Add support for the Variscite VAR-SOM-IMX93 evaluation kit. The SoM
consists of an NXP iMX93 dual A55 CPU. The SoM is mounted on a Variscite
Symphony SBC.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Add dedicated Makefile targets for the i.MX93 and a new imx93-u-boot.dtsi
device-tree to create binman images.
Signed-off-by: Mathieu Othacehe <m.othacehe@gmail.com>
Implement fdtdec_board_setup() auto-detection of ethernet PHY.
This uses properties of the hardware and pull resistor placement.
If GPIO1_16 RGMII_MDC is HIGH, then R530 (MX8MM eDM SBC) or
R390 (MX8MP eDM SBC) is populated. R530 or R390 is populated
only on boards with AR8031 PHY.
If GPIO1_16 RGMII_MDC is LOW, then the in-SoM pull down is the
dominant pull resistor. This is the case on boards with BCM54213PE
PHY.
In case AR8031 PHY is populated, the PHY MDIO address is 0, in
case BCM54213PE PHY is populated, the PHY MDIO address is 1, the
fdtdec_board_setup() is used to patch the correct address into
the U-Boot control DT.
Enable broadcom PHY support to support both PHYs.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This restores support for IOT2050 by widely synchronizing its DT files
with the Linux kernel. We additionally need to add the alias restoration
that is still waiting for its upstream merge and the not-yet-upstreamed
bits needed for watchdog reboot detection.
Fixes: 4dbdc84754 ("arm: dts: k3-am654: pull in dtb update from Linux")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Manorit Chawdhry <m-chawdhry@ti.com> says:
K3 devices have firewalls that are used to prevent illegal accesses to
memory regions that are deemed secure. The series prevents the illegal
accesses to ATF and OP-TEE regions that are present in different K3
devices.
AM62X, AM62AX and AM64X are currently in hold due to some firewall
configurations that our System Controller (TIFS) needs to handle.
The devices that are not configured with the firewalling nodes will not
be affected and can continue to work fine until the firewall nodes are
added so will be a non-blocking merge.
Test Logs: https://gist.github.com/manorit2001/4cead2fb3a19eb5d19005b3f54682627
CICD Run: https://github.com/u-boot/u-boot/pull/442
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Tested-by: Thomas Richard <thomas.richard@bootlin.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The following commits adds the configuration of firewalls required to
protect ATF and OP-TEE memory region from non-secure reads and
writes using master and slave firewalls present in our K3 SOCs.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
For readability during configuring firewalls, adding k3-security.h file
and including it in k3-binman.dtsi to be accessible across K3 SoCs
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Andrew Davis <afd@ti.com>
Many nodes are reused between WKUP SPL, MAIN SPL, and U-Boot. Using
bootph-pre-ram is causing these nodes to be present in SPL builds but
pruned away during the U-Boot build. Convert these nodes to bootph-all
so they will remain no matter which dtb build is happening.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu secure proxy node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The dummy_clock node is used to help the drivers probe the IO needed to
setup consoles and boot media to load firmware into the SoC.
This dummy_clock isn't a device that exists nor does it exist in the
mcu domain. So move it from cbass_mcu to the root node to avoid any
confusion.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
These aliases are not needed in U-Boot. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we have duplicate
properties in the root node. Remove them
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate vtt_pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mdio node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The pinmux for usb0 is missing from the Linux board dtb file. Remove it
until we can introduce it in Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate ospi0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate wkup_i2c0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate sdhci1 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have
a duplicate sdhci0 pinmux node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate main_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified we now have a
duplicate mcu_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Ethernet is one of a few IPs in U-Boot that depend on DMA to operate.
However there are a few missing registers ranges in the udmap nodes
need to properly setup DMA for the am65x.
A fix has been added to the Linux kernel[0] to add these ranges however
they have not made it to a Linux tag. To keep DMA operational until the
next DT sync from Linux, add these ranges to the *-u-boot.dtsi with a
note for our future selves.
[0] https://lore.kernel.org/r/20231213135138.929517-2-vigneshr@ti.com
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_udmap node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified, we now have a
duplicate mcu_ringacc node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
timer1 is really just the mcu_timer0 node redefined for the WKUP SPL.
Remove the timer1 and replace it with the mcu_timer0 from the Linux
device tree we imported into U-Boot.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board files unified, we now have a duplicate
wkup_uart0 node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
With the Linux and U-Boot board dtb files unified we now have a
duplicate vtt_supply node. Remove it
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
To make things as organized as possible, start from the Linux board dtbs
and apply all properties needed for U-Boot in our *-u-boot.dtsi file for
the MAIN SPL and U-Boot builds.
We can then include these files for the WKUP SPL build making further
edits to the needed properties and nodes for the WKUP SPL bootloader's
view of the am65x.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
In order to unify the R5 board dtb file with the Linux board dtb file,
we will need to copy all bootph-pre-ram properties to the *-u-boot.dtsi
overlay.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Pull in dtb updates for the am654 base board from v6.7-rc1 of Linux
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
The R5 board file for U-Boot should be the same as the board file copied
from Linux with a few alterations to work with the R5's view of the SoC.
First we need to unify the R5 board file and it's U-Boot overlay before
we can unify the Linux board file with this one.
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
- Make DRAM stable on i.MX8MP DHCOM SoM by using FPWM mode and updating
the DRAM timing
- Fix display artifacts when booting Linux on i.MX8M Mini/Plus eDM SBC
This change configures Toradex Colibri iMX8X SoM USB
hub to bypass mode, and brings out of the reset state.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
This file is included automatically since quite some time now.
From documentation:
U-Boot automatically looks for and includes a file with updates
to the standard devicetree for your board, searching for them in
the same directory as the main file, in this order:
<orig_filename>-u-boot.dtsi
<CONFIG_SYS_SOC>-u-boot.dtsi
<CONFIG_SYS_CPU>-u-boot.dtsi
<CONFIG_SYS_VENDOR>-u-boot.dtsi
u-boot.dtsi
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
This file is included automatically since quite some time now.
From documentation:
U-Boot automatically looks for and includes a file with updates
to the standard devicetree for your board, searching for them in
the same directory as the main file, in this order:
<orig_filename>-u-boot.dtsi
<CONFIG_SYS_SOC>-u-boot.dtsi
<CONFIG_SYS_CPU>-u-boot.dtsi
<CONFIG_SYS_VENDOR>-u-boot.dtsi
u-boot.dtsi
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Add the TPM device found on the GW72xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add the TPM device found on the GW72xx revision F PCB.
This hangs off of SPI2, uses gpio1_10 as a CS and gpio1_11 as RST#.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
-----BEGIN PGP SIGNATURE-----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=aBS6
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-next-20231220' of https://source.denx.de/u-boot/custodians/u-boot-amlogic into next
- Add support for new GXL MDIO mux, with driver and Linux DT sync from v6.4
Since implementation of pinctrl driver for T20 Paz00 can switch
to device tree pinmux setup along with remove of board pinmux
and some minor device tree and defconfig tweaks.
Tested-by: Agneli <poczt@protonmail.ch> # Toshiba AC100 T20
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the downstream kernel.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used for the Linux
device tree and are set according to the service manual.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Drop the pinmux setup in the board in favor of setting it up in
the device tree. Device tree nodes match nodes used in the Linux
device tree.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>