Commit graph

2387 commits

Author SHA1 Message Date
Philipp Tomsich
ff143d5556 arm: mark save_boot_params_ret as a function
As no '.type' was set for save_boot_params_ret in start.S, binutils
did not track whether it was emitted as A32 or T32.  By properly
marking save_boot_params_ret as a potential function entry, we can
make sure that the compiler will insert the appropriate instructions
for branching to save_boot_params_ret both for call-sites emitted as
A32 and T32.

Reported-by: Andy Yan <andy.yan@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Andy Yan <andy.yan@rock-chips.com>
2017-11-21 23:57:22 +01:00
Patrice Chotard
1537d38619 stv0991: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STV0991
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Patrice Chotard
3bc599c956 stm32: fix STMicroelectronics copyright
Uniformize STMicroelectronics copyrights headers for STM32
related code.

Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
2017-11-06 09:51:01 -05:00
Ran Wang
0e8a4264ec armv7: Add workaround for USB erratum A-009007
Rx Compliance tests may fail intermittently at high
jitter frequencies using default register values

Program register USB_PHY_RX_OVRD_IN_HI in certain sequence
to make the Rx compliance test pass.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.bhagat@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:07 -07:00
Ran Wang
e10d114279 armv7: Add workaround for USB erratum A-008997
Low Frequency Periodic Singaling (LFPS) Peak-to-Peak Differential
Output Voltage Test Compliance fails using default transmitter settings

Change config of transmitter signal swings by setting register
PCSTXSWINGFULL to 0x47 to pass compliance tests.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
c1853f6f73 armv7: Add workaround for USB erratum A-009798
The default setting for USB High Speed Squelch Threshold results
in a threshold close to or lower than 100mV. This leads to Receive
Compliance test failure for a 100mV threshold.

Shift the threshold from ~100mV towards ~130mV by setting SQRXTUNE
to 0x0 to pass USB High Speed Receiver Sensitivity Compliance test.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ran Wang
83fa71189a armv7: Add workaround for USB erratum A-009008
USB High Speed (HS) EYE Height Adjustment
USB HS speed eye diagram fails with the default value at
many corners, particularly at a high temperature

Optimal eye at TXREFTUNE value to 0x9 is observed, change
set the same value.

Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: Reordered Kconfig options]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 08:01:06 -07:00
Ashish Kumar
63b2316c5c fsl-layerscape: Consolidate registers space defination for CCI-400 bus
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.

This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.

Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
2017-09-11 07:55:36 -07:00
Tom Rini
470135be27 Merge git://www.denx.de/git/u-boot-imx
Update pfla02 for setenv changes and PHYLIB/etc migration to Kconfig.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-08-16 18:12:00 -04:00
Simon Glass
382bee57f1 env: Rename setenv() to env_set()
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.

Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
2017-08-16 08:22:18 -04:00
Peng Fan
11d94319c3 arm: Implement workaround for Cortex-A9 errata 845369
Under very rare timing circumstances, transitioning into streaming
mode might create a data corruption. Present on Two or more processors
or 1 core with ACP, all revisions. This erratum can be worked round
by setting bit[22] of the undocumented Diagnostic Control Register to 1.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-08-16 11:50:51 +02:00
xypron.glpk@gmx.de
6def7de37b bcm281xx: clock: avoid possible NULL dereference
It does not make sense first to dereference c and then
to check if it is NULL.

The problem was indicated by cppcheck.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:27 -04:00
xypron.glpk@gmx.de
65e8ce29e4 arm: bcm235xx: clk_set_rate avoid possible NULL deref
It does not make sense first to dereference c and then
to check if it is NULL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:27 -04:00
xypron.glpk@gmx.de
b69a0849e7 arm: bcm235xx: avoid possible NULL dereference
It does not make sense to first dereference c and then
check if it is NULL.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
2017-08-13 15:17:26 -04:00
Simon Glass
6500ec7a5a Convert CONFIG_CMD_PCI to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_PCI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
2017-08-11 15:41:50 -04:00
Stefano Babic
552a848e4f imx: reorganize IMX code as other SOCs
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.

This change is also coherent with the structure in kernel.

Signed-off-by: Stefano Babic <sbabic@denx.de>

CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
2017-07-12 10:17:44 +02:00
Vanessa Maegima
d7c11502df mx6sabreauto: Update to SPL only mode
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.

This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Vanessa Maegima
823dff9d02 mx6qsabreauto: Add SPL support
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.

Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg

Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg

Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg

Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-07-12 09:44:22 +02:00
Fabio Estevam
a1d1fdc920 mx6: soc: Move mxs_dma_init() into the mxs nand driver
Currently the following build error is seen when a board using MMC SPL
is built and the MXS nand driver is also selected:

arch/arm/cpu/armv7/built-in.o: In function `arch_cpu_init':
arch/arm/cpu/armv7/mx6/soc.c:432: undefined reference to 'mxs_dma_init'

On mx6 the only user of mxs_dma_init() is the mxs nand driver, so
move it there.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-07-12 09:44:22 +02:00
Stefan Agner
3fd9579085 imx: mx6ull: fix USB bmode for i.MX 6UL and 6ULL
i.MX 6UL and 6ULL have different boot device capabilities and
use therefor use a different boot device selection table than
other i.MX 6 devices. Particularly, the value which has been
used so far (b0001) is assigned to QSPI boot for these two
devices.

There is no common reserved value for all i.MX 6devices. Use
b0010 for i.MX 6UL and 6ULL via compile time ifdef.

Reported-by: Joël Esponde <joel.esponde@honeywell.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Joël Esponde <joel.esponde@honeywell.com>
2017-07-12 09:42:33 +02:00
Simon Glass
8eab1a58dd dm: scsi: Document and rename the scsi_scan() parameter
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
10e40d54b3 Kconfig: Add CONFIG_SATA to enable SATA
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
3bf926c0dd Convert CONFIG_CMD_SATA to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_SATA

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Simon Glass
fedb428c5b Convert CONFIG_SCSI to Kconfig
This converts the following to Kconfig:
   CONFIG_SCSI

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
2017-07-11 10:08:19 -06:00
Tom Rini
821560fd8e Merge git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/imx6qdl_icore_rqs.h
	include/configs/imx6ul_geam.h
	include/configs/imx6ul_isiot.h
2017-06-27 09:32:37 -04:00
Fabio Estevam
65496a3483 mx6: soc: Fix typo in temperature unit name
The correct name is 'Celsius', so fix it accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-06-27 09:06:09 +02:00
Chen-Yu Tsai
3474827294 sunxi: psci: Move entry address setting to separate function
Currently we set the entry address in the psci_cpu_on function.
However R40 has a different register for this. This resulted in
an #ifdef / #else block in psci_cpu_on, which we avoided having
in the first place.

Move this part into a separate function, defined differently for
the R40 as opposed to the other single cluster platforms.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2017-06-12 15:41:02 +05:30
Tom Rini
ffb5656862 armv7: Mark the default lowlevel_init function as weak
Rather than have a long and if check in the Makefile, mark the default
lowlevel_init function as weak (as we do on armv8) so that SoCs can
override it if needed, and it will still be discarded if unused.
Provide a weak s_init as well to allow for this to link and be
discarded.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-06-05 11:02:23 -04:00
Vanessa Maegima
1541d7a63d pico-imx7d: Add initial support
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.

Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.

For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc

Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-05-31 09:58:40 +02:00
Simon Glass
51f2937036 Convert CONFIG_CMD_FUSE to Kconfig
This converts the following to Kconfig:
   CONFIG_CMD_FUSE

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-05-22 09:33:58 -04:00
Jagan Teki
bc1fe9006d icorem6: Make SPL to pick suitable fdt
SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
9786496cdc geam6ul: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Jagan Teki
98f5661033 icorem6: Add modeboot env via board_late_init
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-05-18 11:23:31 +02:00
Nisal Menuka
8776350d87 Add ARM errata workaround 852421 and 852423 for Cortex-A17
ARM errata 852421 and 852423 applies to r1p0, r1p1 and r1p2
revisions of Cortex-A17 processors. These workarounds
exist in Linux kernel and I thought it would be better
to add them in to U-Boot.

Signed-off-by: Nisal Menuka <nisalmenuka23@gmail.com>
2017-05-08 11:57:36 -04:00
Tom Rini
26d61195f8 fdt: Move fdt_fixup_ethernet to a common place
With 3f66149d9f we no longer have a common call fdt_fixup_ethernet.
This was fine to do on PowerPC as they largely had calls already in
ft_cpu_fixup.  On ARM however we largely relied on this call.  Rather
than introduce a large number of changes to ft_cpu_fixup /
ft_board_fixup we recognize that this is a common enough call that we
should be doing it in a central location.  Do it early enough that we
can do any further updates in ft_cpu_fixup / ft_board_fixup.

Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Thomas Chou <thomas@wytron.com.tw> (maintainer:NIOS)
Cc: York Sun <york.sun@nxp.com> (maintainer:POWERPC MPC85XX)
Cc: Stefan Roese <sr@denx.de> (maintainer:POWERPC PPC4XX)
Cc: Simon Glass <sjg@chromium.org>
Cc: Joakim Tjernlund <Joakim.Tjernlund@infinera.com>
Fixes: 3f66149d9f ("Remove extra fdt_fixup_ethernet() call")
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-05-01 09:11:59 -04:00
Tom Rini
29ec685883 arm: Re-sync ARCH_MX5 / MX51 / MX53 CONFIG options
A few boards had not been fully re-synced with CONFIG_ARCH_MX5 / CONFIG_MX51 /
CONFIG_MX53 being in Kconfig.  Do so now.

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-30 10:29:38 -04:00
Tom Rini
6f008a2e16 Merge git://git.denx.de/u-boot-sunxi 2017-04-25 16:12:42 -04:00
Chen-Yu Tsai
0918648d82 sunxi: Add PSCI support for R40
The R40's CPU controls are a combination of sun6i and sun7i.

All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.

Last, the R40 does not have a secure SRAM block.

This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:01 +02:00
Tom Rini
3c476d841d Merge git://git.denx.de/u-boot-fsl-qoriq 2017-04-18 11:36:06 -04:00
Masahiro Yamada
c54bcf6805 ARM: adjust arm-smccc code for use in U-Boot
Adjust ARM SMC Calling Convention code for U-Boot:
  - Replace the license block with SPDX
  - Change path to asm-offsets.h
  - Define UNWIND() as no-op
  - Add Kconfig entry
  - Add asm-offsets

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:17 -04:00
Masahiro Yamada
c2da86f39e ARM: import arm-smccc code from Linux 4.11-rc6
Imports ARM SMC Calling Convention code from Linux 4.11-rc6.
The files have been copied as follows:

[Linux]                           [U-Boot]
arch/arm/kernel/smccc-call.S   -> arch/arm/cpu/armv7/smccc-call.S
arch/arm64/kernel/smccc-call.S -> arch/arm/cpu/armv8/smccc-call.S
arch/arm/include/asm/opcodes*  -> arch/arm/include/asm/opcodes*
include/linux/arm-smccc.h      -> include/linux/arm-smccc.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-04-18 10:29:16 -04:00
York Sun
73fb583829 armv7: ls1021a: Drop macro CONFIG_LS102XA
Use CONFIG_ARCH_LS1021A instead.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-04-17 09:03:30 -07:00
Tom Rini
3fea953698 Merge branch 'master' of git://git.denx.de/u-boot-video 2017-04-14 22:05:17 -04:00
Sanchayan Maity
b215fb3f34 Convert CONFIG_FSL_DCU_FB to Kconfig
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
2017-04-14 13:37:35 +02:00
Tom Rini
1622559066 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Drop CONFIG_STACKSIZE from include/configs/imx6_logic.h

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-04-13 11:19:00 -04:00
Adam Ford
f479cec3b6 imx: i.mx6q: add the initial support for LogicPD i.MX6Q SOM
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash.  The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM.  Items in the dtsi file
are specific to the SOM itself.  Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.

Signed-off-by: Adam Ford <aford173@gmail.com>
2017-04-12 18:59:12 +02:00
Ye Li
2018ef868c imx: mx7ulp: Fix SPLL/APLL clock rate calculation issue
The num/denom is a float value, but in the calculation it is convert
to integer 0, and wrong result.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-04-12 18:45:10 +02:00
Andre Przywara
4d24e5f175 fsl: ls102x: remove redundant GENERIC_TIMER_CLK
Some Freescale boards used an extra version of the constant to hold the
Generic Timer frequency. This can easily be covered by the now unified
COUNTER_FREQUENCY constant, so remove this extra variable from those
boards.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
e4916e850b ARM: rename CONFIG_TIMER_CLK_FREQ to COUNTER_FREQUENCY
Many ARMv8 boards define a constant COUNTER_FREQUENCY to specify the
frequency of the ARM Generic Timer (aka. arch timer).
ARMv7 boards traditionally used CONFIG_TIMER_CLK_FREQ for the same
purpose. It seems useful to unify them.
Since there are less occurences of the latter version, lets convert all
users over to COUNTER_FREQUENCY.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Jagan Teki
a2f8a45696 configs: imx6: Select missing BOARD_LATE_INIT
Select missing BOARD_LATE_INIT from configs/ to
respective targets on arch area for Engicam imx6 boards.

Cc: Tom Rini <trini@konsulko.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-26 11:05:57 +02:00
Tom Rini
02ccab1908 Merge branch 'master' of git://www.denx.de/git/u-boot-imx
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/bk4r1_defconfig
	configs/colibri_vf_defconfig
	configs/pcm052_defconfig
	include/configs/colibri_vf.h
	include/configs/pcm052.h
2017-03-19 15:13:38 -04:00
Stefan Agner
7966b43778 ARM: vf610: move to standard arch/board approach
Move Freescale/NXP Vybrid to a standard arch/board approach, similar
to what has been done to i.MX 6 earlier in commit 89ebc82137 ("ARM:
mx6: move to a standard arch/board approach").

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
2017-03-19 17:30:11 +01:00
Fabio Estevam
9b548bf856 mx7: Add 1.2GHz speed grade entry
There are recent MX7 parts that have a 1.2GHz speed grade.

Add support for it.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19 17:29:03 +01:00
Fabio Estevam
60a07fb843 mx7: Fix the get_cpu_speed_grade_hz() return values
According to the MX7D fuse map the following speed grades are available:

800  MHz
500  MHz
1000 MHz
1200 MHz

So simply return the real frequency that corresponds to the speed grade.

With this change we see on boot:

CPU:   Freescale i.MX7D rev1.2 1000 MHz (running at 792 MHz)

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19 17:28:59 +01:00
Fabio Estevam
31b8a9011b mx7: Fix speed grade entry
According to the MX7D fuse map the speed grade of the parts, which
return '1' is 500MHz instead of 850MHz, so fix it accordingly.

Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
2017-03-19 17:28:55 +01:00
Sébastien Szymanski
77f29293f1 arm: i.MX6UL: add Armadeus Systems OPOS6UL SoM and OPOS6ULDev carrier board
OPOS6UL is an i.MX6UL based SoM with 256MB RAM, 4GB eMMC and an ethernet
phy. OPOS6ULDev is carrier board for the OPOS6UL.

U-Boot SPL 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09)
Trying to boot from MMC1

U-Boot 2017.03-rc3-00002-g5085c26 (Mar 07 2017 - 09:48:09 +0100)

CPU:   Freescale i.MX6UL rev1.0 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 40C
Reset cause: POR
Model: Armadeus Systems OPOS6UL SoM on OPOS6ULDev board
DRAM:  256 MiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Video: 800x480x18
In:    serial
Out:   serial
Err:   serial
Net:   FEC [PRIME]
Hit any key to stop autoboot:  0

Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2017-03-19 17:28:09 +01:00
Tom Rini
3a649407a4 arm: Migrate SYS_THUMB_BUILD to Kconfig, introduce SPL_SYS_THUMB_BUILD
Today, we have cases where we wish to build all of U-Boot in Thumb2 mode for
various reasons.  We also have cases where we only build SPL in Thumb2 mode due
to size constraints and wish to build the rest of the system in ARM mode.  So
in this migration we introduce a new symbol as well, SPL_SYS_THUMB_BUILD to
control if we build everything or just SPL (or in theory, just U-Boot) in
Thumb2 mode.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
2017-03-18 20:28:01 -04:00
Jagan Teki
0421a164de imx6: isiotmx6ul: Add FEC support
Add FEC support for Engicam Is.IoT MX6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17 09:27:08 +01:00
Jagan Teki
e411e67e1e imx6: isiotmx6ul: Add I2C support
Add I2C support for Engicam Is.IoT MX6UL module.

isiotmx6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
isiotmx6ul> i2c dev 0
Setting bus to 0
isiotmx6ul> i2c dev
Current bus is 0
isiotmx6ul> i2c speed 100000
Setting bus speed to 100000 Hz
isiotmx6ul> i2c probe
Valid chip addresses: 00 2C 44 78
isiotmx6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17 09:27:08 +01:00
Jagan Teki
e9dfa1e1e5 arm: imx6ul: Add Engicam Is.IoT MX6UL Starter Kit initial support
Boot from MMC:
-------------
U-Boot SPL 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33)
Trying to boot from MMC1

U-Boot 2017.01-rc2-gba3c151-dirty (Jan 02 2017 - 16:59:33 +0100)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 33C
Reset cause: POR
Model: Engicam Is.IoT MX6UL Starterkit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
isiotmx6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2017-03-17 09:27:08 +01:00
Peng Fan
77fa04577a imx: imx7ulp: add EVK board support
Add EVK board support.
Add the evk dts file.

LOG:
U-Boot 2017.03-rc2-00038-gab86c1d (Feb 22 2017 - 15:59:58 +0800)

CPU:   Freescale i.MX7ULP rev1.0 at 500 MHz
Reset cause: POR
Boot mode: Dual boot
Model: NXP i.MX7ULP EVK
DRAM:  1 GiB
MMC:   FSL_SDHC: 0
In:    serial@402D0000
Out:   serial@402D0000
Err:   serial@402D0000
Net:   Net Initialization Skipped
No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
27117b2024 mx7ulp: Add HAB boot support
Add CAAM clock functions, SEC_CONFIG[1] fuse checking, and default CSF
size for HAB support boot on mx7ulp.

Users need to uncomment the CONFIG_SECURE_BOOT in mx7ulp_evk.h to build
secure uboot.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
c40d612b1a serial: lpuart: restructure lpuart driver
Drop CONFIG_LPUART_32B_REG.
Move the register structure to a common file include/fsl_lpuart.h
Define lpuart_serial_platdata structure which includes the reg base and flags.
For 32Bit register access, use lpuart_read32/lpuart_write32 which handles
big/little endian.
For 8Bit register access, still use the orignal code.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Cc: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Shaohui Xie <Shaohui.Xie@nxp.com>
Cc: Alison Wang <b18965@freescale.com>
2017-03-17 09:27:08 +01:00
Ye Li
d4dcee2213 imx: mx7ulp: Implement the clock functions for i2c driver
Implement the i2c clock enable and get function for mx7ulp. These
functions are required by imx_lpi2c driver.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
1b409828b1 imx: mx7ulp: Add soc level initialization codes and functions
Implement soc level functions to get cpu rev, reset cause, enable cache,
etc. We will disable the wdog and init clocks in s_init at very early u-boot
phase.

Since the we are seeking the way to get chip id for mx7ulp, the get_cpu_rev
is hard coded to a fixed value. This may change in future.

Reuse some code in imx-common.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
d0f8516d9e imx: mx7ulp: Add clock framework and functions
Add a clock framework to support SCG1/PCC2/PCC3 for A7 to support get/set
clock source, divider, clock rate and parent source.
Users need to include pcc.h to use the APIs to for peripherals clock. Each
peripheral clock is defined in enum pcc_clk type.

SCG relevants APIs are defined in scg.h which supports clock rate get, PLL/PFD
enablement and settings, and all SCG clock initialization. User need use enum
scg_clk to access each clock source.

In clock.c, we initialize necessary clocks at u-boot s_init and implement the
clock functions used by driver modules to operate clocks dynamically.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
0cb3d82c68 imx: mx7ulp: add iomux driver to support IOMUXC0 and IOMUXC1
Add a new driver under ULP directory to support its IOMUXC
controllers. The ULP has two IOMUXC, the IOMUXC0 is used
for M4 domain, while IOMUXC1 is for A7. We set IOMUXC1 as
the default IOMUX in this driver. Any pins in IOMUXC0 needs
to configure with IOMUX_CONFIG_MPORTS in its mux_mode field.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Peng Fan
e90a08daee imx: mx7ulp: Add mx7ulp to Kconfig
i.MX7ULP is a new series SoC which has different architecture
from previous i.MX platforms. Create a new cpu folder for it,
and add it to Kconfig.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
2017-03-17 09:27:08 +01:00
Siarhei Siamashka
19a75b8cf8 arm: omap3: Bring back ARM errata workaround 725233
The workaround for ARM errata 725233 had been lost since
commit 45bf05854b (armv7: adapt omap3 to the new cache
maintenance framework). Bring it back in order to avoid
very difficult to reproduce, but actually encountered in
the wild CPU deadlocks when running software rendered
X11 desktop on OMAP3530 hardware.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Migrate to Kconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-14 20:40:17 -04:00
Tom Rini
8dda2e2f9e ARM: Migrate errata to Kconfig
This moves all of the current ARM errata from various header files and in to
Kconfig.  This allows for a minor amount of cleanup as we had some instances
where both a general common header file was enabling errata as well as the
board config.  We now just select these once at the higher level in Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>
2017-03-09 19:52:50 -05:00
Masahiro Yamada
e856bdcfb4 flash: complete CONFIG_SYS_NO_FLASH move with renaming
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.

During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH".  Flipping the logic will
make the code more readable.  Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.

This commit was created as follows:

[1] Edit "default n" to "default y" in the config entry in
    common/Kconfig.

[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"

[3] Rename the instances in defconfigs by the following:
  find . -path './configs/*_defconfig' | xargs sed -i \
  -e '/CONFIG_SYS_NO_FLASH=y/d' \
  -e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'

[4] Change the conditionals by the following:
  find . -name '*.[ch]' | xargs sed -i \
  -e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
  -e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
  -e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
  -e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'

[5] Modify the following manually
  - Rename the rest of instances
  - Remove the description from README
  - Create the new Kconfig entry in drivers/mtd/Kconfig
  - Remove the old Kconfig entry from common/Kconfig
  - Remove the garbage comments from include/configs/*.h

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
2017-02-12 14:30:25 -05:00
Tom Rini
c83a824e62 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	configs/ls1046aqds_defconfig
	configs/ls1046aqds_nand_defconfig
	configs/ls1046aqds_qspi_defconfig
	configs/ls1046aqds_sdcard_ifc_defconfig
	configs/ls1046aqds_sdcard_qspi_defconfig
	configs/ls1046ardb_emmc_defconfig
	configs/ls1046ardb_qspi_defconfig
	configs/ls1046ardb_sdcard_defconfig
2017-02-03 20:33:42 -05:00
Prabhakar Kushwaha
8e63ed518d arch: arm: update the IFC IP input clock
IFC IP clock is always a constant divisor of platform clock
pre-defined per SoC. Clock control register (CCR) used in
current implementation governs IFC IP output clock.

Update sys_info->freq_localbus to represent IFC input clock with
value constant divisor of platform clock.

Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-02-03 14:31:19 -08:00
Lukasz Majewski
11bd5e7b62 BOARD: MCCMON6: Provide support for iMX6q based mccmon6 board
This patch provides u-boot support for Liebherr (LWN) mccmon6 board.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-30 16:24:47 +01:00
Marcin Niestroj
d4b1b52737 ARM: imx6ul: Move liteSOM source to SoC directory
Moving arch/arm/mach-litesom/ to arch/arm/cpu/armv7/mx6/ was requested
in [1] during discussion of chiliSOM support patches.

[1] http://lists.denx.de/pipermail/u-boot/2017-January/279137.html

Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2017-01-27 10:48:07 +01:00
Simon Glass
a5d67547dd Convert CONFIG_BOARD_EARLY_INIT_F to Kconfig
This converts the following to Kconfig:
   CONFIG_BOARD_EARLY_INIT_F

Signed-off-by: Simon Glass <sjg@chromium.org>
2017-01-25 17:38:32 -05:00
Tom Rini
e5ec48152a Kconfig: Migrate BOARD_LATE_INIT to a select
This option should not really be user selectable.  Note that on PowerPC
we currently only need BOARD_LATE_INIT when CHAIN_OF_TRUST is enabled so be
conditional on that.

Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com> (for UniPhier)
2017-01-24 10:35:54 -05:00
Hou Zhiqiang
19538f306b kconfig: move FSL_PCIE_COMPAT to platform Kconfig
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: York Sun <york.sun@nxp.com>
2017-01-18 09:27:18 -08:00
York Sun
66e399b68d ddr: fsl: Move macro CONFIG_NUM_DDR_CONTROLLERS to Kconfig
Use option NUM_DDR_CONTROLLERS in ddr Kconfig and clean up existing
usage in ls102xa and fsl-layerscape. Remove all powerpc macros in
config header and board header files.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:49 -05:00
York Sun
ba1b6fb5cc arm: layerscape: Move CONFIG_SYS_FSL_ERRATUM_* to Kconfig
Use Kconfig to select errata workaround.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:42 -05:00
York Sun
d26e34c4c4 fsl_ddr: Move DDR config options to driver Kconfig
Create driver/ddr/fsl/Kconfig and move existing options. Clean up
existing macros.

Signed-off-by: York Sun <york.sun@nxp.com>
[trini: Migrate sbc8641d, xpedite537x and MPC8536DS, run a moveconfig.py -s]
Signed-off-by: Tom Rini <trini@konsulko.com>
2017-01-04 19:40:41 -05:00
York Sun
90b80386ff crypto: Move CONFIG_SYS_FSL_SEC_LE and _BE to Kconfig
Use Kconfig option to set little- or big-endian access to secure
boot and trust architecture.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:19 -05:00
York Sun
2c2e2c9e14 crypto: Move SYS_FSL_SEC_COMPAT into driver Kconfig
Instead of define CONFIG_SYS_FSL_SEC_COMPAT in header files for PowerPC
and ARM SoCs, move it to Kconfig under the driver.

Signed-off-by: York Sun <york.sun@nxp.com>
2017-01-04 19:40:17 -05:00
Jagan Teki
854bb75be9 imx6: icorem6_rqs: Add FEC support
Add FEC support for Engicam i.CoreM6 RQS modules.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:06 +01:00
Jagan Teki
bd363f80e4 imx6: geam6ul: Add FEC support
Add FEC support for Engicam GEAM6UL module.

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:05 +01:00
Jagan Teki
dca7c2878a imx6: icorem6_rqs: Add I2C support
Add I2C support for Engicam i.CoreM6 RQS modules.

icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl-rqs> i2c dev 0
Setting bus to 0
icorem6qdl-rqs> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl-rqs> i2c probe
Valid chip addresses: 4F
icorem6qdl-rqs> i2c md 4F 0xff
00ff: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff    ................
icorem6qdl-rqs> i2c bus
Bus 0:  i2c@021a0000  (active 0)
   4f: generic_4f, offset len 1, flags 0
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 18:39:05 +01:00
Jagan Teki
871ec6da42 arm: imx6q: Add Engicam i.CoreM6 Quad/Dual RQS Starter Kit initial support
Boot from MMC:
-------------
U-Boot SPL 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44)
Trying to boot from MMC1

U-Boot 2016.11-rc2-g217bd8e-dirty (Nov 08 2016 - 22:59:44 +0530)

CPU:   Freescale i.MX6D rev1.2 at 792 MHz
Reset cause: POR
Model: Engicam i.CoreM6 Quad/Dual RQS Starter Kit
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl-rqs>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
d31373c4ac imx6: geam6ul: Add I2C support
Add I2C support for Engicam GEAM6UL module.

geam6ul> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
geam6ul> i2c dev 0
Setting bus to 0
geam6ul> i2c dev
Current bus is 0
geam6ul> i2c speed 100000
Setting bus speed to 100000 Hz
geam6ul> i2c probe
Valid chip addresses: 2C
geam6ul> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
a5b9f8c8f0 arm: imx6ul: Add Engicam GEAM6UL Starter Kit initial support
Boot Log:
--------
U-Boot SPL 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30)
Trying to boot from MMC1

U-Boot 2016.11-rc2-00144-g922adaa-dirty (Oct 28 2016 - 18:55:30 +0530)

CPU:   Freescale i.MX6UL rev1.1 528 MHz (running at 396 MHz)
CPU:   Industrial temperature grade (-40C to 105C) at 43C
Reset cause: POR
Model: Engicam GEAM6UL
DRAM:  128 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
geam6ul>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:16:10 +01:00
Jagan Teki
d90384e834 imx6: icorem6: Add I2C support
Add I2C support for Engicam i.CoreM6 qdl board.

icorem6qdl> i2c bus
Bus 0:  i2c@021a0000
Bus 1:  i2c@021a4000
Bus 2:  i2c@021a8000
icorem6qdl> i2c dev 2
Setting bus to 2
icorem6qdl> i2c speed 100000
Setting bus speed to 100000 Hz
icorem6qdl> i2c probe
Valid chip addresses: 2C
icorem6qdl> i2c md 2C 0xff
00ff: 00 00 00 00 0f f0 01 64 ff ff 00 00 00 00 00 00    .......d........

Cc: Stefano Babic <sbabic@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Heiko Schocher <hs@denx.de>
2016-12-16 17:15:27 +01:00
Jagan Teki
e920f60779 icorem6: Use CONFIG_DM_ETH support
Use CONFIG_DM_ETH and remove board_eth_init code
from board files.

Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-12-16 17:15:27 +01:00
Patrick Bruenn
98d62e618b arm: imx: add i.MX53 Beckhoff CX9020 Embedded PC
Add CX9020 board based on mx53loco.
Add simplified imx53 base device tree from kernel v4.8-rc8, to reuse
serial_mxc with DTE and prepare for device tree migration of other
functions and imx53 devices.

The CX9020 differs from i.MX53 Quick Start Board by:
- use uart2 instead of uart1
- DVI-D connector instead of VGA
- no audio
- CCAT FPGA connected to emi
- enable rtc

Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
2016-12-16 12:57:12 +01:00
Peng Fan
47f73504d8 arm: imx: add i.MX6SLL EVK board support
Add i.MX6SLL EVK board support.
1. Add imx6sll-evk device tree.
2. Enable SDHC/I2C/UART.
3. Enable REGULATOR/PMIC/I2C/GPIO/SDHC/PINCTRL driver.

Boot Log:
U-Boot 2016.11-00127-gc635871-dirty (Nov 24 2016 - 13:28:19 +0800)

CPU:   Freescale i.MX6SLL rev1.0 at 792MHz
CPU:   Commercial temperature grade (0C to 95C)Reset cause: POR
Model: Freescale i.MX6SLL EVK Board
Board: MX6SLL EVK
DRAM:  2 GiB
i2c bus 0 at 35258368, no gpio pinctrl state.
PMIC: PFUZE100! DEV_ID=0x10 REV_ID=0x21
MMC:   FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
2cc021697b imx: mx6sll: add Kconfig entry for i.MX6SLL
add Kconfig entry for i.MX6SLL

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16 11:38:24 +01:00
Peng Fan
dfca246f4c imx: mx6sll: add clock support
Add clock support for i.MX6SLL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
708f692753 imx: clock: gate clk before changing pix clk mux
The LCDIF Pixel clock mux is not glitchless, so need
to gate before changing mux.

Also change enable_lcdif_clock prototype with a new input
parameter to indicate disable or enable.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
e332623b03 imx: mx6sl: add lcdif clock support
Add lcdif clock support for i.MX6SL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2016-12-16 11:38:24 +01:00
Peng Fan
70ac169723 imx: mx6: lcdif: gate clock before changing mux
The mux for the lcd clock is not glitchless,
so need to first gate the clock before changing the mux.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Peng Fan
0e81982de0 imx: mx6: fix mmdc ch0 clk for 6SL
>From RM, per_periph2_clk_sel option3 is:
"derive clock from 198MHz clock (divided 392MHz PLL2 PFD)."

So fix it.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-12-16 11:38:24 +01:00
Marcin Niestroj
c9e40e65e1 board/liteboard: Add support for liteBoard
liteBoard is a development board which uses liteSOM as its base.

Hardware specification:
 * liteSOM (i.MX6UL, DRAM, eMMC)
 * Ethernet PHY (id 0)
 * USB host (usb_otg1)
 * MicroSD slot (uSDHC1)

Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
2016-12-16 10:31:13 +01:00
Breno Lima
0719b16f19 udoo_neo: Add thermal support
Add thermal support on the Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 10:21:25 +01:00
Breno Lima
4a056c4504 udoo_neo: Move MX6SX configuration to Kconfig
It's not necessary to define the processor in the defconfig file.

The preferred method to select the SoC is via Kconfig file.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-12-16 10:20:10 +01:00
Max Krummenacher
a02d517b01 arm: imx: initial support for colibri imx6
This adds board support for the Toradex module family Colibri iMX6.
The familiy consists of a module with i.MX6 DualLite, i.MX6 Solo, both
with a version for commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:03:43 +01:00
Max Krummenacher
592f4aed6d arm: imx: initial support for apalis imx6
This adds board support for the Toradex module family Apalis iMX6.
The familiy consists of a module with i.MX6 Dual, i.MX6 Quad with
commercial and industrial temperature range.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
2016-12-16 10:02:45 +01:00
Patrick Delaunay
91558c8153 arm: armv7: add us timer for bootstage
solve issue when bootstage is used with armV7 generic timer
first call of timer_get_boot_us() use the function get_timer()
before timer initialization (arch.timer_rate_hz = 0)
=> div by 0

Commit-notes

When I activate bootstage on ARMV7 architecture with platform
using the generic armv7 timer defined in file
./arch/arm/cpu/armv7m/timer.c

I have a issue because gd->arch.timer_rate_hz = 0

For me the get_timer() function should not used before timer_init
(which initialize gd->arch.timer_rate_hz) at least for the ARMV7
timer.

But in the init sequence, the first bootstage fucntion is called
before timer_init and this function use the timer function.

For me it is a error in the generic init sequence :
mark_bootstage is called before timer_init.

static init_fnc_t init_sequence_f[] = {
....
    arch_cpu_init_dm,
    mark_bootstage,        /* need timer, go after init dm */
...
#if defined(CONFIG_ARM) || defined(CONFIG_MIPS) || \
        defined(CONFIG_BLACKFIN) || defined(CONFIG_NDS32) || \
        defined(CONFIG_SPARC)
    timer_init,        /* initialize timer */
#endif
.......

To solve the issue for all the paltform, we can move timer_init()
call just before mark_bootstage() in this array...

It should be ok for ARMV7 but I don't sure for other platform
impacted
- the other ARM platform or ARMV7 wich don't use generic timer
- MIPS BLACKFIN NDS32 or SPARC

and I don't sure of impact for other function called
(board_early_init_f for example....)

=> This patch solve issue only in timer armv7
   get_boot_us() can be called everytime without div by 0 issue
   (gd->arch.timer_rate_hz is not used)

END

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>
2016-12-09 08:39:10 -05:00
Tom Rini
194eded14c Merge git://git.denx.de/u-boot-mpc85xx 2016-12-04 13:55:15 -05:00
York Sun
72ccd31e64 armv7: ls1021a: Move SECURE_BOOT option to Kconfig
Move from CONFIG_SYS_EXTRA_OPTIONS to Kconfig option.

Signed-off-by: York Sun <york.sun@nxp.com>
2016-12-02 12:38:41 -08:00
Tom Rini
4d6647ab17 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-11-30 09:57:52 -05:00
Lukasz Majewski
4db4d42ee2 imx6: clock: Enable External Memory Interface [EIM] clock (eim_slow_clock)
This patch extends the imx6 clock code to enable or disable the EIM
slow clock, which in necessary when one wants to use EIM interface t
o read/write from external memory (e.g. NOR).

Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
2016-11-30 09:57:19 +01:00
Christoph Fritz
730d25443a mx6sx: Add initial support for Samtec VIN|ING 2000 board
This patch adds initial support for Samtec VIN|ING 2000 board.

Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
2016-11-30 09:54:42 +01:00
Breno Lima
792f186846 mx6sx: Add initial support for UDOO Neo Board
UDOO Neo Board is a development board from Seco that has three models:
 - UDOO Neo Basic
 - UDOO Neo Basic Kick Starter
 - UDOO Neo Extended
 - UDOO Neo Full

All versions are based on the i.MX6 SoloX processor.

For more details about the UDOO Neo board, please refer to:
http://www.udoo.org/udoo-neo/

This work is based on a previous commit of Francesco Montefoschi
<francesco.monte@gmail.com>:
877b71184a

Only tested on the UDOO Neo Full board.

Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2016-11-29 16:48:20 +01:00
Eric Nelson
a425bf7281 ARM: mx6: ddr: use Kconfig for inclusion of DDR calibration routines
The DDR calibration routines are gated by conditionals for the
i.MX6DQ SOCs, but with the use of the sysinfo parameter, these
are usable on at least i.MX6SDL and i.MX6SL variants with DDR3.

Also, since only the Novena board currently uses the dynamic
DDR calibration routines, these routines waste space on other
boards using SPL.

Add a KConfig entry to allow boards to selectively include the
DDR calibration routines.

Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-29 16:40:37 +01:00
Eric Nelson
48c7d4379b mx6: ddr: add routine to return DDR calibration data
Add routine mmdc_read_calibration() to return the output of DDR
calibration. This can be used for debugging or to aid in construction
of static memory configuration.

This routine will be used in a subsequent patch set adding a virtual
"mx6memcal" board, but could also be useful when gathering statistics
during an initial production run.

Signed-off-by: Eric Nelson <eric@nelint.com>
2016-11-29 16:40:25 +01:00
Eric Nelson
7f17fb7400 mx6: ddr: pass mx6_ddr_sysinfo to calibration routines
The DDR calibration routines have scattered support for bus
widths other than 64-bits:

-- The mmdc_do_write_level_calibration() routine assumes the
presence of PHY1, and
-- The mmdc_do_dqs_calibration() routine tries to determine
whether one or two DDR PHYs are active by reading MDCTL.

Since a caller of these routines must have a valid struct mx6_ddr_sysinfo
for use in calling mx6_dram_cfg(), and the bus width is available in the
"dsize" field, use this structure to inform the calibration routines which
PHYs are active.

This allows the use of the DDR calibration routines on CPU variants
like i.MX6SL that only have a single MMDC port.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-11-29 16:40:12 +01:00
Eric Nelson
b33f74ead4 mx6: ddr: allow 32 cycles for DQS gating calibration
The DDR calibration code is only setting flag DG_CMP_CYC (DQS gating sample
cycle) for the first PHY.

Set the 32-cycle flag for both PHYs and clear when done so the MPDGCTRL0
output value isn't polluted with calibration artifacts.

Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Marek Vasut <marex@denx.de>
2016-11-29 16:39:58 +01:00
Stefano Babic
2d221489df Merge branch 'master' of git://git.denx.de/u-boot
Signed-off-by: Stefano Babic <sbabic@denx.de>
2016-11-29 16:28:28 +01:00
Peng Fan
fea7452c15 armv7: psci: cpu_off: flush D-Cache before disable D-Cache
Before disable cache, need to first flush cache.

There maybe dirty data in D-Cache before disable D-Cache.
After disable D-Cache, the first store instructions in
psci_v7_flush_dcache_all will directly store registers
{r4-r5, r7, r9-r11, lr} to memory.
If there is dirty data before disable D-Cache,
psci_v7_flush_dcache_all will flush data to memory,
and may overwrite the memory that hold the registers
{r4-r5, r7, r9-r11, lr}.

So before disable cache, first flush D-Cache.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Hongbo Zhang <hongbo.zhang@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Tom Rini <trini@konsulko.com>
2016-11-29 08:15:31 -05:00
Tom Rini
983e37007d arm: Introduce arch/arm/mach-omap2 for OMAP2 derivative platforms
This moves what was in arch/arm/cpu/armv7/omap-common in to
arch/arm/mach-omap2 and moves
arch/arm/cpu/armv7/{am33xx,omap3,omap4,omap5} in to arch/arm/mach-omap2
as subdirectories.  All refernces to the former locations are updated to
the current locations.  For the logic to decide what our outputs are,
consolidate the tests into a single config.mk rather than including 4.

Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 14:07:29 -05:00
Lokesh Vutla
140d76a9ee board: ti: amx3xx: Remove multiple EEPROM reads
Detect the board very early and avoid reading eeprom multiple times.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:59:25 -05:00
Lokesh Vutla
b64a7cb92d ARM: AMx3xx: Centralize early clock initialization
This is similar to Commit 93e6253d11 ("ARM: OMAP4/5: Centralize
early clock initialization") that was done for OMAP4+, reflecting the same
for AM33xx and AM43xx SoCs to centralize clock initialization.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Add setup_early_clocks that calls setup_clocks_for_console for
        ti81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
2016-11-21 13:58:55 -05:00
Lokesh Vutla
c704a99dff ARM: AMx3xx: Allow arch specific code to use early DM
Early system initialization is being done before initf_dm is being called
in U-Boot. Then system will fail to boot if any of the DM enabled driver
is being called in this system initialization code. So, rearrange the
code a bit so that DM enabled drivers can be called during early system
initialization. This is inspired by commit e850ed82bc ("ARM: OMAP4+: Allow
arch specific code to use early DM")

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-11-21 09:49:58 -05:00
Peng Fan
97c16dc8bf imx: mx6ull: update the REFTOP_VBGADJ setting
According to design team, we need to set REFTOP_VBGADJ
in PMU MISC0 according to the REFTOP_TRIM[2:0] fuse. the
actually table is as below:

  '000" - set REFTOP_VBGADJ[2:0] to 3'b000
  '001" - set REFTOP_VBGADJ[2:0] to 3'b001
  '010" - set REFTOP_VBGADJ[2:0] to 3'b010
  '011" - set REFTOP_VBGADJ[2:0] to 3'b011
  '100" - set REFTOP_VBGADJ[2:0] to 3'b100
  '101" - set REFTOP_VBGADJ[2:0] to 3'b101
  '110" - set REFTOP_VBGADJ[2:0] to 3'b110
  '111" - set REFTOP_VBGADJ[2:0] to 3'b111

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
2016-11-16 20:53:55 +01:00
Ye.Li
27e3a3c7f8 imx: mx6sx: Disable ENET clock before switching clock parent
Need to gate ENET clock when switching to a new clock parent, because
the mux is not glitchless.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye.Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-11-16 20:53:55 +01:00
Jagan Teki
aec9a0f19f sunxi: Rename CONFIG_SUNXI to CONFIG_ARCH_SUNXI
CONFIG_SUNXI -> CONFIG_ARCH_SUNXI
and removed CONFIG_SUNIX from config_whitelist.txt

Cc: Simon Glass <sjg@chromium.org>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-10-30 11:38:04 +01:00
Jagan Teki
f160c5c8b9 engicam: icorem6: Add DM_GPIO, DM_MMC support
Add DM_GPIO, DM_MMC support for u-boot and disable for SPL.

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Jagan Teki
e88edc7b4a arm: imx6q: Add devicetree support for Engicam i.CoreM6 DualLite/Solo
i.CoreM6 DualLite/Solo modules are system on module solutions
manufactured by Engicam with following characteristics:
CPU           NXP i.MX6 DL, 800MHz
RAM           1GB, 32, 64 bit, DDR3-800/1066
NAND          SLC,512MB
Power supply  Single 5V
MAX LCD RES   FULLHD

and more info at
http://www.engicam.com/en/products/embedded/som/sodimm/i-core-m6s-dl-d-q

Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Jagan Teki
f4b7532f82 arm: imx: Add Engicam i.CoreM6 QDL Starter Kit initial support
Boot Log for i.CoreM6 DualLite/Solo Starter Kit:
-----------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6SOLO rev1.3 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 31C
Reset cause: POR
DRAM:  256 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
switch to partitions #0, OK
mmc0 is current device
reading boot.scr
** Unable to read file boot.scr **
reading zImage
6741808 bytes read in 341 ms (18.9 MiB/s)
Booting from mmc ...
reading imx6dl-icore.dtb
30600 bytes read in 19 ms (1.5 MiB/s)
   Booting using the fdt blob at 0x18000000
   Using Device Tree in place at 18000000, end 1800a787

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0

Boot Log for i.CoreM6 Quad/Dual Starter Kit:
--------------------------------------------

U-Boot SPL 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46)
Trying to boot from MMC1

U-Boot 2016.09-rc2-30739-gd1fa290 (Sep 17 2016 - 00:37:46 +0530)

CPU:   Freescale i.MX6Q rev1.2 at 792MHz
CPU:   Industrial temperature grade (-40C to 105C) at 28C
Reset cause: POR
DRAM:  512 MiB
MMC:   FSL_SDHC: 0
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
icorem6qdl>

Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
2016-10-26 16:53:16 +02:00
Tom Rini
711b534120 Merge git://git.denx.de/u-boot-fsl-qoriq
Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
	include/configs/ls1021aqds.h
	include/configs/ls1021atwr.h
2016-10-12 08:29:42 -04:00
Tom Rini
f5fd45ff64 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2016-10-08 09:33:37 -04:00
Lokesh Vutla
1f95770807 ARM: AM437X: Add Silicon ID support
Add silicon ID code for AM437x silicon. This can be used to print
the cpu info using CONFIG_DISPLAY_CPUINFO.
Also printing "CPU :" along with cpu name in order to be consistent
with other OMAP platforms.

Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2016-10-08 09:33:36 -04:00
Stefan Agner
d7255e8ddb ARM: vf610: use strcpy for soc environment variable
To create the soc environment variable we concatenate two strings
on the stack. So far, strcat has been used for the first string as
well as for the second string. Since the variable on the stack is
not initialized, the first strcat may not start using the first
entry in the character array. This then could lead to an buffer
overflow on the stack.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2016-10-07 15:56:52 +02:00
Keerthy
1dbc40e7d2 ARM: OMAP5+: Override switch_to_hypervisor function
Override the switch_to_hypervisor function to switch cpu to hypervisor
mode using the available ROM code hook early in the boot phase before
the boot loader checks for HYP mode.

Based on the work done by Jonathan Bergsagel jbergsagel@ti.com.

Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:58:16 -04:00
Keerthy
d31d4a2d75 ARM: Introduce function to switch to hypervisor mode
On some of the SoCs one cannot enable hypervisor mode directly from the
u-boot because the ROM code puts the chip to supervisor mode after it
jumps to boot loader. Hence introduce a weak function which can be
overridden based on the SoC type and switch to hypervisor mode in a
custom way.

Cc: beagleboard-x15@googlegroups.com
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:58:16 -04:00
Keerthy
859c70df23 omap: Set appropriate cache configuration for LPAE and non-LAPE cases
Cache configuration methods is different for LPAE and non-LPAE cases.
Hence the bits and the interpretaion is different for two cases.
In case of non-LPAE mode short descriptor format is used and we need
to set Cache and Buffer bits.

In the case of LPAE the cache configuration happens via MAIR0 lookup.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:57:44 -04:00
Keerthy
c268a9bde0 omap: Remove hardcoding of mmu section shift to 20
As of now the mmu section shift is hardcoded to 20 but with LPAE
coming into picture this can be different. Hence replacing 20 with
MMU_SECTION_SHIFT macro.

Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 20:57:43 -04:00
Siarhei Siamashka
22a402f00c ARM: Respect CONFIG_SPL_STACK define in lowlevel_init.S
The SPL and U-Boot proper may use different initial stack
locations, which are configured via CONFIG_SPL_STACK and
CONFIG_SYS_INIT_SP_ADDR defines. The lowlevel_init.S
code needs to handle this in the same way as crt0.S

Without this fix, setting the U-Boot stack location to some
place, which is not safely accessible by the SPL (such as
the DRAM), causes a very early SPL deadlock.

Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 20:57:36 -04:00
Simon Glass
a807ab3303 spl: Kconfig: Move SPL_DISPLAY_PRINT to Kconfig
Move this option to Kconfig and tidy up existing uses. Also add a function
comment to the header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-10-06 14:48:21 -04:00
York Sun
53d76829d5 armv7: ls1021a: Move DDR config options to Kconfig
Move DDR3, DDR4 and related config options to Kconfig and clean up
existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:11 -07:00
York Sun
f534b8f5fd arm: Move SYS_FSL_SRDS_* and SYS_HAS_SERDES to Kconfig
Move these options to Kconfig and clean up existing uses.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:11 -07:00
York Sun
25af7dc193 arm: Move SYS_FSL_IFC_BANK_COUNT to Kconfig
Move this option to Kconfig and clean up existing uses.
This option is also used by PowerPC SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:11 -07:00
York Sun
b4b60d06c6 arm: Move MAX_CPUS to Kconfig
Move MAX_CPUS option to Kconfig and clean up existing uses for ARM. This
option is used by Freescale Layerscape SoCs.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
York Sun
fb2bf8c2c6 arm: Move FSL_LSCH2 FSL_LSCH3 to Kconfig
Move these options to Kconfig and create a sub-menu to avoid name
conflict with other architectures.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
York Sun
4a4441765d arm: Fix Kconfig for proper display menu
Some config options should not have prompt. They are selected by choosing
target.

Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2016-10-06 09:59:10 -07:00
Xiaoliang Yang
f85a8e8d1d armv7: LS1021a: enable i-cache in start.S
Delete CONFIG_SKIP_LOWLEVEL_INIT define in ls1021atwr.h and
ls1021aqds.h can let it run cpu_init_cp15 to enable i-cache. First
stage of u-boot can run faster after that. There is a description
about skip lowlevel init in board/freescale/ls1021atwr/README.

Signed-off-by: Xiaoliang Yang <xiaoliang.yang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
2016-10-06 09:55:08 -07:00
Albert ARIBAUD \(3ADEV\)
ed0c2c0a9e tools: mkimage: add support for Vybrid image format
This format can be flashed directly at address 0 of
the NAND FLASH, as it contains all necessary headers.

Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
2016-10-06 09:06:16 +02:00
Peng Fan
f15ece388f imx: imx6ul: disable POR_B internal pull up
>From TO1.1, SNVS adds internal pull up control for POR_B,
the register filed is GPBIT[1:0], after system boot up,
it can be set to 2b'01 to disable internal pull up.
It can save about 30uA power in SNVS mode.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 19:37:39 +02:00
Stefan Agner
81c4eccb55 imx: mx6: fix USB bmode to use reserved value
Currently the bmode "usb" uses BOOT_CFG1 to 0x01, -which means
BOOT_CFG1[7:4] is set to b0000. According to Table 8-7 Boot
Device Selection this is NOR/OneNAND and not Reserved.

Use 0x10 which leads to b0001, which is a Reserved boot device.
With that the SoC reliably falls back to the serial loader.

Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Tested-by: Troy Kisky <troy.kisky@boundarydevices.com>
2016-10-04 19:31:23 +02:00
Peng Fan
55a42b33f2 arm: imx: add i.MX6ULL 14x14 EVK board support
Add i.MX6ULL EVK board support:
Add device tree file, which is copied from NXP Linux.
Enabled DM_MMC, DM_GPIO, DM_I2C, DM_SPI, PINCTRL, DM_REGULATOR.
The uart iomux settings are still keeped in board file.

Boot Log:
U-Boot 2016.09-rc1-00366-gbb419ef-dirty (Aug 11 2016 - 13:08:58 +0800)

CPU:   Freescale i.MX6ULL rev1.0 at 396MHz
CPU:   Commercial temperature grade (0C to 95C) at 15C
Reset cause: POR
Model: Freescale i.MX6 ULL 14x14 EVK Board
Board: MX6ULL 14x14 EVK
DRAM:  512 MiB
MMC:   initialized IMX pinctrl driver
FSL_SDHC: 0, FSL_SDHC: 1
In:    serial
Out:   serial
Err:   serial
Net:   CPU Net Initialization Failed
No ethernet found.
Hit any key to stop autoboot:  0
=> mmc dev 1
switch to partitions #0, OK
mmc1 is current device

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:42:07 +02:00
Peng Fan
5b66482d44 imx: imx6ull: adjust the ldo 1.2v bandgap voltage
Per to design team, on i.MX6UL, the LDO 1.2V bandgap voltage
is 30mV higher, so we need to adjust the REFTOP_VBGADJ(anatop
MISC0 bit[6:4]) setting to 2b'110.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:01 +02:00
Peng Fan
3974b7f6e0 imx: mx6ull: update clock settings and CCM register map
Update Clock settings and CCM register map for i.MX6ULL.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2016-10-04 15:41:00 +02:00