default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
The STM32MP ROM provides several service. One of them is the ability
to verify ecdsa256 signatures. Hook the ROM API into the ECDSA uclass.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The function board_get_usable_ram_top can be called after relocation
with total_size = 0 to get the uppermost pointer that is valid to access
in U-Boot.
When total_size = 0, the reserved memory should be not take in account
with lmb library and 'gd->ram_base + gd->ram_size' can be used.
It is the case today in lib/efi_loader/efi_memory.c:efi_add_known_memory()
and this patch avoids that the reserved memory for OP-TEE is not part of
the EFI available memory regions.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The MTD tee partitions used to save the OP-TEE binary are needed when
TF-A doesn't use the FIP container to load binaries.
This patch puts under CONFIG_STM32MP15x_STM32IMAGE flag the associated
code in U-Boot binary and prepare the code cleanup when
CONFIG_STM32MP15x_STM32IMAGE support will be removed after TF-A migration
to FIP support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
With FIP support in TF-A (when CONFIG_STM32MP15x_STM32IMAGE
is not activated), the DT nodes needed by OP-TEE are added by OP-TEE
firmware in U-Boot device tree, present in FIP.
These nodes are only required in trusted boot, when TF-A load the file
u-boot.stm32, including the U-Boot device tree with STM32IMAGE header,
in this case OP-TEE can't update the U-Boot device tree.
Moreover in trusted boot mode with FIP, as the OP-TEE nodes are present
in U-Boot device tree only when needed the function
stm32_fdt_disable_optee can be removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
By default for trusted boot with TF-A, U-Boot (u-boot-nodtb)
is located in FIP container with its device tree and with
the secure monitor (provided by TF-A or OP-TEE).
The FIP file is loaded by TF-A BL2 and each components is
extracted at the final location.
This patch add CONFIG_STM32MP15x_STM32IMAGE to request the
STM32 image generation for SOC STM32MP15x
when FIP container is not used (u-boot.stm32 is loaded by TF-A
as done previously to keep the backward compatibility).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
OP-TEE is very particular about how the TZC should be configured.
When booting an OP-TEE payload, an incorrect TZC configuration will
result in a panic.
Most information can be derived from the SPL devicetree. The only
information we don't have is the split between TZDRAM and shared
memory. This has to be hardcoded. The rest of the configuration is
fairly easy, and only requires 3 TZC regions. Configure them.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
The purpose of this change is to allow configuring TrustZone (TZC)
memory permissions. For example, OP-TEE expects TZC regions to be
configured in a very particular way. The API presented here is
intended to allow exactly that.
UCLASS support is not implemented, because it would not be too useful.
Changing TZC permissions needs to be done with care, so as not to cut
off access to memory we are currently using. One place where we can
use this is at the end of SPL, right before jumping to OP-TEE.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
When the TAMP register 20 have an invalid value (0x0 for example after
TAMPER error) the "boot_device" U-Boot env variable have no value and
no error is displayed in U-Boot log.
The STM32MP boot command bootcmd_stm32mp failed with strange trace:
"Boot over !"
and the next command in bootcmd_stm32mp failed with few indication:
if test ${boot_device} = serial || test ${boot_device} = usb;
then stm32prog ${boot_device} ${boot_instance};
As it is difficult to investigate, the current patch avoids this issue:
- change the debug message to error: "unexpected boot mode" is displayed
- display trace "Boot over invalid!" in bootcmd_stm32mp
- execute "run distro_bootcmd" to try all the possible target
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the device sequence number in boot_instance variable
and no more the SDMMC instance provided by ROM code/TF-A.
After this patch we don't need to define the mmc alias in
device tree, for example:
mmc0 = &sdmmc1;
mmc1 = &sdmmc2;
mmc2 = &sdmmc3;
to have a correct mapping between the ROM code boot device =
"${boot_device}${boot_instance}" and the MMC device in U-Boot.
With this patch the 'mmc0' device (used in mmc commands) is
always used when only one instance sdmmc is activated in device
tree, even if it is only the sdmmc2 or sdmmc3.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the existing defines PMIC_SIZE and OTP_SIZE and a new define
CMD_SIZE for virtual partition size.
This patch corrects the size for OTP partition in alternate name
(1024 instead of 512) and avoids other alignment issues.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable the clocks during syscon probe when they are present in device tree.
This patch avoids a freeze when the SYSCFG clock is not enabled by
TF-A / OP-TEE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The expected sequence to close the device
1/ Load key in DDR with any supported load command
2/ Update OTP with key: STM32MP> stm32key read <addr>
At this point the device is able to perform image authentication but
non-authenticated images can still be used and executed.
So it is the last moment to test boot with signed binary and
check that the ROM code accepts them.
3/ Close the device: only signed binary will be accepted !!
STM32MP> stm32key close
Warning: Programming these OTP is an irreversible operation!
This may brick your system if the HASH of key is invalid
This command should be deactivated by default in real product.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Allow to read the OTP value and lock status with the command
$> stm32key read.
This patch also protects the stm32key fuse command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add a helper function to access to BSEC misc driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Lock the OTP value of key's hash after the command
$> stm32key fuse <address>
This operation forbids a second update of these OTP as they are
ECC protected in BSEC: any update of these OTP with a different value
causes a BSEC disturb error and the closed chip will be bricked.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Simplify parsing the command argument by using
the macro U_BOOT_CMD_WITH_SUBCMDS.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This command is used to evaluate the secure boot on stm32mp SOC,
it is deactivated by default in real products.
We activate this command only in STMicroelectronics defconfig
used with the evaluation boards.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reduce the content of short help message for stm32prog command and
removed the carriage return to fix the display of 'help' command when
this command is activated.
Fixes: 954bd1a923 ("stm32mp: add the command stm32prog")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Move the message "Invalid or missing layout file."
to debug level as it is a normal behavior and not an error
and add the missing '\n'.
This patch avoids the strange trace :
Boot over usb0!
Invalid or missing layout file.DFU alt info setting: done
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use get_cpu_dev() in uart getID command and remove the defines
DEVICE_ID_BYTE1 and 2 defines.
This patch prepare the support for new SOC family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle number of alternate when DM_PMIC is not activated.
This patch remove the last UNKNOWN partition in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Handle the second USB enumeration only when the flashlayout is received
and when phase is PHASE_FLASHLAYOUT. This patch removes the call of
stm32prog_next_phase as it is already done in stm32prog_dfu_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When CONFIG_FIT_SIGNATURE is activated, CONFIG_LEGACY_IMAGE_FORMAT
is deactivated and the define IMAGE_FORMAT_LEGACY don't exist with
include/image.h:
#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
#define IMAGE_FORMAT_LEGACY 0x01 /* legacy image_header based format */
#endif
This patch adds the needed check on compilation flag
CONFIG_LEGACY_IMAGE_FORMAT to avoid the compilation error
for command stm32prog:
cmd_stm32prog.c:81:8: error: ‘IMAGE_FORMAT_LEGACY’ undeclared
(first use in this function); did you mean ‘IMAGE_FORMAT_FIT’?
81 | if (IMAGE_FORMAT_LEGACY ==
| ^~~~~~~~~~~~~~~~~~~
| IMAGE_FORMAT_FIT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support in command stm32prog of kernel load and start
with initrd file, identify by the partition Type "Binary" in
the flashlayout.tsv, for example:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 board.dtb
P 0x12 initrd Binary ram0 0xC4400000 <initrd>
The <initrd> file can be a legacy image "uInitrd", generated
with mkimage, or a RAW initrd image "initrd.gz".
After a DFU detach the bootm command with be executed
with the associated address, for example:
$> bootm 0xC2000000 0xC4400000:<size> 0xC4000000
When the "Binary" partition type is absent, the 'bootm'
command starts the kernel without ramdisk, for example:
$> bootm 0xC2000000 - 0xC4000000
With this paths, it is no more mandatory to generate FIT
including the kernel, DT and initrd:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 fit System ram0 0xC2000000 fit.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle timeout in stm32prog_serial_get_buffer to sent NACK
to STM32CubeProgrammer when the buffer is not fully received.
This patch avoids to reach the STM32CubeProgrammer timeout and
the associated unrecoverable error.
Timeout error occurred while waiting for acknowledgment.
Error: Write Operation fails at packet number 4165 at address 0x1044FF
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch removes the header check for UART download;
the check of checksum is not mandatory with even parity and chuck
checksum for each 256 received bytes and it is only done for
STM32 image (FSBL = TF-A BL2), not for FIT image.
This patch solve issue of duplicated 0x100 byte written with FIP header.
Fixes: 4fb7b3e108 ("stm32mp: stm32prog: add FIP header support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
No more map the reserved region with "no-map" property by marking
the corresponding TLB entries with invalid entry (=0) to avoid
speculative access.
The device tree parsing done in lmb_init_and_reserve() takes a
long time when it is executed without data cache, so it is called in
enable_caches() before to disable it.
This patch fixes an issue where predictive read access on secure DDR
OP-TEE reserved area are caught by firewall.
Series-cc: marex
Series-cc: pch
Series-cc: marek.bykowski@gmail.com
Series-cc: Ard Biesheuvel <ardb@kernel.org>
Series-cc: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add 8M for the U-Boot reserved memory (display, fdt, gd, ...)
mapped cacheable before relocation.
Without this patch the device tree, located before the MALLOC area
is not tagged cacheable just after relocation, before mmu reconfiguration.
This patch reduces the duration for device tree parsing in
lmb_init_and_reserve.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
-----BEGIN PGP SIGNATURE-----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=4VxR
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210409' of https://source.denx.de/u-boot/custodians/u-boot-stm
Add rt-thread art-pi board support based on STM32H750 SoC
Add Engicam i.Core STM32MP1 SoM
Add FIP header support for STM32programmer
Update uart number when no serial device found for STM32MP1
Remove board_check_usb_power function when ADC flag is not set
Update SPL size limitation for STM32MP1
Set soc_type, soc_pkg, soc_rev env variables for STM32MP1
Split up get_soc_name(), clean the decoding up a bit, and set up
environment variables which contain the SoC type, package, revision.
This is useful on SoMs, where multiple SoC options are populated.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Replace the remaining printf in setup_boot_mode() by log macro
to handle filtering for log features.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Align the uart number in the trace of setup_boot_mode() with the name of
the uart/usart device (start at 1) and not with the instance value
(start at 0), i.e. the serial device sequence number and the index in
serial_addr[].
Fixes: f49eb16c17 ("stm32mp: stm32prog: replace alias by serial
device sequence number")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support of TF-A FIP header in command stm32prog for all the boot
partition and not only the STM32IMAGE.
This patch is a preliminary patch to support FIP as second boot stage
after TF-A BL2 when CONFIG_TFABOOT is activated for trusted boot chain.
The FIP is archive binary loaded by TF-A BL2, which contains the secure OS
= OP-TEE and the non secure firmware and device tree = U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
7" OF is a capacitive touch 7" Open Frame panel solutions with
- 7" AUO B101AW03 LVDS panel
- EDT, FT5526 Touch
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
MicroGEA STM32MP1 needs to mount on top of MicroDev 2.0 board with
pluged 7" OF for creating complete MicroGEA STM32MP1 MicroDev 2.0
7" Open Frame Solution board.
Linux dts commit details:
commit <1d278204cbaa> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 7" OF")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
MicroDev 2.0 is a general purpose miniature carrier board with CAN,
LTE and LVDS panel interfaces.
Genaral features:
- Ethernet 10/100
- USB Type A
- Audio Out
- microSD
- LVDS panel connector
- Wifi/BT (option)
- UMTS LTE with sim connector (option)
MicroGEA STM32MP1 is a STM32MP157A based Micro SoM.
MicroGEA STM32MP1 needs to mount on top of this MicroDev 2.0 board
for creating complete MicroGEA STM32MP1 MicroDev 2.0 Carrier board.
Linux dts commit details:
commit <f838dae7afd0> ("ARM: dts: stm32: Add Engicam MicroGEA STM32MP1
MicroDev 2.0 board")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam C.TOUCH 2.0 is an EDIMM compliant general purpose Carrier
board.
Genaral features:
- Ethernet 10/100
- Wifi/BT
- USB Type A/OTG
- Audio Out
- CAN
- LVDS panel connector
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Carrier board for
creating complete i.Core STM32MP1 C.TOUCH 2.0 board.
Linux dts commit details:
commit <6ca2898df59f> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
C.TOUCH 2.0")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board.
Genaral features:
- LCD 7" C.Touch
- microSD slot
- Ethernet 1Gb
- Wifi/BT
- 2x LVDS Full HD interfaces
- 3x USB 2.0
- 1x USB 3.0
- HDMI Out
- Mini PCIe
- MIPI CSI
- 2x CAN
- Audio Out
i.Core STM32MP1 is an EDIMM SoM based on STM32MP157A from Engicam.
i.Core STM32MP1 needs to mount on top of this Evaluation board for
creating complete i.Core STM32MP1 EDIMM2.2 Starter Kit.
Linux dts commit details:
commit <adc0496104b6> ("ARM: dts: stm32: Add Engicam i.Core STM32MP1
EDIMM2.2 Starter Kit")
Add support for it.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPI Load isn't mandatory for STM32 builds.
Let's imply instead of select it to get rid of build
issues for non-SPI defconfigs.
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Fix following compilation issue when SYS_DCACHE_OFF and/or SYS_DCACHE_SYS
are enabled :
arch/arm/mach-stm32mp/cpu.c: In function ‘early_enable_caches’:
arch/arm/mach-stm32mp/cpu.c:223:10: error: ‘volatile struct arch_global_data’ has no member named ‘tlb_size’
223 | gd->arch.tlb_size = PGTABLE_SIZE;
| ^
arch/arm/mach-stm32mp/cpu.c:224:10: error: ‘volatile struct arch_global_data’ has no member named ‘tlb_addr’
224 | gd->arch.tlb_addr = (unsigned long)&early_tlb;
| ^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Enable the clocks during bsec probe when they are present in device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The command "stm32prog serial <dev>" can directly use the device sequence
number of serial uclass as this sequence number is egual to alias when it
exist; this assumption simplify the code and avoid access to gd->fdt_blob
and the device tree parsing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When serial instance is not found in device tree, the console
should be enabled and the error should be indicated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add CONFIG_CMD_STM32PROG_SERIAL and CONFIG_CMD_STM32PROG_USB to
independently select the support of UART or USB communication for
STM32CubeProgrammer.
For serial boot over UART, user can deactivate CONFIG_CMD_STM32PROG_SERIAL
to use U-Boot console of binary loaded by UART (for board bring-up for
example).
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move CONFIG_CMD_STM32PROG in a specific Kconfig file for stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Overidde the weak function dram_bank_mmu_setup() to set the DDR
(preloc case) or the SYSRAM (in SPL case) executable before to enable
the MMU and configure DACR.
This weak function is called in dcache_enable/mmu_setup.
This patchs avoids a permission access issue when the DDR is marked
executable (by calling mmu_set_region_dcache_behaviour with
DCACHE_DEFAULT_OPTION) after MMU setup and domain access permission
activation with DACR in dcache_enable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Mark the top of ram, used for relocated U-Boot as a normal memory
(cacheable and executable) to avoid permission access issue when
U-Boot jumps to this relocated code.
When MMU is activated in pre-reloc stage; only the beginning of
DDR is marked executable.
This patch avoids access issue when DACR is correctly managed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Remove the test on data->dfu_seq, because dfu_seq=0 not only when
the DFU is not started (mask with 0xffff). This flush is mandatory
as the final treatment, common with USB, is done in DFU callback.
This patch avoids issue if the received length is a multiple of
the DFU packet.
For example if size of bootfs partition is egual to 0x4000000,
data->dfu_seq=0 at the end of the partition, the flush it not
requested and the phase is not increased in the callback.
U-Boot continue to request the bootfs in the next GetPhase command.
Fixes: 468f0508b5 ("stm32mp: stm32prog: add serial link support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Define LOG_CATEGORY, change pr_debug to dev_dbg and remove "bsec:"
header as it is managed by log macro (dev->name is displayed)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to log macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
spl_mmc_boot_partition is only defined when
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION is defined.
Signed-off-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Correct the ALIGN macro usage in mmu_set_region_dcache_behaviour
call: the address must use ALIGN_DOWN and size can use ALIGN macro.
With STM32_SYSRAM_BASE=0x2FFC0000 and MMU_SECTION_SIZE=0x100000 for
STM32MP15x the computed address was 30000000 instead of 2ff00000.
Fixes: 43fe9d2fda ("stm32mp1: mmu_set_region_dcache_behaviour")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
When partitions are not available on a device the command stm32prog raises
an error but a device can have no partition to check in init_device()
and the command need to continue to the next part_id.
This patch correct an issue for ram0 target, when block_dev and mtd
are NULL.
For example with the simple flashlayout file:
Opt Part Name Type Device Offset Binary
- 0x01 fsbl Binary none 0x0 tf-a-serialboot.stm32
- 0x03 ssbl Binary none 0x0 u-boot.stm32
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSytem ram0 0xC4000000 stm32mp157f-ev1.dtb
Fixes: ffc405e63b ("stm32mp: stm32prog: add upport of partial update")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Cosmetic update of gpio.h:
- remove enumerate: stm32_gpio_port, stm32_gpio_pin
because STM32_GPIO_XXX values are unused
- move STM32_GPIOS_PER_BANK in stm32_gpio.c
as its value is IP dependent and not arch dependent
No functional change as number of banks and number of gpio by banks
is managed by device tree since since DM migration and
commit 8f651ca60b ("pinctrl: stm32: Add get_pins_count() ops").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
In pre-reloc stage, U-Boot marks cacheable the DDR limited by
the new config CONFIG_DDR_CACHEABLE_SIZE.
This patch allows to avoid any speculative access to DDR protected by
firewall and used by OP-TEE; the "no-map" reserved memory
node in DT are assumed after this limit:
STM32_DDR_BASE + DDR_CACHEABLE_SIZE.
Without security, in basic boot, the value is equal to STM32_DDR_SIZE.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove the unnecessary inversion on the eth_env_set_enetaddr() result which
only make complex the code of setup_mac_address() and display an invalid
value in the associated pr_err.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Use IS_ENABLED to prevent ifdef in stm32prog command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use IS_ENABLED to prevent ifdef in bsec driver.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
This header file should not be included in other header files. Remove it
and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Refactor to allow any arch to create SPI-flash images
New button uclass
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8g33sRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreaeEgf/QhmJjd6lEE3ABncRa3texyqq7j9eu+9P
2JMCahrIzps83LLOkzNSGs1+m1hRuTcdnYNV8FxdmkAjDTYwV5RHOfwtpAr2nkH2
HBbJRA2qMPleqT8wcymouhaCIRTTCGfUkFgZ+OowwSlHnQ4d2oGU/59Z+AkbpfX0
3svA1Mlr5rUTZ3qTvdsepuZckuYOTGYZ5jgjbgr+G8F4iW4Ov+OkBxqDz9zFCveF
md5CHKP1SV+bq67Q9uqUEwatLzYpy1p24j1Qe4G08U1+XCi6r+95VEc7TWxggboj
eV/5d/sZbGESAtJiJ4TmqpGVcOLzBLI0FOunky0JNFwdcyRS/6KcCg==
=Xjil
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-28jul20' of git://git.denx.de/u-boot-dm
Use binman instead of one of the Rockchip build scripts
Refactor to allow any arch to create SPI-flash images
New button uclass
When binman is in use, most of the targets built by the Makefile are
inputs to binman. We then need a final rule to run binman to produce the
final outputs.
Rename the variable to indicate this, and add a new 'inputs' target.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Replace the function spl_board_prepare_for_boot_linux by the correct
name of the weak function spl_board_prepare_for_linux defined in spl.h.
This patch avoids warning with W=1 option:
u-boot/arch/arm/mach-stm32mp/spl.c:150:6:
warning: no previous prototype for ‘spl_board_prepare_for_boot_linux’
[-Wmissing-prototypes]
Fixes: dc7e5f190d ("arm: stm32mp: activate data cache on DDR in SPL")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Check result of find_mmc_device() before calling mmc_init().
This patch avoid a data abort when the command try to acces
to sd/mmc device deactivated in device tree.
Fixes: aff4c5dd82 ("stm32mp: stm32prog: add MMC device")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Since commit d877f8fd0f ("arm: provide a function for boards init
code to modify MMU virtual-physical map") the parameter of
mmu_set_region_dcache_behaviour need to be MMU_SECTION_SIZE
aligned.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As the dbgmcu_init use the function bsec_dbgswenable which is based
on the DM and DT, its call can't be done before the spl is initialized
(driver model, DT and malloc) in board_init_f::spl_early_init().
This function call is moved later in spl_board_init().
Fixes: bd3f60d29c ("arm: stm32mp: protect DBGMCU_IDC access with BSEC")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:
It's a **mistake** to use typedef for structures and pointers.
Besides, using typedef for structures is annoying when you try to make
headers self-contained.
Let's say you have the following function declaration in a header:
void foo(bd_t *bd);
This is not self-contained since bd_t is not defined.
To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>
#include <asm/u-boot.h>
void foo(bd_t *bd);
Then, the include direcective pulls in more bloat needlessly.
If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:
struct bd_info;
void foo(struct bd_info *bd);
Right, typedef'ing bd_t is a mistake.
I used coccinelle to generate this commit.
The semantic patch that makes this change is as follows:
<smpl>
@@
typedef bd_t;
@@
-bd_t
+struct bd_info
</smpl>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Add parentheses around CONFIG_IS_ENABLED() in the if statement, to
fix potential build failures.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate CMD_NVEDIT_INFO and use the new command "env info -d -p -q"
to automatically save the environment on first boot.
This patch allows to remove the env_default variable.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
As debugger must be totally closed on Sec closed chip,
the DBGMCU_IDC register is no more accessible (self
hosted debug is disabled with OTP).
This patch adds a function bsec_dbgswenable() to check
if the DBGMCU registers are available before to access them:
BSEC_DENABLE.DBGSWENABLE = self hosted debug status.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add "Device Name" in iproduct during DFU USB enumeration
to have this information in STM32CubeProgrammer trace
(this tools is compatible with @Name since v2.3)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function stmpic_init to early initialize the PMIC STPMIC1
- keep vdd on during the reset cycle (to avoid issue when backup battery
is absent)
- Check if debug is enabled to program PMIC according to the bit
This patch allows to remove the compilation of spl.c file from stm32mp1
board in dh_stm32mp1.
CONFIG_SPL_BOARD_INIT is removed as the new function is called earlier
in SPL, in the function board_early_init_f.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a weak functions to save the vddcore voltage value provided
in the OPP node when the clock tree is initialized.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add the bsec driver in SPL, as it is needed by SOC part number detection
to found the supported OPP.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Fix the sequence in stm32mp1 fdt.c that disables OP-TEE resources
defined in FDT when U-boot detects OP-TEE firmware is not present.
Before this change, helper function stm32_fdt_disable_optee()
set property status to "disabled" for the OP-TEE reserved memory
nodes but this has no impact since Linux kernel does not consider
the status property for reserved-memory subnodes. This change
make U-Boot to attempt to delete the node instead.
Fixes: 4a1b975dac ("board: stm32mp1: reserve memory for OP-TEE in device tree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some places use __ASSEMBLER__ instead which does not work since the
Makefile does not define it. Fix them.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not be using typedefs and these make it harder to use
forward declarations (to reduce header file inclusions). Drop the typedef.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Activate cache on DDR to improve the accesses to DDR used by SPL:
- CONFIG_SPL_BSS_START_ADDR
- CONFIG_SYS_SPL_MALLOC_START
Cache is configured only when DDR is fully initialized,
to avoid speculative access and issue in get_ram_size().
Data cache is deactivated at the end of SPL, to flush the data cache
and the TLB.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate the data cache in SPL and in U-Boot before relocation.
In arch_cpu_init(), the function early_enable_caches() sets the early
TLB, early_tlb[] located .init section, and set cacheable:
- for SPL, all the SYSRAM
- for U-Boot, all the DDR
After relocation, the function enable_caches() (called by board_r)
reconfigures the MMU with new TLB location (reserved in
board_f.c::reserve_mmu) and re-enable the data cache.
This patch allows to reduce the execution time, particularly
- for the device tree parsing in U-Boot pre-reloc stage
(dm_extended_scan_fd =>dm_scan_fdt)
- in I2C timing computation in SPL (stm32_i2c_choose_solution())
For example, the result on STM32MP157C-DK2 board is:
1,6s gain for trusted boot chain with TF-A
2,2s gain for basic boot chain with SPL
For information, as TLB is added in .data section, the binary size
increased and the SPL load time by ROM code increased (30ms on DK2).
But early malloc can't be used for TLB because arch_cpu_init()
is executed before the early poll initialization done in spl_common_init()
called by spl_early_init() So it too late for this use case.
And if I initialize the MMU and the cache after this function it is
too late, as dm_init_and_scan and fdt parsing is also called in
spl_common_init().
And .BSS can be used in board_init_f(): only stack and global can use
before BSS init done in board_init_r().
So .data is the better solution without hardcoded location but if you
have size issue for SPL you can deactivate cache for SPL only
(with CONFIG_SPL_SYS_DCACHE_OFF).
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Call hang when an error is detected for probe of any driver
needed for console or DDR init: clk, reset and pincontrol
NB: previous behavior with a return in board_init_f() was not correct;
DDR is not initialized and SPL execution can't continue
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This command is not more depending on fuse command, but have
direct access to BSEC misc driver, so the dependency with
can be removed CMD_FUSE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of RAM target in flashlayout to load kernel image
("system") and device tree ("filesystem") in DDR with DFU and
start these images.
The flashlayout.tsv is:
- 0x01 fsbl Binary none 0x00000000 tf-a.stm32
- 0x03 ssbl Binary none 0x00000000 u-boot.stm32
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 dtb.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Support an U-Boot script included in uimage instead of flashlayout file
(text file in tsv format).
This feature is used to execute this script directly when U-Boot is
loaded in DDR (for update without STM32CubeProgrammer for example).
A simple example with dfu-util only is:
$> echo "dfu 0" > script.cmd
$> mkimage -C none -A arm -T script -d script.cmd script.uimg
$> mkimage -T stm32image -a 0xC0000000 -e 0xC0000000 -d script.uimg \
script.stm32
$> dfu-util -d 0483:df11 -a 1 -D tf-a.stm32
$> dfu-util -d 0483:df11 -a 0 -D script.stm32
$> dfu-util -d 0483:df11 -a 0 -D u-boot.stm32
$> dfu-util -d 0483:df11 -a 0 -e
Then you can used dfu-utils to update your device
To increase speed, you can also switch to fastboot protocol with:
echo "fastboot 0" > script.cmd
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Enable the videoconsole during the stm32prog command execution
to have information without UART.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a support of UART, using the same protocol than MCU STM32.
See "AN5275: USB DFU/USART protocols used in STM32MP1 Series
bootloaders" for details.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a virtual partition to update the pmic non volatile memory.
(on ST board, STPMIC1).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a virtual partition to update the STM32MP15x OTP based
on SMC service provided by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for delete option 'D' in flashlayout for
full device or for partitions
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
For reliability of boot from NAND/SPI-NAND (with read-disturb issue)
the SSBL can be present several time, when it is indicated in the
flashlayout with "Binary(X)".
The received binary is copied X times by U-Boot on the target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Dynamically adapt the MTD partitions in NOR/NAND/SPI-NAND when stm32prog
command detects in the parsed flash layout files:
- a fsbl partition in NOR.
- a tee partition in NOR/NAND/SPI-NAND
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MTD device (DFU_MTD backend) for
NOR, NAND or SPI-NAND target.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of partial update, update only some partitions,
and check the coherence of the layout with the existing GPT
partitions (offset and size).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of eMMC device boot partition with
part_id = -1 for offset="boot1"
or = -2 for offset="boot2"
The stm32prog command configures the MMC DFU backend with "mmcpart"
and configure the eMMC (command "mmc bootbus" and "mmc partconf")
when the update is done.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support of MMC device (based on DFU_MMC backend)
for SD card and eMMC update.
Create a GPT partitioning on the device.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Build the list of device and of partition with
a tab separated value file with a stm32 header: the FlashLayout.tsv
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a specific command stm32prog for STM32MP soc family
witch allows to program the boot devices with the tool
STM32CubeProgrammer (http://www.st.com/STM32CubeProg).
This command uses the same UART STM32 protocol than MCU
STM32 with or USB with DFU protocol v1.1 (ithe MCU ST
extension are no supported).
The executed actions are based on a tab separated value file
with a stm32 header, the FlashLayout file
(https://wiki.st.com/stm32mpu/wiki/STM32CubeProgrammer_flashlayout).
This file is parsed by the U-Boot command to:
- initialize the devices
- create the partition table on each device
- initialize the DFU backend to access to not volatile memory
(NOR/NAND/SD/eMMC) or to virtual device (OTP/PMIC)
Up to STM32PROG_MAX_DEV (5) devices can be updated with a FlashLayout.
The communication between U-Boot and STM32CubeProgrammer is done with
the specific alternate configuration (see "AN5275: USB DFU/USART protocols
used in STM32MP1 Series bootloaders" for details).
The command stm32prog is executed when a boot from USB is detected
(selected with bootpins) and we can program the boot devices with
a simple command (on Windows or Linux):
PC $> STM32_Programmer_CLI -c port=usb1 -w flaslayout.tsv
1/ the ROM code loads TF-A in embedded RAM (DFU or uart)
2/ TF-A loads flashlayout file and U-Boot in DDR (DFU or uart)
3/ U-Boot executes the stm32prog command (DFU or uart)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_cpu_dev to get the DEV_ID present
in DBGMCU_IDC register.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Manage BOOT_FLASH_SPINAND, with boot_device="spi-nand"
and treat this value in bootcmd_stm32mp.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Save and use the FDT address provided by TF-A in r2 at boot time
(it is NT_FW_CONFIG = Non Trusted Firmware configuration file)
Address is saved in save_boot_params(), called by start.S
and the used DTB is gd->fdt_blob = board_fdt_blob_setup().
If dtb is not provided or invalid, U-Boot use as fallback
the builtin DTB.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Activate OP-TEE driver for trusted and optee defconfig.
This driver allows detection of TEE presence for boot from flash;
CONFIG_STM32MP1_OPTEE is also removed.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add reserve memory for OP-TEE in U-Boot and in kernel device tree:
- no more reduce the DDR size in "memory" node:
CONFIG_SYS_MEM_TOP_HIDE is no more used
- U-Boot device-tree defines the needed "reserved-memory" for OP-TEE
and U-Boot should not use this reserved memory: board_get_usable_ram_top
use lmb lib to found the first free region, the not reserved
memory, enough to relocate U-Boot: the needed size of U-Boot
is estimated with gd->mon_len + CONFIG_SYS_MALLOC_LEN.
- the optee node ("optee@...": firmware with compatible "linaro,optee-tz")
and the associated "reserved-memory" are deactivated in kernel device
tree when OP-TEE is not detected by U-Boot to prevent kernel issue
(memory is reserved but not used, optee driver probe failed).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add weak implementation of board_early_init_f() hook into the
STM32MP1 SPL. This can be used to read out e.g. configuration
straps before initializing the DRAM.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
This function is only relevant to the MMC driver so calling it
spl_boot_partition() might be confusing. Rename it to
spl_mmc_boot_partition() to make its purpose more clear (and bring
it in line with spl_mmc_boot_mode()).
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The function's name is misleading as one might think it is used
generally to select the boot-mode when in reality it is only used by the
MMC driver to find out in what way it should try reading U-Boot Proper
from a device (either using a filesystem, a raw sector/partition, or an
eMMC boot partition).
Rename it to spl_mmc_boot_mode() to make it more obvious what this
function is about.
Link: https://lists.denx.de/pipermail/u-boot/2020-April/405979.html
Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts the workaround introduced by the
commit 16fec9b0bc ("stm32mp1: remove the imply BOOTSTAGE")
As the bootstage alignment issue is now solved.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Define FMC2 base address, for use in board files, until there is an
actual FMC2 bus driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Need to increase the LPDDR2/LPDDR3 the voltage vdd2_ddr: buck2
form 1.2V to 1.25V for 32bits configuration.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
This path allows to set the cntfrq register of targeted cpu.
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
The STM32MP1 series is available in 3 different lines which are pin-to-pin
compatible:
- STM32MP157: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz,
3D GPU, DSI display interface and CAN FD
- STM32MP153: Dual Cortex-A7 cores, Cortex-M4 core @ 209 MHz
and CAN FD
- STM32MP151: Single Cortex-A7 core, Cortex-M4 core @ 209 MHz
Each line comes with a security option (cryptography & secure boot)
& a Cortex-A frequency option :
- A : Cortex-A7 @ 650 MHz
- C : Secure Boot + HW Crypto + Cortex-A7 @ 650 MHz
- D : Cortex-A7 @ 800 MHz
- F : Secure Boot + HW Crypto + Cortex-A7 @ 800 MHz
This patch adds the support of STM32MP15xD and STM32MP15xF in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Update the kernel device tree for STM32MP15x product lines according
the used soc and its part number, when CONFIG_OF_SYSTEM_SETUP is activated:
- STM32MP15XA hasn't Crypto (cryp1/2)
- STM32M151 and STM32M153 hasn't 3D GPU and DSI host
- STM32M151 hasn't CAN FD and has single A7
For example:
FDT: cpu 1 node remove for STM32MP151AAA Rev.B
FDT: can@4400e000 node disabled for STM32MP151AAA Rev.B
FDT: gpu@59000000 node disabled for STM32MP151AAA Rev.B
FDT: dsi@5a000000 node disabled for STM32MP151AAA Rev.B
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add a function get_soc_name to get a string with the full name
of the SOC "STM32MP15xxx Rev.x"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add the SMC code and operation for trace on errors.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove the test offs < 0 , as offs is unsigned.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
In function ‘stm32mp_bsec_read’:
arch/arm/mach-stm32mp/bsec.c:368:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
368 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
In function ‘stm32mp_bsec_write’:
arch/arm/mach-stm32mp/bsec.c:405:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
405 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Correct the dependency for STM32 ETZPC protection, linked to SOC
STM32MP identified by CONFIG_STM32MP15x and not linked to
CONFIG_TARGET_STM32MP1 (no more existing).
This patch fix an issue introduced by commit 846254888e ("stm32mp1:
split board and SOC support for STM32MP15x family").
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Add support for Rev.Z of STM32MP15x cpu.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Update the driver to use the latest binding from kernel v5.5-rc1:
no more use syscon or regmap to access to pwr register and
only one pwr_regulators node with the compatibility "st,stm32mp1,pwr-reg"
is available.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for DH Electronics DHCOM SoM and PDK2 rev. 400 carrier
board. This is an SoM with STM32MP15xx and an evaluation kit. The
baseboard provides Ethernet, UART, USB, CAN and optional display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
Split the board and SOC support for STM32MP15x family and
prepare the introduction of new boards with STM32MP15x.
This path define the 2 configurations:
- STM32MP15x: STM32MP15x soc support (new)
- TARGET_ST_STM32MP15x: STMicroelectronics board support (choice)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
