clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZSjvwAAKCRDKSWXLKUoM
IR34AJ92oum3pJXKxKREEZh0dCfDvJlE/wCggyzxI2T5liJfRG5jzlUuDjiLLU0=
=u1bz
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2024.01-rc1-v3' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2024.01-rc1 v3
clk:
- remove additional compatible strings for Versal NET
net:
- zynq_gem: Fix clock calculation for MDC for higher frequencies
pinctrl:
- core: Extend pinmux status buffere size
- zynqmp driver: Show also tristate configuration
test:
- add test case for pxe get
Xilinx:
- describe SelectMAP boot mode
Zynq:
- Fix nand description in DT
ZynqMP:
- DTS sync patches with kernel and also W=1 related fixes
- Add support for KD240, zcu670, e-a2197 with x-prc cards, SC revB/C with i2c
description for other SC based boards
- k24 psu_init cleanup
AVS driver needs to be notified before or after clock change,
depending upon new rate is greater or less than current clock rate.
Fixes: 1e0aa873bc7cd ("clk: clk-ti-sci: Notify AVS driver upon setting clock rate")
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
AVS is enabled at R5 SPL stage, on few platforms like J721E
and J7200 clk-k3 is used instead if clk-sci driver.
Add support in clk-k3 driver as well to notify AVS driver
on setting clock rate so that voltage is changed accordingly.
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
This partially reverts commit ff33227819.
Versal NET clock node should use "xlnx,versal-net-clk", "xlnx,versal-clk"
compatible string that's why it is not necessary to define Versal NET
specific compatible string if there is no any other change needed. It can
be get back if there is a need to differentiate clock support between
Versal and Versal NET.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c09276022db5f1b150679cc7a9f9583363ace2fb.1695808971.git.michal.simek@amd.com
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
-----BEGIN PGP SIGNATURE-----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=1mUx
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20231004' of https://source.denx.de/u-boot/custodians/u-boot-stm
STM32 MCU:
_ alignment with kernel DT v6.5 for stm32f429 and stm32f746
_ rework way of displaying ST logo for stm32f746-disco and stm32f769-disco
STM32 MPU:
_ alignment with kernel DT v6.6-rc1
_ add RNG support for stm32mp13
_ add USB, USB boot and stm32prog command support for stm32mp13
_ add support of USART1 clock for stm32mp1
_ only print RAM and board code with SPL_DISPLAY_PRINT flag for
stm32mp1
_ rename update_sf to dh_update_sd_to_sf and add dh_update_sd_to_emmc
for stm32mp15xx DHCOR
[ Fix merge conflict at board/st/common/stm32mp_dfu.c ]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add USART1 clock parents and mux configuration. This allows
support for configuring the USART1 as the serial console in
SPL and U-Boot via device tree. Without this patch the SPL
with usart1 serial console enabled crashes because it can
not find the clock specified in the device tree for usart1.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Synchronize R8A774E1 RZ/G2H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774C0 RZ/G2E clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774B1 RZ/G2N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R8A774A1 RZ/G2M clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A779G0 V4H clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
The PLL2_VAR is not implemented yet and PLL2 is still configured
as regular PLL2 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A77960 M3-W and R8A77961 M3-W+ clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Synchronize R-Car R8A7791 M2-W and R8A7793 M2-N clock tables with Linux 6.5.3,
commit 238589d0f7b421aae18c5704dc931595019fa6c7 .
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Arrays are not cleared entirely because ARRAY_SIZE
returns the number of elements in an array, not the size
in bytes.
This commit fixes the calls to memset by providing the
array size in bytes instead of the number of elements
in the array.
Signed-off-by: Francois Berder <fberder@outlook.fr>
This old patch was marked as deferred. Bring it back to life, to continue
towards the removal of common.h
Move this out of the common header and include it only where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
For reference clocks, PM_CLK_GET_PARENT call is not allowed.
PM_CLK_GET_PARENT only allowed for MUX clocks. Rename the
versal_clock_ref() with versal_clock_get_ref_rate() for better
readability. Fix the versal_clock_get_ref_rate function by
passing the parent_id, and check whether the parent_id
belongs to ref_clk or pl_alt_ref_clk.
Also adding the function versal_clock_get_fixed_factor_rate()
if the clk_id belongs to the fixed factor clock.
Signed-off-by: Venkatesh Yadav Abbarapu <venkatesh.abbarapu@amd.com>
Link: https://lore.kernel.org/r/20230912033055.2549-1-venkatesh.abbarapu@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
There is a chance that assigned-clock-rates is given and assigned-clocks
could be empty. Dont return error in that case, because the probe of the
corresponding driver will not be called at all if this fails.
Better to continue to look for it and return 0.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/a9a9d853e0ac396cd9b3577cce26279a75765711.1693384296.git.michal.simek@amd.com
Add driver which implements GPIO-controlled clock. The GPIO is used
as a gate to enable/disable the clock. This matches linux clk-gpio.c
driver, however this does not implement the GPIO mux part, which in
U-Boot DM would be better fit in separate driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
To disabled a clock in clock tree initialization for a mux of STM32MP15,
the selected clock source index is set with the latest possible index for
the number of bit used. Today this valid configuration cause a error
in U-Boot messages, for example with CLK_ETH_DISABLED, when this clock
is not needed for the used ETH PHY without crystal:
no parents defined for clk id 123
This patch change the level of this message to avoid this trace for
valid clock tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Once all the other drivers got torn down in preparation for the OS
to start, tear down the clock controller last. The clock controller
must be torn down last as some of the clock which get turned off
might have still been needed during the teardown stage of the other
drivers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Signed-off-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Hai Pham <hai.pham.ud@renesas.com>
Add support to read RK3308 registers used to configure UART clocks, and
thus to get UART rate and baudrate. This fixes clock_get_rate returning
error on serial device probing. Moreover, there is no need anymore to
use 'clock-frequency' property for UART nodes in *-u-boot.dtsi files
for all cases where UART is not inited by U-Boot proper or by SPL o by
TPL code but by a preliminary external boot phase (for Rock PI S, UART
is inited by external TPL).
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
As per definitions of masks and shift offsets in cru_rk3308.h, values
read from registers must be first masked and then shifted. By the way,
this fix is binary invariant, because in all of fixed cases the shift
offset is zero.
Signed-off-by: Massimo Pegorer <massimo.pegorer+oss@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Pine64 Quartz64 boards DT reference SCLK_GMAC1_RGMII_SPEED in the
assigned-clocks property of the gmac1 node. This result in a ENOENT
error when driver core tries to set a parent for this clock.
The clock speed in rgmii/rmii mode is changed using clk_set_rate of the
tx_rx clock and not using clk_set_parent of the speed clock.
Add dummy support for SCLK_GMAC1_RGMII_SPEED and similar clocks to clk
driver to allow a driver for gmac node to probe.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The clock driver for RK3568 does not include support for UART clocks in
SPL. This result in the following message with high enough loglevel.
ns16550_serial serial@fe660000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
Fix this by including support for UART clocks in SPL.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The field for clk_cpll_div_25m_div in CRU_CLKSEL_CON81 is 6 bits wide,
not 5 bits wide as currently defined in CPLL_25M_DIV_MASK.
Fix this and the assert so that CPLL_25M can be assigned a 25 MHz rate.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix use of wrong clk selection for CLK_PWM1 on RK3568.
Fixes: 4a262feba3 ("rockchip: rk3568: add clock driver")
Signed-off-by: Damon Ding <damon.ding@rock-chips.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Handle USB480M clock ID in set_rate() and set_parent()
to allow the dt assigned-clocks and assigned-clock-parents
work on rk3328.dtsi
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Sean Anderson <seanga2@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Drop the PLL part in SYSCRG driver and separate to be a single
PLL driver of which the compatible is "starfive,jh7110-pll".
Signed-off-by: Xingyu Wu <xingyu.wu@starfivetech.com>
Signed-off-by: Hal Feng <hal.feng@starfivetech.com>
Reviewed-by: Torsten Duwe <duwe@suse.de>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Add gem_tsu and gem0_rx till gem3_rx to return proper register from
zynqmp_clk_get_register. Otherwise firmware won't be able to set clock
for these due to incorrect register address.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230720072859.3724-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
gem0_rx till gem3_rx and gem_tsu are missing from set rate function.
Add them, so that they can be set from pmu firmware via clock framework.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230719084912.30209-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Without CONFIG_CLK, the build fails with the following message:
LD u-boot
aarch64-none-linux-gnu-ld.bfd: drivers/firmware/scmi/scmi_agent-uclass.o: \
in function `scmi_bind_protocols':
.../drivers/firmware/scmi/scmi_agent-uclass.c:79: undefined reference to \
`_u_boot_list_2_driver_2_scmi_clock'
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
