VPXA2785(vp-x-a2785-00) is evaluation board which contains two PCIe-Edge
fingers, one for PCIe-B(gen5x8) and one for CPM(dual gen5x8, gen5x16).
Each of the ports can operate in endpoint or root port mode. This allows
the single card to be used for both root port, endpoint, and switch modes.
The board is designed in the similar manner as others Versal boards. It
means board also have ZynqMP Zu4 System Controller which is described in a
separate file.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/59d3b1f7e785bc65518b465e5122fd2787616a93.1695808407.git.michal.simek@amd.com
System controller revC is using ADI ethernet phy instead of TI because of
supply chain issues.
Describe reset assert and de-assert times to 10us and 5ms respectively
according to the datasheet. Also setup RGMII RX and TX delay values to
2400ps as per board bring up observations.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/2790f6cede7485556d581ab8270dda477fa21522.1695808407.git.michal.simek@amd.com
System controllers are pretty much the same on the all boards that's why
use autodetection based on i2c eeprom. This should end up with having only
one BSP for all SCs with only DT overlays to cover different i2c
structures.
All MIOs are fixed by the spec that's why not a problem to description
pinctrl setting.
Apart from eth phy reset, it also set proper phy delays.
The TI DP83867 PHY datasheet says:
T1: Post RESET stabilization time == 195us
T3: Hardware configuration pins transition to output drivers == 64us
T4: RESET pulse width == 1us
So with a little overhead set 'reset-assert-us' to 100us (T4) and
'reset-deassert-us' to 280us (T1+T3).
NOTE: The tuning of TI DP83867 phy reset delay is derived from linux
upstream commit: 5dbadc848259(arm64: dts: fsl: add support for Kontron
pitx-imx8m board).
i2c structure on Xilinx Versal evaluation platforms contain a lot of
devices but also connection to connectors like SFP. Because of this
complicated structure with also all level shifters, i2c muxes, etc. not all
devices are able to reliably work on 400kHz even if they are compatible
with this speed. That's why set i2c frequency to 100KHz to increase
reliability of the i2c bus.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8092340f92144f0cc9096194198f227015bc013.1695808407.git.michal.simek@amd.com
BeagleBoard.org BeaglePlay is an easy to use, affordable open source
hardware single board computer based on the Texas Instruments AM625
SoC that allows you to create connected devices that work even at long
distances using IEEE 802.15.4g LR-WPAN and IEEE 802.3cg 10Base-T1L.
Expansion is provided over open standards based mikroBUS, Grove and
QWIIC headers among other interfaces.
This board family can be identified by the 24c32 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 45 41 47 4c 45 |.U3..7....BEAGLE|]
[50 4c 41 59 2d 41 30 2d 00 00 30 32 30 30 37 38 |PLAY-A0-..020078|]
https://beagleplay.org/https://git.beagleboard.org/beagleplay/beagleplay
baseline of base device tree is v6.5-rc1.
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Co-developed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmTu+QMcHGV1Z2VuLmhy
aXN0ZXZAY29sbGFib3JhLmNvbQAKCRAesx4CDqwvyFqVB/9z5lV4zhqWYiQ+wNZL
Gxs3//DSS5iVHU+xaPRrYQT99Yn2/kfM2LeQ4REBOaOTP7IX2ewmOEro4OUViFuC
kt/WnHD0XzN+2o8akIdVC5YudgVcuX751SQtp5dqcbN6FylSH010+YIZTvaJoNQn
+Wny1ZZhpuNJJEPvLxE/eiJ3jFwvEAjC+jH328uQIeSLknPh93hGJOFc/02F0O2o
s96J1/VZ4qvvQKYw0sgNtGb/0Og7V0RLW27+RfwhH4XJvAIv/A6MioTyRaCS2h7H
tzj/hFXbzGtu+AqrEtMgNjzC7vAx+0266P/Zx/DOWKoWLDIYkWSLpYKLut0E6CUe
+fcB
=L/iw
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2023.10-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2023.10 cycle:
This feature set includes a new board sama5d29 Curiosity, and various
fixes and alignments for sam9x60 and sam9x60 curiosity board.
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
-----BEGIN PGP SIGNATURE-----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=Bzgn
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-2023.10-rc1' of https://source.denx.de/u-boot/custodians/u-boot-tegra
ARM: tegra: Changes for v2023.10-rc1
This adds support for various new Tegra30 boards (ASUS, LG and HTC) and
has some other minor enhancements, such as enabling the poweroff command
on several Tegra210 and Tegra186 boards.
LubanCat2 is a rk3568 based SBC from EmbedFire.
Specification:
- Rockchip rk3568
- LPDDR4/4X 1/2/4/8 GB
- TF scard slot
- eMMC 8/32/64/128 GB
- Gigabit ethernet x 2
- HDMI out
- USB 2.0 Host x 1
- USB 2.0 Type-C OTG x 1
- USB 3.0 Host x 1
- Mini PCIE interface for WIFI/BT module
- M.2 key for 2280 NVME
- 40 pin header
The dts file is sync from linux mainline.
Signed-off-by: Andy Yan <andyshrk@163.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This adds initial support for the Toradex Verdin AM62 Quad 1GB WB IT
V1.0A module and subsequent V1.1 launch configuration SKUs. They are
strapped to boot from their on-module eMMC. U-Boot supports booting
from the on-module eMMC only, DFU support is disabled for now due to
missing AM62x USB support.
The device trees were taken straight from Linux v6.5-rc1.
Boot sequence is:
SYSFW ---> R5 SPL (both in tiboot3.bin) ---> ATF (TF-A) ---> OP-TEE
---> A53 SPL (part of tispl.bin) ---> U-boot proper (u-boot.img)
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
This patch adds general board files based on MT7988 SoCs.
MT7988 uses one mmc controller for booting from both SD and eMMC,
and the pins of mmc controller booting from SD are also shared with
one of spi controllers.
So two configs are need for these boot types:
1. mt7988_rfb_defconfig - SPI-NOR, SPI-NAND and eMMC
2. mt7988_sd_rfb_defconfig - SPI-NAND and SD
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.
Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT
Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion
Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.
Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
FriendlyARM NanoPi R5C is an open-sourced mini IoT gateway device.
Specification:
- Rockchip RK3568
- 1/4GB LPDDR4X RAM
- 8/32GB eMMC
- SD card slot
- M.2 Connector
- 2x USB 3.0 Port
- 2x 2500 Base-T (PCIe, r8125)
- HDMI 2.0
- MIPI DSI/CSI
- USB Type C 5V
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
The device tree and description are taken from kernel v6.3-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Add support for Versal NET mini Octal SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Octal SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Versal NET mini Quad SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Quad SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The HTC One X is a touchscreen-based, slate-sized smartphone
designed and manufactured by HTC that runs the Android operating
system. The One X features a 4.7" display, an Nvidia Tegra 3
quad-core chip, 1 GB of RAM and non-extendable 32 GB of internal
storage. UART-A is default debug port.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com>
Tested-by: Ion Agorria <ion@agorria.com>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
LG X3 is a development board based on Nvidia Tegra 3 SoC
on base of which Optimus 4X HD and Optimus Vu were created.
Both smartphones feature a 4.7" and 5" panels respectively,
an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 16/32 GB
of internal storage. Optimux 4X HD additionally has a micro
SD slot.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nexus 7 is a mini tablet computer co-developed by Google and Asus
that runs the Android operating system. The Nexus 7 features a 7"
display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 8/16 GB
of internal storage.
This patch brings support for all 3 known ASUS/Google devices:
- Nexus 7 (2012) E1565
- Nexus 7 (2012) PM269
- Nexus 7 (2012) 3G - tilapia
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS Grouper E1565
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ASUS Transformer T30 family are 2-in-1 detachable tablets
and AiO developed by ASUS that run the Android operating system
(TF600T runs Windows RT and P1801-T runs Android and Windows).
The T30 Transformers feature a 10.1-inch display (apart P1801-T),
an Nvidia Tegra 3 quad-core chip, 1/2 GB of RAM, and 16/32 GB of
storage. Transformers board derives from Nvidia Cardhu development
board.
This patch brings support for 7 known Transformer devices:
- ASUS Transformer Prime TF201
- ASUS Transformer Pad TF300T/TF300TG/TF300TL
- ASUS VivoTab RT TF600T (Windows RT based)
- ASUS Transformer Infinity TF700T
- ASUS Portable AiO P1801-T
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # all devices
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Import the device tree from mainline linux (v6.4-rc1) and add the
old PHY reset bindings in the PHY node, else U-Boot and linux won't
be able to use the PHY.
Signed-off-by: Ferass El Hafidi <vitali64pmemail@protonmail.com>
Link: https://lore.kernel.org/r/20230507124109.31778-2-vitali64pmemail@protonmail.com
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add meson-a1-ad401.dts file from Linux 6.3-rc7
Signed-off-by: Igor Prusov <ivprusov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230505125639.3605-3-ivprusov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Add board code for the R8A77980 V3HSK board.
Add CPLD sysreset driver to the R-Car V3H SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3H Condor, squash CPLD driver in]
Add board code for the R8A77970 V3MSK board.
Add CPLD sysreset driver to the R-Car V3M SK board.
Extracted from a larger patch by Valentine Barshak.
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
[Marek: Sync configs and board code with V3M Eagle, squash CPLD driver in]
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Linux commit 246450344dad arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
Add support for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
sync dts{,i} files for Radxa ROCK Pi 4 series with Linux 6.3.
because rk3399-rock-pi-4a.dts is enough for ROCK Pi 4A/B/A+/B+ and ROCK
4SE, delete dts{,i} for ROCK Pi 4B.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
