Add a driver for GPIO backlights.
It understands the standard device tree binding.
It can be used with simple-panel when PWM is not necessary.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add a config to select individually the driver for PWM backlights.
Manage "depends on" to be backyard compatible.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
MX6Q/QP IPU operates at 264MHz and MX6DL IPU at 198MHz.
When running a SPL target, which supports multiple MX6 variants we cannot
properly setup the IPU clock frequency via CONFIG_IPUV3_CLK option as
such decision is done in build-time currently.
Remove the CONFIG_IPUV3_CLK option and let the IPU clock frequency be
configured in run-time on mx6.
Reported-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
[agust: fixed #endif in cgtqmx6eval.h]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Boards can skip display interface init using board_video_skip().
If display interface was not initialized (e.g. no ipuv3 framebuffer
registered or IPU clock disabled), booting Linux stops due to the
crash in IPU shutdown function, when accessing IPU registers.
Check IPU clock and skip shutdown if clock is not enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This reverts commit 1d20170467, reversing
changes made to 6aee2ab68c.
The mxc_ipuv3_fb.c changes introduce build failures on some targets.
Signed-off-by: Tom Rini <trini@konsulko.com>
Boards can skip display interface init using board_video_skip().
If display interface was not initialized (e.g. no ipuv3 framebuffer
registered or IPU clock disabled), booting Linux stops due to the
crash in IPU shutdown function, when accessing IPU registers.
Check IPU clock and skip shutdown if clock is not enabled.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add rk3288 soc specific driver for mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add Makefile item for soc specific driver for rk3399 mipi dsi.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To compatible with different rockchip soc, we split the mipi dirver into
common and soc specific parts, and all the soc share the common
functions from common driver part.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[agust: fix build breakage and warnings]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Update these drives to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Add some debugging to show when the backlight is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Update this driver to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
We should sync the display (e.g. flush cache) when backspace is pressed
to ensure that the character is erased correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Calculate the time taken to set up the LCD.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Some address relevant varibable is defined originally as u64. To
compatible with arm32, this patch change them to uintptr_t type.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
On reset the standby bit is clear, but if U-Boot is chain-loaded from
another boot loader it may be set. Clear it before starting up video so
that it works correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby':
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add remove() methods for EDP and VOP so that U-Boot can shut down the
video on exit. This avoids leaving DMA running while booting Linux which
can cause problems if Linux uses the frame buffer for something else.
It also makes it clear what is needed to shut down video.
While we are here, make rkvop_enable() static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Squashed in 'rockchip: video: fix taking the VOP device out of standby':
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
If U-Boot is the secondary boot loader, or has been run from itself, the
SOR may already be powered up. Powering it up again causes a hang, so
detect this situation and skip it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Documents the externally visible functions shared between the VOP
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Documents the externally visible functions shared between the HDMI
drivers for the RK3288 and RK3399.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix the warning,
---8<---
CACHE: Misaligned operation at range [3fdffff0, 3fdffffc]
---<8---
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.
Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to avoid future confusion with similary named files, rename
tve.c to tve_common.c. New name better represents the fact that this file
holds code which can be and will be shared between multiple drivers.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The last set of rebases had dropped the 'grf' field from the common
rk_vop. Add this back to un-break the build (and driver).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This commit enables the RK3399 HDMI TX, which is very similar to the
one found on the RK3288. As requested by Simon, this splits the HDMI
driver into a SOC-specific portion (rk3399_hdmi.c, rk3288_hdmi.c) and
a common portion (rk_hdmi.c).
Note that the I2C communication for reading the EDID works well with
the default settings, but does not with the alternate settings used on
the RK3288... this configuration aspect is reflected by the driverdata
for the RK3399 driver.
Having some sort of DTS-based configuration for the regulator
dependencies would be nice for the future, but for now we simply use
lists of regulator names (also via driverdata) that we probe.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To prepare for the addition of RK3399 HDMI support, the HDMI driver is
refactored and broken into a chip-specific and a generic part. This
change adds the internal interfaces, makes common/reusable functions
externally visible and splits the RK3288 driver into a separate file.
For the probing of regulators, we reuse the infrastructure created
during the VOP refactoring... i.e. we simply call into the helper
function defined for the VOP.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Linux driver now supports higher mpixelclock settings.
Add these to rockchip_phy_config[] and rockchip_mpll_cfg[].
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds a driver for the RK3399 VOPs capable and all the
necessary plumbing to feed the HDMI encoder. For the VOP-big, this
correctly tracks the ability to feed 10bit RGB data to the encoder.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To prepare for adding the RK3399 VOP driver (which shares most of its
registers and config logic with the RK3228 VOP), this change refactors
the driver and splits the RK3288-specific driver off.
The changes in detail are:
- introduces a data-structure for chip-specific drivers to register
features/callbacks with the common driver: at this time, this is
limited to a callback for setting the pin polarities (between the
VOP and the encoder modules) and a flag to signal 10bit RGB
capability
- refactors the probing of regulators into a helper function that
can take a list of regulator names to probe and autoset
- moves the priv data-structure into a (common) header file to be
used by the chip-specific drivers to provide base addresses to
the common driver
- uses a callback into the chip-specific driver to set pin polarities
(replacing the direct register accesses previously used)
- splits enabling the output (towards an encoder) into a separate
help function withint the common driver
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces two new Kconfig options that configure the maximum
allowable framebuffer size (i.e. the memory reservation/allocation for
the framebuffer):
- VIDEO_ROCKCHIP_MAX_XRES
- VIDEO_ROCKCHIP_MAX_YRES
The resulting memory allocation will cover 4 byte per pixel for these
resolutions.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For consistency sake (and as we are about to add new options to this
file), reformat the help for VIDEO_ROCKCHIP.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When enabling CONFIG_DISPLAY_ROCKCHIP_HDMI, compile-time warning for
the following implicitly defined functions are raised due to a missing
include directive:
drivers/video/rockchip/rk_hdmi.c: In function 'rk_hdmi_probe':
drivers/video/rockchip/rk_hdmi.c:150:2: warning: implicit declaration of function 'rk_setreg' [-Wimplicit-function-declaration]
rk_setreg(&priv->grf->soc_con6, 1 << 15);
^~~~~~~~~
drivers/video/rockchip/rk_hdmi.c:153:2: warning: implicit declaration of function 'rk_clrsetreg' [-Wimplicit-function-declaration]
rk_clrsetreg(&priv->grf->soc_con6, 1 << 4,
^~~~~~~~~~~~
This change fixes this by including <asm/hardware.h> in rk_hdmi.c.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is good practice to include common.h as the first header. This ensures
that required features like the DECLARE_GLOBAL_DATA_PTR macro,
configuration options and common types are available.
Fix up some files which currently don't do this. This is necessary because
driver model will soon start using global data and configuration in the
dm/read.h header file, included via dm.h. The gd->fdt_blob value will be
used to access the device tree and CONFIG options will be used to
determine whether to support inline functions in the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Newer SoCs use same TV encoder unit. Split it out so it can be reused
with new DM video driver.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to a typo, the 24 bit-per-pixel configuration ends in 24BMP
instead of 24BPP. This change renames it throughout the source tree
for consistency and to make moving these options into Kconfig easier
and less error-prone.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Instead of having drivers/video/rockchip/Kconfig point outside of its
hierarchy for dw_hdmi.o, we should use a configuration-option to
include the Designware HDMI support.
This change introduces a new config option (not to be selected via
menuconfig, but to be selected from a dependent video driver's
configuration option) that enables dw_hdmi.o and selects it whenever
the HDMI support for Rockchip SoCs is selected.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some DVI monitors don't work in HDMI mode. Set it only if edid data
explicitly states that it is supported.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
The variables SEQ_SWRESET, SEQ_ELVSS_ON, SEQ_TEMP_SWIRE, SEQ_APON and
SEQ_SLPIN are unreferenced, drop.
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
plat->size here is used to reserve frame buffer space befor relocation.
our mipi panel use 24 bitwidth, and vop require 32bit align. So the frame
buffer size should be at least 1920*1200*32/8.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Because the bitwidth is different for different display mode, so we need
to set them according to demand.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add mipi display mode for rk3399 vop, so that we can use mipi panel
for display.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It's caused by the difference of clk_set_rate function implement between
rk3288 andd rk3399.
clk_set_rate() of rk3288 return 0 in normal condition.
clk_set_rate() of rk3399 return input parameter in normal condition.
So check clk_set_rate's return value by IS_ERR_VALUE.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Modify Makefile for rockchip video driver according to Kconfig, so that
source code will not be compiled if not needed.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
1. add Kconfig for rockchip video driver, so that video port can be
selected as needed.
2. move VIDEO_ROCKCHIP option to new Kconfig for concision.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Drop indenting in Kconfig:
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the video driver to work with driver model and move over existing
baords. There is no need to keep the old code.
We can also drop setting of CONFIG_FB_ADDR since driver model doesn't have
this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add a function to set the video parameters to the msg handler and remove
it from the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add a function to get the video size to the msg handler and remove it from
the video driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
This converts the following to Kconfig:
CONFIG_SYS_WHITE_ON_BLACK
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Make this default y on various SoCs]
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds support for HDMI output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Video driver for older Allwinner SoCs uses cfb console framework which
in turn uses struct ctfb_res_modes to hold timing informations. However,
DM video framework uses different structure - struct display_timing.
It makes more sense to convert lcdc to use new timing structure because
all new drivers should use DM video framework and older drivers might be
rewritten to use new framework too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TCON unit has similar layout and functionality also on newer SoCs. This
commit splits out TCON code for easier reuse later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
After enabling log printing to lcd, when the screen starts
scrolling, system crashes. Log is shown as bellow:
"Synchronous Abort" handler, esr 0x96000045
"Synchronous Abort" handler, esr 0x96000045
Checking the source code, we found that the variable "pixels"
gets a wrong value:
int pixels = VIDEO_FONT_HEIGHT * vid_priv->line_length;
"pixels" here means the value of pixels for a character, rather
than the bytes for a character. So the variable "pixels" is 4
times bigger than it's exact value, which will cause the memory
overflow when the cpu runs the following code:
for (i = 0; i < pixels; i++)
*dst++ = clr; <<----
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Add common widescreen modes 800x480 and 1024x600.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
DCU_LAYER_MAX_NUM is currently used for DCU_MODE_BLEND_ITER and it
actually overflows the maximum value of BLEND_ITER for Vybrid and
LS102XA. Fix this by using a default value of 2.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
When enabling the DCU and pixel clock, the test mode is activated
since this is the reset configuration. The test mode immediately
shows a red screen on a LCD. A moment later, the DCU gets
initialized properly.
This patch enables the pixel clock after initialization of the DCU
control register. This avoids this initial flicker on LCD screens.
While at it change the polarity of pixel clock to display samples
data on the rising edge.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Fix the framebuffer location to the very end of the available memory.
This allows to remove the area from available memory for the kernel,
which in turn allows to display the splash screen through the Linux
kernel boot process.
Ideas has been taken from the sunxi display driver, e.g.
20779ec3a5 ("sunxi: video: Dynamically reserve framebuffer memory")
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Designware HDMI controller and phy are used in other SoCs as well. Split
out platform independent code.
DW HDMI has 8 bit registers but they can be represented as 32 bit
registers as well. Add support to select access mode.
EDID reading code use reading by blocks which is not supported by other
SoCs in general. Make it more general using byte by byte approach, which
is also used in Linux driver.
Finally, not all DW HDMI controllers are accompanied with DW HDMI phy.
Support custom phys by making controller code independent from phy code.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Nickey Yang <nickey.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Despite the comment in the code, CSC unit is never used. According to
the only public description of DW HDMI controller (i.MX6 manual), CSC
unit is bypassed in MC_FLOWCTRL register and then actually powered
down in MC_CLKDIS register.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Function hdmi_lookup_n_cts() is feed with clock in Hz, which gets
compared with clocks in kHz. Fix that by converting all clocks to Hz.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
"unsigned long" is a lousy data type when it comes to match peripheral
hardware registers with a fixed size.
Just do the obvious and match a 32-bit display format with an "u32"
data type for casting.
This fixes the logo display on 64-bit architectures, which produced
a black line on the right side of the logo with non-black backgrounds.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently the system hangs when the 'videomode' variable is not present
and a reset command is issued:
=> setenv videomode
=> saveenv
=> reset
(Board hangs)
lcdif_power_down() assumes that the LCDIF controller has been properly
configured and enabled, which may not be true.
To fix this issue check whether panel.frameAdrs has been initialized and
in case it has not been initialized, do not continue with the LCDIF
powerdown sequence.
Tested on a imx7dsabresd board.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some files are missing this declaration. Add it to avoid build errors when
we actually need the declaration.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If the splash file doesn't exist, the booting stops bricking
the boards. Check return value of prepare function and stop
decoding the logo data if splash prepare stage failed.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
To enable working efifb support, let's map the frame buffer as 32bpp
instead of 16bpp.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
It makes not sense using u8 to hold a value on a 32-bit or 64-bit machine.
It can only bloat the code by forcing the compiler to mask the value.
Change it to uint.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check whether a display device is in use before using it. Add a comment as
to why two displays cannot currently be used at the same time.
This allows us to remove the device-tree change that disables vopb on
jerry.
Signed-off-by: Simon Glass <sjg@chromium.org>
Mark a display as in use when display_enable() is called. This can avoid
a display being used by multiple video-output devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes the frame buffer is not a multiple of the cache line size.
Adjust the cache-flushing code to avoid cache warnings/errors in this
case.
Signed-off-by: Simon Glass <sjg@chromium.org>
This code incorrectly uses the oscillator. It should use the clock
selected in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 135aa95 (clk: convert API to match reset/mailbox style)
This code currently always selects the second source. It only worked
because both sources are set up.
With the change to only init video devices that are present in the stdout
environment variable, this fails. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Compiling the 'bmp' command with DM and having one of the following macros
enabled:
CONFIG_BMP_16BPP, CONFIG_BMP_24BPP ONFIG_BMP_32BPP
generates this error:
drivers/video/video_bmp.c: In function ‘video_bmp_display’:
drivers/video/video_bmp.c:315:22: error: ‘lcd_line_length’ undeclared (first use in this function)
fb -= width * 2 + lcd_line_length;
^
This patch moves to using the correct variable instead and enables the
'bmp' command for DM again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Anatolij Gustschin <agust@denx.de>
Commit b02e4044ff ("libfdt: Bring in upstream stringlist
functions") broke codying style in some places especially
by inserting an extra whitespace before fdt_stringlist_count().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CONSOLE_SCROLL_LINES
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This should be defined in a header file so that arguments are checked.
Move it to video.h.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CONSOLE_EXTRA_INFO
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VIDEO_SW_CURSOR
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Re-convert, find all the cases where this is off]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_VGA_AS_SINGLE_DEVICE
Once we migrate to driver model for video, we should be able to drop this
option.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is not used in U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_CONSOLE_BG_COL
CONFIG_SYS_CONSOLE_FG_COL
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CFB_CONSOLE_ANSI
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LCD
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This converts the following to Kconfig:
CONFIG_VIDEO
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
These have now landed upstream. The naming is different and in one case the
function signature has changed. Update the code to match.
This applies the following upstream commits by
Thierry Reding <treding@nvidia.com> :
604e61e fdt: Add functions to retrieve strings
8702bd1 fdt: Add a function to get the index of a string
2218387 fdt: Add a function to count strings
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that all x86 boards have been converted to DM video, drop the
legacy drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With DM VESA driver on x86 boards, plat->base/size/align are all
zeroes and starting address passed to alloc_fb() happens to be 1MB
aligned, so this routine does not trigger any issue. On QEMU with
U-Boot as coreboot payload, the starting address is within 1MB
range (eg: 0x7fb0000), thus causes failure in video_post_bind().
Actually if plat->size is zero, it makes no sense to do anything
in this routine. Add such check there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present only chromebook boards are converted to DM video. Other
x86 boards are still using the legacy cfb_console driver. This
switches to use DM version drivers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the samus driver to avoid the direct call to the video BIOS setup.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we use the legacy vesa driver for graphics. Add a driver which
supports driver model. This can be probed only when needed, removing the
need to start up the display if it is not used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
For vidconsole_post_probe(), it is common coding style to let a
probe method return the value of a register function.
The others will become simple wrapper functions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
When the backlight's pwm input is connected to a pwm output of the SoC,
actually use pwm to drive the backlight.
The mean reason for doing this is to fix the backlight turning off
for aprox. 1 second while the kernel is booting. This is caused by
the kernel actually using pwm to drive the backlight, so that it
can dim the backlight. First the pwm driver loads and switches the
pinmux for the pin driving the backlight's pwm input to the pwm
controller. Then about 1s later the actual backlight driver loads
and tells the pwm driver to actually update the pwm settings, which
have a power-on-reset value of "off".
An additional advantage is that this allows us to initatiate the
backlight at 80%, which is the kernel default, avoiding a brightness
change while the kernel loads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed by: Peter Korsgaard <peter@korsgaard.com>
The current code picks the first available clock. In U-Boot proper this is
the oscillator device, not the SoC clock device. As a result the HDMI display
does not work.
Fix this by calling rockchip_get_clk() instead.
Fixes: 135aa950 (clk: convert API to match reset/mailbox style)
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
The CONFIG_HIDE_LOGO_VERSION config can be used to disable putting the
U-Boot version string on top of the logo.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
This seems to give the best performance, so let's use it always.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We have standard drivers for panels and backlights which can do most of the
work for us. Move the tegra20 LCD driver over to use those instead of custom
code.
This patch includes device tree changes for the nvidia boards. I have only
been able to test seaboard. If this patch is applied, these boards will
also need to be synced with the kernel, and updated to use display-timings:
- colibri
- medcom-wide
- paz00
- tec
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Waiting 30 seconds for the hpd to go high seems a bit much, especially
on headless boots. Lowering the timeout to 300ms.
Sending as RFC because frankly i don't know what a sensible timeout is
here, but 30 seconds is clearly not it :)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Reviewed-by: Simon Glass <sjg@chromium.org>
Dropped RFC tag:
Signed-off-by: Simon Glass <sjg@chromium.org>
The following changes are made to the clock API:
* The concept of "clocks" and "peripheral clocks" are unified; each clock
provider now implements a single set of clocks. This provides a simpler
conceptual interface to clients, and better aligns with device tree
clock bindings.
* Clocks are now identified with a single "struct clk", rather than
requiring clients to store the clock provider device and clock identity
values separately. For simple clock consumers, this isolates clients
from internal details of the clock API.
* clk.h is split so it only contains the client/consumer API, whereas
clk-uclass.h contains the provider API. This aligns with the recently
added reset and mailbox APIs.
* clk_ops .of_xlate(), .request(), and .free() are added so providers
can customize these operations if needed. This also aligns with the
recently added reset and mailbox APIs.
* clk_disable() is added.
* All users of the current clock APIs are updated.
* Sandbox clock tests are updated to exercise clock lookup via DT, and
clock enable/disable.
* rkclk_get_clk() is removed and replaced with standard APIs.
Buildman shows no clock-related errors for any board for which buildman
can download a toolchain.
test/py passes for sandbox (which invokes the dm clk test amongst
others).
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add driver-model support to this driver. Most features can be controlled
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Adjust the driver to use struct display_timing for its display timing.
This is what is used by driver-model and allows the LCD init code to be
common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
