Commit graph

1069 commits

Author SHA1 Message Date
Michal Simek
fa822ad19e arm64: zynqmp: Add support for SC revC
System controller revC is using ADI ethernet phy instead of TI because of
supply chain issues.
Describe reset assert and de-assert times to 10us and 5ms respectively
according to the datasheet. Also setup RGMII RX and TX delay values to
2400ps as per board bring up observations.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2790f6cede7485556d581ab8270dda477fa21522.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
64f5e3b492 arm64: zynqmp: Create description for generic SC (vpk120-revB)
System controllers are pretty much the same on the all boards that's why
use autodetection based on i2c eeprom. This should end up with having only
one BSP for all SCs with only DT overlays to cover different i2c
structures.

All MIOs are fixed by the spec that's why not a problem to description
pinctrl setting.

Apart from eth phy reset, it also set proper phy delays.
The TI DP83867 PHY datasheet says:
T1: Post RESET stabilization time == 195us
T3: Hardware configuration pins transition to output drivers == 64us
T4: RESET pulse width == 1us
So with a little overhead set 'reset-assert-us' to 100us (T4) and
'reset-deassert-us' to 280us (T1+T3).

NOTE: The tuning of TI DP83867 phy reset delay is derived from linux
upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron
pitx-imx8m board).

i2c structure on Xilinx Versal evaluation platforms contain a lot of
devices but also connection to connectors like SFP. Because of this
complicated structure with also all level shifters, i2c muxes, etc. not all
devices are able to reliably work on 400kHz even if they are compatible
with this speed. That's why set i2c frequency to 100KHz to increase
reliability of the i2c bus.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
fe90ce2368 arm64: zynqmp: Add support for vpk120-revA
Board contains two systems. The primary is Versal VP1202 ACAP device and
the secondary is ZynqMP zu4 which acts as system controller. The patch is
describing only ZynqMP system controller part.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/bd8b79d7c6693e90e12bce422f8ed00f2f43c9ae.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
96e98b0264 arm64: zynqmp: Add x-prc-01/02/03/04/05 revA support from SC
Add i2c accessible devices with description.
There is versal specific eeprom and i2c-gpio controller.

SE3 has also clock chip present.

Also remove x-prc description from SC dts.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4f71ec6a63240fd4aaa3453824138281c50d71c3.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:30 +02:00
Michal Simek
46f0408771 arm64: zynqmp: Add support for vck190 revB system controller
There are some changes between revA and revB boards. u39 8T49N240 was
removed and also three ina226 at 42/43/44 addresses (u178/u180/u182).

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/461cfe5b2b882365413f90d19efd8abcd6be56ed.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:29 +02:00
Michal Simek
7771873ab4 arm64: zynqmp: Add support for KD240 Kria SOM CC
Add support for KD240 Kria SOM CC. It is pretty much subset of KR260 board
from PS perspective.

Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/835f1d1b8982d46b902db69daad64e8445c051e9.1695808407.git.michal.simek@amd.com
2023-10-09 12:12:29 +02:00
Robert Nelson
45b0b5e5a0 arm: dts: Add k3-am625-beagleplay
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.

This board family can be identified by the 24c32 eeprom:

[aa 55 33 ee 01 37 00 10  2e 00 42 45 41 47 4c 45  |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d  00 00 30 32 30 30 37 38  |PLAY-A0-..020078|]

https://beagleplay.org/
https://git.beagleboard.org/beagleplay/beagleplay

baseline of base device tree is v6.5-rc1.

Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2023-09-08 10:07:12 -04:00
Tom Rini
c37be6a39a First set of u-boot-at91 features for the 2023.10 cycle
-----BEGIN PGP SIGNATURE-----
 
 iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
 aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
 Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
 kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
 +Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
 s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
 tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
 +fcB
 =L/iw
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next

First set of u-boot-at91 features for the 2023.10 cycle:

This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
2023-08-30 09:32:10 -04:00
Tom Rini
2d8e7ac320 ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
 has some other minor enhancements, such as enabling the poweroff command
 on several Tegra210 and Tegra186 boards.
 -----BEGIN PGP SIGNATURE-----
 
 iQJHBAABCAAxFiEEiOrDCAFJzPfAjcif3SOs138+s6EFAmTfWrITHHRyZWRpbmdA
 bnZpZGlhLmNvbQAKCRDdI6zXfz6zoYPFD/9hw40HjaAXf6cD960HWSlcGuNOIV99
 A9JoSgHipCuhACr0z7s4MpbATjEgknZUblJNiVdhzCWAgW3Spy9JpSxMyKlpqdiH
 7Z971DuaXFX9ZCilX9g6whZI/RDglpUEjt3cb4PWrznM6dpKA73voizo+czBeXd7
 AhxTN/2I89VLz75RyR+X41bLLK1VuGND+uGHz/DDbpMXEW8gVRtZ8gnJPeR4zg1y
 EUacNFc+PVjghMFZGmClnw0pXkq2akKp5cJ/A+11aa/Q7FII63v5/Np79kDtnUje
 GPSdg4yqSr1ZE/6qK0qV58B2KKHfeg+6GC47s46KjzaUwL4De64zHtCt6t37zz8y
 hngeeR5SYIKR8HkpXKM8DsMv0D1WciP2awggFPaPF802H/5GMVCnEFITmuFlOuAe
 Q1lg2acywMo2NFINMOONuQahGIJZORpm2VMonMhlesyAuc89quslt/iYSAoV9E4/
 Pt1AqgeOpUh5I236EygJJ11V2BAXkwzR6RazFDr3AHCqB9iFW/UNS1Y7A1pXwKYN
 IVUWU8xkuYYSyxeGwuIrTj/JdQhwfO0jn+xn5g+rUPWNP5n4FJ2oBVPOInfEpled
 k0HgxcGK6Z0hBCwd6/t03QQJWD47/r5jAd9x1eLRFWYV8ivl2Acvm+MlkPx81weG
 E1h7UKdfvTZcDw==
 =Bzgn
 -----END PGP SIGNATURE-----

Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra

ARM: tegra: Changes for v2023.10-rc1

This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
2023-08-18 10:05:04 -04:00
Andy Yan
bb38db086c rockchip: rk3568: Add EmbedFire Lubancat 2 support
LubanCat2 is a rk3568 based SBC from EmbedFire.

Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header

The dts file is sync from linux mainline.

Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-08-12 10:17:59 +08:00
Mihai Sain
87d1cac49d board: at91: sama5d29_curiosity: add initial support for sama5d29_curiosity
Add initial support for sama5d29_curiosity board.

Hardware:
SoC: SAMA5D29 500 MHz
DRAM: LPDDR2 512 MiB
PMIC: MCP16502
Debug: UART0
Flash: QSPI NOR 8 MiB
RGB LCD connector
Mikrobus connectors x 2
SD-Card connectors x 2
USB 2.0 x 2

Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
2023-08-07 11:42:16 +03:00
Marcel Ziswiler
7d1a10659f board: toradex: add verdin am62 support
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.

The device trees were taken straight from Linux v6.5-rc1.

Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
  ---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
2023-08-04 15:03:42 -04:00
Weijie Gao
bc4adc97cf board: mediatek: add MT7988 reference boards
This patch adds general board files based on MT7988 SoCs.

MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:

1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD

Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
2023-08-03 09:40:50 -04:00
Jonas Karlman
1f54f71b18 board: rockchip: Add Radxa E25 Carrier Board
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.

Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA

Device tree is imported from linux next-20230728.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
2023-07-31 20:34:32 +08:00
Eugen Hristev
b8fc65473a board: rockchip: add Radxa ROCK5A Rk3588 board
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.

There are tree variants depending on the DRAM size : 4G, 8G and 16G.

Specifications:

     Rockchip Rk3588S SoC
     4x ARM Cortex-A76, 4x ARM Cortex-A55
     4/8/16GB memory LPDDR4x
     Mali G610MC4 GPU
     MIPI CSI 2 multiple lanes connector
     4-lane MIPI DSI connector
     Audio – 3.5mm earphone jack
     eMMC module connector
     uSD slot (up to 128GB)
     2x USB 2.0, 2x USB 3.0
     2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
     Gigabit Ethernet RJ45 with optional PoE support
     40-pin IO header including UART, SPI, I2C and 5V DC power in
     USB PD over USB Type-C
     Size: 85mm x 56mm (Raspberry Pi 4 form factor)

Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")

Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 17:34:43 +08:00
Jonas Karlman
6855fa625c board: rockchip: Add Pine64 SOQuartz on CM4-IO
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:36 +08:00
Jonas Karlman
d0026e5908 board: rockchip: Add Pine64 SOQuartz on Blade
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
651492bfb2 board: rockchip: Add Pine64 SOQuartz on Model A
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.

Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
f52452bbea board: rockchip: Add Pine64 Quartz64-B Board
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.

Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Jonas Karlman
9c1b5d163e board: rockchip: Add Pine64 Quartz64-A Board
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.

Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host

Device tree is imported from linux v6.4.

Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:41:35 +08:00
Pegorer Massimo
ffd41939fe rockchip: rk3308: fix same-as-spl boot order
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.

Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.

Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-31 14:38:59 +08:00
Jonas Karlman
94da929b93 board: rockchip: Add Hardkernel ODROID-M1
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.

Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host

Device tree is imported from linux v6.4.

Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Christopher Obbard
0022461ba6 arm: rockchip: Add Radxa ROCK 4SE
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.

Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")

Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:03 +08:00
Jagan Teki
fcf5a3c900 arm64: dts: rockchip: Add rk3588 Edgeble Neu6B
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.

General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT

Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.

General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion

Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.

Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")

Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
6a73211d4b rockchip: rk3568: Add support for FriendlyARM NanoPi R5C
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.

Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V

The device tree is taken from kernel v6.4-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
0ef326b5e9 rockchip: rk3568: Add support for FriendlyARM NanoPi R5S
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.

Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector

The device tree is taken from kernel v6.4-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
9bd954ab8a rockchip: rk3328: Add support for Orange Pi R1 Plus LTS
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.

The device tree is taken from kernel v6.4-rc1.

Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-07-28 18:45:02 +08:00
Tianling Shen
69e16c7b1c rockchip: rk3328: Add support for Orange Pi R1 Plus
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.

This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.

The device tree and description are taken from kernel v6.3-rc1.

Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
2023-07-28 18:45:02 +08:00
Nishanth Menon
f40f54bfed arm: dts: Fix build of am62a7 dtbs
am62a7 should be built with CONFIG_SOC_K3_AM62A7 not CONFIG_SOC_K3_AM625

Fixes: 6bdfa69155 ("arm: dts: introduce am62a7 u-boot dtbs")
Cc: Bryan Brattlof <bb@ti.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
2023-07-21 15:32:12 -04:00
Ashok Reddy Soma
37688da586 xilinx: versal-net: Add mini eMMC 5.1 configuration
Add support for Versal NET mini eMMC 5.1 configuration. Add device tree
and defconfig.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-4-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2023-07-21 09:00:38 +02:00
Ashok Reddy Soma
38e0fc06b2 xilinx: versal-net: Add mini ospi configuration
Add support for Versal NET mini Octal SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Octal SPI
related settings are enabled.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2023-07-21 09:00:38 +02:00
Ashok Reddy Soma
96683d3436 xilinx: versal-net: Add mini qspi configuration
Add support for Versal NET mini Quad SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Quad SPI
related settings are enabled.

Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
2023-07-21 09:00:38 +02:00
Tom Rini
c990ecba4d Merge https://gitlab.denx.de/u-boot/custodians/u-boot-marvell
- mvebu: Thecus: Misc enhancement and cleanup (Tony)
- mvebu: Add AC5X Allied Telesis x240 board support incl NAND
  controller enhancements for this SoC (Chris)
2023-07-13 20:38:50 -04:00
Chris Packham
4c97c4b590 arm: mvebu: Add Allied Telesis x240 board
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
2023-07-13 15:53:57 +02:00
Tim Harvey
48c6f9777c board: gateworks: venice: add imx8mp-gw7905-2x support
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.

The GW702x SOM contains the following:
 - i.MX8M Plus SoC
 - LPDDR4 memory
 - eMMC Boot device
 - Gateworks System Controller (GSC) with integrated EEPROM, button
   controller, and ADC's
 - PMIC
 - SOM connector providing:
  - eQoS GbE MII
  - 1x SPI
  - 2x I2C
  - 4x UART
  - 2x USB 3.0
  - 1x PCI
  - 1x SDIO (4-bit 3.3V)
  - 1x SDIO (4-bit 3.3V/1.8V)
  - GPIO

The GW7905 Baseboard contains the following:
 - GPS
 - microSD
 - off-board I/O connector with I2C, SPI, GPIO
 - EERPOM
 - PCIe clock generator
 - 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
 - 1x half-length miniPCIe socket with USB2.0 and USB3.0
 - USB 3.0 HUB
 - USB Type-C with USB PD Sink capability and peripheral support
 - USB Type-C with USB 3.0 host support

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2023-07-11 14:40:05 +02:00
Svyatoslav Ryhel
bdf9dead86 board: htc: endeavoru: add One X support
The HTC One X is a touchscreen-based, slate-sized smartphone
designed and manufactured by HTC that runs the Android operating
system. The One X features a 4.7" display, an Nvidia Tegra 3
quad-core chip, 1 GB of RAM and non-extendable 32 GB of internal
storage. UART-A is default debug port.

Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com>
Tested-by: Ion Agorria <ion@agorria.com>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2023-06-30 15:20:37 +02:00
Svyatoslav Ryhel
623a8c812e board: lg: x3: add Optimus 4X HD and Optimus Vu support
LG X3 is a development board based on Nvidia Tegra 3 SoC
on base of which Optimus 4X HD and Optimus Vu were created.
Both smartphones feature a 4.7" and 5" panels respectively,
an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 16/32 GB
of internal storage. Optimux 4X HD additionally has a micro
SD slot.

Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2023-06-30 15:20:37 +02:00
Svyatoslav Ryhel
855ffdfa65 board: asus: grouper: add Google Nexus 7 (2012) support
Nexus 7 is a mini tablet computer co-developed by Google and Asus
that runs the Android operating system. The Nexus 7 features a 7"
display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 8/16 GB
of internal storage.

This patch brings support for all 3 known ASUS/Google devices:
- Nexus 7 (2012) E1565
- Nexus 7 (2012) PM269
- Nexus 7 (2012) 3G - tilapia

Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS Grouper E1565
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2023-06-30 15:20:37 +02:00
Svyatoslav Ryhel
15be9a7b3b board: asus: transformer: add ASUS Transformer T30 family support
The ASUS Transformer T30 family are 2-in-1 detachable tablets
and AiO developed by ASUS that run the Android operating system
(TF600T runs Windows RT and P1801-T runs Android and Windows).
The T30 Transformers feature a 10.1-inch display (apart P1801-T),
an Nvidia Tegra 3 quad-core chip, 1/2 GB of RAM, and 16/32 GB of
storage. Transformers board derives from Nvidia Cardhu development
board.

This patch brings support for 7 known Transformer devices:
- ASUS Transformer Prime TF201
- ASUS Transformer Pad TF300T/TF300TG/TF300TL
- ASUS VivoTab RT TF600T (Windows RT based)
- ASUS Transformer Infinity TF700T
- ASUS Portable AiO P1801-T

Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # all devices
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
2023-06-30 15:20:37 +02:00
Ferass El Hafidi
deff94a15e arm: dts: add support for Videostrong KII Pro
Import the device tree from mainline linux (v6.4-rc1) and add the
old PHY reset bindings in the PHY node, else U-Boot and linux won't
be able to use the PHY.

Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
Link: https://lore.kernel.org/r/20230507124109.31778-2-vitali64pmemail@protonmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
2023-06-28 10:05:34 +02:00
Igor Prusov
aacf821bf0 ARM: dts: sync meson-a1-ad401 from Linux 6.3-rc7
Add meson-a1-ad401.dts file from Linux 6.3-rc7

Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230505125639.3605-3-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
2023-06-28 10:05:34 +02:00
Tom Rini
260d4962e0 Merge tag v2023.07-rc4 into next
Signed-off-by: Tom Rini <trini@konsulko.com>
2023-06-12 14:55:33 -04:00
Valentine Barshak
ed2f65f010 ARM: renesas: Add R8A77980 V3HSK board and CPLD code
Add board code for the R8A77980 V3HSK board.
Add CPLD sysreset driver to the R-Car V3H SK board.
Extracted from a larger patch by Valentine Barshak.

Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3H Condor, squash CPLD driver in]
2023-06-08 22:26:52 +02:00
Valentine Barshak
5f4e26964c ARM: renesas: Add R8A77970 V3MSK board and CPLD code
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.

Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
2023-06-08 22:26:52 +02:00
Tom Rini
41e289bb1f arm: Remove ti816x_evm board and ti816x SoC support
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.

Signed-off-by: Tom Rini <trini@konsulko.com>
2023-05-31 10:11:46 -04:00
FUKAUMI Naoki
74f162a1ea arm: dts: rk356x: Makefile: sort
sort alphanumerically.

Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-05-09 22:50:01 +08:00
FUKAUMI Naoki
71a95e2efd arm: dts: rockchip: add Radxa ROCK 4C+
Linux commit 246450344dad arm64: dts: rockchip: rk3399: Radxa ROCK 4C+

Add support for Radxa ROCK 4C+ SBC.

Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec

Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.

Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-05-09 22:50:01 +08:00
FUKAUMI Naoki
d0e62eeda8 arm: dts: rockchip: rock-pi-4: sync with Linux 6.3
sync dts{,i} files for Radxa ROCK Pi 4 series with Linux 6.3.

because rk3399-rock-pi-4a.dts is enough for ROCK Pi 4A/B/A+/B+ and ROCK
4SE, delete dts{,i} for ROCK Pi 4B.

Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-05-09 20:30:12 +08:00
Tianling Shen
7000a60947 rockchip: rk3328: Add support for FriendlyARM NanoPi R2C
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.

The device tree is taken from the kernel linux-next branch:
https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=004589ff9df5b75672a78b6c3c4cba93202b14c9

Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-05-09 18:58:25 +08:00
Chris Morgan
6cf6fe2537 board: rockchip: add Anbernic RGXX3 Series Devices
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:

 - Anbernic RG353M
 - Anbernic RG353P
 - Anbernic RG353V
 - Anbernic RG353VS
 - Anbernic RG503

The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.

Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.

The common specifications for each device are:

 - Rockchip RK3566 SoC
 - 2 external SDMMC slots
 - 1 USB-C host port, 1 USB-C peripheral port
 - 1 mini-HDMI output
 - MIPI-DSI based display panel
 - ADC controlled joysticks with a GPIO mux
 - GPIO buttons
 - A PWM controlled vibrator
 - An ADC controlled button

All of the common features are defined in the devicetree synced from
upstream Linux.

TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).

Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
2023-05-06 17:45:05 +08:00