Import cvmx-asxx-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import cvmx-agl-defs.h header file from 2013 U-Boot. It will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Import misc cvmx-helper header files from 2013 U-Boot. They will be used
by the later added drivers to support PCIe and networking on the MIPS
Octeon II / III platforms.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This will be used by the upcoming Serdes and driver code ported from
the original 2013 U-Boot code to mainline.
Signed-off-by: Stefan Roese <sr@denx.de>
Add the MMC DT node to the Octeon EBB7304 DT file including the
regulator node for the MMC power supply.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add the MMC DT node to the Octeon CN73xx dtsi file.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Until now, the Octeontx MMC driver did only support the ARM Octeon
TX/Tx2 platforms. This patch adds support for the MIPS Octeon platform
to this driver. Here a short summary of the changes:
- Enable driver compilation for MIPS Octeon, including the MMC related
header file
- Reorder header inclusion
- Switch to using the clk framework to get the input clock
- Remove some functions for MIPS Octeon, as some registers don't
exist here
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes the displayed DDR type of mt7628.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The MT7688KN is a multi-chip package with 8MiB DDR1 KGD. So the DDR type
from bootstrap register must be ignored, and always be assumed as DDR1.
This patch fixes an issue that mt7628_ddr_pad_ldo_config() may be passed
with a wrong ddr_type in MT7688KN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make sure to reset the switch core at probe time.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Move this out of the common header and include it only where needed. In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly. Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
The mt7620_rfb board supports integrated 10/100M PHYs plus two external
giga PHYs. It also has 8MB SPI-NOR, mini PCI-e x1 slot, SDHC and USB.
The mt7620_mt7530_rfb boards supports an external MT7530 giga switch and a
16MB SPI-NOR flash.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for MediaTek MT7620 SoC.
All files are dedicated for u-boot.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for mtmips SoCs to initialize the SDRAM.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The sysreset driver has a config CONFIG_SPL_SYSRESET for the spl stage.
Change CONFIG_SYSRESET to CONFIG_IS_ENABLED(SYSRESET) will give spl a
chance to use _machine_restart instead of the sysreset driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
CONFIG_SYS_SDRAM_BASE points to cached memory, i.e. KSEG0, which is not
suitable for detecting memory size.
Replace CONFIG_SYS_SDRAM_BASE with KSEG1, and make dram_init() always do
memory size detection in any stage.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently only mt7628 needs the sysreset driver, do not select it for
mt7620.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch is a preparation for add a new soc fot mtmips.
Move all mt7628 related Kconfig (boards and UART selection) into mt7628
subdirectory and make sure the top directory of mtmips contains only
selection for SoCs.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Previous the dts files for gardena-smart-gateway-mt7688 and
linkit-smart-7688 are set to be built when mtmips is selected.
This can lead to a compilation error if another soc is added to this arch
with different dtsi files.
So it's better to build the dtb only if their board is selected.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
In order to remove the arch-specific ifdefs around initr_trap, introduce
arch_initr_trap weak initcall. Implementations for ppc/m68k/mips have
been moved to arch/<arch>/lib/traps.c
Default implementation is a nop stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a tool to update or insert an Octeon specific header into the U-Boot
image. This is needed e.g. for booting via SPI NOR, eMMC and NAND.
While working on this, move enum cvmx_board_types_enum and
cvmx_board_type_to_string() to cvmx-bootloader.h and remove the
unreferenced (unsupported) board definition.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Using ram_get_info() is complicated and does not work after relocation.
Now that gd->ram_size holds the full RAM size, let's use it instead and
remove the ram_get_size logic completely.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With this patch, gd->ram_size now holds to full RAM size detected by the
DDR init code. It introduces the get_effective_memsize() function to
report the maximum usable RAM size in U-Boot to the system instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Octeon has a specific boot header, when booted via SPI NOR, NAND or MMC.
Here the only 2 instructions are allowed in the first few bytes of the
image. And these instructions need to be one branch and a nop. This
patch adds the necessary nop after the nop, to that the common MIPS
image is compatible with this Octeon header.
The tool to patch the Octeon boot header into the image will be send in
a follow-up patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Octeon needs a platform specific cmd to boot the Linux kernel, as
specific parameters need to be passed and special handling for the
multiple cores (SMP) is needed.
Co-developed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
[use gd->ram_base instead of gd->bd->bi_memstart]
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This is needed for Linux booting, as the memory infos need to be passed
in this bootmem format to the Linux kernel.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add header to handle bootinfo support, needed for Octeon Linux kernel
booting.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes the Octeon feature detection used in many Octeon
drivers.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header includes common register defines and accessor functions.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the necessary lowlevel init code, to enable SMP Linux
booting. This code will be used with the platform specific Octeon Linux
boot command "bootoctlinux", which starts a configurable number of cores
into Linux.
Additionally some erratas and lowlevel register initializations are
copied from the original Cavium / Marvell U-Boot source code, enabling
booting into the Linux kernel.
Signed-off-by: Stefan Roese <sr@denx.de>
As noticed while working on the USB xHCI support, Octeon needs to flush
all pending writes so that the values are present in the memory. Add
this "syncw" instruction (twice) to flush_dcache_range().
Signed-off-by: Stefan Roese <sr@denx.de>
Import platform specific mangle-port.h header, allowing a area specific
swapping, which is needed on Octeon for USB & PCI areas.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
Import octeon_should_swizzle_table[] which is needed for the area
specific swapping. It will be used by the platform specific
mangle-port.h header.
Imported from Linux v5.7.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the initialization call for the Octeon RAM driver to
the Octeon platforms code. So if enabled via Kconfig, the DDR driver
will be called and the RAM will be configured and used. If the RAM
driver is not enabled, the L2 cache is still used as RAM.
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header will be used by the DDR driver (lmc). Its ported from the
2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This header is used by the upcoming DDR driver and potentially by other
drivers ported from the 2013 Cavium / Marvell U-Boot repository.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the memory controller (LMC) DT node to the Octeon 3 dtsi
file. It also adds the L2C DT node, as this is referenced by the DDR
driver.
Signed-off-by: Stefan Roese <sr@denx.de>
The GPIO bank name for banks J and K are not correct when using the
'gpio' command from the console.
The driver derives the bank name from the device tree instance string by
using the instance value and adding 'A': gpio0@xxaddrxx is Bank A,
gpio1@yyaddryy is Bank B and so on.
On the PIC32, there is no Bank I so instances 8 and 9 need to be
incremented as a minimum change.
An alternative (less opaque) implementation would be to use a bank-name
property instead but this would require modifying the driver code too.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
GPIO state cannot be changed via the device tree (e.g. with gpio-hog) or
using the 'gpio' command from the console.
The root cause is a discrepancy between the driver and the device tree:
the driver code expects an absolute I/O address in the <reg> property,
while the device tree defines the address relative to a declaration in
the parent pinctrl node.
Changing the device tree to fix a driver issue would normally be wrong,
however:
- I have run the first version of U-Boot in which this driver appears
(v2016.03) and the same problem exists, so this is not a regression;
- There is no code that references a parent device tree node that might
suggest the intent of the author was to parse the DT as it exists now;
- The equivalent Linux PIC32 GPIO driver also uses absolute addresses
for the GPIO <reg> property. This change brings the U-Boot DT more
into line with Linux.
Additionally, the data sheet (Microchip ref. 60001361H) shows that the
register set to control a GPIO bank spans 0xE0 bytes, but the device
tree specified size is only 0x48 bytes.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
The PIC32MZ DA Starter Kit does not need the card detect workaround
because the SDCD signal line is connected properly. Disable the
workaround in this case.
Signed-off-by: John Robertson <john.robertson@simiatec.com>
With the planned removal of bi_memstart & bi_memsize, this patch now
moves the references to the better suiting gd->ram_base/ram_size
variables.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This header file should not be included in other header files. Remove it
from each one and use a forward declaration instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch selects DM_SPI & DM_I2C for MIPS Octeon. DM_GPIO, DM_SERIAL
and DM_ETH are already selected.
Additionally the selections are now alphabetically sorted.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds very basic minimal support for the Marvell Octeon 3
CN73xx based EBB7304 EVK. Please note that the basic Octeon port does
not support DDR3/4 initialization yet. To still use U-Boot on with this
port, the L2 cache (4MiB) is used as RAM. This way, U-Boot can boot
to the prompt on this board.
Supported devices:
- UART
- reset
- CFI parallel NOR flash
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the code to copy itself from bootrom location to a
different location (TEXT_BASE) to the Octeon platform. Its used in
this case to copy the complete U-Boot image into L2 cache, which
greatly improves the bootup time - especially in regard to the
very long and complex DDR4 init code.
The Kconfig symbol CONFIG_MIPS_MACH_EARLY_INIT is enabled with this
patch for Octeon.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds very basic support for the Octeon III SoCs. Only
CFI parallel NOR flash and UART is supported for now.
Please note that the basic Octeon port does not include the DDR3/4
initialization yet. This will be added in some follow-up patches
later. To still use U-Boot on with this port, the L2 cache (4MiB on
Octeon III CN73xx) is used as RAM. This way, U-Boot can boot to the
prompt on such boards.
Signed-off-by: Aaron Williams <awilliams@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the optional call to mips_mach_early_init() to start.S
at a very early stage. Its disabled per default. It can be used for
very early machine / platform specific init code. Its called very
early and at this stage the PC is allowed to differ from the linking
address (CONFIG_TEXT_BASE) as no absolute jump has been performed until
this call.
It will be used by thje Octeon platform.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Sync asm/mipsregs.h with Linux 5.7. Also replace the custom
symbols EBASE_CPUNUM and EBASE_WG with the according symbols
from Linux.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Sync asm/addrspace.h with Linux 5.7
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Sync asm/asm.h with Linux 5.7.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This macro only served as a wrapper for CKSEG1ADDR() with an
exception for CONFIG_TB0229. CONFIG_TB0229 doesn't exist, thus
use CKSEG1ADDR() directly.
This also prepares for an upcoming asm header sync with Linux.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Add an own Kconfig symbol for the initial disabling of caches
invoked from generic start code.
Also add an own Kconfig symbols for the initialization of caches
invoked from generic start code.
Until now both code paths could only be disabled with
CONFIG_SKIP_LOWLEVEL_INIT. But this is not flexible enough for
RAM boot scenarios like EJTAG or SPL payload or for machines
which don't require cache initialization or which want to
provide their own cache implementation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Logically this code belongs to cache_init.S.
If a complex SoC needs to replace the generic cache init,
mips_cache_disable() can now be called from custom start.S files.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
change_k0_cca() is called multiple times. Move the code for
changing to KSEG1 to a macro to avoid code duplication.
Also fix missing change to KSEG1 when changing to CONF_CM_CACHABLE_COW.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Since commit 703ec9ddf9 ("MIPS: Stop building position independent code")
the relocation code was completely reworked and removed from start.S.
Remove some left-overs of the old code.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
This patch adds __weak to invalidate_dcache_range() in lib/cache.c. This
makes it possible to overwrite this function by a platforms specific
version, which will be done for Octeon.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds __weak to flush_cache() in lib/cache.c. This makes it
possible to overwrite this function by a platforms specific version,
like done with the Octeon base port.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the usage of CONFIG_MIPS_L2_CACHE without
CONFIG_MIPS_CM, which is what is needed for the newly added Octeon
platform.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the R_MIPS_NONE define from 0 to a magic value. This
makes it possible to better detect any forbidden pre-relocation usage
of BSS variables, as they are often zero'ed and then relocation is
stopped too early.
Additionally the error message is improved to also print the faulting
address. This helps finding the root-cause for this breakage by
comparing this address with the values in System.map.
This patch helps a lot when working on pre-relocation code, like the
Octeon DDR init code, where such variables have hit me multiple times
now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Aaron Williams <awilliams@marvell.com>
Cc: Chandrakala Chavva <cchavva@marvell.com>
This patch opts-out the compilation of get_tbclk() if
CONFIG_SYS_MIPS_TIMER_FREQ is not defined. This is used on the Octeon
platform, where the weak get_tbclk() function is overwritten by its
platform specific one.
Signed-off-by: Stefan Roese <sr@denx.de>
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.
Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.
This requires quite a few header-file additions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Small patch to add support for VoCore/VoCore2 board.
VoCore is open hardware and runs OpenWrt/LEDE.
It has WIFI, USB, UART, 20+ GPIOs but is only one inch square.
It will help you to make a smart house, study embedded system
or even make the tiniest router in the world.
Details about this SoM can be found at "https://vocore.io/v2.html".
Signed-off-by: Mauro Condarelli <mc5686@mclink.it>
Reviewed-by: Stefan Roese <sr@denx.de>
The current implementations have some issues detecting the correct
values:
dqs_find_max() will return "last passing fieldval + 1" instead of
"last passing fieldval". Also it will return "maxval + 1" in the
case that all fieldvals are tested valid (without error).
dqs_find_min() will not test the "lowest" value because of using ">"
instead of ">=".
This patch now rewrites these functions to fix those issues. Also,
this patch uses the same approach of a for loop in both functions making
it easier to read and maintain.
Since the variables are integers now, we can use min()/max(), which
handles the wrap around case for fieldval=0: return (0 - 1).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This change is made to enable comparison of integer variables, which
might be negative in the next patch. No functional change is intended
in this patch.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This function returns "-1" (true) upon error. So the function name does
not match its implementation which is confusing. This patch renames the
function to dqs_test_error() which makes the code easier to read.
Also change the return type to bool and return "true" or "false".
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds support for mt7628 reference board. SPL_DM and DT are not
enabled for SPL to save about 17KiB for u-boot-spl.bin.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch enables SPL for all mtmips boards. And also remove defconfig
files which are intend to build ram bootable u-boot files.
SPL_DM and OF_CONTROL are enabled for both boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds SPL support for mtmips platform. The lowlevel architecture
is split into SPL and the rest parts are built into a memory loadable
u-boot image. Optional SPL_DM and OF_CONTROL are also supported.
The increment of size is very small (< 10 KiB) if SPL_DM and OF_CONTROL are
not enabled and the memory bootable u-boot (u-boot.img) is generated
automatically so there is not need to add a separate config for it.
A lzma compressed payload (u-boot-lzma.img) is also generated and it will
be combined with u-boot-spl.bin to form the unified ROM bootable binary
u-boot-mtmips.bin.
A spl loader is added to support uncompress the payload.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch rewrites the mtmips architecture with the following changes:
1. Move MT7628 soc parts into a subfolder.
2. Lock parts of D-Cache as temporary stack.
3. Reimplement DDR initialization in C language.
4. Reimplement DDR calibration in a clear logic.
5. Add full support for auto size detection for DDR1 and DDR2.
6. Use accurate CPU clock depending on the input xtal frequency for timer
and delay functions.
Note:
print_cpuinfo() has incompatible parts with MT7620 so it's moved into
mt7628 subfolder.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The initial stack on some platforms is too small to hold a large malloc
space. This patch adds a option to allow these platforms not reserving the
malloc space on initial stack. These platforms should set the malloc base
after DRAM is usable.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently CONFIG_MIPS_INIT_STACK_IN_SRAM assumes the memory space for the
initial stack can be used directly. However on some platform the SRAM needs
initialization, e.g. lock cache.
This patch adds an option to allow a new function mips_sram_init() being
called before setup_stack_gd.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a new pinmux for UART2, which shares the pins with SPIS.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
