This ID disappeared in 5b66fdb29d ("mtd: spi: Remove unused files"),
add the ID back, since the chip is used on devices supported by U-Boot.
Fixes: 5b66fdb29d ("mtd: spi: Remove unused files")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to datasheet, the upper four bits are reserved or used for
reflecting the ECC status of the accumulated pages. The error bits
number for the worst segment of the current page is encoded on lower
four bits. Fix it by masking the upper bits.
This same issue has been already fixed in the linux kernel by:
"mtd: spinand: macronix: Fix ECC Status Read"
(sha1: f4cb4d7b46f6409382fd981eec9556e1f3c1dc5d)
Apply the same fix in the U-Boot driver.
Signed-off-by: Haolin Li <li.haolin@qq.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
-----BEGIN PGP SIGNATURE-----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=pDip
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20211007' of https://source.denx.de/u-boot/custodians/u-boot-amlogic
- Add new SoC ID for S905Y2 found in Radxa Zero
- pcie_dw_meson: fix usb fail when pci link fails to go up
- Sync Amlogic DT from Linux 5.14
- dwc3-meson-gxl: add AXG compatible
- dts: keep back HW order for MMC devices since change in Upstream Linux
- Cleanup local AXG DT USB nodes now everything is upstream
- distro_bootcmd: run pci enum for scsi_boot just like it is done for nvme_boot
- New Boards:
- Odroid-HC4: a variant of Odroid-C4 with 2 SATA ports (via PCIe-SATA bridge)
- Beelink GS-King X: A variant of the other Beelink board with 2 SATA ports (via USB3-SATA bridge)
- Banana Pi M5: another credit card SBC
- JetHub D1/H1: home automation controllers
- Radxa Zero: another RPi Zero sized SBC
Add documentation bits for the Radxa Zero
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add a defconfig for the Radxa Zero SBC, using an Amlogic S905Y2 chip.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
[narmstrong: updated u200 MAINTAINERS & add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the initial dts queued for Linux 5.16.y
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Alpha sort the Amlogic dtb list (same as the kernel).
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for new home automation devices.
JetHome Jethub D1 (http://jethome.ru/jethub-d1) is a home automation controller with the following features:
- DIN Rail Mounting case
- Amlogic A113X (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 512Mb/1GB DDR3
- 8/16GB eMMC flash
- 1 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth AMPAK AP6255 (Broadcom BCM43455) IEEE 802.11a/b/g/n/ac, Bluetooth 4.2.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- 2 x gpio LEDS
- GPIO user Button
- 1 x 1-Wire
- 2 x RS-485
- 4 x dry contact digital GPIO inputs
- 3 x relay GPIO outputs
- DC source with a voltage of 9 to 56 V / Passive POE
JetHome Jethub H1 (http://jethome.ru/jethub-h1) is a home automation controller with the following features:
- Square plastic case
- Amlogic S905W (ARM Cortex-A53) quad-core up to 1.5GHz
- no video out
- 1GB DDR3
- 8/16GB eMMC flash
- 2 x USB 2.0
- 1 x 10/100Mbps ethernet
- WiFi / Bluetooth RTL8822CS IEEE 802.11a/b/g/n/ac, Bluetooth 5.0.
- TI CC2538 + CC2592 Zigbee Wireless Module with up to 20dBm output power and Zigbee 3.0 support.
- MicroSD 2.x/3.x/4.x DS/HS cards.
- 1 x gpio LED
- ADC user Button
- DC source 5V microUSB with serial console
Patches from:
- JetHub H1
https://lore.kernel.org/r/20210915085715.1134940-4-adeep@lexina.inhttps://git.kernel.org/amlogic/c/abfaae24ecf3e7f00508b60fa05e2b6789b8f607
- JetHub D1
https://lore.kernel.org/r/20210915085715.1134940-5-adeep@lexina.inhttps://git.kernel.org/amlogic/c/8e279fb2903990cc6296ec56b3b80b2f854b6c79
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
[narmstrong: removed unused variable value]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
JetHub devices uses its own boot sequence with "rescue" button
Signed-off-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Beelink GS-King X is a variant of the GS King boards but with an internal
USB to SATA bridge and advanced audio features.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Odroid-HC4 is a variant of the Odroid-C4 board but with a PCIe-SATA bridge
instead of the USB3 ports.
[narmstrong: add missing CONFIG_SYS_LOAD_ADDR from defconfig]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SCSI device can be a PCIe adapter, so run pcie enum if enabled.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SCSI target to be able to boot from the SATA disks on the Odroid HC4 using
an on-board AHCI PCIe controller.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Since Linux commmit [1], the order is fixed with aliases, in order to keep the
MMC device order, set it back to HW order in U-Boot dtsi files.
[1] ab547c4fb39f ("arm64: dts: amlogic: Assign a fixed index to mmc devices")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Upstream Linux uses the "amlogic,meson-axg-usb-ctrl" for AXG SoCs.
This adds it to the compatible list for this driver.
Reported-by: Vyacheslav Bocharov <adeep@lexina.in>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Vyacheslav Bocharov <adeep@lexina.in>
Import Amlogic DT changes from Linux commit 7d2a07b76933 ("Linux 5.14"),
dt-bindings clock changes and new meson-g12b-gsking-x.dts,
meson-sm1-bananapi-m5 & odroid-hc4 boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
On Amlogic A311D, when the PCIe link fails disabling the related clocks
makes USB fail. For an unknown reason, this doesn happen on the S905D3 SoC.
Mimic the Linux behavior by not considering a link failure a probe failure,
and continue even if the PCIe link is down.
Reported-by: Art Nikpal <email2tema@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the SOC ID for the S905Y2 to board info, see below for before/after
tested with a Radxa Zero board:
SoC: Amlogic Meson G12A (Unknown) Revision 28:b (30:2)
SoC: Amlogic Meson G12A (S905Y2) Revision 28:b (30:2)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
If Coherence Manager were not set in the beginning,
u-boot-spl would sometimes fail to boot to u-boot proper.
Enable CM and I/D cache at the same time in harts_early_init
Signed-off-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Rick Chen <rick@andestech.com>
There should be a platform compiled with the new driver.
Enable CONFIG_SYSRESET_SBI for all QEMU boards using SBI.
If you want to test the SBI sysreset driver, disable
CONFIG_SYSRESET_SYSCON.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Provide sysreset driver using the SBI system reset extension.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Samuel Holland <samuel@sholland.org>
Use constants for extension IDs.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add the System Reset Extension and the Hart State Management Extension
definitions.
Add missing RFENCE Extension enum values.
The SBI 0.1 extension constants are needed for the sbi command. Remove
an #ifdef.
Cf. https://github.com/riscv/riscv-sbi-doc/blob/master/riscv-sbi.adoc
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
bootm_low is used as a base address is used to allocate space for the
FDT blob, initrd, cmdline, etc. when booting Linux. Set the default
value for RISC-V to the start of the first DRAM bank, so platforms can
get their DRAM layout from the device tree, and do not need to define
CONFIG_SYS_SDRAM_BASE.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The no-map property is wrongly skipped if a no-map reserved memory
node follows one without that property. Fix this by not remembering
the absence of a no-map property across loop iterations.
Fixes: d4ea649f17 ("riscv: Provide a mechanism to fix DT for reserved memory")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
The RISC-V SBI interface v0.1 provides a function for printing a
character to the console. Even though SBI v0.1 functions are deprecated,
the SBI console is quite useful for early debugging, because it works
without any dcache, memory, or MMIO access in S mode.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In some cases, the best config cannot be used because the VCO would be
out-of-spec. In these cases, we may need to try a worse combination of r/od
in order to find the best representable config. This also adds a few test
cases to catch this and other (possible) unlikely errors.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Having to copy-paste the same 3 lines makes adding new test cases
error-prone. Use a macro.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Everything here sits in a while (true) loop. However, this introduces a
couple of layers of indentation. We can simplify the code by introducing a
single goto instead of using continue/break. This will also make adding
loops in the next patch easier.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The PLL functions take ulong arguments for rate, but still check if that
rate is negative (which is never true). The correct way to handle this is
to use IS_ERR_VALUE (like is already done in k210_clk_set_rate). While
we're at it, we can move the error checking up into the caller of the pll
set/get rate functions. This also protects our other calculations from
using bogus values for rate.
Fixes: 609bd60b94 ("clk: k210: Rewrite to remove CCF")
Reported-by: Coverity Scan <scan-admin@coverity.com>
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The values of CONFIG_NAND_OMAP_ECCSCHEME map to the enum in
include/linux/mtd/omap_gpmc.h for valid ECC schemes. Make which one we
will use be a choice statement, enumerating the ones which we have
implemented.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_NAND_FSL_ELBC
CONFIG_NAND_FSL_IFC
Note that a number of PowerPC platforms had previously enabled
CONFIG_NAND_FSL_ELBC without CONFIG_MTD_RAW_NAND, and now they no longer
enable the option, reducing the size of a few functions.
Signed-off-by: Tom Rini <trini@konsulko.com>
We only include <linux/mtd/rawnand.h> in <nand.h> for the forward
declaration of struct nand_chip, so do that directly. Then, include
<linux/mtd/rawnand.h> where required directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SYS_NAND_BAD_BLOCK_POS
In order to do this, introduce a choice for HAS_LARGE/SMALL_BADBLOCK_POS
as those are the only valid values. Use LARGE as the default as no
in-tree boards use SMALL, but it is possible.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_NAND_LOAD
CONFIG_SYS_NAND_BLOCK_SIZE
CONFIG_SYS_NAND_PAGE_SIZE
CONFIG_SYS_NAND_OOBSIZE
Signed-off-by: Tom Rini <trini@konsulko.com>
Typically platforms will define CONFIG_SYS_NAND_PAGE_COUNT based on
CONFIG_SYS_NAND_BLOCK_SIZE / CONFIG_SYS_NAND_PAGE_SIZE. Switch to this
in preparation for migrating CONFIG_SYS_NAND namespace to Kconfig.
Cc: Marek Vasut <marex@denx.de>
Cc: Olaf Mandel <o.mandel@menlosystems.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These platforms do not currently enable NAND, remove these references.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
