The current mechanism is unnecessarily complex. Simplify the whole mechanism
such that the entire fitImage is signed, IVT is placed at the end, followed
by CSF, and this entire bundle is also authenticated. This makes the signing
scripting far simpler.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the DEBUG is enabled, these three lines warn about cast of
pointer to integer of different size, add the missing casts to fix
the warnings.
Signed-off-by: Marek Vasut <marex@denx.de>
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HW_CTRL_SEL should be cleared when configuring PLL to avoid
potential glitch
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support print reset cause. Since SRSR is not accessible from non-secure
world, so first save it to grp0, then read it in non-secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The MAC addresses are hard coded for bring up. Change it to support
reading from fuse.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
OPTEE memory region is set secure access only in ATF with configuration
to TRDC, and need to remove it from U-Boot, otherwise U-Boot and Kernel
may crash when accessing the memory
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Stop polluting the architecture directory with driver specific code,
move it into driver where it should be. Split the code slightly so
the MX8MM/MX8MN fuse readout and programming and MX8MP fuse readout
and programming are in their separate functions, and called in case
of matching SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
It seems like the ROM log events for the iMX8M are not fully covered by
AN12853 i.MX ROMs Log Events, Rev. 0, May 2020. On iMX8M the ROM event
ID 0x82 seems to use parameter0 which stops the parsing because the end
of list is detected too early.
This patch adds ROM event ID 0x82 and skips the next word if ID 0x82 is
parsed.
Fixes: a5ee05cf71 ("ARM: imx: Pick correct eMMC boot partition from ROM log")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The original function was only called once, before relocation. The new
one is called again after relocation. This was not the intent of the
original call. Fix this by renaming and updating the calling logic.
With this, chromebook_link64 makes it through SPL.
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It doesn't seem appropriate for arch/SOC to use a board-level
functionality (CONFIG_OF_BOARD_FIXUP), because this prevents boards
that need to do FDT fixup from using that feature.
Also, this code is completely dead and useless (from comments by
Rasmus Villemoes on the mailing list):
- No in-tree imx8m-based board seems to set CONFIG_OF_BOARD_FIXUP
- The nodes which that function wants to disable don't even exist in
the U-Boot copy of imx8mp.dtsi.
This code was introduced in commit 35bb60787b. It seems to be some
random import of code from downstream NXP U-Boot, with a commit
message that makes no sense in upstream context.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 787f04bb6a ("imx: add USB2_BOOT type") broke get_boot_device()
for IMX8 which affects booting from SDP due to boot_instance being
non-zero.
Fix this by only using boot_instance for imx8ulp and imx9.
Fixes: 787f04bb6a ("imx: add USB2_BOOT type")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add debug messages to print the real pixel clock rate, which may not be
the requested one.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Add the get_lcd_clk() function to get the LCD pixel clock rate.
The patch has been tested on imx6ul platform.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
During some tests to check the pixel clock rate in the transition from
U-Boot to the Linux kernel, I noticed that with the same configuration
of the registers the debug messages reported different rates.
The same Linux kernel calculations are now used to get the PLL video
rate.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Avoid a buffer overflow if assigned-clock-rates has less than two elements.
Fixes: 98bcdf1635 ("imx8mn: Add low drive mode support for DDR4/LPDDR4 EVK")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The MNT Reform 2 is a modular DIY laptop. In its initial version it
is based on the BoundaryDevices i.MX8MQ SoM. Some parts have been
lifted from BoundaryDevices official U-Boot downstream project.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Beacon Embedded has an i.MX8M Plus development kit which consists
of a SOM + baseboard. The SOM includes Bluetooth, WiFi, QSPI, eMMC,
and one Ethernet PHY. The baseboard includes audio, HDMI, USB-C Dual
Role port, USB Hub with five ports, a PCIe slot, and a second Ethernet
PHY. The device trees are already queued for inclusion in Linux 6.3.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support for Data Modul i.MX8M Plus eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR, USB.
Signed-off-by: Marek Vasut <marex@denx.de>
U-Boot can be booted from NAND without SPL by prepending the DCD header to
the actual U-Boot binary. However this requires prepending 1024 bytes to
u-boot.imx (DCD + u-boot.bin).
There is already a similar target to build spl/u-boot-nand-spl.imx, add the
same option for no-SPL boot.
Tested on i.MX6ULL.
The resulting layout of u-boot-nand.imx is:
- Offset 0x0000 (0 KiB): padding
- Offset 0x0400 (1 KiB): DCD header
- Offset 0x1000 (4 KiB): u-boot.bin
Signed-off-by: Luca Ceresoli <luca.ceresoli@bootlin.com>
The FEC interface mode is now configured in common board_interface_eth_init()
and called by FEC MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
In order for i2c_num==4 and 5 to stay invalid for non-imx8mp SOCs, the
i2c_ccgr[] array must be sized by the number of initializers present,
not with a hard-coded 6 which would implicitly initialize the last two
elements with zeroes.
Also, the bounds check is off-by-one.
Fixes: c92c3a4453 "ARM: imx: imx8mp: Enable support for i2c5 and i2c6 on i.MX8MP"
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Implement common board_interface_eth_init() and call it from the FEC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Mini/Nano/Plus FEC and supersedes the current board-side
configuration of the same IOMUX GPR[1] duplicated in the board files.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common board_interface_eth_init() and call it from the DWMAC
driver to configure IOMUXC GPR[1] register according to the PHY mode
obtained from DT. This supports all three interface modes supported by
the i.MX8M Plus DWMAC and supersedes current board-side configuration
of the same IOMUX GPR[1] duplicated in the board files.
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
The DWMAC clock in i.MX8M Plus were so far configured via ad-hoc
architecture code. Replace that with DM clock instead. This way,
the driver claims all its required clock, enables and disables
them, and even gets the CSR clock rate and sets the TX clock rate,
without any need of architecture specific register fiddling. Drop
the architecture specific code while at it too.
The adjustment here is modeled after STM32MP15xx clock handling
in this driver.
Signed-off-by: Marek Vasut <marex@denx.de>
The OEM Secure World Closed is not a valid lifecycle on iMX8ULP/iMX9.
So remove it from lifecycle print.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Before moving the lifecycle to OEM closed, confirm the lifecycle is
OEM open, otherwise cancel to move forward the lifecycle.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Remove legacy command definitions, change to use new ELE_xxx command
request.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Use common file ele_ahab.c for i.MX9 and iMX8ULP AHAB support, since
both of them use same sentinel ELE APIs
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
