T4240RDB supports booting from 2 nor banks(default and altbank). The
corresponding defconfig can only have one entry defined and therefore,
extend cs4340_get_fw_addr() function to overwrite firmware address which
will be later used in cortina firmware.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
T2080RDB supports booting from 2 nor banks(default and altbank). The
corresponding defconfig can only have one entry defined and therefore,
extend cs4340_get_fw_addr() function to overwrite firmware address which
will be later used in cortina firmware.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
LS2088A-RDB supports TFA boot source and has 2 nor banks(default and
altbank) and QSPI as boot source. The corresponding defconfig can only
have one entry defined and therefore, extend cs4340_get_fw_addr()
function to overwrite firmware address which will be later used in
cortina firmware.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Free dynamically allocated memory before every return statement
in calc_img_key_hash() and calc_esbchdr_esbc_hash() function.
Verified the secure boot changes using ls1046afrwy board.
Signed-off-by: Kshitiz Varshney <kshitiz.varshney@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Starting with board revision D, the MISCCSR CPLD register needs to be
configured to enable Power-on Reset for software reset commands.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART
Log as below: I would keep some debug info for now, and after we move
to be stable and production launch, we could drop that.
U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
Normal Boot
upower_init: soc_id=48
upower_init: version:11.11.6
upower_init: start uPower RAM service
user_upwr_rdy_callb: soc=b
user_upwr_rdy_callb: RAM version:12.6
Turn on switches ok
Turn on memories ok
Clear DDR retention ok
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F0 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
Poll for freq_chg_req on SIM register and change to F1 frequency.
Poll for freq_chg_req on SIM register and change to F2 frequency.
complete
De-Skew PLL is locked and ready
WDT: Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0
Load image from 0x3a800 by ROM_API
NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94
NOTICE: BL31: Built : 01:56:58, Jun 29 2021
NOTICE: upower_init: start uPower RAM service
NOTICE: user_upwr_rdy_callb: soc=b
NOTICE: user_upwr_rdy_callb: RAM version:12.6
U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800)
CPU: Freescale i.MX8ULP rev1.0 at 744 MHz
Reset cause: POR
Boot mode: Single boot
Model: FSL i.MX8ULP EVK
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 2
Loading Environment from MMC... ***
Warning - bad CRC, using default environment
In: serial@293a0000
Out: serial@293a0000
Err: serial@293a0000
Net:
Warning: ethernet@29950000 (eth0) using random MAC address -
96:35:88:62:e0:44
eth0: ethernet@29950000
Hit any key to stop autoboot: 0
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped support for networking and splash screen as these need
to be properly converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
It is a pain to have to specify the value 10 in each call. Add a new
dectoul() function and update the code to use it.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is a pain to have to specify the value 16 in each call. Add a new
hextoul() function and update the code to use it.
Add a proper comment to simple_strtoul() while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rename these options so that CONFIG_IS_ENABLED can be used with them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
It is quite confusing that CONFIG_SYS_I2C selects the legacy I2C and
CONFIG_DM_I2C selects the current I2C. The deadline to migrate I2C is less
than a year away.
Also we want to have a CONFIG_I2C for U-Boot proper just like we have
CONFIG_SPL_I2C for SPL, so we can simplify the Makefile rules.
Rename this symbol so it is clear it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
lx2160ardb Rev-C board has i2c node for thermal monitors
connected to different chip offset.
Add device tree fixup to use lx2160ardb dts and apply
thermal node fixups for lx2160ardb Rev-C board.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[sp:thernal->thermal]
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
[Squashed ls2088a patch to fix compilation]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Updates the board configuration to enable use of the PCA9547 I2C mux.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Refactors similar mux code from multiple NXP boards into a common location,
and allows it to be disabled in config.
New config: CONFIG_FSL_USE_PCA9547_MUX to enable PCA9547 mux functionality.
Signed-off-by: Stephen Carlson <stcarlso@linux.microsoft.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
As the logic here is only used when we have a USB host controller, test
on CONFIG_USB_HOST rather than CONFIG_USB in general. This lets us move
towards using CONFIG_USB only as a menu symbol to say that we have some
form of USB, and then USB_HOST or USB_GADGET depending on the role that
USB plays within the build.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. As this is also the last in family remove the related
support as well.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Angelo Durgehello <angelo.dureghello@timesys.com>
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Setup USB clock in board codes, and enable the DWC3 XHCI and
PHY drivers to make USB3.0 host port working on i.MX8MQ EVK.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
The default implementation of checkboard() calls the
nxp_board_rev_string() function
to retrieve a character representing the revision number of the board.
However, this
attempt to retrieve the revision number may fail in certain situations or be
otherwise undesirable.
There is already a configuration option to avoid retrieving the
revision number of
the board: CONFIG_NXP_BOARD_REVISION. In fact, if this option is enabled, the
nxp_board_rev_string() function's definition will be omitted entirely,
meaning that the previous implementation of checkboard() would result
in a linker error.
This changeset makes the default implementation of checkboard() respect the
CONFIG_NXP_BOARD_REVISION configuration option, only attempting to retrieve
the board revision number if that option is defined.
Signed-off-by: Cody Gray <cody@codygray.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_T4160 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8315 platform, remove that support as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the last
ARCH_MPC8568 platform, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline
and is also missing conversion to CONFIG_DM. Remove them. As this is
the only ARCH_T1023 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These boards have not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove them. As this is the only
ARCH_MPC8555 platform left, remove that support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_PCI by the deadline and is
also missing conversion to CONFIG_DM. Remove it. As this is the only
MPC8541 target left, remove that architecture support as well.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is the last of the mcf547x_8x family of boards,
remove that support as well.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These board has not been converted to CONFIG_DM_PCI by the deadline.
Remove them. As this is all of the CONFIG_M548x platforms as well,
remove that code.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
In some board cpld.h files the definition of the cpld_data struct
not-quite makes a typedef for cpld_data_t. This problem is caught with
gcc-11 as a multiple definition error. As there are no users of this
non-typedef, fix this by not declaring it one to begin with.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add Priyanka Jain as MAINTAINER for
T2080RDB_revD_defconfig,
T2080RDB_revD_NAND_defconfig,
T2080RDB_revD_SDCARD_defconfig and
T2080RDB_revD_SPIFLASH_defconfig
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Under DM, we rely on u-boot's device tree to provide the correct PHY
addresses. The board_fix_fdt callback is intended to be used for
device tree fixups before relocation. Unfortunately, this isn't an
option when booting from flash since the device tree isn't writable
before relocation.
This patch introduces the CONFIG_T2080RDB_REV_D option to signal that a
board revision D or up is the target. The config option is used to set
the correct Aquantia PHY address in the board's u-boot device tree.
Defconfig files with the option enable explicitly are added for
convenience.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The T2080RDB boards revisions D and up have updated 10G Aquantia PHYs
connected to MAC1 and MAC2. The second Aquantia PHY is located at a
different address on the MDIO bus compared to rev C (0x8 instead of 0x1).
Fix-up the Linux device tree to update the PHY address for the second
Aquantia PHY on boards revisions D and up. Also rename the PHY node to
reflect the changes.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Detect and print the board revision version based on the CPLD registers.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Both DM_ETH and DM_PCI are enabled for the T2080RDB board. Remove the
board_eth_init() callback and the non-DM_ETH code paths since they are not
needed anymore.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add check for return value of adjust_vdd()
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When using bootefi to boot a EFI binary, u-boot is supposed to
provide networking service for EFI application. Currently, 'pfe stop'
command is called from bootcmd before running bootefi. As a result
network stops working for EFI applications and console is flooded with
"Rx pkt not on expected port" messages.
Implement board_quiesce_devices() for ls1012a boards and call
pfe_command_stop() from it instead of calling 'pfe stop' from
*_bootcmd and bootcmd.
Tested-by: Anji Jagarlmudi <anji.jagarlmudi@nxp.com>
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
[Fixed checkpatch space error]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
These specific configs are missing a number of migrations. In addition,
they are blocking completion of the now-expired DM_MMC migration as it
requires enabling BLK.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Current setup instructions for i.MX8QM MEK board include somewhat
conflicting instructions, so here's an attempt to fix it.
After trying both sets of firmwares, I can conclude that both of
them fail to work:
- no boot at all with imx-sc-firmware-0.7 / firmware-imx-7.6
- partial success with imx-sc-firmware-1.1 / firmware-imx-8.0:
U-Boot 2021.04-rc3-00135-ge0669a43c8 (Mar 08 2021 - 16:49:08 +0200)
CPU: NXP i.MX8QM RevB A53 at 1200 MHz
Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
mu_hal_receivemsg timeout
Build: SCFW 65afe5f6, SECO-FW 65afe5f6, ATF a-20190
mu_hal_receivemsg timeout
sc_misc_get_boot_dev: res:16
Boot: SD0
DRAM: mu_hal_sendmsg timeout
sc_rm_is_memreg_owned: mr:0 res:21
...
Signed-off-by: Priit Laes <priit.laes@paf.com>
Disable the FMan mEMAC 5 and 6 nodes from the fdt since they are not
available under the supported RCW. Also disable the associated
"fsl,dpa-ethernet" nodes that reference them.
This is a simplified version of the fdt_fixup_fman_ethernet call for
use under DM_ETH.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
It is not recommended to use CONFIG_xxx defines for things which are not
Kconfig options. Rename this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it. It is also the only ARCH_T2081 board so remove that support
as well.
Cc: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Cc: Ruchika Gupta <ruchika.gupta@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Cc: Ye Li <ye.li@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board has not been converted to CONFIG_DM_MMC by the deadline.
Remove it.
Cc: Eddy Petrișor <eddy.petrisor@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board relies on using CONFIG_LIBATA but does not enable CONFIG_AHCI. The
deadline for this conversion was the v2019.07 release. The use of CONFIG_AHCI
requires CONFIG_DM. The deadline for this conversion was v2020.01. Remove
this board.
Signed-off-by: Tom Rini <trini@konsulko.com>
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
While initializing dram in spl_dram_init(), mdelay() is called that in
order calls get_ticks() that verifies if timer exists, if doesn't, it
throws a panic(), but since preloader_console_init() has still not been
called those panic()s will fail. This doesn't help debugging, so let's
setup console before calling spl_dram_init() by moving it after
spl_dram_init().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Both i.MX8MQ B1 and B2 should use default LPDDR4 script, while B0
has another dedicated script.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Users reported LPDDR4 MR12 value is set to 0 during PHY training,
not the value from FSP timing structure, which cause compliance test failed.
The root cause is the CATrainOpt[0] is set to 1 in 2D FSP timing
but not set in 1D. According to PHY training application node,
to enable the feature both 1D and 2D need set this field to 1,
otherwise the training result will be incorrect.
The PHY training doc also recommends to set CATrainOpt[0] to 0 to use
MR12 value from message block (FSP structure). So update the LPDDR4
scripts of all mscale to clear CATrainOpt[0].
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add dedicated defconfigs for iMX8MN low drive mode which set the VDD_SOC
and VDD_DRAM to 0.8v, DDR at 1600MTS (800Mhz clock) and GPU at 200Mhz.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add support for iMX8MN LPDDR4 EVK board which uses 2GB LPDDR4 and
PCA9450B PMIC.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Currently PCA9450 might have address 0x25 or 0x35, so let user
choose the address.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
On i.MX8MN, we can only support DLL-ON mode only, so update the timing
to support 2400mts & 1066mts setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
There is a frequency/timing limitation for SOC and ARM, if SOC is OD
voltage/OD freq, then ARM can't run at ND voltage/1.2Ghz, it may have
timing risk from SOC to ARM.
Current VDD_SOC is set to 0.95v OD voltage in SPL, and kernel will
increase bus clocks to OD frequency before it increases ARM voltage.
So to conform to the limitation, we'd better increases VDD_ARM to OD
voltage in SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
VDD SOC normal run changed to 0.85V
LPDDR4 freq0 change from 4000MTS to 2400MTS
Signed-off-by: haidong.zheng <haidong.zheng@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Use more safer refresh time value for 6GB LPDDR4 on this EVK board.
Update the parameters for every frequency point.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
After switching to new LPDDR4 firmware 202006 version, have to
update the LPDDR4 timing accordingly from RPA tool.
Signed-off-by: Ye Li <ye.li@nxp.com>
Tested-by: Sherry Sun <sherry.sun@nxp.com>
Tested-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add inline ECC support for lpddr4 on imx8mp-evk. And add a config which
can enable/disable inline ECC feature for lpddr4 on imx8mp-evk board.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The User Guide contains handy things like block diagrams and DIP switch
settings and it's even available on the public web. Add a link to it in
the README.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
board/emulation is the place for other QEMU targets like x86, arm,
riscv. Let's move the qemu-ppce500 board codes there.
List me as a co-maintainer for this board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This function is not called anywhere. Only fsl_ddr_sdram_size() is
necessary [1] for QEMU. Drop it.
[1] arch/powerpc/cpu/mpc85xx/cpu.c::dram_init()
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now that we have switched to CONFIG_OF_CONTROL, and we can use the
env variable 'fdtcontroladdr' directly instead of creating one that
is duplicated.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
