Add support for the new Tamonten™ NG platform from Avionic Design.
Currently only I2C, MMC, USB and ethernet have been tested.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Fix the timeout issue after running "bootp" command in u-boot
console. For example you see "EHCI timed out on TD- token=0x...".
TXFIFOTHRES bits of TXFILLTUNING register should be set to 0x10
after a controller reset and before RUN bit is set
(per technical reference manual).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
In config_cmd_default.h, it will use CONFIG_SYS_NO_FLASH to decide
whether include CONFIG_CMD_FLASH and CONFIG_CMD_IMLS. So, move the
CONFIG_SYS_NO_FLASH to proper position, then we don't need to undef
these two commands.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
remove unneeded #undef for at91sam9x5ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch makes the following updates to the cm_t35 config file:
- Replace "ttyS" in default environment kernel bootargs with the new "ttyO"
notation.
- Remove "omapfb.debug=y" from default environment kernel bootargs.
- Define a minimal power-on delay for USB hub ports so that slow-to-power-on USB
sticks will have enough time to become responsive.
- Add support for bootz command
- ulpi_reset is not necessary and always fails with the following error message:
"ULPI: ulpi_reset: failed writing reset bit"
So, remove it.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Stefan Roese <sr@denx.de>
Pin 30 is connected to PHY's RESET# signal, so it must be
put to high. Otherwise PHY won't be found via MDIO interface.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
commit 16297cfb2a
Author: Mateusz Zalega <m.zalega@samsung.com>
Date: Fri Oct 4 19:22:26 2013 +0200
usb: new board-specific USB init interface
introduced a new parameter to the dfu command. Adapt the default environment
for the siemens boards.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Mateusz Zalega <m.zalega@samsung.com>
To make managing the environment easier, add DFUARGS to
CONFIG_EXTRA_ENV_SETTINGS. Then we set DFUARGS down in the DFU part of
the file, and include (or not) the NAND part, based on if NAND is set.
Signed-off-by: Tom Rini <trini@ti.com>
Add SPL U-Boot support to replace x-loader on the Compulab cm_t35
board. Currently only the 256MiB SDRAM board versions are supported.
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The memory size is autodetected and is passed to the Linux kernel
either via ATAGs or device-tree (dtb). So there is no need to
pass it via the bootargs.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add SPL support for the Technexion TAO3530 SOM to replace
x-loader. Tested with the Thunder baseboard. Currently this is
only tested with the TAO3530 SOM revision (Ax/Bx).
Tested by booting via MMC and NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
Add support for TechNexion TAO3530 SoM
This patch has been posted quite a long time ago. I ported it to
the latest mainline U-Boot version. With some additional cleanup
and enhancements.
Signed-off-by: Tapani Utriainen <tapani@technexion.com>
CC: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thorsten Eisbein <thorsten.eisbein@head-acoustics.de>
Cc: Tom Rini <trini@ti.com>
With the current scenario SPL size is being overlapped with the public
stack and not allowing any OMAP4 device to boot. So the suggestion came
up was to move the TEXT_BASE down to non-HS limit. Fixing the same and
also moving the SRAM_SCRATCH_SPACE_ADDR up to the end of image
downloadable area.
Discussion on this can be seen here:
https://www.mail-archive.com/u-boot@lists.denx.de/msg127147.html
Tested on OMAP4460 PANDA.
Reported-by: Chao Xu <caesarxuchao@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
We want to test SPI flash code in the sandbox, so enable the new drivers and
the 'sf test' command.
This command is used to validate the sandbox SPI / SPI flash implementation,
so enable it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for USB-A9263 board manufactured by Calao Systems
(http://www.calao-systems.com/).
Code is based on old U-Boot sources (2010.09) released by Calao.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable support for the siemens AT91SAM9G20 based board corvus.
Signed-off-by: Boris Schmidt <boris.schmidt@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
enable support for the siemens AT91SAM9G20 based boards taurus
and axm.
Signed-off-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes this error message when USB is started.
"ULPI: ulpi_reset: failed writing reset bit"
It is pointless to manually reset the ULPI as the USB Host
Reset and PHY RESET line should take care of that.
Reported-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Roger Quadros <rogerq@ti.com>
arndale board is booted from mmc
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Inderpal Singh <inderpal.singh@linaro.org>
This patch adapts the s3c24x0 driver to the new i2c framework.
Config file is modified for all the boards that use the driver.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
CC: Minkyu Kang <mk7.kang@samsung.com>
CC: Heiko Schocher <hs@denx.de>
CC: Inderpal Singh <inderpal.singh@linaro.org>
CC: David Müller <d.mueller@elsoft.ch>
CC: Chander Kashyap <k.chander@samsung.com>
CC: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
MPC8349 has been using mpc85xx DDR driver through a symbolic link to
mpc85xx_ddr_gen2.c. After consolidating the drivers to a single set
under driver/ddr/fsl/, the link is replaced by referring driver
directly. We now can simply enable the macro and use the driver.
Other mpc83xx SoCs still use their own driver.
Signed-off-by: York Sun <yorksun@freescale.com>
Usually CONFIG_FSL_DDR_INTERACTIVE feature is used for debug.
we would not enable this by default to save the limited space of u-boot.
This avoid following compiling error:
section .bootpg loaded at [00000000effff000,00000000effff577] overlap ssection
.data loaded at [00000000efff31b8,00000000f00010c7]
u-boot: section .bootpg lma 0xeffff000 adjusted to 0xf00010c8
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
In new board P1010RDB-PB, the interrupt vector table is at
the start of memory. So if the start_address needs to be set
a proper value.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Enable FDT support for all Siemens AM335x boards. To support
newer Linux kernels with DT booting.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Lukas Stockmann <lukas.stockmann@siemens.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Heiko Schocher<hs@denx.de>