This patch is used to support DBD owner fuse changed to S400 only.
The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not
configured by S400 default setting. So these PDAC and MSC are invalid,
only DBD owner can access the corresponding resources.
We have to configure necessary PDAC and MSC for SPL before DDR
initialization.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To clean the upower codes by aligning codes format, check err_code
and add detail bits list for the memory magic number
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The swton indicates the logic switch, magic number 0xfff80 is hard
to understand, so use macro.
Some board design may not have MIPI_CSI voltage input connected per
data sheet. In that case, the upower power on API may dead loop mu to wait
response, however there is no response. So remove MIPI_CSI here, let
linux power domain driver to runtime enable the power domain.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
At present, in cgc1_pll3_init we don't set the pll3pfd div values,
just use the default 0. But on A1 part, ROM will set PLL3 pfd1div2
to 1 and pfd2div1 to 3.
This finally causes some clocks' rate decreased, for example USDHC.
So clear the PLL3DIV_PFD dividers to get correct rate.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Some space in SRAM0 will be protected by S400 to allow RX SecPriv mode
access only for boot purpose. Since SW will reuse the SRAM0 as SCMI
buffer and SPL container loading buffer, need to reconfigure MRC3.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Need to add DRAM access permission for S400, as S400 needs to access
it When SPL calls image authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To fit the DBD_EN fused part, we re-design the TRDC and XRDC assignment.
M33 will be the TRDC owner and needs to configure TRDC. A35 is the
XRDC owner, ATF will configure XRDC.
The handshake between U-boot and M33 image is used to sync TRDC and
XRDC configuration completion. Once the handshake is done, A35 and M33
can access the allowed resources in others domain.
The handshake is needed when M33 is booted or DBD_EN fused, because both
cases will enable the TRDC. If handshake is timeout, the boot will hang.
We use SIM GPR0 to pass the info from SPL to u-boot, because before the
handshake, u-boot can't access SEC SIM and FSB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
As M33 is responsible for TRDC configuration, the settings for A35
nonsecure world access and DMA0 access are moved to M33 image.
So remove the codes to release TRDC and configure it. Just keep
the configurations for reference.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
iMX8ULP A1 S400 ROM removes the setting for MRC4/5. So we have to set
them in SPL to allow access to DDR from A35 and APD PER masters
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since A1 ROM has fixed the ROM API eMMC issue, we should only use
the workaround for A0.1 part. Add a SOC revision check.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In both SPL and u-boot, after probing the S400 MU, get the chip revision,
lifecycle and UID from Sentinel.
Update get_cpu_rev to use the chip revision not hard coded it for A0
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since latest DTS has added multiple MU nodes, using compatible
string to find the device node is not proper. It finds the first
node with the compatible string matched even the node is disabled.
Signed-off-by: Ye Li <ye.li@nxp.com>
We did not add a prototype for spl_mmc_get_uboot_raw_sector to
include/spl.h before, so add and document one now. Correct the incorrect
prototype in board/advantech/imx8mp_rsb3720a1/imx8mp_rsb3720a1.c and
ensure that we have spl.h where we define a non-weak
spl_mmc_get_uboot_raw_sector as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
We don't need an empty function, we can just not enable the hook we
don't use.
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
Signed-off-by: Adam Ford <aford173@gmail.com>
Implement basic PSCI provider to let OS turn CPU cores off and on,
power off and restart the system and determine PSCI version. This
is sufficient to remove the need for the ATF BL31 blob altogether.
To make use of this functionality, active the following Kconfig options:
# CONFIG_PSCI_RESET is not set
CONFIG_ARMV8_MULTIENTRY=y
CONFIG_ARMV8_SET_SMPEN=y
CONFIG_ARMV8_SPL_EXCEPTION_VECTORS=y
CONFIG_ARMV8_EA_EL3_FIRST=y
CONFIG_ARMV8_PSCI=y
CONFIG_ARMV8_PSCI_CPUS_PER_CLUSTER=4
CONFIG_ARMV8_SECURE_BASE=0x970000
CONFIG_ARM_SMCCC=y
CONFIG_SYS_HAS_ARMV8_SECURE_BASE=y
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is the PSCI provider, it is necessary to correctly
program CSU and TZASC registers. Those are poorly documented, so
push in the correct values.
Signed-off-by: Marek Vasut <marex@denx.de>
In case U-Boot is a PSCI provider, map RAM explicitly as NS,
otherwise secondary cores crash with SError when attempting
to access RAM mapped as secure in EL2.
Signed-off-by: Marek Vasut <marex@denx.de>
The ROM pointers are in fact populated by the ATF BL31 blob, in case
U-Boot itself if the PSCI provider, there is no ATF BL31 blob, hence
ignore the ROM pointers.
Signed-off-by: Marek Vasut <marex@denx.de>
The custom lowlevel_init implementation is no longer necessary, since
it is responsible for routing and trapping SErrors in U-Boot in EL2,
which is implemented in common code since commit:
6c7691edd5 ("armv8: Always unmask SErrors")
Signed-off-by: Marek Vasut <marex@denx.de>
Add the board support for the i.MX8MM Cloos PHG board.
This board uses a imx8mm-tqma8mqml SoM from TQ-Group.
imx8mm-phg.dts and imx8mm-tqma8mqml.dtsi are taken
directly from Linux 6.2-rc3.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
When an I2C clock is enabled inside enable_i2c_clk() the clock rate is
configured as PLL_SYS_MAIN_120M_CLK / 2 = 60MHz.
Currently, the I2C clock is retrieved from I2C1_CLK_ROOT, which
may not be the one that was enabled.
As there is no clock driver for the imx7d, it is better to return 60MHz
for the I2C clock.
This provides a workaround for the imx7d-pico board, where I2C4 is
connected to the PMIC.
With this change, it is possible to convert the imx7d-pico board
to DM_I2C and DM_PMIC.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 56c2dbdaba ("imx: bootaux: cleanup code") introduces the
following LTO related warning:
"
arch/arm/mach-imx/imx_bootaux.c:24:31: warning: type of ‘hostmap’ does not match original declaration [-Wlto-type-mismatch]
24 | const __weak struct rproc_att hostmap[] = { };
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: array types have different bounds
1590 | const struct rproc_att hostmap[] = {
| ^
arch/arm/mach-imx/imx8m/soc.c:1590:24: note: ‘hostmap’ was previously declared here
../aarch64-linux-gnu/bin/ld: warning: u-boot has a LOAD segment with RWX permissions
"
This is because the weak empty array of structures "hostmap" is eventually
replaced by non-empty array of structures with different number of elements.
Fix this by avoiding weak variable size array, instead use a weak function
which returns single pointer to the array.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are no CONFIG_{TOOLS_,SPL_,TPL_,}IMX8M macros, nor is there one for
ARM64. Use plain IS_ENABLED(CONFIG_IMX8M) and IS_ENABLED(CONFIG_ARM64) to
avoid expanding the {TOOLS_,SPL_,TPL_,} part.
Fixes: 56c2dbdaba ("imx: bootaux: cleanup code")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.
This reinstates change from commit:
e26d0152d6 ("ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables")
which has been dropped in commit:
b0a284a7c9 ("imx: move get_boot_device to common file")
Fixes: b0a284a7c9 ("imx: move get_boot_device to common file")
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
This converts the following to Kconfig:
CONFIG_DM9000_BYTE_SWAPPED
CONFIG_DM9000_NO_SROM
CONFIG_DM9000_USE_16BIT
CONFIG_DM9000_DEBUG
CONFIG_MXC_GPT_HCLK
CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
Signed-off-by: Tom Rini <trini@konsulko.com>
We only need to enable DM_ETH if we have a networking driver. All
networking drivers depend on DM_ETH being enabled, and their selection
ensures DM_ETH will be enabled.
Signed-off-by: Tom Rini <trini@konsulko.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS_SDRAM
namespace do not easily transition to Kconfig. In many cases they likely
should come from the device tree instead. Move these out of CONFIG
namespace and in to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Switch to use binman to pack images
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add support for the MSC SM2S-IMX8PLUS SMARC Module. Tested in conjunction
with the MSC SM2-MB-EP1 Mini-ITX Carrier Board.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
The e10133 workaround was broken in two places:
- The code intended to temporarily mask all interrupts in GPC_IMRx_CORE0.
While the old register values were saved, the actual masking was
missing.
- imx_udelay() expects the system counter to run at its base frequency,
but the system counter is switched to a lower frequency earlier in
psci_system_suspend(), leading to a much longer delay than intended.
Replace the call with an equivalent loop (linux-imx 5.15 does the same)
This fixes the SoC hanging forever when there was already a wakeup IRQ
pending while suspending.
Fixes: 57b620255e ("imx: mx7: add system suspend/resume support")
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
This enables armv8 crypto extension usage for SHA1/SHA256.
Which speed up sha1/sha256 operations, about 10x faster with
a imx8mm evk for a 20MiB kernel hash verification (12ms vs 165ms).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
i.Core MX8M Plus is an EDIMM SoM based on NXP i.MX8M Plus from Engicam.
i.Core MX8M Plus needs to mount on top of this Evaluation board for
creating complete i.Core MX8M Plus EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
This is not needed and we should avoid typedefs. Use the struct instead
and rename it to indicate that it really is a legacy struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.
So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.
Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix spurious ampersand in address print e.g.
Find img info 0x&480331a0, size 855
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>"
This commit adds board support for i.MXRT1170-EVK from NXP. This board
is an evaluation kit provided by NXP for i.MXRT117x processor family.
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
This board is missing migration to CONFIG_DM, which had a deadline of
v2020.01, which is now more than 2 years passed due. Remove it.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
SPL_GPIO_SUPPORT is named SPL_GPIO since commit 83061dbd1c ("Rename
GPIO_SUPPORT to GPIO"), SPL_MMC_SUPPORT is named SPL_MMC since commit
103c5f1806 ("mmc: Rename MMC_SUPPORT to MMC"), SPL_SERIAL_SUPPORT is
named SPL_SERIAL since commit 2a73606668 ("serial: Rename
SERIAL_SUPPORT to SERIAL") so let's select the correct Kconfig options.
Fixes: 8b71576f38 ("mx7ulp_com: add support for SPL")
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Set ARM clock to OD frequency 1.7Ghz, since we have set PMIC VDD_SOC
to Overdrive voltage 0.9V
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement the DDR driver clock interfaces for set DDR rate and
bypass DDR PLL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add bootaux command to support on-demand booting M33 from u-boot.
It kicks M33 via ATF by "bootaux 0x201e0000 0"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support on-demand booting M33 image from A core. SPL needs
to follow M33 kick up sequence to release M33 firstly,
then set M33 CPUWAIT signal. ATF will clear CPUWAIT to kick
M33 to run.
The prepare function also works around the M33 TCM ECC issue by
clean the TCM. Also enable sentinel handshake and WDOG1 clock
for M33 stop and reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add power init of MEDIAMIX, MLMIX and DDRMIX. And clear isolation
of MIPI DSI/CSI, USBPHY after the power up.
SPL should call the power init in its boot sequence before accessing
above three MIX and USB.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the get chip revision methond to use S400 API, also record
other information like lifecycle and UID to global data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add TRDC driver to iMX9. The TRDC init splits to two phases:
1. Early init phase will release TRDC from Sentinel and open write
permission to the memory where SPL image runs. Sentinel will set
the memory to RX only after ROM authentication for the OEM
closed part.
2. Init phase will configure TRDC to allow non-secure master to
access DDR. So the peripherals can work in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since iMX9 uses S401 which shares the API with iMX8ULP. So move S400
MU driver and API to a common place and selected by CONFIG_IMX_SENTINEL
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX9 shares same ROM API with i.MX8ULP, so make the i.MX8ULP the function
prototype common and usable by i.MX9.
Also include mmc env functions that use ROM API.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add timer_init to update ARM arch timer with correct frequency
from system counter and enable system counter.
Signed-off-by: Jian Li <jian.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add clock API to support CCM root clock and LPCG setting
Set the CCM AUTHEN register to allow non-secure world to set
root clock and lpcg.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
i.MX8MN/P/ULP supports ROM API, they have almost same get_boot_device
implementation, so move to a common file. And when support i.MX9,
no need to include the other function copy.
Since sys_proto.h is included in imx_romapi.c, there will be build
warning for i.MX8M because wdog_regs not defined, so include imx-regs.h
in i.MX8M sys_proro.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
For SoCs support ROM API, CONFIG_SPL_BOOTROM_SUPPORT is needed,
so use this macro to guard the code to avoid extend the list.
And drop the guard with structure definition, there is no need.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move the default mapping of spl_boot_device to weak function of
spl_board_boot_device. So that every board of iMX7/8/8M can overwrite
this function to implement specific mapping.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The SPL SDP is configured as BOOT_DEVICE_BOARD, so when booting from
USB, change its type to BOOT_DEVICE_BOARD, so we can use SDP.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
With supporting timer_get_boot_us, we can profile boot up time with below
configs and function bootstage_mark_name().
CONFIG_BOOTSTAGE=y
CONFIG_BOOTSTAGE_REPORT=y
CONFIG_CMD_BOOTSTAGE=y
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Simplify the use of the ROM API by using the wrappers that take care
of saving/restoring gd and computing the xor value. This makes the
generated code smaller and the C code easier to read.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The ROM API is thoroughly undocumented, but apparently passing the xor
of the real arguments as an extra argument is required [1]. Also, we
need to do the "save gd/restore gd" dance. These are both error-prone,
and lead to a lot of code duplication.
Since both imx8m[np] and imx8ulp SOCs have this, add a separate
translation unit which is included precisely when the new
CONFIG_IMX8_ROMAPI symbol is set, which provide convenience wrappers
that take care of computing the xor value as well as doing the gd
dance, and that thus have a more intuitive API. Subsequent patches
will make use of these to reduce boilerplate.
[1] One wonders, for example, if the check is only applied to the
lower 32 bits, or if we're implicitly relying on all 64-bit pointer
values we're passing effectively have 0 in the upper 32 bits.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In order not to repeat the IMX8MN || IMX8MP || IMX8ULP logic in
multiple places where we need to know if the SOC exposes the ROM API,
add a "def_bool y" Kconfig symbol.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Introduce board/siemens/common/Kconfig and have it hold FACTORYSET to
start with. Use select for this on the boards that need it.
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Samuel Egli <samuel.egli@siemens.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add CAAM support, which is required when enabling HAB secure boot.
Select CONFIG_SPL_DRIVERS_MISC so that CONFIG_IMX_HAB could
build successfully, if selected.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Tested-by: Frieder Schrempf <frieder.schrempf@kontron.de>
