vexpress_ca9x4 is seemingly the only board except for qemu_arm which
is able to run U-Boot correctly, using the `-M vexpress-a9` option to
QEMU. Building for qemu_arm and running qemu-system-arm with the `-M
virt` argument has a number of downsides, most importantly that it
only supports virtio storage drivers. This significantly reduces its
usefulness in testing memory card and Flash solutions, especially when
the tested images are from a third party source.
So therefore we reintroduce the vexpress_ca9x4 board in this commit,
with the explicit goal of using it with QEMU.
A number of differences to note from the original:
* Since the board was apparently unmaintained, I have now set myself
as the maintainer.
* The board has been converted to use the driver model, which was the
reason it was removed in the first place.
* The vexpress_ca15_tc2 and vexpress_ca5x2 boards, which were removed
in the same commit, are not necessary for the QEMU use case, and
have been omitted.
* An `mmc0` alias was introduced in the dts file. The mmc is not
detected correctly without this, now that it's based on the device
tree instead of the board's init function.
* A couple of other nodes were removed because they were problematic
when trying to run the UEFI bootmgr. Once again, the primary use
case here is QEMU, and these nodes are not needed for that to work.
* Unnecessary board init code has been removed, thanks to driver model
and device tree.
* `CONFIG_OF_EMBED` has been enabled. I know this goes against
recommended practice, but there doesn't seem to be any other way to
pass the dtb to U-Boot in the QEMU scenario. Using the -dtb argument
does not work, I suppose because U-Boot doesn't use the same
mechanics as the kernel when it's booting.
* Load addresses have been changed to fit QEMU use case.
People wanting to get a more detailed, yet somewhat isolated, diff
between this and the original, can run this command:
git diff c6c26a05b89f25a06e7562f8c2071b60fd0c9eac~1 -- \
$( git diff-tree --diff-filter=A -r --name-only HEAD~1 HEAD)
(Make sure to either check out this commit first, or replace HEAD with
the commit ID of this commit)
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
On MediaTek boards we cannot override the SYS_BOARD / SYS_CONFIG_NAME
variables from defconfig.
This is because in board/mediatek/mtXXXX/Kconfig this value was override
by default due to the if CONFIG_TARGET_MTXXXX condition.
Merge all the Kconfigs to the mach-medatek/Kconfig.
This way:
- we only define SYS_{SOC,VENDOR} once
- all board definitions are in a single place, simplifying the build logic.
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmFKxpEcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBLaB/0XsIdkGAvcHLWW8yUg
27GiRznikNKwn9/qIj2ByraoUd4BvxdQV4gKHR1R9n0sgYh/8VMyLbmhRoCRKFwP
3mQ0MUyjaeU5sEWzasovJVpXhuUapEiV0jEg6t3Lgwd3mp2QK2Pk87zoleQfZNkb
VAVCnt1T+kb3y0W9oa3XZbuH2wam9T5pNWRGW70JbgzdwJNKLO1Qo7MfcUNiDxJu
Jf7uXtYwwILlN38G1KSk1ymMjfaotCqj7RzNaV3Ero57MVj3VzerKGb7H+XPOYf2
nYXyietYLJJkzvHzSDwIdCSVlOSQL8QqVB8GCmLiNQD4tG830RcvSJnYpRLylWQK
6F+Y
=Q/aS
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.01-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.01 cycle:
This feature set includes : the support for CPU driver for arm926
(sam9x60 device); changes required for OP-TEE boot for sama5d2_xplained
and sama5d27_som1_ek boards; QSPI boot configuration for sama5d2_icp;
starting to remove old Kconfig unused symbols from config_whitelist.txt
(work will take more time); also small fixes and updates in mach, DT,
configs, etc.
Add new config for storing environment from QSPI1.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
[eugen.hristev@microchip.com: cleanup and add MAINTAINERS entry]
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
In order to make it more flexible and allow modifying the base address
of DRAM without recompiling U-Boot, use memory node from device tree
with fdtdec functions.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
In order to make it more flexible and allow modifying the base address
of DRAM without recompiling U-Boot, use memory node from device tree
with fdtdec functions.
Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Header file version.h does not use anything from timestamp.h. Including of
timestamp.h has side effect which cause recompiling object file at every
make run because timestamp.h changes at every run.
So remove timestamp.h from version.h and include timestamp.h in files
which needs it.
This change reduce recompilation time of final U-Boot binary when U-Boot
source files were not changed as less source files needs to be recompiled.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add in lib/acpi/acpi_table.c and test/dm/acpi.c, rework a few others]
Signed-off-by: Tom Rini <trini@konsulko.com>
More C files do not use compile time timestamp macros and do not have to be
recompiled every time when SOURCE_DATE_EPOCH changes.
This patch moves version_string[] from version.h to version_string.h and
updates other C files which only needs version_string[] string to include
version_string.h instead of version.h. After applying this patch these
files are not recompiled every time when SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline.
Remove it.
Note that we have to add CONFIG_SPIFLASH to scripts/config_whitelist.txt
because it's not really migrated at this point.
Acked-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan <oleks@arcturusnetworks.com>
Acked-by: Oleksandr Zhadan and Michael Durrant <arcsupport@arcturusnetworks.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Handle CONFIG_SPIFLASH differently and delete Kconfig file]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds genimage [1] config files for generating SD card and spi-nor
images, which can be programmed to an SD card or SPI flash and boot
from there.
The same images will be used for U-Boot CI testing for this board.
[1] https://github.com/pengutronix/genimage
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Fix the dr_mode in the U-Boot device tree blob, by reading the mode field
from the USB Boot Configuration fields. The dr_mode will only be fixed when
booting from USB.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Change maintainer to me. Prafulla is no longer active in U-Boot community.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Move TI maintainership to Tom.
Updated with the following commands:
find ./ -name MAINTAINERS | xargs sed -i s/"Lokesh Vutla <lokeshvutla@ti.com>"/"Tom Rini <trini@konsulko.com>"/g
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
All of these configs exist. Stick to using CONFIG_[ST]PL_HASH, and drop all
references to CONFIG_[ST]PL_HASH_SUPPORT. This means we need for
CHAIN_OF_TRUST to select SPL_HASH now.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
[trini: Add TPL case, fix CHAIN_OF_TRUST, other tweaks]
Signed-off-by: Tom Rini <trini@konsulko.com>
As this is only useful when booting with ATAGs, which are now largely
disabled, remove this value for the remaining platforms. We have a few
places in the code that had been testing for MACH_TYPE as a sort of
internal logic. Update those to use different but still correct CONFIG
symbols.
Cc: Phil Sutter <phil@nwl.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support. A large number of platforms had enabled
support but never supported a kernel so old as to require it. Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years. This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user. When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts. In other cases, these
functions were simply unused, so drop them.
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
No iMX platforms have supported ATAG-based booting. They have however
re-used the CONFIG_SERIAL_TAG option as a way to enable support of
reading the OTP fuses and setting the serial# environment variable in
some cases. Change the warp7 support to use this symbol, use this for
updating the rest of the imx7 code, and update the imx8 conditionals.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP i.MX U-Boot Team <uboot-imx@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Invokes the common cache_init function to initialize ccache.
Signed-off-by: Zong Li <zong.li@sifive.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This converts the following to Kconfig:
CONFIG_POWER_I2C
CONFIG_POWER_LEGACY
They are handled at the same time due to a dependency between them.
Update the Makefile rule to use legacy power only in U-Boot proper.
Unfortunately a separate rule is needed in SPL to be able to build
legacy power. Add SPL related symbols for both, to allow for SPL-only
usage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: More SPL related cleanups, reword commit message]
Signed-off-by: Tom Rini <trini@konsulko.com>
This option is used in pre-driver model code and much of it has never
been converted to driver model.
We want to add a new option to enable power support, so we can use a
simple rule in the Makefile. Rename this one, which is really about
a particular implementation of power.
Also update the pmic.h header file so it either includes the legacy
API or the driver model one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
[trini: Fixup some incorrect renames]
Signed-off-by: Tom Rini <trini@konsulko.com>
Per a request from Andre Przywara and agreed with by Peter Hoyes, the
vexpress aemv8r support wasn't quite ready to be merged, but the
discussion had moved off list. We should keep the first patch in the
series for now, but revert the rest. This reverts the following
commits:
e0bd6f31ce doc: Add documentation for the Arm vexpress board configs
30e5a449e8 arm: Use armv8_switch_to_el1 env to switch to EL1
b53bbca63b vexpress64: Add BASER_FVP vexpress board variant
2f5b7b7490 armv8: Add ARMv8 MPU configuration logic
37a757e227 armv8: Ensure EL1&0 VMSA is enabled
Signed-off-by: Tom Rini <trini@konsulko.com>
The BASER_FVP board variant is implemented on top of the BASE_FVP board
config (which, in turn, is based on the Juno Versatile Express board
config). They all share a similar memory map - for BASER_FVP the map is
inverted from the BASE_FVP
(https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map)
* Create new TARGET_VEXPRESS64_BASER_FVP target, which uses the same
board config as BASE_FVP and JUNO
* Adapt vexpress_aemv8a.h header file to support BASER_FVP (and rename
to vexpress_aemv8.h)
* Enable config to switch to EL1 for the BASER_FVP
* Create vexpress_aemv8r defconfig
* Provide an MPU memory map for the BASER_FVP
For now, only single core boot is supported.
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[trini: Add MAINTAINERS, move BOOTCOMMAND to defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
Over the time, the "stemmy" U-Boot board was tested on several other
Samsung smartphones based on ST-Ericsson NovaThor Ux500. Convert the
documentation to reStructuredText at doc/board/ste/stemmy.rst and
make the device list complete. Also note that the board now boots
into USB Fastboot instead of just ending up at the U-Boot prompt.
The device table is mostly taken from the postmarketOS wiki article
(https://wiki.postmarketos.org/wiki/ST-Ericsson_NovaThor_U8500).
All the newly added devices were tested by Linus Walleij.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Disable MCU watchdog in board_late_init() instead of board_init(), so
that it is disabled after U-Boot enables SOC watchdog instead of before.
This way there is no window when the board is vulnerable.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
When booting over UART, sending U-Boot proper may take too much time and
MCU watchdog will reset the board before U-Boot proper is loaded.
Better disable MCU watchdog in SPL when booting over UART.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
We do not need to guard code in board_init() and board_late_init()
functions with the CONFIG_SPL_BUILD macro, since these functions are not
called in SPL.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
default n/no doesn't need to be specified. It is default option anyway.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SKIP_LOWLEVEL_INIT
CONFIG_SKIP_LOWLEVEL_INIT_ONLY
In order to do this, we need to introduce SPL and TPL variants of these
options so that we can clearly disable these options only in SPL in some
cases, and both instances in other cases.
Signed-off-by: Tom Rini <trini@konsulko.com>
Move the CONFIG_DDR_MB symbol to Kconfig. A later clean-up would be to
make dynamic memory size detection work based on how this is done on
other i.MX6 platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Troy Kisky <troy.kisky@boundarydevices.com>
- Provide a default Kconfig value of the default script
- Largely continue to define this via the board Kconfig file
- For the boards that select a script based on defconfig rather than
TARGET, keep this within the defconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
As this symbol can either be a fixed value or the function
get_board_ddr_clk, migration is tricky. Introduce a choice of DYNAMIC
or STATIC_DDR_CLK_FREQ. If DYNAMIC, we continue to use the board
defined get_board_ddr_clk function. If STATIC, set CONFIG_DDR_CLK_FREQ
to that value and now include/clock_legacy.h contains the function
prototype or defines get_board_ddr_clk() to that static value. Update
callers to test for DYNAMIC or STATIC.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since the gd->watchdog_dev member is going away, switch to using the
new wdt_stop_all() helper.
While here, clean up the preprocessor conditional: The ->watchdog_dev
member is actually guarded by CONFIG_WDT [disabling that in
x530_defconfig while keeping CONFIG_WATCHDOG breaks the build], and in
the new world order so is the existence of the wdt_stop_all()
function.
Actually, existence of wdt_stop_all() depends on CONFIG_${SPL_}WDT, so
really spell the condition using CONFIG_IS_ENABLED, and make it a C
rather than cpp if.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
These symbols are now either unused or were only used within the config
file to determine other logic, which could be done in a way that doesn't
further pollute the CONFIG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
While the Kconfig language seems to accept either form of whitespace, we
use a space throughout the project, except in these spots.
Signed-off-by: Tom Rini <trini@konsulko.com>
- As there are no boards that use different values for speed / slave on
different buses, use a single option.
- Switch to using the common SYS_I2C_SPEED / SYS_I2C_SLAVE options.
- Introduce _HAS_ options for additional buses as only the first one is
common to all users.
- Convert all remaining symbols to Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
The omap24xx I2C driver uses its own CONFIG namespace for common I2C
variables. Rather than convert more of them to Kconfig, rename these to
the common I2C ones and remove the entirely unused functionality. As
part of this, we make the am335x_shc platforms consistent with their
intended speed values.
Signed-off-by: Tom Rini <trini@konsulko.com>
