Commit graph

209 commits

Author SHA1 Message Date
vishnupatekar
d5a3357f1b sunxi: Add support for UART0 in PB pin group on A83T
On A83T, PB9,PB10 are UART0 pins.
On allwinner A83T Dev board(h8homlet), this uart0 serial connector
is exposed.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 11:14:21 +01:00
vishnupatekar
762e24a078 sunxi: Add Machine Support for A83T SOC
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.

SMP is not yet supported.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-12-10 11:14:21 +01:00
Siarhei Siamashka
52d093112a sunxi: clock: Set AHB1 clock frequency to 200MHz on Allwinner H3
The 3.4 kernel from the Allwinner SDK is clocking AHB1 at 200MHz
on Allwinner H3 and using PLL6 as the clock source (PLL6/3).
This can be verified by reading the value of the AHB1_APB1_CFG_REG
register via /dev/mem. It always reads as 0x3180 regardless of
the current cpufreq operating point. So this configuration should
be safe for use in U-Boot too.

PLL6 also needs to be configured before it is used as the clock
source, according to the "CCU / Programming Guidelines" section
of the Allwinner manual.

The current low AHB1 clock speed is limiting the USB transfer
speed when booting via FEL. This patch can increase the FEL USB
transfer speed from ~510 KB/s to ~950 KB/s.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
0404d53f2f sunxi: Add H3 DRAM initialization support
Based on existing A23/A33 code and the original H3 boot0.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:31:00 +01:00
Jens Kuske
1c27b7dcd0 sunxi: Add basic H3 support
Add initial sun8i H3 support, only uart + mmc are supported for now.

Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-11-22 11:30:59 +01:00
Nikita Kiryanov
a1e56cf6d4 spl: mmc: add support for BOOT_DEVICE_MMC2
Currently the mmc device that SPL looks at is always mmc0, regardless
of the BOOT_DEVICE_MMCx value. This forces some boards to
implement hacks in order to boot from other mmc devices.

Make SPL take into account the correct mmc device.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-11-18 14:50:05 -05:00
Nikita Kiryanov
36afd45136 spl: change return values of spl_*_load_image()
Make spl_*_load_image() functions return a value instead of
hanging if a problem is encountered. This enables main spl code
to make the decision whether to hang or not, thus preparing
it to support alternative boot devices.

Some boot devices (namely nand and spi) do not hang on error.
Instead, they return normally and SPL proceeds to boot the
contents of the load address. This is considered a bug and
is rectified by hanging on error for these devices as well.

Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tom Rini <trini@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans De Goede <hdegoede@redhat.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Jagan Teki <jteki@openedev.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-11-18 14:50:02 -05:00
Maxime Ripard
f7d6b3cc16 sunxi: board: Only try to use the MMC related functions if enabled
So far, even if CONFIG_MMC was not enabled the board code was trying to use
the MMC-related functions, resulting in linker errors.

Protect those calls by an ifdef.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-10-20 22:48:28 +02:00
Hans de Goede
6944aff1ca sunxi: power: Unify axp pmic function names
Stop prefixing the axp functions for setting voltages, etc. with the
model number, there ever is only one pmic driver built into u-boot,
this allows simplifying the callers.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-10-20 18:40:27 +02:00
Hans de Goede
6d0bdfdde5 sunxi: Switch to using malloc_simple for the spl
common/dlmalloc.c is quite big, both in .text and .data usage. E.g. for a
Mele_M9 sun6i board build this reduces .text from 0x4214 to 0x3b94 bytes,
and .data from 0x54c to 0x144 bytes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-10-20 18:40:27 +02:00
Bernhard Nortmann
af654d1461 sunxi: retrieve FEL-provided values to environment variables
This patch extends the misc_init_r() function on sunxi boards
to test for the presence of a suitable "sunxi" SPL header. If
found, and the loader ("fel" utility) provided a non-zero value
for the boot.scr address, then the corresponding environment
variable fel_scriptaddr gets set.

misc_init_r() also sets (or clears) the "fel_booted" variable depending
on the active boot device, using the same logic as spl_boot_device().

The goal is to provide sufficient information (within the U-Boot
environment) to make intelligent decisions on how to continue the boot
process, allowing specific customizations for the "FEL boot" case.

Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-09-29 11:50:07 +02:00
Hans de Goede
cb42d63554 sunxi: Simplify spl board_init_f function
crt0.S will both memset the bss sectioan and call board_init_r for us,
so there is no need to do either ourselves.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-09-29 11:50:07 +02:00
Chen-Yu Tsai
92369844ec sunxi: Enable non-secure access to RTC on sun6i (A31s)
On the A31s the RTC is by default secured. Thus when u-boot
loads the kernel in non-secure world, the RTC is unavailable. The
SoC has a TrustZone Protection Controller, which can be used to
enable non-secure access to the RTC.

On the A31 the TZPC doesn't seem to do anything, i.e. changes to
its register contents do not affect access to the RTC.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-08-31 08:43:42 +02:00
Hans de Goede
55ea98d8b1 sun6i: clock: Add support for the mipi pll
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:39 +02:00
Hans de Goede
49043cbad1 sunxi: clock: Add clock_get_pll3() helper function
Add a helper function to get the pll3 clock rate.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-14 08:37:38 +02:00
Hans de Goede
c9f8947e66 sunxi: usb-phy: Never power off the usb ports
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.

Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.

This patch removes the powering off calls, fixing the undesirable power
bouncing.

Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-08-08 16:26:19 +02:00
Masahiro Yamada
b0c8f4a797 Kill unneeded #include <linux/kconfig.h>
Because the top-level Makefile forces all the source files
to include include/linux/kconfig.h (see the UBOOTINCLUDE define),
these includes are redundant.

By the way, there are exceptions for the statement above; host
programs.  In fact, host tools in U-Boot depend on a particular
board configuration, although I think they should not.  So, some
files still include <linux/config.h> to work around build errors
on host tools.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Simon Glass <sjg@chromium.org>
2015-07-27 15:02:12 -04:00
Hans de Goede
9ecce9707b sunxi: musb: Stop treating not having a vbus-det gpio as an error
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.

Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-07-25 11:22:55 +02:00
Hans de Goede
48c06c98ec sunxi: usb-phy: Add support for reading otg id pin value
Add support for reading the id pin value of the otg connector to the usb
phy code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-07-25 11:22:54 +02:00
Daniel Kochmański
a151403fd2 sunxi: spl: Detect at runtime where SPL was read from
Make possible using a single `u-boot-sunxi-with-spl.bin` binary for both NAND
memory and SD card. Detection where SPL was read from is implemented in
`spl_boot_device`.

Signed-off-by: Daniel Kochmański <dkochmanski@turtle-solutions.eu>
CC: Roy Spliet <r.spliet@ultimaker.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
[hdegoede@redhat.com: Some small coding style fixes]
Acked-by: Hans De Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-24 16:17:08 +02:00
Wang Dongsheng
972af2ab51 ARMv7: Factor out reusable timer_wait from sunxi/psci_sun7i.S
timer_wait is moved from sunxi/psci_sun7i.S, and it can be converted
completely into a reusable armv7 generic timer. LS1021A will use it
as well.

Signed-off-by: Wang Dongsheng <dongsheng.wang@freescale.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-07-20 11:44:38 -07:00
Chen-Yu Tsai
e506889c96 sunxi: Add support for UART0 in PB pin group on A33
The A33 adds a pinmux function for UART0 in the PB pin group.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-05 11:32:11 +02:00
Chen-Yu Tsai
dec7c84227 sunxi: rsb: Enable R_PIO clock before configuring external pins
The original code was configuring the external pins after enabling
the R_PIO clock, which meant the configuration never made it to
the pin controller the first time in SPL.

Why this was working before is uncertain. Maybe the state was left
from a previous boot sequence, or RSB just happened to be the default
configuration. However with some A33 chips, SPL failed to configure
the PMIC. This was seen by me and Maxime on the Sinlinx SinA33 dev
board.

Reordering the calls fixed this.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-05 11:32:11 +02:00
Chen-Yu Tsai
6ad8c74300 sunxi: hardware-feature-specific function index defines for PORT F UART0
Commit 487b327 ("sunxi: GPIO pin mux hardware-feature-specific function
index defines") renamed all GPIO index defines, but missed the PORT F
UART0 setup functions.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-07-05 11:32:11 +02:00
Ian Campbell
da9971d1b3 Revert "sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory"
This reverts commit f76eba38b3.

This patch did not have a full and proper copyright/S-o-b chain.

Signed-off-by: Ian Campbell <ijc@hellion.org.uk>

Conflicts:
	include/configs/sun6i.h
	include/configs/sun8i.h
2015-06-28 11:46:31 -04:00
Hans de Goede
fc175434f9 sun6i: cpu_reset: Do not return from cpu_reset()
Currently on sun6i after a "reset" the prompt returns and the user can
even type stuff until the watchdog triggers and does the actual reset.

This is somewhat unexpected behavior for the "reset" command, this
commit adds an endless loop to wait for the watchdog to trigger so that
we do not return to the prompt.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-17 15:22:47 +02:00
Hans de Goede
8aeed95626 sunxi: Request macpwr gpio before using it
This fixes ethernet no longer working on boards which use a gpio to enable
the phy.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-10 16:52:12 +02:00
Hans de Goede
7afebb5b29 sunxi: usb_phy: Swap check for disconnect threshold
Before this commit the code for determining the disconnect threshold was
checking for sun4i or sun6i assuming that those where the exception and
that newer SoCs use a disconnect threshold of 2 like sun7i does.

But it turns out that newer SoCs actually use a disconnect threshold of 3
and sun5i and sun7i are the exceptions, so check for those instead.

Here are the settings from the various Allwinner SDK sources:
 sun4i-a10: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun5i-a13: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
 sun6i-a31: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun7i-a20: USBC_Phy_Write(usbc_no, 0x2a, 2, 2);
 sun8i-a23: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun8i-h3:  USBC_Phy_Write(usbc_no, 0x2a, 3, 2);
 sun9i-a80: USBC_Phy_Write(usbc_no, 0x2a, 3, 2);

Note this commit makes no functional changes for sun4i - sun7i, and
changes the disconnect threshold for sun8i to match what Allwinner uses.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-06-04 14:11:01 +02:00
Chen-Yu Tsai
9816743031 ARM: sunxi: Share sun6i PSCI backend with sun8i
sun8i can share the PSCI backend with sun6i. Only difference
is sun8i does not have CPU power clamp controls.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Chen-Yu Tsai
073f298438 ARM: sunxi: Add sun6i specific PSCI implementation
This adds PSCI support for sun6i. So far it only supports
the PWR_ON method.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Chen-Yu Tsai
d4611aff4d ARM: sunxi: Make PSCI code sun7i specific
The PSCI code only works for sun7i. Rename it with _sun7i suffix,
and build only if building for sun7i.

This paves the way for adding PSCI support for other platforms.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Chen-Yu Tsai
4ffd624512 ARM: sunxi: Document registers in PSCI code
The PSCI CPU_ON code accesses quite a few registers. Document
their names to make it easier to cross reference.

Also explain "lock cpu" and "unlock cpu" as enabling/disabling
debug access.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Daniel Kochmański
f76eba38b3 sunxi/nand: Add support to the SPL for loading u-boot from internal NAND memory
This commit adds support to the sunxi SPL to load u-boot from the internal
NAND. Note this only adds support to access the boot partitions to load
u-boot, full NAND support to load the kernel, etc. from the nand data
partition will come later.

Signed-off-by: Roy Spliet <r.spliet@ultimaker.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-29 13:46:36 +02:00
Hans de Goede
1871a8ca62 sun9i: Basic sun9i (A80) support
Add initial sun9i (A80) support, only uart + mmc are supported for now.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Hans de Goede
93fc39a7c3 sunxi: Remove support for building "old-fashioned" fel binaries
The latest versions of the fel tool support loading normal u-boot builds
directly, and this is now the preferred way to use the fel boot method.

This commit removes support for the old deprecated standalone fel builds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Hans de Goede
813598e3b4 sunxi: Use axp221 sid on a33
Unlike the A31 and the A23 the A33 actually has a SID inside the SoC again,
but sid[3] is 0 (at least on some SoCs), so it is better to use the axp221
sid.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-29 13:46:36 +02:00
Hans de Goede
8975cdf4bc sunxi: Make DRAM_ODT_EN Kconfig setting a bool
Make DRAM_ODT_EN Kconfig setting a bool, add a separate DRAM_ODT_CORRECTION
setting for A23 SoCs and use DRAM_ODT_EN Kconfig everywhere instead of
only in dram_sun4i.c and hardcoding odt_en elsewhere.

Note this commit makes no functional changes for existing boards,
its purpose is to allow changing the odt_en value on future A33 boards.

For sun4i/sun5i/sun7i boards which set DRAM_ODT_EN=y (which no defconfigs
currently do) this patch turns on odt for both the DQ and the DQS lines,
whereas previously it was possibly (but not desirable) to turn odt on only
for one of them by setting the in DRAM_ODT_EN option to 1 or 2 instead of 3.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2015-05-19 18:46:44 +02:00
Hans de Goede
a881db09c0 sunxi: Fix dram initialization not working on some a33 devices
When porting the allwinner dram init code to u-boot we missed some code
setting an extra bit when doing auto dram config.

This commits add this bit, fixing dram init not working on the ga10h
10" a33 tablet which I'm bringing up atm.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-19 18:37:30 +02:00
Laurent Itti
5cd83b11f9 sunxi: add support for UART2 on A23/A33
Add support for UART2 (2-pin version but note that RTS/CTS pins are available
pn that port for possible future use), can be selected in config
by using CONFIG_CONS_INDEX=3

Signed-off-by: Laurent Itti <laurentitti@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-19 18:37:30 +02:00
Jan Kiszka
3317b988b1 ARM: Put target PC for PSCI CPU_ON on per-CPU stack
Use a per-CPU variable for saving the target PC during CPU_ON
operations. This allows us to run this service independently on targets
that have more than 2 cores and also core-local power control.

CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:14 -07:00
Jan Kiszka
4c681a3d22 ARM: Factor out reusable psci_get_cpu_stack_top
This algorithm will be useful on Tegra as well, plus we will need it for
making _psci_target_pc per-CPU.

CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:14 -07:00
Jan Kiszka
4ce4de1e66 ARM: Factor out reusable psci_cpu_entry
_sunxi_cpu_entry can be converted completely into a reusable
psci_cpu_entry. Tegra124 will use it as well.

As with psci_disable_smp, also the enabling is designed to be overloaded
in cased SMP is not controlled via ACTLR.

CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:13 -07:00
Jan Kiszka
b0206e7d26 ARM: Factor out reusable psci_cpu_off_common
Move parts of sunxi's psci_cpu_off into psci_cpu_off_common, namely
cache disabling and flushing, clrex and the disabling of SMP for the
dying CPU. These steps are apparently generic for ARMv7 and will be
reused for Tegra124 support.

As the way of disabled SMP is not architectural, though commonly done
via ACLTR, the related function can be overloaded.

CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:13 -07:00
Jan Kiszka
680f396851 ARM: Factor out common psci_get_cpu_id
Will be required for obtaining the ID of the current CPU in shared PSCI
functions. The default implementation requires a dense ID space and only
supports a single cluster. Therefore, the functions can be overloaded in
cases where these assumptions do not hold.

CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2015-05-13 09:24:13 -07:00
Hans de Goede
fd01ae1384 sunxi: usb: Protect phy-init and phy-power-on against multiple calls
Once we add support for the ohci controller the phy-init and phy-power-on
functions may be called twice (once by the ehci code and once by the ohci
code) protect them against this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
e13afeef6f sunxi: usb: Do not call phy_probe from hcd code
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.

Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.

Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
2aacc4239c sunxi: usb: Rename the usbc.? files to usb_phy.?
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
7b798658b2 sunxi: usb: Rename sunxi_usbc_foo functions to sunxi_usb_phy_bar
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.

This patch purely renames things, it contains no functional changes.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:55 +02:00
Hans de Goede
a781c97aaa sunxi: usb: Remove sunxi_usbc_get_io_base function
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.

This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
375de01702 sunxi: usb: Move setup of host controller clocks to the host controller drivers
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.

This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
d17e1577a2 sunxi: emac: Remove non driver-model code
All sunxi boards now use the driver-model, so remove the non driver-model
code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:54 +02:00
Hans de Goede
939ed1cba8 sunxi: emac: Add driver model support
Modify the sunxi-emac eth driver to support driver model.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-05-04 16:51:53 +02:00
Hans de Goede
a536077def sunxi: axp: Add support for i2c based PMICs to the pmic-bus helpers
Add support for the axp152 and axp209 PMICs to the pmic register access
helpers. This is a preparation patch for moving the axp gpio code to a
separate gpio driver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Hans de Goede
1d624a4f08 sunxi: axp: Move axp pmic register helpers to a separate file
Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:53 +02:00
Hans de Goede
a725426929 sunxi: usbc: Fix vbus gpio handling to work with the driver-model
The driver-model gpio functions may return another value then -1 as error,
make the sunxi usbc properly handle this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:52 +02:00
Vishnu Patekar
8c3dacff14 sunxi: Add basic A33 basic support
Enable full support for the A33 SoC including display, otg-usb, etc.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Vishnu Patekar
ffc0ae0c70 sunxi: Add a33 dram init code
Based on Allwinner dram init code from the a33 bsp:
https://github.com/allwinner-zh/bootloader/blob/master/basic_loader/bsp/bsp_for_a33/init_dram/mctl_hal.c

Initial u-boot port by Vishnu Patekar, major cleanup / rewrite by
Hans de Goede.

Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
886a7b45ef sunxi: Add support for A33 PLL11 (second DRAM pll)
Add support for the new second DRAM PLL found on the A33 SoC.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
5e6bacdb84 sunxi: s/sun8i/sun8i_a23/
This is a preparation patch for adding A33 support, which will have a
mach name of sun8i-a33.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
44d8ae5b69 sunxi: Introduce a hidden SUNXI_GEN_SUNxI Kconfig bool
sun6i and newer (derived) SoCs such as the sun8i-a23, sun8i-a33 and sun9i
have a various things in common, like having separate ahb reset control
registers, the SID living inside the pmic, custom pmic busses, new style
watchdog, etc.

This commit introduces a new hidden SUNXI_GEN_SUN6I Kconfig bool which can be
used to check for these features avoiding the need for an ever growing list
of "#if defined CONFIG_MACH_SUN?I" conditionals as we add support for more
"new style" sunxi SoCs.

Note that this commit changes the behavior of the gmac and hdmi code for
sun8i and the upcoming sun9i devices. This does not matter as sun8i does
not have gmac nor hdmi, and sun9i has new hardware-blocks for these so
the old code will not work there.

Also this is intentional as if a sun8i / sun9i variant which does use the
old hwblocks shows up then the GEN_SUN6I code paths will be the right ones
to use.

For completeness this also adds a SUNXI_GEN_SUN4I bool for A10/A13/A20.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 16:51:51 +02:00
Hans de Goede
929b2622eb sunxi: usbc: Remove unused irq field
We do not use irqs in u-boot so remove the unused irq field, and all the
 #ifdef-ery around the irq initialization.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 11:59:21 +02:00
Hans de Goede
92bcc6cb1e sunxi: Also set Auxiliary Ctl SMP bit in SPL
There is no reason not to and this make the #ifdef-ery easier to read.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-05-04 11:59:21 +02:00
Jan Kiszka
dcfa530f09 sun7i: Remove duplicate call to psci_arch_init
This is already invoked a few cycles later in monitor mode by
_secure_monitor (_sunxi_cpu_entry calls _do_nonsec_entry which triggers
_secure_monitor via smc #0). Drop it here, it serves no purpose.

CC: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Tested-by: Ian Campbell <ijc@hellion.org.uk>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-05-02 11:50:19 +02:00
Hans de Goede
a0e2b1b865 sunxi: usbc: Wait for vbus to fall after disabling it
When u-boot boots the board may be powering vbus, we turn off vbus in
sunxi_usbc_request_resources, if we are too quick with reading vusb-detect
after this we may see a residual charge and assume we've an external vusb
connected even though we do not. So when we see an external vusb wait a bit
and try again.

Without this when dealing with a pmic controller vbus and doing "reset" on
the u-boot console the musb host will only init once every other boot, because
the other boot it thinks an external vbus is present, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-15 16:17:17 +02:00
Hans de Goede
046ea8b390 sunxi: usbc: Initialize vusb value on request_resources
On boards which use the pmic to enable/disable vbus on the otg port, the
vbus value is not reset to 0 on reset, as reset only resets the SoC and not
the pmic, so explicitly set vbus to 0 on init (request_resources) by moving
the gpio_direction_output call into request_resources.

For consistency also move the gpio_direction_input call for vbus-detect into
request_resources.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
487b3277d4 sunxi: GPIO pin mux hardware-feature-specific function index defines
Each hardware feature exposed through the GPIO pin mux is usually using the same
function index (for a given port), so there is no need to define one value per
pin: one value per hardware feature per port is sufficient, avoids duplication
and makes everything easier to understand.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
ebd468b2d2 sunxi: common VBUS detection logic in usbc
VBUS detection could be needed not only by the musb code (to prevent host mode),
but also by e.g. gadget drivers to start only when a cable is connected.

In addition, this allows more flexibility in vbus detection, as it could easily
be extended to other USBC indexes. Eventually, this would help making musb
support independent from a hardcoded USB controller index (0).

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Paul Kocialkowski
5eaacb4340 sunxi: usb: Drop AXP-sepcific VBUS detection and drive logic
VBUS detection and enable is now be used with virtual AXP GPIOs, so all the USB
code has to use GPIO in every case and let sunxi_gpio do the heavy lifting.

Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-04-15 16:17:17 +02:00
Iain Paton
e71b422bd7 sunxi: use CONFIG_SYS_CLK_FREQ to set cpu clock
make the CPU clock selectable via Kconfig

this removes the sunxi specific CONFIG_CLK_FULL_SPEED defined in each
soc header and replaces it's use in board/sunxi/board.c with
CONFIG_SYS_CLK_FREQ from Kconfig which allows us to configure board
specific frequency on boot

Signed-off-by: Iain Paton <ipaton0@gmail.com>
[hdegoede@redhat.com s/CONFIG_SYS_CLK_FREQ/CONFIG_TIMER_CLK_FREQ/ for the
 arch-timer clk speed on sun7i to fix mis-compile on sun7i]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29 13:36:03 +02:00
Iain Paton
7a140117ef sunxi: sun4i: improve cpu clock selection method
clock_set_pll1 would pick the next highest available cpu clock speed if
a value not in the pre defined table was selected. this potentially
results in overclocking the soc.

reverse the selection method so that we select the next lowest speed
and add the missing 912Mhz setting that's requested by sun7i which also
uses the sun4i clock code.

Signed-off-by: Iain Paton <ipaton0@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-03-29 13:08:39 +02:00
Hans de Goede
246e3b8787 sunxi: musb: Fix some lo speed devices not working with musb host
The usb0 / otg phy on sunxi boards has a bug where it wrongly detects a
high speed squelch on usb reset deassert when a lo speed device is plugged in.

The android kernel has a work around for this in the form of temporary
disabling the phy's squelch detection on reset deassert, this commit adds
the same workaround to the u-boot sunxi musb code, thereby fixing various usb
lo speed devices not working.

Tested with a (before non working) usb keyboard and a usb 2.4 GHz wireless
keyboard/mouse combo receiver.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-03-29 12:58:59 +02:00
Siarhei Siamashka
840fe95c3b sunxi: Support the FEL boot mode in the regular u-boot build
So that the CONFIG_SPL_FEL option is not needed anymore. And the regular
SPL binary, generated by the default u-boot build, is now also bootable
over USB in the FEL mode. The SPL still can boot from the SD card too.

A bunch of system registers need to be saved/restored in order to ensure
that the IRQ handler still works in the BROM FEL code after getting
control back from the SPL. This is done in the sunxi code instead of
abusing ifdefs in 'start.S'.

The decision whether to load the main u-boot binary from the SD card or
return to the FEL code in the BROM is done at runtime.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[hdegoede@redhat.com: Since we now restore various regs before returning to
 the FEL BROM code we can drop the sunxi specific #ifdefs in start.S]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:23:52 +01:00
Simon Glass
942cb0b6a2 sunxi: Normalise FEL support
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.

This series is available at u-boot-dm, branch sunxi-working.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-02-16 20:15:09 +01:00
Hans de Goede
51637afe98 sunxi: dram: Un-inline dram helper functions
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2015-02-16 20:05:52 +01:00
Hans de Goede
37d46dd3c4 sunxi: rsb: Move rsb_set_device_mode() call to rsb_init()
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
d35488c735 sunxi: rsb: Add sun9i (A80 support)
Add support for the A80 to the rsb code.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-02-02 13:55:14 +01:00
Hans de Goede
dacc0881ac sun9i: Add sun9i (A80) clock setup support
Add initial sun9i (A80) clock setup support, enough to get the uart + mmc
going.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
22b618346a sunxi: Drop pll6 setting from clock_init_uart
As the comment says now that we have SPL support this is no longer necessary,
as PLL6 is already setup with the exact same parameters by the SPL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-22 12:34:55 +01:00
Hans de Goede
b56f6e2b4e sunxi: Restore lowlevel_init usage
2 recent sunxi changes have removed the usage of lowlevel_init by moving some
code around and then setting CONFIG_SKIP_LOWLEVEL_INIT.
This is problematic for 2 reasons:

1) It does not just stop s_init from being called, it also stops
cpu_init_cp15 from getting called, which is undesirable.

2) We want u-boot.bin to be usable standalone, without SPL, some people e.g.
use an upstream u-boot.bin together with Allwinner's boot0 loader. So
u-boot.bin must (re)initialize the gpios, timer, etc.

This commit restores the lowlevel_init / s_init usage, while keeping the
changes to no longer use the global-data (gd) struct in the SPL.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-21 10:46:28 -05:00
Simon Glass
2b7c0f3081 sunxi: Drop use of lowlevel_init()
This does nothing now, so drop it. We have SPL anyway to do our low-level
init.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-16 14:52:53 -05:00
Simon Glass
f630974ccb sunxi: Move SPL s_init() code to board_init_f()
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.

There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only change is that we need our own
implementation of board_init_f() which sets up DRAM before the BSS (which
is in DRAM) is cleared.

The s_init() code runs once for SPL and again for U-Boot proper. We
shouldn't need to init the clock/timer/gpio/i2c init twice, so just have it
in SPL.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-16 14:52:52 -05:00
Hans de Goede
a90e77dbeb sunxi: usbc: Add support for usb-vbus0 controller by axp drivebus pin
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Hans de Goede
4458b7a6e1 sunxi: usbc: Add support for usb0 to the common usbc code
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Hans de Goede
0eccec4ef1 sunxi: Move usb-controller init code out of ehci-sunxi.c for reuse for otg
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.

While at it also update various #ifdefs / defines for sun8i support.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Jan Kiszka
05c4bd3ec3 sun7i: Move psci_arch_init close to text_end
"adr rX, text_end" only works if the label is close. Adding further code
to the other functions will prevent this. So move the containing
function close to label. No functional change.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Jan Kiszka
602fa46c2c sun7i: Add support for taking CPUs offline via PSCI
Based on the original version by Marc Zyngier. It adds a psci_cpu_off
implementation for the A20 SoC. The mechanism works by first preparing
the calling CPU to go offline (disable and flush cache, disable SMP),
then requesting CPU 0 to pull the plug. The request is sent as FIQ on
SGI15.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:40 +01:00
Hans de Goede
25508ab26c sunxi: Fix PLL1 running at half speed on sun8i
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Siarhei Siamashka
c3d2b963c6 sunxi: Fix buggy sun6i/sun8i DRAM size detection logic
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).

The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:

/***** A testcase for reproducing the problem ******/

void main(int argc, char *argv[])
{
    size_t size, i;
    uint32_t *buf;
    /* Allocate the buffer */
    if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
                    !(buf = malloc(size))) {
        printf("Need buffer size in MiB as a cmdline argument\n");
        exit(1);
    }
    /* Fill it with the Allwinner DRAM "magic" values */
    for (i = 0; i < size / 4; i++)
        buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
    /* Try to reboot */
    system("reboot");
    /* And wait */
    for (;;) {}
}
/***************************************************/

If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.

A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2015-01-14 14:56:37 +01:00
Hans de Goede
08fd1479c7 sun8i: Add dram initialization support
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
5665f50e81 sunxi: Fill memory before comparing it when doing dram init on sun6i
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.

This commit fixes this by filling the memory with a unique, distinct pattern.

The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.

While at it move mctl_mem_matches to dram.h for re-use in sun8i too.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
07f4fe7d7d sunxi: Move await_completion dram helper to dram.h
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
1aac47bd1b sun6i: clock_set_pll5: Calculate k and m rather then hardcoding them
Our old hardcoded k and m values are based on PLL5 being configured in steps
of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the
DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i)
the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps.

This commit adjusts clock_set_pll5 to automatically select the best k and m
depending on the requested clk rate.

Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
5af741f1e9 sun6i: Add a sigma_delta_enable paramter to clock_set_pll5()
The sun8i dram code sometimes wants to enable sigma delta mode,
add a parameter to allow this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:37 +01:00
Hans de Goede
bdcdf84631 sunxi: axp221: Add axp223 support
The axp223 appears to be the same as the axp221, except that it uses the
rsb to communicate rather then the p2wi. At least all the registers we use
are 100% the same.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
66ebea06f7 sunxi: Add support for the rsb (Reduced Serial Bus)
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.

This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
ce881076fc sun6i: s/SUNXI_*P2WI*/SUN6I_*P2WI*/
The p2wi interface is only available on sun6i, adjust the gpio pinmux and
base address defines for it to reflect this.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Jan Kiszka
3f6242eb30 sunxi: Align PSCI stack calculation to comment
0x400 is true 1K.

Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
cac5b1cc0d sunxi: Add sunxi_get_sid helper function
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.

This makes our MAC address generation code also work on sun6i.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
7582e39eb0 sun6i: dram: Do not try to initialize a second dram chan on A31s
The A31s only has one dram channel, so do not bother with trying to initialize
a second channel.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00
Hans de Goede
10191ed098 sun6i: Add sunxi_get_ss_bonding_id() function
Add a sunxi_get_ss_bonding_id() function, and use it to differentiate between
the A31s and the A31.

Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
2015-01-14 14:56:36 +01:00