Implement sam9x60 USB clock driver. This clock has
three parents: PLLA, UPLL and MAINXTAL. The driver is
aware of the three possible parents with the help of the
two mux tables provied to the driver during the registration
of the clock.
Signed-off-by: Sergiu Moga <sergiu.moga@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Do not cache the single CPG MODE register bit 12, instead cache the
entire register value, and only pick the matching bit from the cached
value when core clock of type MDSEL or PE are used. Both MDSEL and PE
clock type currently define .offset field as 12 on Gen3, which means
this code will use bit 12 on Gen3 again, however there are additional
clock on Gen4 which use different bits, and having this flexibility
in place now will be useful when adding Gen4.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The CLK_RCAR_GEN3 registers two subdrivers, clk_gen3 and rst_gen3.
The former depends on the clock framework, which is always enabled
in this context of clock framework driver, while the later depends
on reset framework which may not always be enabled.
Ensure the reset framework is also always enabled to prevent inobvious
early boot time bind failure of the CPG driver, which leads to system
showing no activity and is difficult to debug.
Note that one possible approach to debug this is to use CONFIG_DEBUG_UART
and add debug printascii()s into the drivers/clk/renesas/clk-rcar-gen3.c .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
There are missing Kconfig dependencies in the code which is using
firmware interface.
The commit 71efd45a5f ("arm64: zynqmp: Change firmware dependency")
add option to also disable ZYNQMP_FIRMWARE. But not all Kconfig
dependencies were properly described and also sdhci and gem drivers
didn't protect the code properly.
So, add the missing ZYNQMP_FIRMWARE dependencies.
Signed-off-by: Algapally Santosh Sagar <santoshsagar.algapally@amd.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230201095553.11219-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
According to the PLL vendor, we should keep the PLL power on, so we
shouldn't toggle the power-down bit during PLL initialization.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
SDHCI driver may attempt to set 26MHz clock, but clk_rk3568
will return error in this case. Apparently, SDHCI silently ignores the
error and as a result eMMC initialization fails.
Add 25 MHz and 26 MHz clk rates for sdmmc and emmc on rk3568 to fix that.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add RK3588 pll set and get rate clock support.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock driver support for Rockchip RK3588 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The USB SS-PHY needs its own clock, however, some clocks don't have
clock gates. Define missing clock entries for the PHY as reference
clock.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This allows devm_clock_get(dev, NULL) to work and get the first clock,
which is common in code ported from Linux.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Link: https://lore.kernel.org/r/20230122000252.53642-1-samuel@sholland.org
[backport from linux commit bedcf9d1dcf88ed38731f0ac9620e5a421e1e9d6]
Unlike audio_pll1 and audio_pll2, there is no video_pll2. Further, the
name used in the RM is video_pll. So, let's rename "video_pll1" to
"video_pll" to be consistent with the RM and avoid misunderstandings.
No functional changes intended.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20221219113127.528282-3-dario.binacchi@amarulasolutions.com
[backport from linux commit a429c60baefd95ab43a2ce7f25d5b2d7a2e431df]
The IMX8MN platform does not have any video processing unit (VPU), and
indeed in the reference manual (document IMX8MNRM Rev 2, 07/2022) there
is no occurrence of its pll. From an analysis of the code and the RM
itself, I think vpu pll is used instead of m7 alternate pll, probably
for copy and paste of code taken from modules of similar architectures.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Acked-by: Sean Anderson <seanga2@gmail.com>
Link: https://lore.kernel.org/r/20221219113127.528282-2-dario.binacchi@amarulasolutions.com
This converts 12 usages of this option to the non-SPL form, since there is
no SPL_SANDBOX_CLK_CCF defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 7 usages of this option to the non-SPL form, since there is
no SPL_CMD_CLK defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
R-Car V3U has a CPG different enough to not be a generic Gen3 CPG but
similar enough to reuse code. Introduce a new CPG library, factor out
the SD clock and RPC clock handling and hook them to the generic Gen3
CPG driver so we have an equal state.
Based on Linux commit [1] and [2] by Wolfram Sang
[1] 8bb67d87346a ("clk: renesas: rcar-gen3: Factor out CPG library")
[2] 6f21d145b90f ("clk: renesas: cpg-lib: Move RPC clock registration to
the library")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek: - Add rcar_clk_* prefix to all functions
- Rebase on changes to
clk: renesas: Introduce and use rcar_clk_get_rate64_div_table function
- Use u32_encode_bits/GENMASK bitfield ops
On R-Car V3M (AKA R8A77970), the SD0CKCR is laid out differently than on
the other R-Car gen3 SoCs. Hence, new clock types are introduced
respectively.
Based on Linux commit 381081ffc294 ("clk: renesas: r8a77970: Add SD0H/SD0
clocks for SDHI") by Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek: - Fix missing ~ in GENMASK(a, b), use clrsetbits_le32 instead
- Do not modify r8a77970-cpg-mssr.c much, drop enum r8a77970_clk_types
which is now part of common clock types in rcar-gen3-cpg.h instead
The old SD handling code was huge and could not handle all the details
which showed up on R-Car Gen3 SoCs meanwhile. It is time to switch to
another design. Have SDnH a separate clock, use the existing divider
clocks and move the errata handling from the clock driver to the SDHI
driver where it belongs.
Based on Linux series by Wolfram Sang, commit bb6d3fa98a41 ("clk:
renesas: rcar-gen3: Switch to new SD clock handling") and commit
e5f7e81ee430a ("mmc: renesas_sdhi: Parse DT for SDnH")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek: - Add rcar_clk_* prefix to all functions
- Fix missing ~ in GENMASK(a, b), use clrsetbits_le32 instead
- Use DIV_ROUND_CLOSEST, else if parent clock = 199999992 and
rate = 200000000, the divider would be 0 and table lookup
would fail.
- Turn rcar_clk_get_table_val into signed integer, so it can
return 0 as a valid value and negative values as errors.
- Make the code operate on correct clock and add comment
which explains the reasoning behind it.
- Rebase on changes to
clk: renesas: Introduce and use rcar_clk_get_rate64_div_table function
The RPCSRC clock divider on R-Car D3 is very similar to the one on R-Car
E3, but uses a different pre-divider for the PLL0 parent. Add a new
macro to describe it, reusing the existing clock type for R-Car E3.
As both E3/D3 RPCSRC clock divider are different from the rest of R-Car
Gen3, keep the original implementation from Linux.
Based on Linux commit 40745482eec8 ("clk: renesas: r8a774c0: Add RPC
clocks") by Lad Prabhakar and 9d18f81b3535 ("clk: renesas: r8a77995: Add
RPC clocks") by Geert Uytterhoeven.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Add D3 tweaks
Introduce new helper function to handle clock type that uses
clk_div_table struct. Based vaguely on Linux code. Make use
of clk_div_table in RPC clocks handling.
The E3/D3 RPCSRC need to be handled differently and will be addressed in
subsequence patch.
Based on Linux commit db4a0073cc82 ("clk: renesas: rcar-gen3: Add RPC
clocks") by Sergei Shtylyov.
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Marek: - Squash patches to avoid adding unused code:
clk: renesas: Make use of clk_div_table in RPC clocks handling
clk: renesas: Introduce rcar_clk_get_rate64_div_table function
- Move the new code to the beginning of clk-rcar-gen3 to avoid
tables mixed with code
- Use rcar_ prefix for get_table_div function
- Get rid of custom macros, use GENMASK. Use custom field_get
implementation as the generic FIELD_GET does not support
constant mask and u32_get_bits requires higher optimization level
- Pass in the register bit mask instead of width/shift combination
- Turn rcar_clk_get_rate64_div_table into s64, as it can return -EINVAL
Replace custom local structure with matching one from clk-provider.h .
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Drop 'core' parameter from gen3_clk_get_rate64_pll_mul_reg() function
as it is only used in debug print. No functional change except for the
debug print, which is disabled by default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Since commit f7b4e4c094 ("clk: renesas: Synchronize R-Car Gen3 tables
with Linux 5.12"), the custom macros for RPC clocks were dropped.
Use pre-defined offset for RPC clocks, same as what Linux does, instead
of retrieving it from the macros
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add trivial reset driver extension to the CPG clock driver. The change
turns current CPG UCLASS_CLK driver instance into an UCLASS_NOP proxy
driver, which in turn binds both generic rcar3_clk UCLASS_CLK clock
driver as well as generic rcar_rst UCLASS_RESET reset driver to the
CPG DT node. This way, any other drivers which use the 'reset' DT
property can now obtain valid reset handle backed by a reset driver.
The clock tables have been updated to represent the CPG driver and only
implement the generic CPG proxy driver bind call, which binds the clock
and reset drivers.
The DM_RESET is now enabled for all R-Car Gen3 platforms.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add support for the R-Car M3-W+ (R8A77961) SoC.
R-Car M3-W+ is very similar to R-Car M3-W (R8A77960), which allows for
both SoCs to share a driver.
Based on Linux commit 2ba738d56db4 ("clk: renesas: r8a7796: Add R8A77961
CPG/MSSR support")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Rename CONFIG_CLK_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_CLK_R8A77960, to avoid confusion with R-Car M3-W+ (R8A77961),
which will use CONFIG_CLK_R8A77961.
Based on Linux commit 92d1ebae9abf ("clk: renesas: Rename CLK_R8A7796
to CLK_R8A77960")
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774E1 RZ/G2H clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774C0 RZ/G2E clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774B1 RZ/G2N clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774A1 RZ/G2M clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779A0 V3U clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Rename CLK_TYPE_R8A779A0_ to CLK_TYPE_GEN4_ to match the new
clock tables. Add CLK_TYPE_GEN4_SD, CLK_TYPE_GEN4_RPC and
CLK_TYPE_GEN4_RPCD2 macros and handling into Gen3 CPG core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Currently, SDnH is handled together with SDn. This caused lots of
problems, so we want SDnH as a separate clock. Introduce a dummy SDnH
type here which creates a fixed-factor clock with factor 1. That allows
us to convert the per-SoC CPG drivers while keeping the old behaviour
for now. A later patch then will add the proper functionality.
Based on Linux series by Wolfram Sang:
commit a31cf51bf6b4b ("clk: renesas: rcar-gen3: Add dummy SDnH clock"),
commit 1abd04480866c ("clk: renesas: rcar-gen3: Add SDnH clock"),
commit 63494b6f98f26 ("clk: renesas: r8a779a0: Add SDnH clock to V3U")
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org> # Switch to gen3_clk_get_rate64
Synchronize R-Car device trees with Linux 6.1.7,
commit 21e996306a6afaae88295858de0ffb8955173a15 .
The following script has been used for the synchronization:
$ for i in $(cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) ; do
if [ -e /linux-2.6/arch/arm64/boot/dts/renesas/$i ] ; then
cp /linux-2.6/arch/arm64/boot/dts/renesas/$i arch/arm/dts/ ;
elif [ -e /linux-2.6/arch/arm/boot/dts/$i ] ; then
cp /linux-2.6/arch/arm/boot/dts/$i arch/arm/dts/
else
echo "NOT FOUND: $i"
fi
done
$ git add $( ( cd arch/arm/dts/ ; ls -1 r8a* | grep -v 'u-boot.dts' ; sed -n '/#include/ s@.*"\(.*\)"@\1@p' $(ls -1 r8a* | grep -v 'u-boot.dts')) | tr " " "\n" | sed 's@^@arch/arm/dts/@g' )
Move the include/dt-bindings/{clk,clock}/versaclock.h header used by
the renesas boards to match Linux 6.1.y as well.
Keep arch/arm/dts/r8a774c0-u-boot.dtsi sdhi3 node as it is now used
by the arch/arm/dts/r8a774c0-cat874.dts board.
Pick s@spi-flash@flash@ change in arch/arm/dts/r8a779a0-falcon-u-boot.dts
from "ARM: dts: Synchronize R-Car V3U DTs with Linux 5.18.3" .
Adjust R8A77990 Ebisu CONFIG_SYS_MMC_ENV_DEV from 2 to 0 to reflect
the card enumeration in ebisu.dtsi /aliases DT node .
Adjust R8A7795 and R8A7796 ULCB CONFIG_SYS_MMC_ENV_DEV from 1 to 0 to
reflect the card enumeration in ulcb.dtsi /aliases DT node .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com> # r8a779a0-falcon-u-boot.dts
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com> # r8a779a0-falcon-u-boot.dts
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCY9PmzwAKCRDKSWXLKUoM
IYWxAJwNgiXtFT17pBy+1M0JvSWgyvWF3QCfTQG2Krnw0+d65PF5A7UFTDL7SZM=
=cMrc
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.04-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx chnages for v2023.04-rc1
makefile:
- Add multi_dtb_fit dependency
clk:
- Handle error cases
microblaze:
- Disable falcon mode and cleanup code around
xilinx:
- Enable regular expression matching in board_fit_config_name_match()
- Fix FRU handling for 0xC1 format
- Fix Xilinx legacy format eeprom parsing
zynqmp:
- Some DT updates/cleanups
- Fix IDcode for xck24
- Remove empty mini config files
- Add support for k24
versal:
- Remove empty mini config files
versal_net:
- Setup timer when runs in EL3
- Build u-boot.elf for mini configurations
zynq-gem:
- Add support for new compatible strings
- Remove support for Avnet Ultrazedev SOM
- Handle SGMII with PCS phy
spi:
- Add support for gigadevice parts
misc:
- Remove CONFIG_TARGET_VENUS ifdef
- Add missing headers to remove sparse warnings
Add clock/reset definitions for display-related peripherals, including
the display engine, TCONs, and DSI and HDMI encoders, so those drivers
can be converted to DM clock consumers instead of directly manipulating
the CCU registers.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Add clock driver support for Rockchip RV1126 SoC.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the PCLK_WDT_NS clock to px30_clk_enable so that the watchdog driver
can probe since it wants to enable this clock.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In order to update the DT for rk3128
sync the clock dt-binding header.
This is the state as of v6.0 in Linux.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Introduce the auto-generated clock tree and power domain data needed to
attach the am62a into the power-domain and clock frameworks of uboot
Signed-off-by: Bryan Brattlof <bb@ti.com>
