_udc_probe | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the first to rename global symbol, the struct
s3c_plat_otg_data.
The rename is done automatically:
$ sed -i "s/s3c_plat_otg_data/dwc2_plat_otg_data/g" \
`git grep s3c_plat_otg_data | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The s3c-otg IP block is in fact a DWC2 OTG one, so finally rename the
config option to make it less misleading. No functional change, just
a mechanical change done using the following script:
git grep USB_GADGET_S3C_UDC_OTG | cut -d : -f 1 | sort -u | \
while read line ; do
sed -i "s/USB_GADGET_S3C_UDC_OTG/USB_GADGET_DWC2_OTG/g" $line ;
done
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
Tweak the comments in the driver to reflect this fact.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the remaining S3C_* macros to match the
DWC2 naming.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the local source files to dwc2_*c and
adjusts the Makefile to use the new names.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the local header files to dwc2_*h and
adjusts the sources to use the new names.
Signed-off-by: Marek Vasut <marex@denx.de>
The extern statements are useless, remove them. Also remove the
extern ... controller, which is completely useless.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the remaining local s3c_*() functions
to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep_*() functions to reflect this.
The function s3c_udc_probe() is a special case and is not
renamed by this patch yet.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep_*() functions to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames the s3c_ep0_*() functions to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_request to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_ep to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_dev_*_ep to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_phy to struct dwc2_usbotg_phy
to make things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
Most of the functions are local to the s3c_udc driver, remove them
from the s3c_udc.h header to stop those bits from propagating all
over the place. Instead, move all the private stuff into new private
s3c_udc_otg_priv.h header.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_reg to struct dwc2_usbotg_reg
to make things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_udc to struct dwc2_udc to make
things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch removes unsued function usb_phy_reset, rather common function
dwc3_phy_reset is used.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
As per dwc3 databook, delay is required before taking the core out of reset.
This delay is required so that the PHY are stable, and then we can take core
out of reset.
Reference is taken from linux dwc3 code, file: drivers/usb/dwc3/core.c.
Signed-off-by: Sriram Dash <sriram.dash@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
The DM entry should be unique, otherwise it will collide with other
drivers. Fix this by assigning the driver a more unique name than
usb_ehci.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Simon Glass <sjg@chromium.org>
The driver does "return 0" in function with void type.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
fix the following build warnings:
drivers/usb/dwc3/core.c: In function ‘dwc3_uboot_init’:
drivers/usb/dwc3/core.c:625:6: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
^
drivers/usb/dwc3/dwc3-omap.c: In function ‘dwc3_omap_uboot_init’:
drivers/usb/dwc3/dwc3-omap.c:380:7: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
omap = devm_kzalloc(dev, sizeof(*omap), GFP_KERNEL);
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following build break:
drivers/usb/host/xhci-omap.c:35:5: error: ‘board_usb_init’ aliased to external symbol ‘__board_usb_init’
int board_usb_init(int index, enum usb_init_type init)
^
Signed-off-by: Felipe Balbi <balbi@ti.com>
This is necessary to distinguish between the "dfu-util --detach" and
the "dfu-util --reset" requests.
The default weak implementation of dfu_usb_get_reset() unconditionally
reboots the device, but we want to be able to continue the boot.scr
execution after writing the kernel, fdt and ramdisk to RAM via DFU.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add a simple USB keyboard driver for sandbox. It provides a function to
'load' it with input data, which it will then stream through to the normal
U-Boot input subsystem. When the input data is exhausted, the keyboard stops
providing data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Each scan of the USB bus may return different results. Existing driver-model
devices are reused when found, but if a device no longer exists it will stay
around, de-activated, but bound.
Detect these devices and remove them after the scan completes.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function should not be used with driver model. While there are users
of USB Ethernet that use driver model for USB but not Ethernet, we have
to keep it around. Add a comment to that effect.
Signed-off-by: Simon Glass <sjg@chromium.org>
Each USB device has an emulator. Currently this can only be found by
supplying the 'pipe' value, which contains the device number. Add a way
to find it directly from the emulated device.
Signed-off-by: Simon Glass <sjg@chromium.org>
We would like the serial number to come from the device tree node name of
the emulated device. This avoids them all having the same name. Adjust the
code to support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix below compilation warings happening for hikey_defconfig
drivers/usb/eth/smsc95xx.c:698:56: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
debug("** %s(), len %d, buf %#x\n", __func__, length, (int)msg);
^
include/common.h:109:26: note: in definition of macro ‘debug_cond’
printf(pr_fmt(fmt), ##args); \
^
drivers/usb/eth/smsc95xx.c:698:2: note: in expansion of macro ‘debug’
debug("** %s(), len %d, buf %#x\n", __func__, length, (int)msg);
^
drivers/usb/eth/smsc95xx.c:718:2: warning: format ‘%u’ expects argument of
type ‘unsigned int’, but argument 2 has type ‘long unsigned int’ [-Wformat=]
debug("Tx: len = %u, actual = %u, err = %d\n",
^
drivers/usb/eth/smsc95xx.c: In function ‘smsc95xx_recv’:
drivers/usb/eth/smsc95xx.c:802:19: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
cur_buf_align = (int)buf_ptr - (int)recv_buf;
^
drivers/usb/eth/smsc95xx.c:802:34: warning: cast from pointer to integer
of different size [-Wpointer-to-int-cast]
cur_buf_align = (int)buf_ptr - (int)recv_buf;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
So far the fastboot code was only supporting MMC-backed devices for its
flashing operations (flash and erase).
Add a storage backend for NAND-backed devices.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The fastboot flash command that writes an image to a partition works in
several steps:
1 - Retrieve the maximum size the device can download through the
"max-download-size" variable
2 - Retrieve the partition type through the "partition-type:%s" variable,
that indicates whether or not the partition needs to be erased (even
though the fastboot client has minimal support for that)
3a - If the image is smaller than what the device can handle, send the image
and flash it.
3b - If the image is larger than what the device can handle, create a
sparse image, and split it in several chunks that would fit. Send the
chunk, flash it, repeat until we have no more data to send.
However, in the 3b case, the subsequent transfers have no particular
identifiers, the protocol just assumes that you would resume the writes
where you left it.
While doing so works well, it also means that flashing two subsequent
images on the same partition (for example because the user made a mistake)
would not work withouth flashing another partition or rebooting the board,
which is not really intuitive.
Since we have always the same pattern, we can however maintain a counter
that will be reset every time the client will retrieve max-download-size,
and incremented after each buffer will be flashed, that will allow us to
tell whether we should simply resume the flashing where we were, or start
back at the beginning of the partition.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The functions and a few define to generate a fastboot message to be sent
back to the host were so far duplicated among the users.
Move them all to a common place.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Cast u32 bit value to 64bit before recasting to 64bit pointer to avoid
pointer from integer cast size mismatch warnings.
Warning log:
+../drivers/usb/gadget/udc/udc-core.c: In function
‘usb_gadget_unmap_request’:
+../drivers/usb/gadget/udc/udc-core.c:68:19: warning: cast to pointer
from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch removes this warning:
CC drivers/usb/gadget/f_thor.o
drivers/usb/gadget/f_thor.c: In function ‘thor_tx_data’:
drivers/usb/gadget/f_thor.c:572:2: warning: format ‘%d’ expects argument
of type ‘int’, but argument 4 has type ‘long unsigned int’ [-Wformat=]
debug("%s: dev->in_req->length:%d to_cpy:%d\n", __func__,
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to cache-flush the hcca area after the initial memset, otherwise
on the first hc_interrupt we might see an old $random value as done_head and
try to interpret that as the address for a completed td (followed by chaos).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Using NAKs on empty RX fifo for bulk in transfers is the right choice
for a interrupt driven model, but U-Boot uses polling and expects an
immediate answer if there is no incoming packet. Using ZLP Bulk In Response
(BIR) mode avoids unexpected timeouts in the host controller driver.
As ZLP mode is reset default, there is no need to set it.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
smsc95xx_recv() does not reassemble bursts spread over multiple URBs.
If there is a lot of broadcast traffic, the fifo will fill up to the
burst cap limit. Lowering the burst cap to the URB size ensures no packet
spans multiple urbs.
Caveat, lower limit for working burst cap is 5/33 HS/FS packets.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add missing definitions for the ubi/ubifs sync
with linux 4.2, also change "#define kfree ..."
into a static inline, so prevent ubi compile error:
CC drivers/mtd/ubi/fastmap.o
drivers/mtd/ubi/fastmap.c: In function 'scan_pool':
drivers/mtd/ubi/fastmap.c:475:3: error: called object 'free' is not a function
Signed-off-by: Heiko Schocher <hs@denx.de>
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds driver model (DM) support to the Marvell EHCI driver.
This will be used by the MVEBU SoC's, currently Armada XP and 38x.
Tested on Marvell Armada XP and 38x eval boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The current fastboot support assumes that CONFIG_FASTBOOT_FLASH implies
that we have an MMC in our system, which might not be the case if we have
some other storage device.
Change the configuration option protecting that call to
FASTBOOT_FLASH_MMC_DEV, that makes much more sense.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This arch does not seem to be supported / used at all in the current
U-Boot mainline source tree any more. So lets remove the core u8500 code
and code that was only referenced by this platform.
Please note that this patch also removes these config options:
- CONFIG_PL011_SERIAL_RLCR
- CONFIG_PL011_SERIAL_FLUSH_ON_INIT
As they only seem to be referenced by u8500 based boards. Without any
such board in the current code, these config option don't make sense
any more. Lets remove them as well.
If someone still wants to use this platform, then please send patches
to re-enable support by adding at least one board that references this
code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Commit 6a13241635 "ci_udc: Update the ci_udc driver to support bulk
transfers" caused the value of "len" to change without updating subsquent
users of that variable in ci_ep_submit_next_request(). This caused the
code that detects when to emit ZLPs (Zero Length Packets) never to
trigger, which in turn caused host timeouts when a ZLP was required,
which in turn broke tests/dfu/, even despite the assertion in that
commit's description that "These changes are tested for both the DFU and
lthor."
Fix this by modifying the added dtd iteration code not to modify "len",
but rather to keep state in a separate variable. Rename the variables
while we're at it so they describe their purpose better.
Fixes: 6a13241635 ("ci_udc: Update the ci_udc driver to support bulk transfers")
Cc: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Implement endpoint dequeue callback function.
Without this function, uboot will hang when executing fastboot comamnd.
See following flow:
"fastboot_tx_write_str->fastboot_tx_write->usb_ep_dequeue->ep->ops->dequeue"
without implement ci_udc dequeue function, ep->ops->dequeue is NULL, then
uboot will hang.
Tested on mx6qsabresd board with fastboot enabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Cc: "Łukasz Majewski" <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
By the time g_dnl_unbind() is run, cdev->config has been set to NULL,
so the free() there does nothing, and the config struct is leaked.
Equally, struct usb_gadget contains a linked list of config structs, so
the code should iterate over them all and free each one, rather than
freeing one particular config struct.
composite_unbind() already iterates over the list of config structs, and
unlinks each from the linked list. Fix this loop to free() each struct as
it's unlinked and otherwise forgotten.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Now that we have a new header file for cache-aligned allocation, we should
move the stack-based allocation macro there also.
Signed-off-by: Simon Glass <sjg@chromium.org>
port at91_udc driver from linux:
original commit Message:
commit c94e289f195e0e13cf34d27f9338d28221a85751
Author: Arnd Bergmann <arnd@arndb.de>
Date: Sat Apr 11 00:14:21 2015 +0200
usb: gadget: remove incorrect __init/__exit annotations
A recent change introduced a link error for the composite
printer gadget driver:
`printer_unbind' referenced in section `.ref.data' of drivers/built-in.o: defined in discarded section `.exit.text' of drivers/built-in.o
Evidently the unbind function should not be marked __exit here,
because it is called through a callback pointer that is not necessarily
discarded, __composite_unbind() is indeed called from the error path of
composite_bind(), which can never work for a built-in driver.
Looking at the surrounding code, I found the same problem in all other
composite gadget drivers in both the bind and unbind functions, as
well as the udc platform driver 'remove' functions. Those will break
if anyone uses the 'unbind' sysfs attribute to detach a device from a
built-in driver.
This patch removes the incorrect annotations from all the gadget
drivers.
Signed-off-by: Heiko Schocher <hs@denx.de>
When an EHCI device is registered in device mode, the HW isn't actually
initialized at all, and hence isn't left in a running state. Consequently,
when the device is deregistered, ehci_shutdown() will fail, since the HW
bits it expects to see set in response to its shutdown requests will not
be sent, and the message "EHCI failed to shut down host controller." will
be printed.
Fix ehci-hcd.c to remember whether the device was registered in host or
device mode, and only call ehci_shutdown() for host mode registrations.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Allocate request up to THOR_PACKET_SIZE not the ep0->maxpacket
as the descriptors data depend on the number of descriptors
and this 64 bytes were not enough and the buffer might overflow
which results in memalign failures later.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Dont perform reset at the end of thor download
if configured to do reset off.
Reset may not be required in all cases and hence
provided an option to do so.
The case would be to download the images to DDR instead
of flash device.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This is a convenient way for a driver to get the hardware address of a
device, when regmap or syscon are not being used. Change existing callers
to use it as an example to others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Drop the no longer accurate part of the USB_MUSB_SUNXI Kconfig help text,
since the musb-host code now supports the device-model, ehci and musb in
host mode can both be enabled at the same time without issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Added support to power on/power off the second USB PHY present in
DRA7xx and AM57xx.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Writing "0x00" to the USBOTGSS_IRQENABLE_SET_MISC and
USBOTGSS_IRQENABLE_SET_0 doesn't disable the interrupts. Used
USBOTGSS_IRQENABLE_CLR_MISC and USBOTGSS_IRQENABLE_CLR_0 instead.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cleaning up order of include files by sorting them alphabetically
keeping in mind to leave common.h on top.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
This driver is not used only on exynos, but also on Altera SoCFPGA,
HiSilicon SoCs, RPi etc, so rename it accordingly to prevent confusion.
Signed-off-by: Marek Vasut <marex@denx.de>
populate _reset_ callback to the USB ethernet gadget since UDC core
expects every gadget driver to have the reset callback. This shouldn't
be needed once the ethernet gadget driver is adapted to use the
composite driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
xhci omap driver has board_usb_init in xhci_hcd_init but doesn't have
the corresponding cleanup function in xhci_hcd_stop.
Fix it here by invoking board_usb_cleanup() in xhci_hcd_stop().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Ethernet gadget driver can be used both by both SPL and u-boot. Since
usb_eth_init() is the entry point for ethernet gadget driver, perform
board initialization there. Also perform the cleanup in usb_eth_halt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This patch fixes a potential NULL pointer dereference arising on
non-present/non-initialized xHCI controllers and adds some error
handling to xHCI code
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Document target board specific functions
board_ehci_hcd_init - override usb phy mode
board_ehci_hcd_init - set usb vbus voltage
board_ehci_power - enables/disables usb vbus voltage
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
This patch adds support for multiple hostcontrollers to the ehci-marvell driver
and enables all 3 usb-hcs on the db-mv784mp-gp board.
It depends on the initial Armada XP usb support patch from Stefan.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables the USB EHCI support for the Marvell Armada XP (AXP)
SoCs. In compatism to the Armada 38x (A38x), the AXP needs to configure
the USB PLL and the USB PHY's specifically in U-Boot. The A38x has done
this already in the bin_hdr (SPL U-Boot). Without this, accessing the
controller registers in U-Boot or Linux will hang the CPU.
Additionally, the AXP uses a different USB EHCI base address. This
patch also takes care of this by runtime SoC detection in the Marvell
EHCI driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Remove the CONFIG_DM_USB limitation to enable cache support functions.
Tested on SAMA5D3x-EK board.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
This adds dcache support for dwc2. The DMA buffers must be DMA aligned and
is flushed for outgoing transactions before starting transfer. For
ingoing transactions it is invalidated after the transfer has finished.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Update to apply again on top of DM patches]
Signed-off-by: Tom Rini <trini@konsulko.com>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
At present struct eth_device is passed around all over the place. This does
not exist with driver model. Add explicit arguments instead, so that with
driver model we can pass the correct things.
Signed-off-by: Simon Glass <sjg@chromium.org>
The AX_ prefix comes from the Asix driver. Since this is not that, we should
avoid this confusing prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put all global data in a structure and move (what will be) common code into
common functions. This will make the driver-model conversion much easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs
to be measured - should be close to 700MHz (1.4G/2).
Note that some freqs aren't in the PLLU table in T210 TRM
(13, 26MHz), so I used the 12MHz table entry for them. They
shouldn't be selected since they're not viable T210 OSC freqs.
Since there are now 2 new OSC defines, all tables (pll_x_table,
PLLU) had to increase by two entries, but since 38.4/48MHz are
not viable osc freqs on T20/30/114, etc, they're just set to 0.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch fixes operation of our on-board AX88772B chip without EEPROM
but with a ethaddr coming from the regular U-Boot environment. This is
a forward port of some remaining parts initially implemented by
Antmicro.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
usb_stor_reset is only defined when USB storage support is enabled, thus the
function is not declared when such support is missing.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Currently, the second use of a gadget will fail, while the first one works.
Forcing the EP0 at every enable fix this issue.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.
In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Having MUSB_HOST and MUSB_GADGET in Kconfig allows more flexibility with regard
to what Kconfig options to enable, such as USB_STORAGE or USB_KEYBOARD.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
There is no particular reason why the USB Kconfig option should be specific to
host mode. In prevision of adding MUSB host and gadget to Kconfig, this moves
the title and help message of the USB Kconfig option to a more generic format.
Adding comments to the usb Kconfig allows for a better separation and more
readability in generated configs and in menuconfig.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The USB_ARCH_HAS_HCD currently serves no purpose and adds some confusion to the
required Kconfig options that are required to have USB support.
Dropping it makes things easier and doesn't break anything, since it was unused
anyways.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This patch makes the dwc2 controller like ehci / ohci / xhci controllers
by calling the board_usb_init() function from usb_lowlevel_init.
This can then be implemented by specific platforms to initialise
their USB hardware (phys / clocks etc).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
With recent additions to USB Kconfig the number of USB options had grown
large enough to warrant a separate menu for USB.
Add a Kconfig menu for USB.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add Kconfig options for USB keyboard and use them for cm-fx6.
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb
config to defconfig.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When we return an error the usb core will print an error-message, so in this
case do not print anything.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The ci_udc driver request allocation assumes that the endpoint descriptor
pointer is set to retrieve the endpoint number, but that is only true
when the endpoint is enabled. This results in a NULL ptr dereference
which for me happens to return 0 value. This causes the EP0 request
struct to be returned for other endpoints. Some gadget drivers like
fastboot and USB MS work fine, but ethernet does not.
Really, the ci_udc driver is the oddball here doing this EP0 special
case handling Stephen added. All the other drivers alloc/free functions
are pretty much the same with the only variation being the size of the
private struct. This could all be consolidated to a common function.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Stephen Warren <swarren@nvidia.com>
The macro cpu_relax() is defined by several headers in different
ways.
arch/{arm,avr32,mips}/include/asm/processor.h defines it as follows:
#define cpu_relax() barrier()
On the other hand, include/linux/compat.h defines it as follows:
#define cpu_relax() do {} while (0)
If both headers are included from the same source file, the warning
warning: "cpu_relax" redefined [enabled by default]
is displayed.
It effectively makes it impossible to include <linux/compat.h>
from some sources. Drop the latter.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This patch removes the wrl accessor function from the Marvell EHCI
driver by replacing it with the writel function.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
FASTBOOT is defined both by CONFIG_USB_FUNCTION_FASTBOOT AND CONFIG_CMD_FASTBOOT, so it doesn't
make much sense to have a CONFIG_USB_FASTBOOT prefix for fastboot-specific options, especially
given that other config options for fastboot use the CONFIG_FASTBOOT prefix.
This replaces the CONFIG_USB_FASTBOOT prefix with CONFIG_FASTBOOT, for consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Add the required files for the Broadcom UDC OTG interface.
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Recent versions of the fastboot tool will query the partition type before doing
an operation on a partition (such as erase, flash, etc). It will then submit
the operation as soon as the response for the partition type is received.
Usually, the MUSB controller will see that the partition type request return
status was read by the host at the very same time as the actual operation
request is submitted by the host. However, the operation will be read first
(int_rx is handled first in musb_interrupt) and after it is completed, the
fastboot USB gadget driver will send another return status. Hence, this happens
before the musb gadget framework has had a chance to handle the previous
acknowledgement that the host read the return status and dequeue the request.
The host will then usually empty the FIFO by the time musb_interrupt gets around
handling the return status acknowledgement (for the previous request, this is
still on the same musb_interrupt call), so no other interrupt is generated and
the most recent return status acknowledgement remains unaccounted for.
It will then be used as a response for the next command, and the proper response
for it will be delayed to the next command, and so on.
Dequeuing the previous IN request in the fastboot code ensures that no previous
return status remains. It is acceptable to do it since there is no callback to
it anyways.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This avoids handling requests that have an error status or no data.
In particular, this avoids showing unnecessary error messages when the USB
gadget gets disconnected (e.g. with fastboot continue) and the fastboot USB
gadget driver sends an error back to the host (that has disconnected already).
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Weak versions of board_usb_init and board_usb_cleanup are defined in common USB
host code, but it is also used for USB device gadgets, so we also need a weak
definition of it when there is no USB host enabled.
Both weak definitions do not conflict.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
USB download gadget functions such as thor and dfu have a separate config option
for the USB gadget part of the code, independent from the command part.
This switches the fastboot USB gadget to the same scheme, for better
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
This introduces a coherent scheme for naming USB download gadget and functions
config options. The download USB gadget config option is moved to
CONFIG_USB_GADGET_DOWNLOAD for better consistency with other gadgets and each
function's config option is moved to a CONFIG_USB_FUNCTION_ prefix.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Test HW: Odroid_XU3 (Exynos5422), trats (Exynos4210)
Remove LS102XA immap header inclusion from xhci fsl driver.
It removes redefinition warnings when built for platforms
other than LS102XA
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
This adjusts (micro)frame length to appropriate value thus
avoiding USB devices to time out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
This USB Ethernet driver is quite widely use. Allow it to work with
CONFIG_DM_ETH enabled. Most of the code remains common but there is a new
packet receive flow which is handled specially.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support driver model in this driver. This uses the normal USB driver search
mechanism. Any EHCI controllers will be set up as they are found during
usb_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
In Linux USB_DEVICE() is used to declare a USB device by vendor/device ID.
We should follow the same convention in U-Boot. Rename the existing
USB_DEVICE() macro to U_BOOT_USB_DEVICE() and bring in the USB_DEVICE()
macro from Linux for use in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present USB Ethernet does not work with CONFIG_DM_ETH. Add driver model
support to this feature, so that it can work alongside other Ethernet
devices with driver model.
It was found that quite a bit of code is common in most of the USB Ethernet
drivers. Add this code to the common layer to reduce the amount of duplicate
code needed in USB Ethernet drivers when CONFIG_DM_ETH is used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add device-model support to the musb-host u-boot glue, note this only
adds device-model support to the musb-core glue code, it does not add
support for device-model to any of the SoC specific musb glue code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a musb_host_data struct to hold all the global data host related musb
data. This is a preparation patch for adding device-model support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Rename and wrap the usb host API public functions, this is a preparation
patch for adding device-model support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
When building with CONFIG_DM_USB=y struct usb_device does not have a parent
pointer. This commit adds support to the musb code to deal with this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Allow musb_platform_enable to return an error code and propagate it up to
usb_lowlevel_init().
This allows moving the checks for an external vbus being present to be
moved from platform_init to platform_enable, so that the user can unplug a
charger, plug in a host adapter with a usb-device, do a "usb reset" and
have things working.
This also allows adding a check for the id-pin to platform_enable, so that
it can short circuit the 1s delay in usb_lowlevel_init() when no host cable
is plugged in and thus waiting for a device to show up is useless.
Note that all the changes to code shared with the kernel are wrapped in
the kernel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
On some single port (otg) controllers there is no emulated root hub, so
the first child (if any) may be one of: UCLASS_MASS_STORAGE,
UCLASS_USB_DEV_GENERIC or UCLASS_USB_HUB.
All three of these (and in the future others) are suitable for our
purposes, remove the check for the device being a hub, and add a check to
deal with the fact that there may be no child-dev.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Allow usb uclass host drivers to implement usb_reset_root_port, this is
used by single port usb hosts which do not emulate a hub, such as otg
controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now that we unbind usb devices from usb_stop() usb_find_child() is
only necessary to deal with emulated usb devices.
Rename it to make this clear and add a #ifdef to make it a nop in
other cases.
Note the #ifdef turns usb_find_emul_child() into a nop, rather then not
building it and adding another #ifdef to the caller, this is done this way
because adding a #ifdef to the caller is somewhat hairy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
On an usb stop instead of leaving orphan usb devices behind simply remove
them.
The result of this commit is best seen in the output of "dm tree" after
plugging out an usb hub with 2 devices plugges in and plugging in a keyb.
instead, before this commit the output would be:
usb [ + ] `-- sunxi-musb
usb_hub [ ] |-- usb_hub
usb_mass_st [ ] | |-- usb_mass_storage
usb_dev_gen [ ] | `-- generic_bus_0_dev_3
usb_dev_gen [ + ] `-- generic_bus_0_dev_1
Notice the non active usb_hub child and its 2 non active children. The
first child being non-active as in this example also causes usb_get_dev_index
to return NULL when probing the first child, which results in the usb kbd
code not binding to the keyboard.
With this commit in place the output after swapping and "usb reset" is:
usb [ + ] `-- sunxi-musb
usb_dev_gen [ + ] `-- generic_bus_0_dev_1
As expected, and usb_get_dev_index works properly and the keyboard works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add an usb_device parameter to usb_reset_root_port so that it knows which
root-port it is resetting. This is necessary for proper device-model support
for usb_reset_root_port.
Also remove a duplicate declaration of usb_reset_root_port() from usb.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop the unneeded portnr function argument, the portnr is part of the
usb_device struct which is passed via the dev argument.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The device-model usb_legacy_port_reset function calls the device-model
usb_port_reset function which is a 1 on 1 copy of the non dm
usb_legacy_port_reset and this is the only use of usb_port_reset in all
of u-boot.
Drop both, and alway use the usb_legacy_port_reset() version in
common/usb.c .
Also while at it make it static as it is only used in common/usb.c .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Without this we loose every other interrupt packet. We never noticed this
because with keyboards the packets which we were loosing would normally
be key release packets.
But now that we do keyrepeat in software instead of relying on the hid
idle functionality, missing a release will result in key repeat triggering.
This commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Remove the unused sunxi_musb_exit method, there is no code in u-boot
calling the exit method, and our implementation was broken as it did
not disable the clocks and asserted reset.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Fully resetting the controller is a too big hammer, and the musb_core will
then afterwards fail to communicate with any endpoints other then 0 as
too much state was cleared.
Instead report vbus low for 200ms which will effectively end the current
session without needing to do a full reset.
This fixes usb mass-storage devices no longer working after a "usb reset"
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This change decreases the interval of calls to:
- display busy indicator
- check ctrlc()
- check cable connection
By this change, breaking the UMS command is more easy on Odroid XU3.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
New files, namely samsung_usb_phy.c and samsung-usb-phy-uboot.h have
been added to u-boot to provide proper PHY handling at Exynos5 SoCs.
This code is used thereafter in the board_usb_init() call.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Add a weak function board_ehci_hcd_init which can be used by the board
file for board specific initialisation.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Return if USB_MAX_CONTROLLER_COUNT hence the index of the controller
to be initialised is incorrect
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
The business for UniPhier Soc family has been transferred from
Panasonic Corporation to Socionext Inc.
Update the SoC select menu in Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
In the Linux coding style, it is recommended to include <linux/io.h>
rather than <asm/io.h>. Follow this trend.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This has been tested to the extent that I can enumerate
a asix usb networking adapter and boot a kernel over usb
on the 96boards hikey u-boot port I'm currently doing.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Update the ci_udc driver to support bulk transfer
and also added capability of having multiple dtds
if requested data is more than 16K.
These changes are tested for both the DFU and lthor.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Add support for interrupt queues to the ohci hcd code, bringing it inline
with the ehci and musb-new(host) code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add an ohci_alloc_urb() function, this is a preparation patch for adding
interrupt queue support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
When submitting interrupt packets to an endpoint we only link in the ed
once to avoid some races surrounding unlinking of periodic endpoints,
but we share one ohci_device struct / one set of ed-s for all devices,
which means that if we have an interrupt endpoint at endpoint 1 with one
device, and a non interrupt endpoint 1 with another device we end up
with the same ed linked into both the periodic and async lists, which is
not good (tm).
This commit switches over to using separate ohci_device structs, and thus
separate ed-s for devices with interrupt endpoints, fixing this.
This fixes e.g. matching a usb storage device and keyboard on the same
usb-1 hub not working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This commit adds support for the OHCI companion controller, which makes
usb-1 devices directly plugged into to usb root port work.
Note for now this switches usb-keyboard support for sunxi back from int-queue
support to the old interrupt polling method. Adding int-queue support to the
ohci code and switching back to int-queue support is in the works.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Convert sunxi-boards which use the sunxi-ehci code to the driver-model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
For some reason the ohci code is full with:
#ifdef DEBUG
pkt_print(...)
#else
mdelay(1);
#endif
AFAICT there is no reason for the mdelay(1) calls. This commit disables them
when building the ohci code for new driver-model using boards. It leaves
the mdelay(1) calls in place when building for older boards, so as to avoid
causing any regressions there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The usb spec says that we must wait a minimum amount of time after port
power on (exact time is in the hub descriptor), this is something which
we must not only do for root ports but also for external hub ports, which
is why the common usb_hub code already waits a full second after powering
up ports. Having a separate wait for just the root hub in the ohci-hcd
code only leads to doing the waiting twice for the root ports, so drop the
wait from the ohci-hcd code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The u-boot usb code uses polling for all endpoints, including interrupt
endpoints, so urbs should never be automatically resubmitted.
This also fixes a leak of the urb, as submit_int_msg() did not check if
an already re-submitted urb exists before creating a new one.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
USB scanning is slow, and there is no need to scan the companion buses
if no usb devices where handed over to the companinon controllers by any
of the main controllers.
This saves e.g. 2 seconds when booting a A10 OLinuxIno Lime with no USB-1
devices plugged into the root usb ports.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
USB companion controllers must be scanned after the main controller has
been scanned, so that any devices which the main controller which to hand
over to the companion have actually been handed over before we scan the
companion.
As there are no guarantees that this will magically happen in the right
order, split the scanning of the buses in 2 phases, first main controllers,
and then companion controllers.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move printing of usb scan status to usb_scan_bus().
This is a preparation patch for adding companion controller support to the
usb uclass.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Interrupt endpoints typically are polled for a long time by the usb
controller before they return anything, so calls to submit_int_msg() can
take a long time to complete this.
To avoid this the u-boot code has the an interrupt queue mechanism / API,
add support for this to the driver-model usb code and implement it for the
dm ehci code.
See the added doc comments for more details.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
This is a preparation patch for adding interrupt-queue support to the
ehci dm code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Short circuit the retry loop in legacy_hub_port_reset() by returning an
error from usb_control_msg() when a device was handed over to a companion
by the ehci code. This avoids trying to reset low / fullspeed devices 5
times needlessly. Also do not print an error when a device has been handed
over.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
When after a reset the port status connection bit is still set and the enable
bit is not then we're dealing with a full-speed device and should hand it over
to the companion controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Interrupts transfers timing out is normal, so do not log an error for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Add proper cache flushing / invalidating for non cache coherent cpus, for now
only enable this for new (driver-model) usb code to avoid regressions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Non static function and variable declarations do not belong in a .h file.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
This is a preparation patch for adding driver-model support.
Note we do keep ohci_dev as a separate struct so that we can later add
support for interrupt-queues which requires allocating a separate ohci_dev
per interrupt-queue.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
devgone is never assigned a value, so the one comparisson reading it will
never be true, and devgone can be completely removed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Marek Vasut <marex@denx.de>
Without this usb-1 device descriptors do not get read properly.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
The ehci driver model code for finding the first upstream usb-2 hub before
this commit has a number of issues:
1) "if (!ttdev->speed != USB_SPEED_HIGH)" does not work because the '!'
takes presedence over the '!=' this should simply be
"if (ttdev->speed == USB_SPEED_HIGH)"
2) It makes ttdev point to the first upstream usb-2 hub, but ttdev should
point to the last usb-1 device before the first usb-2 hub (when going
upstream from the device), as ttdev is used to find the port of the
first usb-2 hub to which the the last usb-1 device is connected.
3) parent_devnum however should be set to the devnum of the first usb-2
hub, so we need to keep pointers around to both usb_device structs.
To complicate things further during enumeration usb_device.dev will point
to the parent udevice, where as during normal use it will point to
the actual udevice, we must handle both cases correctly.
This commit fixes all this making usb-1 devices attached to usb-2 hubs,
including usb-1 devices attached to usb-1 hubs attached to usb-2 hubs, work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use usb_get_bus in dm ehci code rather then re-implementing it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently we copy over a number of usb_device values stored in the on stack
struct usb_device probed in usb_scan_device() to the final driver-model managed
struct usb_device in usb_child_pre_probe() through usb_device_platdata, and
then call usb_select_config() to fill in the rest.
There are 3 problems with this approach:
1) It does not fill in enough fields before calling usb_select_config(),
specifically it does not fill in ep0's maxpacketsize causing a div by zero
exception in the ehci driver.
2) It unnecessarily redoes a number of usb requests making usb probing slower
3) Calling usb_select_config() a second time fails on some usb-1 devices
plugged into usb-2 hubs, causing u-boot to not recognize these devices.
This commit fixes these issues by removing (*) the usb_select_config() call
from usb_child_pre_probe(), and instead of copying over things field by field
through usb_device_platdata, store a pointer to the in stack usb_device
(which is still valid when usb_child_pre_probe() gets called) and copy
over the entire struct.
*) Except for devices which are explictly instantiated through device-tree
rather then discovered through usb_scan_device() such as emulated usb devices
in the sandbox.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Make usb_get_bus easier to use for callers, by directly returning the bus
rather then returning it via a pass-by-ref argument.
This also removes the error checking from the current callers, as
we already have an assert() for bus not being NULL in usb_get_bus().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Do not use bus->seq before device_probe(bus), as bus->seq is not set until
after the device_probe() call. This fixes u-boot printing: "USB-1: " for
each bus it scans.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.
Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.
Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.
This patch purely renames things, it contains no functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.
This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.
This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable full support for the A33 SoC including display, otg-usb, etc.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The terminator is missing. Add it for completeness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Joe Hershberger <joe.hershberger@ni.com>
Check if USB Erratum A005697 is applicable on BSC913x and
add corresponding property in the device tree via device
tree fixup which is used by linux driver
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Identify soc(s) having dual phy so as to add "utmi_dual" as phy_mode
for all these socs. This is required for supporting deel-sleep feature
in linux for usb driver
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.
This cleans up the temporary hacks that were added to this interface
along with the DM support.
This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add driver model support in the XHCI support code so that it can be used by
XHCI USB drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Since driver model will want to use most of the same code for XHCI init
and uninit, put it in a separate function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This function should not be delving into struct usb_device. Pass in the
parameters it needs directly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Rather than getting this directly from struct usb_device, call a function
to obtain it. This will make it possible for driver model to provide it
another way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
We want to use mostly the same init and uninit code for driver model, so move
the common part into two functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Try to return useful error numbers where possible. Also avoid swallowing
an error number when it is returned by a called function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This variable is a bit of a hack. We can obtain the same information from
the normal device config. This will fit better with driver model, where
global variables are best avoided.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add support for scanning USB etghernet devices with driver model. This mostly
involves scanning all buses since device numbering is not unique across
buses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This driver supports using emulation devices to provide a USB bus within
sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
All USB controllers need a root hub. Add a sandbox emulation for this so
that we can add USB devices to sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
This emulator supports USB enumeration and allows a local file to be provided
as the contents of the emulated flash stick. U-Boot can then use the file as
it would a normal device, with all access passing through the usb_stor layer
and the USB stack.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These devices must have their addresses removed ready for the next USB
bus enumeration. Add this logic to usb_stop().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With sandbox we want to be able to emulate USB devices so that we can test
the USB stack. Add a uclass to support this. It implements the same
operations as a normal USB device driver, but in this case passes them on
to an emulation driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Some controllers support OTG (on-the-go) where they can operate as either
host or device. The gadget layer in U-Boot supports this.
While this layer does not interact with driver model, we can provide a
function which sets up the controller in the correct way. This way the code
at least builds (although it likely will not work).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
At present USB devices with no driver model driver cannot be seen in the
device list, and we fail to set them up correctly. This means they cannot
be used.
While having real drivers that support driver model for all USB devices
is the eventual goal, we are not there yet.
As a stop-gap, add a generic USB driver which is bound when we do not have
a real driver. This allows the device to be set up and shown on the bus.
It also allows ad-hoc code (such as usb_ether) to find these devices and
set them up.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
USB devices in U-Boot are currently probed only after all devices have
been enumerated. Each type of device is probed by custom code, e.g.:
- USB storage
- Keyboard
- Ethernet
With driver model this approach doesn't work very well. We could build
a picture of the bus and then go back and add the devices later, but
this means that the data structures are incomplete for quite a while.
It also does not follow the model of being able to bind a device when we
discover it.
We would prefer to have devices automatically be bound as the device is
enumerated. This allows us to attach drivers to particular USB classes
or product/vendor IDs. This is the method used by Linux.
Add the required #defines from Linux, a way of declaring a USB driver and
the logic to locate the correct driver given the USB device's descriptors.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Add a way for EHCI controller drivers to support driver model. Drivers can
call ehci_register() to register themselves in their probe() methods.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
The index cannot be used with driver model, and isn't needed anyway. Change
the parameter to a pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
These are a pain with driver model because we might have different EHCI
drivers which want to implement them differently. Now that they use
consistent function signatures, we can in good conscience move them to
a struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Fix non-driver-model EHCI to set up the EHCI operations correctly:
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the bulk of the code in usb_lowlevel_init() into a separate function
which will also be used by driver model. Keep the CONFIG options out of
this function by providing a tweak flag for Faraday. We need to avoid using
CONFIG options in driver model code where possible, since it makes it
impossible to use multiple controllers in that code where they have
different options.
The CONFIG_EHCI_HCD_INIT_AFTER_RESET option is also kept out of the
common init function. With driver model the controller will be able to
perform this extra init itself after registering with the EHCI layer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
With driver model we want to remove the controller pointer in struct udevice
and use driver model data structures instead. To prepare for this, move
access to this field to a function which can provide a different
implementation for driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
