These will now be detected at runtime, allowing a single U-boot
configuration to function correctly with different bitstreams. Without
this you may need to re-configure, re-build and re-flash U-boot to your
Malta if you flash a new bitstream with a different cache configuration
to your old bitstream.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This model of the pcnet is used in current Malta boards, at least in the
Malta-R rev 3. Enable support for it.
The Malta also has the ethernet controller PROM containing its MAC
address, so enable support for that in order to read that MAC address.
DHCP is a very useful feature to have available for many networks,
enable support for it also.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch adds support for running on Malta boards using coreFPGA6
core cards, including support for the msc01 system controller used
with them. The system controller is detected at runtime allowing one
U-boot binary to run on a Malta with either.
Due to the PCI I/O base differing between Maltas using gt64120 & msc01
system controllers, the UART setup is modified slightly. A second UART
is added so that there is one pointing at the correct address for each
system controller. The Malta board then defines its own
default_serial_console function to select the correct one at runtime.
The incorrect UART will simply not function.
Tested on:
- A coreFPGA6 Malta running interAptiv and proAptiv bitstreams, both
with and without an L2 cache.
- QEMU.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This is in preparation for adapting this board to function correctly on
a physical MIPS Malta board. The board is moved into an "imgtec" vendor
directory at the same time in order to ready us for any other boards
supported by Imagination in the future.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
This patch simply #ifdef's out the C-specific parts of pci.h when it is
included by an assembly file. This will allow the macros it contains to
be used from assembly source as will be done in a followup commit adding
support for more modern MIPS Malta boards.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Linux Kernel abolished include/linux/config.h long time ago.
(around version v2.6.18..v2.6.19)
We don't need to provide Linux copatibility any more.
This commit deletes include/linux/config.h
and fixes source files not to include this.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
add the possibility to set the iSerialNumber board specific.
Default value for iSerialNumber is 0x0. This value can
changed board specific through the new function
g_dnl_set_serialnumber() which must be called from the
board specific function g_dnl_bind_fixup().
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
This patch allows exiting from UMS mode to u-boot prompt
by detaching usb cable or by pressing ctrl+c.
Add new config: CONFIG_USB_CABLE_CHECK. If defined then board
file should provide function: usb_cable_connected() (include/usb.h)
that return 1 if cable is connected and 0 otherwise.
Changes v2:
- add a note to the README
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
UMS init was implemented in trats board file but mostly it comprises
common code. Due to that it has been moved to common/ums.c to avoid
code duplication in the future.
Changes:
- move ums initialization code from trats to common/ums.c
- remove unused CONFIG_USB_GADGET_MASS_STORAGE from trats.h
Changes v2:
- move this patch at the top of code cleanups patches
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Minkyu Kang <mk7.kang@samsung.com>
This patch prevents:
- ums disk capacity miscalculation because of integer overflow
Changes v2:
- Prevents passing zero size disk capacity to ums gadget driver
- Change function ums_get_capacity() to ums_disk_init() and do ums disk
initialization before gadget init
- Remove unnecessary code from mass storage driver
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marex@denx.de>
This patch introduces some cleanups to ums code. Changes:
ums common:
- introduce UMS_START_SECTOR and UMS_NUM_SECTORS as defined in
usb_mass_storage.h both default values as 0 if board config
doesn't define them
common cleanup changes:
- change name of struct "ums_board_info" to "ums"
- "ums_device" fields are moved to struct ums and "dev_num" is removed
- change function name: board_ums_init to ums_init
- remove "extern" prefixes from usb_mass_storage.h
cmd_usb_mass_storage:
- change error() to printf() if need to print info message
- change return values to command_ret_t type at ums command code
- add command usage string
Changes v2:
ums common:
- always returns number of read/write sectors
- coding style clean-up
ums gadget:
- calculate amount of read/write from device returned value.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Commit 1b0757e deleted the EP88x entry from boards.cfg file.
But it missed to remove include/configs/EP88x.h and board/ep88x/.
This commit removes them and adds EP88x to README.scrapyard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
The malloc space is to small to boot, the current uboot 2013.10-rcX,
This will fix the startup problems by increasing the mallog space to 4MiB.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Since more functions are enabled, the eb_cpux9k2_ram target does not boot.
This patch changed the TEXT_BASE, that the code fits between TEXT_BASE and ram end.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Get rid of too many ifdeffery in usb ohci driver
Add following two configuration for USB clock selecting
- CONFIG_USB_ATMEL_CLK_SEL_PLLB: using PLLB as usb ohci input clock
- CONFIG_USB_ATMEL_CLK_SEL_UPLL: using UPLL as usb ohci input clock
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add usb host support for at91sam9n12ek board.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Many platforms duplicate pretty much the same timer code yet they all have
a 32-bit freerunning counter register. Create a common implementation that
minimally requires 2 or 3 defines to add timer support:
CONFIG_SYS_TIMER_RATE - Clock rate of the timer counter
CONFIG_SYS_TIMER_COUNTER - Address of 32-bit counter
CONFIG_SYS_TIMER_COUNTS_DOWN - Define if counter counts down
All functions are weak or ifdef'ed so they can still be overriden by any
platform.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
The definitions for CONFIG_SYS_PROMPT are varied with little reason other
than to display the board name. Over half the definitions are "==> ", so
make this the default. The rest of the boards remain unchanged to avoid
breaking any external scripts expecting a certain prompt.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This reverts commit 178b8e15ad.
Patch was merged too fast, without checking that another patch
is fixing the reported issue globally - reverted.
Signed-off--by: Stefano Babic <sbabic@denx.de>
rdaddr was missing which is a common location for loading ramdisks to.
loadaddr was higher than it needs to be, so use the same value other TI
platforms use.
Signed-off-by: Tom Rini <trini@ti.com>
Turn on GPIO commands for cm-t35 and cm-t3730.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Current default bootdelay of 10 seconds is too long.
Reduce default bootdelay to 3 seconds.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
UART booting is supported on this SoC, but via UART3 rather than UART1.
Because of this we must change the board to use UART3 for all console
access (only one UART is exposed on this board and a slight HW mod is
required to switch UARTs).
Signed-off-by: Minal Shah <minal.shah@ti.com>
[trini: Make apply to mainline, reword commit]
Signed-off-by: Tom Rini <trini@ti.com>
With changes to increase the size of the device tree (required to move
more data out of the kernel and into DT), loading the args at the old
address leads to us overwriting things later on. To correct this, load
the args file to where we load the device tree anyhow. This is also
safe for non-DT booting as in either case we use r2 to pass in the
location of things.
Signed-off-by: Tom Rini <trini@ti.com>
Increase the tested memory region for mtest and define
CONFIG_SYS_MEMTEST_SCRATCH for CONFIG_SYS_ALT_MEMTEST
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Silent u-boot and no bootdelay
Signed-off-by: Thomas Weber <thomas.weber@corscience.de>
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
The new tricordereeprom command can read and write the eeprom for hardware
detection on tricorder devices.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
Before we always ran 'mtdparts default' which also set the mtdparts and mtdids
environment. But if we changed that values by intention we will overwrite
them with our default values. This is obviously bad!
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
The new flash layout respects posible bad blocks in sectors reserved for e.g.
SPL, u-boot, kernel, env a.s.o.
Additionally this patch prepares for U-Boot Falcon mode for boot time saving.
Signed-off-by: Andreas Bießmann <andreas.biessmann@corscience.de>
- switch to correct ecc layout used by the RBL
enable CONFIG_NAND_6BYTES_OOB_FREE_10BYTES_ECC
- update default environment
- change A2CR to correct value for UART boot mode
- adapt cs3cfg timings for nand
- change LED bootmode signalization
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.
Since the IGEPv2 board and the IGEP COM Module use a TI
OMAP35xx/DM37xx processor, is better to rename its board
config to use this naming scheme.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
There seems to be a naming convention for the configuration
files for boards using the same SoC family. This makes
easier to do changes that affect different boards based
on the same SoC.
Since the IGEP COM AQUILA use a TI AM335x processor is better
to rename its board config to use this naming scheme.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Enable the bootcount driver for am335x in general. We leave adding a
bootlimit and altbootcmd to the environment to the board ports.
Signed-off-by: Tom Rini <trini@ti.com>
There is no real benefit in adding the board name into U-boot's prompt.
Use the simple "=> " prompt across FSL boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
T4240QDS eSDHC host capabilities reigster should have VS33 bit define.
Add quirk CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 to deal with capacity
missing
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
SMDK5420 has a new Security Management Unit added
for dwmmc driver, hence, configuring the control
registers to support booting via eMMC.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
To prevent the confusion, use the get_mmc_clk() instead of mmc_clk().
get_mmc_clk() is more exactly name.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
EXT_CSD_ERASE_GROUP_DEF is lost every time after a reset or
power off. Set it if device has enhanced partitions.
Signed-off-by: Oliver Metz <oliver@freetz.org>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
make CONSOLE_BG_COL/CONSOLE_FG_COL configurable through board config file.
Clear video screen in video_init().
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
This patch introduces the support for Keymile's kmp204x reference
design. This design is based on Freescale's P2040/P2041 SoC.
The peripherals used by this design are:
- DDR3 RAM with SPD support
- SPI NOR Flash as boot medium
- NAND Flash
- 2 PCIe busses (hosts 1 and 3)
- 3 FMAN Ethernet devices (FMAN1 DTSEC1/2/5)
- 3 Local Bus windows, with one dedicated to the QRIO reset/power mgmt
FPGA
- 2 HW I2C busses
- last but not least, the mandatory serial port
The board/keymile/kmp204x code is mostly based on Freescale's P2041rdb
support and was changed according to our design (that means essentially
removing what is not present on the designs and a few adaptations).
There is currently only one prototype board that is based on this design
and this patch also introduces it. The board is called kmlion1.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
kmp204x: update the ENV #define
The comments had to be refined as well as the total size
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix ddr.c]
Acked-by: York Sun <yorksun@freescale.com>
This can be useful if one wants to disable an interface in u-boot
because u-boot should not manage it but then later reenable it for FDT
fixing or if the kernel uses this interface.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
[York Sun: fix conflict in fm_eth.h]
Acked-by: York Sun <yorksun@freescale.com>
This must be defined by a board support file that want to use the
keymile common.c board_eth_init function that requires ethernet_present
to be defined.
Currently all the km architectures use it but the kmp204x architecture
later supported in this series does use another board_eth_init function
and thus does not define it.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This must be defined for all the keymile boards that use the common
i2c_abort function that is used to "reset" the I2C bus. These are
currently km82xx and km_arm boards.
The km83xx boards use other functions and thus do not need this.
This patch removes the CONFIG_SYS_I2C_INIT_BOARD from keymile-common.h
and defines it for km_arm.h and km82xx.h.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The ip kernel parameter had a typo in it (we've been lucky that it has
worked until now).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
It must be set to a different value for the later add kmp204x
architecture, because we are restricted to 1MB SRAM.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Introduce different macros for storing addresses of multiple
USB controllers. This is required for successful initialization
and usage of multiple USB controllers inside u-boot
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
c29xpcie REV_A board DDR ECC chip has bad impedance in hardware,
force that kind of board to be DDR ECC off when booting.
Other version board config ECC on/off by hwconfig=fsl_ddr:ecc=on
in uboot enviroment.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This changes clock definition of SCIF from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_SCIF_CLK_FREQ, and clock definition of TMU from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_TMU_CLK_FREQ,
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Move defines only needed by mv_udc.c to a file
in the same directory.
This allows usbtty to compile for mv_udc,
but it still doesn't link.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Previously, only host1 was supported using an index of 0.
Now, otg has index 0, host1 is 1, host2 is 2, host3 is 3.
Since OTG requires usbmode to be set after reset, I added
CONFIG_EHCI_HCD_INIT_AFTER_RESET to nitrogen6x.h and
mx6qsabreauto.h.
I also added a weak function board_ehci_power to handle
turning power on/off for otg.
Type is type of device connected (USB stick vs Host.)
Init is type of device desired.
Only power up port if type == init == USB_INIT_HOST.
Only return error if type != init.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This will be used by usb_lowlevel_init so it will
no longer be used by only board specific functions.
Move definition of enum usb_init_type higher in file
so that it will be available for usb_low_level_init.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add the support for the am437x xhci usb host.
The xHCI host on AM437 is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.
The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Moving the usb/phy code from xhci-omap to the usb/phy directory
and moving the associated phy code over to the new file.
Newer TI processors adding xHCI support will have different PHY configurations
so therefore abstracting this code away will prevent messing around with the
xhci-omap file itself.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
A set of environment variables needs to be updated to provide support for
TIZEN download command (tizendown).
Since DFU is used as a flashing backend, it is also necessary to extent
malloc pool size for DFU buffer allocation.
Moreover, for compatibility reasons (Win vs. Lin) new USB idProduct number
for download gadget had to be added.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Implementation of USB download function which supports THOR protocol.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
New parameter, namely *name has been added to g_dnl_bind_fixup().
It is necessary (for compatibility reasons) to assign new USB idProduct
and idVendor for different usb functions.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Define the dfu_get_buf() and dfu_free_buf() as global functions.
They are necessary for zero copy buffer management, when DFU backend is
used for storing data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
New function - dfu_get_alt() - has been added to dfu core. If present, it
returns alt setting's number corresponding to passed name.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
This commit unifies board-specific USB initialization implementations
under one symbol (usb_board_init), declaration of which is available in
usb.h.
New API allows selective initialization of USB controllers whenever needed.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Add new functionality to turn on SMPS10 regulator.
This supplies the VBUS to devices connected to the
USB host ports
Signed-off-by: Dan Murphy <dmurphy@ti.com>
This enables support for xHCI host controller on Exynos5
and further disables EHCI support, to make sure only one
host controller is enabled at a time, since right now
using two controllers at a time is not possible with
current usb core infrastructure.
Anyone who wants to enable EHCI support again needs to
enable CONFIG_USB_EHCI, CONFIG_USB_EHCI_EXYNOS once again
in exynos5-dt config.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
XHCI stack driver needs this to align buffers to
CacheLine boundary. So define the same to be '64'
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Adding required compatible string for xHCI host controller
as well as USB 3.0 PHY to enable dt support for usb 3.0 on
exynos5.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds driver layer for xHCI controller in Samsung's
exynos5 soc. This interacts with xHCI host controller stack.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
This board supports FEC Ethernet, SPI NOR and NAND flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Christoph Baumann <c.baumann@ppc-ag.de>
Add basic support for mx6q udoo board.
For further information about Udoo board:
http://www.udoo.org/
Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
(Interface is not quite the same as Phillips PCA9547.)
Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
This changes clock definition of SCIF from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_SCIF_CLK_FREQ, and clock definition of TMU from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_TMU_CLK_FREQ for boards.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
The former SH/TMU driver had calculated timer based on CONFIG_SYS_CLK_FREQ.
The newest SH/TMU newly needs calculation of the clock for TMU.
This patch defines clock CONFIG_SH_TMU_CLK_FREQ for TMU and changes it to
CONFIG_SH_TMU_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Previously, the address of a requested capability is define like that
"#define PCI_DCR 0x78"
But, the addresses of capabilities is different with regard to PCIe revs.
So this method is not flexible.
Now a function to get the address of a requested capability is added and used.
It can get the address dynamically by capability ID.
The step of this function:
1. Read Status register in PCIe configuration space to confirm that
Capabilities List is valid.
2. Find the address of Capabilities Pointer Register.
3. Find the address of requested capability from the first capability.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.
For more details, see board/freescale/p1010rdb/README.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>
Since pins multiplexing, SDHC shares signals with IFC, with this patch:
To enable SDHC in case of NOR/NAND/SPI boot
a) For temporary use case in runtime without reboot system
run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
b) For long-term use case
set 'esdhc' in hwconfig and save it.
To enable IFC in case of SD boot
a) For temporary use case in runtime without reboot system
run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
b) For long-term use case
set 'ifc' in hwconfig and save it.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl
Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which
uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a
pbl boot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For USB device-tree fix-up to work properly, its necessary to
mention USB1 options before that of USB2 inside default hwconfig
string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Current IFC timings for NAND flash are not able to support existing
K9F1G08U0B and new K9F1G08U0D flash.
so Update the timings to support both.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.
QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
1. Confirm whether QSGMII Riser Card is used.
2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.
However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
This patch re-config the NOR flash timing parameters which could make
the ifc timing more flexible for NOR flash.
The new parameters could fix the problem of hanging at "Flash:"
occasionally when booting the board.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
This patch is for board config file not to add CONFIG_SECURE_BOOT
condition for include the asm/fsl_secure_boot.h.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
OMAP5 boards may have both eMMC (on MMC2) and an SD slot (on MMC1). We
Update the default bootcmd to match what happens on AM335x where we try
SD first, and then eMMC. In this case however, the hardware layout used
for powering both of these means that in the kernel eMMC shall be found
first as it is powered by a fixed regulator and SD found second as SD is
powered via the palmas which will result in deferred probing.
Tested-by: Aparna Balasubramanian <aparnab@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This matches the 64 bit size in struct mtd_info and allows the mtdparts
command to function correctly with a flash >= 4GiB. Format specifiers
for size & offset are given the ll length, matching its use in
drivers/mtd in absence of something like inttypes.h/PRIx64.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
Linux modified the MTD driver interface in commit edbc4540 (with the
same name as this commit). The effect is that calls to mtd_read will
not return -EUCLEAN if the number of ECC-corrected bit errors is below
a certain threshold, which defaults to the strength of the ECC. This
allows -EUCLEAN to stop indicating "some bits were corrected" and begin
indicating "a large number of bits were corrected, the data held in
this region of flash may be lost soon". UBI makes use of this and when
-EUCLEAN is returned from mtd_read it will move data to another block
of flash. Without adopting this interface change UBI on U-boot attempts
to move data between blocks every time a single bit is corrected using
the ECC, which is a very common occurance on some devices.
For some devices where bit errors are common enough, UBI can get stuck
constantly moving data around because each block it attempts to use has
a single bit error. This condition is hit when wear_leveling_worker
attempts to move data from one PEB to another in response to an
-EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is
called to perform the data copy, and after the data is written it is
read back to check its validity. If that read returns UBI_IO_BITFLIPS
(in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to
wear_leveling worker, which then proceeds to schedule the destination
PEB for erasure. This leads to erase_worker running on the PEB, and
following a successful erase wear_leveling_worker is called which
begins this whole cycle all over again. The end result is that (without
UBI debug output enabled) the boot appears to simply hang whilst in
reality U-boot busily works away at destroying a block of the NAND
flash. Debug output from this situation:
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027
UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096
UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083
UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data
UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192
UBI: fixable bit-flip detected at PEB 1027
UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192
UBI: fixable bit-flip detected at PEB 4083
UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0
UBI DBG: erase_worker: erase PEB 4083 EC 55
UBI DBG: sync_erase: erase PEB 4083, old EC 55
UBI DBG: do_sync_erase: erase PEB 4083
UBI DBG: sync_erase: erased PEB 4083, new EC 56
UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
...
This patch adopts the interface change as in Linux commit edbc4540 in
order to avoid such situations. Given that none of the drivers under
drivers/mtd return -EUCLEAN, this should only affect those using
software ECC. I have tested that it works on a board which is
currently out of tree, but which I hope to be able to begin
upstreaming soon.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
Upon further inspection and review and chatting with kernel folks, what
happens here is that what mmcblk# a device gets is based on probe order.
So a system with an SD card inserted with place eMMC on mmcblk1, but
without an SD card, it will be on mmcblk0. So U-boot can only provide a
best guess. In this case, if no SD card is present, we would want to
pass mmcblk0p2 still. If an SD card is present, it woudl be able to
provide a uEnv.txt that would be loaded (even if the kernel is NOT
there) which can still update mmcroot variable.
This reverts commit 827512fb11.
Cc: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Tom Rini <trini@ti.com>
This function, if implemented by the board, provides a microsecond
timer. The granularity may be larger than 1us if hardware does not
support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari S Shinde <rajeshwari.s@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
As documented, almost all U-Boot commands expect numbers to be entered
in hexadecimal input format. (Exception: for historical reasons, the
"sleep" command takes its argument in decimal input format.)
This rule was broken for the "load" command; for details please see
especially commits 045fa1e "fs: add filesystem switch libary,
implement ls and fsload commands" and 3f83c87 "fs: fix number base
behaviour change in fatload/ext*load". In the result, the load
command would always require an explicit "0x" prefix for regular
(i. e. base 16 formatted) input.
Change this to use the standard notation of base 16 input format.
While strictly speaking this is a change of the user interface, we
hope that it will not cause trouble. Stephen Warren comments (see
[1]):
I suppose you can change the behaviour if you want; anyone
writing "0x..." for their values presumably won't be
affected, and if people really do assume all values in U-Boot
are in hex, presumably nobody currently relies upon using
non-prefixed values with the generic load command, since it
doesn't work like that right now.
[1] http://article.gmane.org/gmane.comp.boot-loaders.u-boot/171172
Acked-by: Tom Rini <trini@ti.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Adding System Manager driver which will configure the
pin mux for real hardware Cyclone V development kit
(not Virtual Platform)
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Acked-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
omap1510inn is orphan and has been for years now.
Reove it and, as it was the only arm925t target,
also remove arm925t support.
Update doc/README.scrapyard accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Qspi controller can have a memory mapped port which can be used for
data read. Added support to enable memory mapped port read.
This patch enables the following:
- It enables exchange of memory map address between mtd and qspi
through the introduction of "memory_map" flag.
- Add support to communicate to the driver that memory mapped
transfer is to be started through introduction of new flags like
"SPI_XFER_MEM_MAP" and "SPI_XFER_MEM_MAP_END".
This will enable the spi controller to do memory mapped configurations
if required.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Compared to other spi flashes, ramtron has a different
probing and implementation on flash ops, hence moved
ramtron probe code into ramtron driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
From Micron, 512MB onwards, flash requires to poll flag status
instead of read status- hence added E_FSR flag on spectific
flash parts.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
SECT_4K, SECT_32K and SECT_64K opeartions are performed to
to specific flash by adding a SECT* flag on respective
spi_flash_params.flag param.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Most of the SST flashes needs to write up using SST_WP, AAI
Word Program, so added a flag param on spi_flash_params table.
SST flashes, which supports SST_WP need to use a WP write
sst_write_wp instead of common flash write.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
The modelist data uses the list definition but the 'list.h' header
were not being included. The build failure is bellow:
,----
| In file included from yyyy.c:16:0:
| .../u-boot/include/linux/fb.h:503:19: error: field 'modelist' has incomplete type
| struct list_head modelist; /* mode list */
| ^
| make[1]: *** [yyyy.o] Error 1
| make[1]: Leaving directory `.../u-boot/board/xxx/yyyy'
| make: *** [board/xxx/yyyy/libyyyy.o] Error 2
`----
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
To enable hypervisors utilizing the ARMv7 virtualization extension
on the Versatile Express board with the A15 core tile, we add the
required configuration variable.
Also we define the board specific smp_set_cpu_boot_addr() function to
set the start address for secondary cores in the VExpress specific
manner.
There is no need to provide a custom smp_waitloop() function here.
This also serves as an example for what to do when adding support for
new boards.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
Currently the non-secure switch is only done for the boot processor.
To enable full SMP support, we have to switch all secondary cores
into non-secure state also.
So we add an entry point for secondary CPUs coming out of low-power
state and make sure we put them into WFI again after having switched
to non-secure state.
For this we acknowledge and EOI the wake-up IPI, then go into WFI.
Once being kicked out of it later, we sanity check that the start
address has actually been changed (since another attempt to switch
to non-secure would block the core) and jump to the new address.
The actual CPU kick is done by sending an inter-processor interrupt
via the GIC to all CPU interfaces except the requesting processor.
The secondary cores will then setup their respective GIC CPU
interface.
While this approach is pretty universal across several ARMv7 boards,
we make this function weak in case someone needs to tweak this for
a specific board.
The way of setting the secondary's start address is board specific,
but mostly different only in the actual SMP pen address, so we also
provide a weak default implementation and just depend on the proper
address to be set in the config file.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
While actually switching to non-secure state is one thing, another
part of this process is to make sure that we still have full access
to the interrupt controller (GIC).
The GIC is fully aware of secure vs. non-secure state, some
registers are banked, others may be configured to be accessible from
secure state only.
To be as generic as possible, we get the GIC memory mapped address
based on the PERIPHBASE value in the CBAR register. Since this
register is not architecturally defined, we check the MIDR before to
be from an A15 or A7.
For CPUs not having the CBAR or boards with wrong information herein
we allow providing the base address as a configuration variable.
Now that we know the GIC address, we:
a) allow private interrupts to be delivered to the core
(GICD_IGROUPR0 = 0xFFFFFFFF)
b) enable the CPU interface (GICC_CTLR[0] = 1)
c) set the priority filter to allow non-secure interrupts
(GICC_PMR = 0xFF)
Also we allow access to all coprocessor interfaces from non-secure
state by writing the appropriate bits in the NSACR register.
The generic timer base frequency register is only accessible from
secure state, so we have to program it now. Actually this should be
done from primary firmware before, but some boards seems to omit
this, so if needed we do this here with a board specific value.
The Versatile Express board does not need this, so we remove the
frequency from the configuration file here.
After having switched to non-secure state, we also enable the
non-secure GIC CPU interface, since this register is banked.
Since we need to call this routine also directly from the smp_pen
later (where we don't have any stack), we can only use caller saved
registers r0-r3 and r12 to not mess with the compiler.
Signed-off-by: Andre Przywara <andre.przywara@linaro.org>
This patch add support for a new Samsung board Trats2.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch add support for new multi function pmic max77693.
The driver is split into three modules: pmic, muic and fuelgage.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The download gadget code and DFU function lacks of proper declarations
for the case when a target board wants to use only one of available usb
functions.
Moreover the relevant declarations have been moved to consistent
localization (like <dfu.h>).
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Only the <linux/usb/gadget.h> requires error.h include. Hence, several
includes of error.h at USB gadget functions are not needed.
Moreover unnecessary malloc.h includes were also removed.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
The mass storage composite function is now compiled in only when
CONFIG_USB_GADGET_MASS_STORAGE is defined.
Such change provides binary size reduction for boards which use USB
download gadget (like am335x_evm) with DFU, but don't use UMS.
For example at am335x_evm board reduction is more than 2KiB for
text and around 120B for data.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Marek Vasut <marex@denx.de>
DFU spec mentions it as a method to upgrade firmware (software stored
in writable non-volatile memory). It also says other potential uses of
DFU is beyond scope of the spec.
Here such a beyond the scope use is being attempted - directly pumping
binary images from host via USB to RAM. This facility is a developer
centric one in that it gives advantage over upgrading non-volatile
memory for testing new images every time during development and/or
testing.
Directly putting image onto RAM would speed up upgrade process. This and
convenience was the initial thoughts that led to doing this, speed
improvement over MMC was only 1 second though - 6 sec on RAM as opposed
to 7 sec on MMC in beagle bone, perhaps enabling cache and/or optimizing
DFU framework to avoid multiple copy for ram (if worth) may help, and
on other platforms and other boot media like NAND maybe improvement
would be higher.
And for a platform that doesn't yet have proper DFU suppport for
non-volatile media's, DFU to RAM can be used.
Another minor advantage would be to increase life of mmc/nand as it
would be less used during development/testing.
usage: <image name> ram <start address> <size>
eg. kernel ram 0x81000000 0x1000000
Downloading images to RAM using DFU is not something new, this is
acheived in openmoko also.
DFU on RAM can be used for extracting RAM contents to host using dfu
upload. Perhaps this can be extended to io for squeezing out register
dump through usb, if it is worth.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Gerhard Sittig <gsi@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Heiko Schocher <hs@denx.de>
MMC and NAND independently defines same enumerators for read/write.
Unify them by defining enum in dfu header. RAM support that is being
added newly also can make use of it.
Signed-off-by: Afzal Mohammed <afzal.mohd.ma@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
New dfu_init_env_entities() function has been extracted from cmd_dfu.c and
stored at dfu core.
This is a dfu centric code, so it shall be processed in the core.
Change-Id: I756c5de922fa31399d8804eaadc004ee98844ec2
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Heiko Schocher <hs@denx.de>
Add atmel usba udc driver support, porting from Linux kernel
The original code in Linux Kernel information is as following
commit e01ee9f509a927158f670408b41127d4166db1c7
Author: Jingoo Han <jg1.han@samsung.com>
Date: Tue Jul 30 17:00:51 2013 +0900
usb: gadget: use dev_get_platdata()
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Up till now the DFU maximum file size (to be written to e.g. eMMC)
was different from the DFU data buffer size. It caused errors when
one buffer was smaller than data to be written.
Now, the maximum DFU file size is equal to default DFU buffer size.
In spite of this, user is still able to manually adjust those default
values.
Change-Id: Ied75d0f7b59588ebd79dae9a22af801d36622216
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
If, in CONFIG_BOOTCOMMAND, the environment switches both the mmcdev
and bootpart variables to refer to MMC device 1, it would make sense
that the mmcroot env variable should switch to that device as well.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
dra7xx_evm has eMMC and the default environment can be stored in it.
So enabling saveenv command and the configs to store environment in eMMC.
Tested on DRA752 ES1.0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
In Errata 1.0.24, if the board is running at OPP50 and has a warm reset,
the boot ROM sets the frequencies for OPP100. This patch attempts to
drop the frequencies back to OPP50 as soon as possible in the SPL. Then
later the voltages and frequencies up set higher.
Cc: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Adapt to current framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a am33xx_spl_board_init (and enable the PMICs) that we may see,
depending on the board we are running on. In all cases, we see if we
can rely on the efuse_sma register to tell us the maximum speed. In the
case of Beaglebone White, we need to make sure we are on AC power, and
are on later than rev A1, and then we can ramp up to the PG1.0 maximum
of 720Mhz. In the case of Beaglebone Black, we are either on PG2.0 that
supports 1GHz or PG2.1. As PG2.0 may or may not have efuse_sma set, we
cannot rely on this probe. In the case of the GP EVM, EVM SK and IDK we
need to rely on the efuse_sma if we are on PG2.1, and the defaults for
PG1.0/2.0.
Signed-off-by: Tom Rini <trini@ti.com>
Without those it's very easy to make mistakes when for instance
the 'size' field is more than just a constant.
Signed-off-by: Mischa Jonker <mjonker@synopsys.com>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Anton Staaf <robotboy@chromium.org>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
We need to load 'imx6dl-sabresd.dtb' in the mx6dl version.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
In arch/arm/cpu/arm1136/cpu.c we have:
#ifndef CONFIG_SYS_CACHELINE_SIZE
#define CONFIG_SYS_CACHELINE_SIZE 32
#endif
,so there is no need to define 'CONFIG_SYS_CACHELINE_SIZE' with the default
size in the board config file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The wandboard solo version should boot the 'imx6dl-wandboard.dtb' file, since
dual-lite and solo variants are the same SoC with only the number of cores being
different.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Add a driver for the TPS65910 PMIC that is found in the AM335x GP EVM,
AM335x EVM SK and others.
Signed-off-by: Philip, Avinash <avinashphilip@ti.com>
[trini: Split and rework Avinash's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
Add a driver for the TPS65217 PMIC that is found in the Beaglebone
family of boards.
Signed-off-by: Greg Guyotte <gguyotte@ti.com>
[trini: Split and rework Greg's changes into new drivers/power
framework]
Signed-off-by: Tom Rini <trini@ti.com>
The SPDX License List version 1.19 now contains an official entry for
the IBM-pibs license. However, instead of our suggestion "ibm-pibs",
the SPDX License List uses "IBM-pibs", with the following rationale:
"The reason being that all other SPDX License List short identifiers
tend towards using capital letters unless spelling a word. I'd prefer
to be consistent to this end".
Change the license IDs to use the official name.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Fix various misspellings of things like "environment", "kernel",
"default" and "volatile", and throw in a couple grammar fixes.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Since UBIFS is enabled for cpux9k2, more malloc space is needed.
For the current uboot 2013.10-rcX the size is to small, this will fix the
startup problems by increasing the malloc space to 4MiB.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
When CONFIG_MMC_SPI is not enabled, the MMC_MODE_SPI capability can
never be set. However there is code in mmc.c which uses the
mmc_host_is_spi macro to check that capability & act accordingly. If we
expand that macro to 0 when CONFIG_MMC_SPI is not set (since it will
always be 0 at runtime anyway) then the compiler can optimize away the
SPI-specific code paths in mmc.c.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Samsung SoC is supported the WIDE8, even if Controller version is v2.0.
So add the SDHCI_QUIRK_USE_WIDE8 for Samsung-SoC.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
Signed-off-by: Eric Jarrige <eric.jarrige@armadeus.org>
Signed-off-by: Nicolas Colombain <nicolas.colombain@armadeus.com>
Without this patch, SPD access will fail which leads to DDR init fail.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: York Sun <yorksun@freescale.com>
Add STMP3780-based Sansa Fuze+ board. This board is a small PMP
device sporting a CPU which was later rebranded to i.MX233 .
Currently supported is USB gadget mode and MMC .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Add STMP3780-based XFi3 board. This board is a small PMP device
sporting a CPU which was later rebranded to i.MX233 . Currently
supported is USB gadget mode and both external SD and internal
Phison SD-NAND bridge .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
LCD4 needs a slightly different GPIO configuration than the
original LWMON5 variant. GPIO49 needs to be configured to a
default output value of 0 (permanent voltage supply).
Additionally lcd4 also needs to enable the LSB transmitter.
Signed-off-by: Stefan Roese <sr@denx.de>
For most boards which define CONFIG_SPL_PAD_TO,
it is defined in config header files.
Currently, there exists only one exception, cam_enc_4xx board.
This patch moves CONFIG_SPL_PAD_TO definition
from board/ait/cam_enc_4xx/config.mk
to include/configs/cam_enc_4xx.h.
With this modification, we can delete a glue code
in the top level config.mk:
ifneq ($(CONFIG_SPL_PAD_TO),)
CPPFLAGS += -DCONFIG_SPL_PAD_TO=$(CONFIG_SPL_PAD_TO)
endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
libata already has similar functions as implemented in the ahci code.
Refactor the code to use the libata variants and remove the dependency on
ata.h. Convert some defines to use the version from libata.h. Also, remove
some unnecessary memset's of bss data.
This is a step toward hopefully merging ahci.c and dw_ahsata.c which are
essentially the same driver.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Tom Rini <trini@ti.com>
gcc allows extensions to be non compiler specific by defining
__* macros for the attributes supported by gcc. Having a
different definition causes many warnings during the build
(cdefs.h on FreeBSD uses __attribute((__pure__)) where u-boot
uses __attribute__((pure)) for example). Do not redefine
these macros to suppress these warnings.
This patch ignores the checkpatch warning:
WARNING: __packed is preferred over __attribute__((packed))
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Somewhere along the line of refactoring the am335x header files, the
kernel image load was lost, so put it back in.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Separating the configuration file for Virtual
Target and real hardware Cyclone V development kit
Signed-off-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
This adds the "test_compression" command when building the sandbox. This
tests the existing compression and decompression routines for simple
sanity and for buffer overflow conditions.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Add mkimage support for generating and verifying MXS bootstream.
The implementation here is mostly a glue code between MXSSB v0.4
and mkimage, but the long-term goal is to rectify this and merge
MXSSB with mkimage more tightly. Once this code is properly in
U-Boot, MXSSB shall be deprecated in favor of mkimage-mxsimage
support.
Note that the mxsimage generator needs libcrypto from OpenSSL, I
therefore enabled the libcrypto/libssl unconditionally.
MXSSB: http://git.denx.de/?p=mxssb.git;a=summary
The code is based on research presented at:
http://www.rockbox.org/wiki/SbFileFormat
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
This patch add new functions to pmic max77686 to set voltage and mode.
Signed-off-by: Piotr Wilczek <p.wilczek@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Arndale board is based on samsung's exynos5250 soc.
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Re-group the general options to note things that can be removed safely
to reduce binary size when not required, and expand the comment about
what commands we do include to note it could be replaced with a specific
list of required one. While at it, move the CMD parts of various
blocks IP to the end of the list for consistency.
Signed-off-by: Tom Rini <trini@ti.com>
After examining both TRMs and doing some experimentation, we can rely on
using the start of the download area for CONFIG_SPL_TEXT_BASE and then
move SRAM_SCRATCH_SPACE_ADDR up, just like am335x. This is required for
peripheral boot modes such as UART.
Signed-off-by: Tom Rini <trini@ti.com>
We only need this library when we're doing "disk" access to MMC/SD.
Update comment around the rest of CONFIG_SPL_LIB* to note that the
others are always required.
Signed-off-by: Tom Rini <trini@ti.com>
We had been allowing the max size to be larger than actually allowed by
the ROM. Expand the commentary here to explain why we set these
locations.
Signed-off-by: Tom Rini <trini@ti.com>
Now that IGEP base boards default environment use
the bootz command to boot a zImage instead of a
uImage, it makes sense to add support to supply a
raw initrd image to the kernel if needed.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Use CONFIG_MACH_TYPE generic macro to set the machine type
number in the common arm code instead of setting it in the
board code.
Signed-off-by: Oleksandr Tyshchenko <oleksandr.tyshchenko@ti.com>
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Since config.mk is deprecated, remove this file,
and move CONFIG_SYS_TEXT_BASE define to config file.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Wolfgang Denk <wd@denx.de>
With the new include structure for TI platforms, we need to not define
our own CONFIG_SYS_PROMPT and also need to include
<configs/omap5_common.h> much sooner, so do both of these. Also drop
the unused CONFIG_NET_MULTI
Signed-off-by: Tom Rini <trini@ti.com>
Update the Makefiles so that all boards can use the same spl generation tool
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
updating an ubi partition needs a completely erased mtd partition,
see:
http://lists.infradead.org/pipermail/linux-mtd/2011-May/035416.html
So, add partubi alt setting for the dfu_alt_info environment
variable to mark this partition as an ubi partition. In case we
update an ubi partition, we erase after flashing the image into the
partition, the remaining sektors.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@ti.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Add the USB ehci support for the OMAP5 uEVM.
Configure the uEVM mux data
Add the flags to build the appropriate modules
Add the usb call backs to initialize the EHCI controller
Signed-off-by: Dan Murphy <dmurphy@ti.com>
remove the config.mk file
move text base define to board config file for following boards
- at91sam9m10g45ek
- at91sam9x5ek
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
