Commit graph

350 commits

Author SHA1 Message Date
Wu, Josh
2ab4c74604 at91: 9x5: change SMC config timing that both works for PMECC & non-PMECC.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: voice.shen@atmel.com
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 17:06:14 +02:00
Andreas Bießmann
bfc325ed38 arm:at91-boards: remove console_init_f where unnecessary
A lot of at91 boards have the console_init_f in board_init. This is useless
cause it was called before by generic code in lib/board.c.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Jens Scharsig <esw@bus-elektronik.de>
cc: Stelian Pop <stelian@popies.net>
cc: Sedji Gaouaou<sedji.gaouaou@atmel.com>
cc: Albin Tonnerre <albin.tonnerre@free-electrons.com>
cc: Eric Benard <eric@eukrea.com>
Tested-by: voice.shen@atmel.com
Tested-by: voice.shen@atmel.com
Acked-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Tested-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
2012-09-01 17:06:14 +02:00
Andreas Bießmann
82c4c64526 at91sam9263ek: remove unnecessary console_init_f
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
cc: Stelian Pop <stelian@popies.net>
2012-09-01 17:06:14 +02:00
Bo Shen
4ed9c88603 arm : at91sam9x5 : fix a small bug for NAND
fix a bug:
  when not boot from NAND, the NAND flash can not be detected.
  Using this to fix it

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 17:06:13 +02:00
Bo Shen
f7fa2f3740 arm : Atmel : add at91sam9x5ek board support
Add at91sam9x5ek board support, this board support the following SoCs
  AT91SAM9G15, AT91SAM9G25, AT91SAM9G35, AT91SAM9X25, AT91SAM9X35

Using at91sam9x5ek_nandflash to configure for the board
Now only supports NAND with software ECC boot up

Signed-off-by: Bo Shen <voice.shen@atmel.com>
[move MAINTAINERS entry to right place]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-09-01 14:58:14 +02:00
Alexandre Belloni
e139cb31d3 AT91SAM9*: Change kernel address in dataflash to match u-boot's size
On at91sam platforms, u-boot grew larger than the allocated size in
dataflash, the layout was:
bootstrap  0x00000000
ubootenv   0x00004200
uboot      0x00008400
kernel     0x00042000
fs         0x00252000

u-boot with the defconfig doesn't seem to fit in 0x42000 - 0x8400 =
0x39C00 bytes anymore.

Now, the layout is:
bootstrap  0x00000000
ubootenv   0x00004200
uboot      0x00008400
kernel     0x00084000
fs         0x00294000

Signed-off-by: Alexandre Belloni <alexandre.belloni@piout.net>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:30 +02:00
esw@bus-elektronik.de
2feb736661 Fix: broken boot message at serial line on AT91SAM9263-EK board
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2012-07-07 14:07:29 +02:00
Stelian Pop
c9e798d35a Fix Stelian's email address
Change my old email address which is no longer valid.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2011-11-29 15:43:38 +01:00
Mike Frysinger
464c79207c punt unused clean/distclean targets
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used.  Punt them all.

MAKEALL didn't report any errors related to this that I could see.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2011-10-15 22:20:36 +02:00
Jason Kridner
2d3be7c456 led: remove camel casing of led identifiers globally
Result of running the following command to address Wolfgang's
comment about camel case:

for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done

Discussion:
http://patchwork.ozlabs.org/patch/84988/

Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
2011-09-13 08:30:52 +02:00
Wolfgang Denk
1c85752258 ARM: remove broken "at91rm9200dk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
2011-09-04 11:36:15 +02:00
Wolfgang Denk
b550834458 ARM: remove broken "at91cap9adk" board
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stelian Pop <stelian.pop@leadtechdesign.com>
2011-09-04 11:36:14 +02:00
Thomas Petazzoni
5cfeec5125 atmel: Update support of board AT91SAM9M10G45-EK to new style
Based on earlier work by Alex Waterman <awaterman@dawning.com>.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
2011-09-03 22:40:45 +02:00
Xu, Hong
cd46b0f2b9 AT91: Makes AT91SAM9263-EK build correctly against u-boot-atmel/master
Rework for AT91SAM9263-EK, makes it build again.
Based on the work for AT91SAM9260-EK.

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <uboot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Xu, Hong
f7aea46d6a AT91: Board fix for AT91SAM9261-EK
Fix board part of AT91SAM9261-EK according to the new scheme

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Xu, Hong
21d671d0c4 AT91: Makes AT91SAM9RL-EK build correctly against u-boot-atmel/master
Rework for AT91SAM9RL-EK, makes it build again.
Based on the work for AT91SAM9260-EK.
V4: added changes to MAKEALL

Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-08-03 13:00:56 +02:00
Albert ARIBAUD
a55d23ccf6 Remove volatile qualifier in get_ram_size() calls
Checkpatch.pl complains about the volatile qualifier in calls to
get_ram_size(). Remove this qualifier in the prototype and in the
calls where it is useless, and leave it only in the function body
where it is needed.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2011-07-17 17:11:53 +02:00
Graeme Russ
a60d1e5b8e Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-07-16 11:55:00 +02:00
Andreas Bießmann
221786525f atstk100x: switch to common cfi driver
This patch removes the board implemenatation for flash driver which can now
safely switched to the common cfi driver.

Compile tested for all atstk100x boards, runtime tested on atstk1002.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-07-04 10:55:27 +02:00
Andreas Bießmann
3432a93bcd at91rm9200ek: use atmel_usart
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2011-07-04 10:55:27 +02:00
Reinhard Meyer
8c6407fce3 AT91 rework: fix at91sam(9260/9g20/9xe)ek board port to build again:
Make ATMEL's at91sam9260/9g20/9xe-ek boards build again

Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2011-06-21 22:26:22 +02:00
Jens Scharsig
8073399444 update arm/at91rm9200 work with rework rework110202
* convert at91rm9200ek and eb_cpux9k2 board to ATMEL_xxx name scheme
 * Fix: timer.c compile error io.h not found with arm/at91rm9200
 * update arm920t/at91 to ATMEL_xxx name scheme
 * update arm920t/at91 soc lib
 * update at91_emac driver

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Tested-by: Andreas Bießmann <andreas.devel@gmail.com>
2011-06-21 22:26:21 +02:00
Andreas Bießmann
47293c18ba atstk100x: move CONFIG_SYS_TEXT_BASE to header
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:54 +02:00
Andreas Bießmann
da48437230 atngw100: move CONFIG_SYS_TEXT_BASE to header
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:54 +02:00
Andreas Bießmann
bb7dc6af20 avr32: use single linker script
This patch move the atstk100x linker script to $(CPUDIR) and delete other
pure copies of this file in each board directory.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:53 +02:00
Andreas Bießmann
758472cc7b avr32/config.mk: simplify PLATFORM_RELFLAGS
This patch removes PLATFORM_RELFLAGS from board specific config.mk files and
define them in arch specific config.mk file.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:53 +02:00
Andreas Bießmann
c8e7ddd4c6 avr32: fix linking
This patch fixes following error:

---8<---
avr32-linux-ld: --gc-sections and -r may not be used together
--->8---

Since 8aba9dceeb all avr32 boards are broken due
to linking error as seen above.

Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:52 +02:00
Andreas Bießmann
f4278b716c avr32: fixup definitions to ATMEL_BASE_xxx
Signed-off-by: Andreas Bießmann <biessmann@corscience.de>
2011-05-18 07:56:50 +02:00
Scott Wood
83b7e2a7f2 Handle most LDSCRIPT setting centrally
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk.  Some
are found using an arch-specific rule for looking in CPUDIR, etc.

Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.

Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.

If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.

If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:

$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds

Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules.  These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
2011-04-30 00:59:47 +02:00
Po-Yu Chuang
44c6e6591c rename _end to __bss_end__
Currently, _end is used for end of BSS section.  We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.

Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
2011-03-27 19:18:37 +02:00
Andreas Bießmann
3a4ff8b3cd at91rm9200ek: add configure target for RAM boot
This patch also removes now unnecessary config.mk in board directory and
make usage of new features in boards.cfg.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2010-12-07 22:08:06 +01:00
Sebastien Carlier
6d8962e814 Switch from archive libraries to partial linking
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils.  As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".

This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.

The name of each former library archive is preserved except for
extensions which change from ".a" to ".o".  This commit updates
references accordingly where needed, in particular in some linker
scripts.

This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols.  Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.

Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
2010-11-17 21:02:18 +01:00
Andreas Bießmann
99fa97e955 at91rm9200ek: convert to at91
This patch removes some functionality from at91rm9200ek board but the
remaining functionality does now work with newer at91 code and
arm-relocation.

Currently missing features are:
 - dataflash booting (due to missing HW for testing)
 - MMC/SD-Card
 - first stage bootloader support is completely removed (not needed for
   NOR)

Cause this board was (some days ago) reference for all at91rm9200 based
boards this should be a good starting point to convert all remaining
at91rm9200 borads to at91 code. Aside from that this is a good base to
get some drivers between at91sam/at91rm/avr32 merged.

Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Reinhard Meyer <u-boot@emk-elektronik.de>
2010-10-19 15:11:46 +02:00
Wolfgang Denk
14d0a02a16 Rename TEXT_BASE into CONFIG_SYS_TEXT_BASE
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.

Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2010-10-18 22:07:10 +02:00
Haavard Skinnemoen
1f36f73fe7 avr32: Add simple paging support
Use the MMU hardware to set up 1:1 mappings between physical and virtual
addresses. This allows us to bypass the cache when accessing the flash
without having to do any physical-to-virtual address mapping in the CFI
driver.

The virtual memory mappings are defined at compile time through a sorted
array of virtual memory range objects. When a TLB miss exception
happens, the exception handler does a binary search through the array
until it finds a matching entry and loads it into the TLB. The u-boot
image itself is covered by a fixed TLB entry which is never replaced.

This makes the 'saveenv' command work again on ATNGW100 and other boards
using the CFI driver, hopefully without breaking any rules.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2010-09-03 15:13:02 +02:00
Haavard Skinnemoen
9cec2fc209 avr32: Use uncached() macro to get an address for SDRAM init
The paging system which is required to set up caching properties has not
yet been initialized when the SDRAM is initialized. So when the
map_physmem() function is converted to return the physical address
unchanged, the SDRAM initialization will break on some boards.

The avr32-specific uncached() macro will return an address which will
always cause uncached accessed to be made. Since this happens in the
board code, using avr32-specific features should be ok, and will allow
the SDRAM initialization to keep working.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2010-09-03 15:12:52 +02:00
Ben Warren
6bb4679017 Write MAC address automatically on MACB-based boards
Also, remove all calls to eth_init() in boards that use MACB

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-07-12 00:14:29 -07:00
Sergey Matyukevich
64203c7b0f USB OHCI support for at91sam9g45 SoC
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.

Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.

Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
2010-06-30 21:37:36 +02:00
Andreas Bießmann
418cbb0abc avr32: fix linking of atstk100x and favr32 boards
When building some avr32 boards out of tree (e.g. O=..) the linker script could
not be found. This patch references the linker script in source tree.

Signed-off-by: Andreas Biemann <biessmann@corscience.de>
2010-06-29 22:37:11 +02:00
Achim Ehrlich
7c966a8bdf ARM change name of defines for AT91 arm926ejs
Configuration defines should be preceeded with CONFIG_SYS_. Renamed
some at91 specific defines to conform to this naming convention:

AT91_CPU_NAME to CONFIG_SYS_AT91_CPU_NAME
AT91_MAIN_CLOCK to CONFIG_SYS_AT91_MAIN_CLOCK

Signed-off-by: Achim Ehrlich <aehrlich@taskit.de>
2010-03-07 12:36:35 -06:00
Jens Scharsig
1b34f00c28 update at91sam9263ek board to new SoC access
* convert at91sam9263ek board to use c stucture SoC access
 * change gpio access to at91_gpio syntax

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
2010-02-12 12:31:55 -06:00
Jens Scharsig
c041e9d212 new at91_emac network driver (NET_MULTI api)
* add's at91_emac (AT91RM9200) network driver (NET_MULTI api)
* enable driver with CONFIG_DRIVER_AT91EMAC
* generic PHY initialization
* modify AT91RM9200 boards to use NET_MULTI driver
* the drivers has been tested with LXT971 Phy and DM9161 Phy at
  MII and RMII interface

Signed-off-by: Jens Scharsig <js_at_ng@scharsoft.de>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2010-01-31 22:37:12 -08:00
Wolfgang Denk
e8fac25e83 at91sam9261ek.c: fix minor coding style issue.
Signed-off-by: Wolfgang Denk <wd@denx.de>
2009-12-07 21:50:19 +01:00
Albin Tonnerre
50b5fff558 at91sam9260/afeb9260: Fix SPI initialization
Commit 7ebafb7ec1 introduced a mistake in the spi
init function call for those boards. This patch fixes this.

Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
2009-09-01 22:10:10 +02:00
Sedji Gaouaou
5ccc2d99d6 at91: Introduction of at91sam9g10 SOC.
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:56:11 +02:00
Sedji Gaouaou
22ee647380 at91: Introduction of at91sam9g45 SOC.
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.

The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
2009-07-12 17:43:34 +02:00
Sedji Gaouaou
0aafde1dc7 at91sam9260/9263: add back up for the rst(reset controller).
On the boards at91sam9260ek, at91sam9263ek and afed9260, the rstc register was
set to 0 after being set to 500 ms for the PHY reset.
Do backup the old reset length and restore it after the MACB initialisation.

Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Stelian Pop <stelian@popies.net>
2009-07-06 21:50:09 +02:00
Jean-Christophe PLAGNIOL-VILLARD
8096c51fd4 at91: unify nor boot support
the lowlevel init sequence is the same so unify it

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:12 +02:00
Jean-Christophe PLAGNIOL-VILLARD
1b3b7c640d at91sam9263ek: add nor flash support
this will allow you to store use it for the env and to boot directly U-Boot from

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-21 16:18:11 +02:00
Remy Bohmer
60f61e6d76 Convert DM9000 driver for CONFIG_NET_MULTI
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.

Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2009-06-15 00:13:55 -07:00
Jean-Christophe PLAGNIOL-VILLARD
10a451cd57 arm: unify linker script
all arm boards except a few use the same cpu linker script
so move it to cpu/$(CPU)

that could be overwrite in following order
SOC
BOARD
via the corresponding config.mk

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:39:52 +02:00
Jean-Christophe PLAGNIOL-VILLARD
b54384e3ba arm: timer and interrupt init rework
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow

so now rename it as int timer_init(void) and use interrupt_init for interrupt

btw also remane the corresponding file to the functionnality implemented

as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-06-12 20:39:48 +02:00
Detlev Zundel
792a09eb9d Fix e-mail address of Gary Jennejohn.
Signed-off-by: Detlev Zundel <dzu@denx.de>
2009-05-15 22:11:59 +02:00
Jean-Christophe PLAGNIOL-VILLARD
dc39ae9513 at91sam9/at91cap: improve clock framework
calculate dynamically the clock rate and pllb setting for usb

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-16 21:30:44 +02:00
Wolfgang Denk
c0a14aedc3 Update CHANGELOG, coding style cleanup. 2009-04-05 00:27:57 +02:00
Jean-Christophe PLAGNIOL-VILLARD
f82518d7f4 at91rm9200: Reset update
Update the rm9200 reset sequence to try executing a board-specific reset
function and move specific board reset to board.

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:21 +02:00
Ulf Samuelsson
cb82a53266 Add support for the AT91RM9200EK Board.
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507

with
	- NOR (cfi driver)
	- DataFlash
	- USB OHCI
	- Net
	- I2C (hard)

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:20 +02:00
Jean-Christophe PLAGNIOL-VILLARD
2a325ce3c7 at91rm9200dk: Move conditional compilation to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:19 +02:00
Jean-Christophe PLAGNIOL-VILLARD
90a92a708d at91: rename DATAFLASH_MMC_SELECT to CONFIG_DATAFLASH_MMC_SELECT
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-04-04 20:42:19 +02:00
Wolfgang Denk
aaa0e0812f Merge branch 'master' of git://git.denx.de/u-boot-at91 2009-03-26 22:27:45 +01:00
Haavard Skinnemoen
8206bfae3a Merge branch 'mimc200' 2009-03-23 10:22:41 +01:00
Nicolas Ferre
df486b1fa3 at91: Support for the at91sam9g20 : Atmel 400Mhz ARM 926ej-s SOC.
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.

The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.

Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337

Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 14:48:16 +01:00
Jean-Christophe PLAGNIOL-VILLARD
74c076d6c3 at91sam9/at91cap: move nand drivers to drivers/mtd/nand
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:24 +01:00
Jean-Christophe PLAGNIOL-VILLARD
163966087d atmel/at91/boards: compile dataflash partition only when dataflash is
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:19 +01:00
Jean-Christophe PLAGNIOL-VILLARD
e2c0476f95 at91sam9/at91cap: move common macb initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:14 +01:00
Jean-Christophe PLAGNIOL-VILLARD
f3f91f886b at91sam9/at91cap: move common usb host initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:11 +01:00
Jean-Christophe PLAGNIOL-VILLARD
a484b00b86 at91sam9/at91cap: move common led management to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:08 +01:00
Jean-Christophe PLAGNIOL-VILLARD
7ebafb7ec1 at91sam9/at91cap: move common spi initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:06 +01:00
Jean-Christophe PLAGNIOL-VILLARD
1332a2a069 at91sam9/at91cap: move common serial initialisation to cpu
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2009-03-22 13:22:03 +01:00
Trent Piepho
f62fb99941 Fix all linker script to handle all rodata sections
A recent gcc added a new unaligned rodata section called '.rodata.str1.1',
which needs to be added the the linker script.  Instead of just adding this
one section, we use a wildcard ".rodata*" to get all rodata linker section
gcc has now and might add in the future.

However, '*(.rodata*)' by itself will result in sub-optimal section
ordering.  The sections will be sorted by object file, which causes extra
padding between the unaligned rodata.str.1.1 of one object file and the
aligned rodata of the next object file.  This is easy to fix by using the
SORT_BY_ALIGNMENT command.

This patch has not be tested one most of the boards modified.  Some boards
have a linker script that looks something like this:

*(.text)
. = ALIGN(16);
*(.rodata)
*(.rodata.str1.4)
*(.eh_frame)

I change this to:

*(.text)
. = ALIGN(16);
*(.eh_frame)
*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))

This means the start of rodata will no longer be 16 bytes aligned.
However, the boundary between text and rodata/eh_frame is still aligned to
16 bytes, which is what I think the real purpose of the ALIGN call is.

Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
2009-03-20 22:39:12 +01:00
Olav Morken
d8f2aa3298 AVR32: Make cacheflush cpu-dependent
The AT32UC3A series of processors doesn't contain any cache, and issuing
cache control instructions on those will cause an exception. This commit
makes cacheflush.h arch-dependent in preparation for the AT32UC3A-support.

Signed-off-by: Gunnar Rangoy <gunnar@rangoy.com>
Signed-off-by: Paul Driveklepp <pauldriveklepp@gmail.com>
Signed-off-by: Olav Morken <olavmrk@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2009-02-23 10:34:23 +01:00
Haavard Skinnemoen
cb54732052 Merge branch 'fixes' into cleanups
Conflicts:

	board/atmel/atngw100/atngw100.c
	board/atmel/atstk1000/atstk1000.c
	cpu/at32ap/at32ap700x/gpio.c
	include/asm-avr32/arch-at32ap700x/clk.h
	include/configs/atngw100.h
	include/configs/atstk1002.h
	include/configs/atstk1003.h
	include/configs/atstk1004.h
	include/configs/atstk1006.h
	include/configs/favr-32-ezkit.h
	include/configs/hammerhead.h
	include/configs/mimc200.h
2008-12-17 16:53:07 +01:00
Stelian Pop
ad229a44e1 AT91: Use AT91_CPU_CLOCK in displays
Introduce AT91_CPU_CLOCK and use it for displaying the CPU
speed in the LCD driver.

Also make AT91_MAIN_CLOCK and AT91_MASTER_CLOCK reflect the
corresponding board clocks.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-11-21 01:41:14 +01:00
Selvamuthukumar
9b827cf172 Align end of bss by 4 bytes
Most of the bss initialization loop increments 4 bytes
at a time. And the loop end is checked for an 'equal'
condition. Make the bss end address aligned by 4, so
that the loop will end as expected.

Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-11-18 23:13:16 +01:00
Stelian Pop
d8003fa037 AT91: Replace AT91_BASE_EMAC by the board specific values.
AT91_BASE_EMAC is never used outside the board specific files,
so replace its usage by the board specific AT91xxx_BASE_EMAC.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-11-07 13:54:31 +01:00
Stelian Pop
c91e17affa AT91: Replace (undefined) AT91_ID_US* by the board specific values.
AT91_ID_US0 / AT91_ID_US1 / AT91_ID_US2 were used but never defined.
Since they are never used outside the board specific files, they can
be replaced by the board specific AT91xxx_ID_US0 / AT91xxx_ID_US1 /
AT91xxx_ID_US2.

Bug spotted by Jesus Alvarez <jalvarez@micromint.com>.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-11-07 12:09:21 +01:00
Haavard Skinnemoen
6b59e03e02 lcd: Let the board code show board-specific info
The information displayed when CONFIG_LCD_INFO is set is inherently
board-specific, so it should be done by the board code. The current code
dealing with this only handles two cases, and is already a horrible mess
of #ifdeffery.

Yes, this duplicates some code, but it also allows boards to print more
board-specific information; this used to be very difficult.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
2008-10-27 09:53:58 +01:00
Jean-Christophe PLAGNIOL-VILLARD
6d0f6bcf33 rename CFG_ macros to CONFIG_SYS
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-10-18 21:54:03 +02:00
Wolfgang Denk
afbc526336 Merge branch 'Makefile-next' of git://git.denx.de/u-boot-arm 2008-09-12 16:13:12 +02:00
Claudio Scordino
8cc62a7d9c Fix MACH_TYPE for the AT91RM9200DK board.
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
2008-09-12 02:20:46 +02:00
Jean-Christophe PLAGNIOL-VILLARD
0e8d158664 rename CFG_ENV macros to CONFIG_ENV
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-09-10 22:48:06 +02:00
Ben Warren
3ae071e442 Moved initialization of Ethernet controllers on Atmel AT91 to board_eth_init()
Removed at91sam9_eth_initialize() from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02 21:18:16 -07:00
Ben Warren
89973f8a82 Introduce netdev.h header file and remove externs
This addresses all drivers whose initializers have already
been moved to board_eth_init()/cpu_eth_init().

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
2008-09-02 21:18:16 -07:00
Haavard Skinnemoen
d928525795 atstk1000: Convert to new-style makefile
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-01 14:35:12 +02:00
Haavard Skinnemoen
25e6854d42 avr32: use board_early_init_r instead of board_init_info
Replace the avr32-specific board_init_info hook by the standard
board_early_init_r hook and make it optional.

board_early_init_r() runs somewhat earlier than board_init_info used to
do, but this isn't a problem for any of the in-tree boards.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-09-01 14:21:35 +02:00
Haavard Skinnemoen
ab0df36fc7 avr32: refactor the portmux/gpio code
- Separate the portmux configuration functionality from the GPIO pin
    control API.
  - Separate the controller-specific code from the chip-specific code.
  - Allow "ganged" port configuration (multiple pins at once).
  - Add more flexibility to the "canned" peripheral select functions:
      - Allow using more than 23 address bits, more chip selects, as
	well as NAND- and CF-specific pins.
      - Make the MACB SPEED pin optional, and choose between MII/RMII
	using a parameter instead of an #ifdef.
      - Make it possible to use other MMC slots than slot 0, and support
	different MMC/SDCard data bus widths.
  - Use more reasonable pull-up defaults; floating pins may consume a
    lot of power.
  - Get rid of some custom portmux code from the mimc200 board code. The
    old gpio/portmux API couldn't really handle its requirements, but
    the new one can.
  - Add documentation.

The end result is slightly smaller code for all boards. Which isn't
really the point, but at least it isn't any larger.

This has been verified on ATSTK1002 and ATNGW100. I'd appreciate if
the board maintainers could help me test this on their boards. In
particular, the mimc200 port has lost a lot of code, so I'm hoping Mark
can help me out.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Hans-Christian Egtvedt <hans-christian.egtvedt@atmel.com>
Cc: Mark Jackson <mpfj@mimc.co.uk>
Cc: Alex Raimondi <alex.raimondi@miromico.ch>
Cc: Julien May <julien.may@miromico.ch>

Changes since v1:
  * Enable pullup on NWAIT
  * Add missing include to portmux-pio.h
  * Rename CONFIG_PIO2 -> CONFIG_PORTMUX_PIO to match docs
2008-09-01 14:20:41 +02:00
Haavard Skinnemoen
d3c23a790f Merge branch 'next' of git://git.denx.de/u-boot-avr32
Conflicts:

	MAINTAINERS
2008-08-20 09:37:09 +02:00
Scott Wood
aa5f75f20d at91: Update board NAND drivers to current API.
Signed-off-by: Scott Wood <scottwood@freescale.com>
2008-08-13 15:56:00 -05:00
Haavard Skinnemoen
b8ec9fb736 Merge branch 'eth-cleanup' of git://git.denx.de/u-boot-avr32 2008-07-30 10:07:02 +02:00
Ben Warren
c8c845cfdc Moved initialization of AVR32 Ethernet controllers to board_eth_init()
Renamed initialization functions for atngw100 and atstk1000.
Removed initializations for these boards from net/eth.c

Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-24 12:37:26 +02:00
Haavard Skinnemoen
7f4b009f42 avr32: Fix printf() format warnings
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-07-23 16:15:01 +02:00
Anatolij Gustschin
17bd170714 at91: Fix to enable using Teridian MII phy (78Q21x3) with at91sam9260
On the at91sam9260ep development board there is an EEPROM
connected to the TWI interface (PA23, PA24 Peripheral A
multiplexing), so we cannot use these pins as ETX2, ETX3.
This patch configures PA10, PA11 pins for ETX2, ETX3
instead of PA23, PA24 pins.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Manuel Sahm <Manuel.Sahm@feig.de>
2008-07-13 14:41:45 +02:00
Wolfgang Denk
4e0018f1cf Merge branch 'master' of git://www.denx.de/git/u-boot-at91 2008-07-07 00:47:58 +02:00
Wolfgang Denk
b223017f08 Merge branch 'master' of git://www.denx.de/git/u-boot-avr32 2008-07-07 00:39:43 +02:00
Patrice Vilchez
d3bcdf838e [AT91SAM9] Fix NAND FLASH timings
Fix NAND FLASH timings for at91sam9x evaluation kits.

New timings are based on application note
"NAND Flash Support on AT91SAM9 Microcontrollers" available at
http://atmel.com/dyn/resources/prod_documents/doc6255.pdf

Signed-off-by: Patrice Vilchez <patice.vilchez@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Stelian Pop <stelian@popies.net>
2008-07-05 17:32:22 +02:00
Stelian Pop
19bd688484 Fix boot from NOR due to incorrect reset delay.
AT91 RSTC registers are battery-backuped, so their values
are not reset across power cycles. One of those registers,
the AT91_RSTC_MR register, is being modified by U-Boot, in
the ethernet initialisation routine, to generate a 500ms
user reset.

Unfortunately, this value is not being restored afterwards,
causing subsequent resets to also last for 500ms.

This long reset sequence causes problems (at least) in the
boot sequence from NOR: by the time the CPU tries to load
a program from the NOR flash, the latter is still in reset
and not yet available.

Additionaly, this patch fixes a bug in the original code which
caused the reset delay to last for 2s instead of 500ms.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-07-05 17:32:22 +02:00
Wolfgang Denk
c8a3b109f0 Cleanup out-or-tree building for some boards (.depend)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:49:18 +02:00
Haavard Skinnemoen
5f723a3b98 avr32: Enable SPI flash support on ATNGW100
The ATNGW100 has 8MB DataFlash on board. Give users access to it through
the new SPI flash framework.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-20 12:46:48 +02:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Wolfgang Denk
912810eeca Merge remote branch 'u-boot-at91/for-1.3.4' 2008-06-03 00:24:36 +02:00
Haavard Skinnemoen
a23e277c4a avr32: Rework SDRAM initialization code
This cleans up the SDRAM initialization and related code a bit, and
allows faster booting.

  * Add definitions for EBI and internal SRAM to asm/arch/memory-map.h
  * Remove memory test from sdram_init() and make caller responsible
    for verifying the SDRAM and determining its size.
  * Remove base_address member from struct sdram_config (was sdram_info)
  * Add data_bits member to struct sdram_config and kill CFG_SDRAM_16BIT
  * Add support for a common STK1000 hack: 16MB SDRAM instead of 8.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:31 +02:00
Haavard Skinnemoen
caf83ea888 avr32: Use the same entry point for reset and exception handling
Since the reset vector is always aligned to a very large boundary, we
can save a couple of KB worth of alignment padding by placing the
exception vectors at the same address.

Deciding which one it is is easy: If we're handling an exception, the
CPU is in Exception mode. If we're starting up after reset, the CPU is
in Supervisor mode. So this adds a very minimal overhead to the reset
path (only executed once) and the exception handling path (normally
never executed at all.)

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:30 +02:00
Haavard Skinnemoen
44453b25b0 avr32: Clean up the HMATRIX code
Rework the HMATRIX configuration interface so that it becomes easier
to configure the HMATRIX for boards with special needs, and add new
parts.

The HMATRIX header file has been split into a general,
chip-independent part with register definitions, etc. and a
chip-specific part with SFR bitfield definitions and master/slave
identifiers.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:29 +02:00
Haavard Skinnemoen
0a2e48792d avr32: Add support for the ATSTK1006 board
This is a replacement for ATSTK1002 with 64MB SDRAM and NAND flash on
board. It's currently in production and will be available soon.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:29 +02:00
Haavard Skinnemoen
781eb9a1e4 avr32: Get rid of the .flashprog section
The .flashprog section was only needed back when we were running
directly from flash, and it's even more useless on NGW100 since it
uses the CFI flash driver which never used this workaround in the
first place.

Remove it on STK1000 as well, and get rid of all the associated code and
annotations.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:29 +02:00
Jean-Christophe PLAGNIOL-VILLARD
42fd5f87b1 Merging Stelian Pop AT91 patches
Merge branch 'testing-V2'

Conflicts:

	board/atmel/at91cap9adk/Makefile
                Fixing copyright
	board/atmel/at91sam9260ek/Makefile
                Fixing copyright
	board/atmel/at91sam9260ek/u-boot.lds
                Delete no more needed ld script

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-24 12:56:53 +02:00
Wolfgang Denk
53677ef18e Big white-space cleanup.
This commit gets rid of a huge amount of silly white-space issues.
Especially, all sequences of SPACEs followed by TAB characters get
removed (unless they appear in print statements).

Also remove all embedded "vim:" and "vi:" statements which hide
indentation problems.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-05-21 00:14:08 +02:00
Stelian Pop
19883aede2 Support AT91CAP9 revC CPUs
The AT91CAP9 revC CPU has a few differences over the previous,
revB CPU which was distributed in small quantities only (revA was
an internal Atmel product only).

The revC silicon needs a special initialisation sequence to
switch from the internal (imprecise) RC oscillator to the
external 32k clock.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:45:03 +02:00
Stelian Pop
761c70b80c AT91SAM9RLEK: hook up the ATMEL LCD driver
This patch makes the necessary adaptations (PIO configurations and
defines in config header file) to hook up the Atmel LCD driver to the
AT91SAM9RLEK board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:45:02 +02:00
Stelian Pop
56a2479cd7 AT91SAM9263EK: hook up the ATMEL LCD driver
This patch makes the necessary adaptations (PIO configurations and
defines in config header file) to hook up the Atmel LCD driver to the
AT91SAM9263EK board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:45:02 +02:00
Stelian Pop
820f2a9583 AT91SAM9261EK: hook up the ATMEL LCD driver
This patch makes the necessary adaptations (PIO configurations and
defines in config header file) to hook up the Atmel LCD driver to the
AT91SAM9261EK board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:45:02 +02:00
Stelian Pop
c139b17d20 AT91CAP9ADK: hook up the ATMEL LCD driver
This patch makes the necessary adaptations (PIO configurations and
defines in config header file) to hook up the Atmel LCD driver to the
AT91CAP9ADK board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:45:02 +02:00
Stelian Pop
2118ebb44d AT91SAM9RLEK support
This patch adds support for the AT91SAM9RL chip and the AT91SAM9RLEK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:35:23 +02:00
Stelian Pop
8e429b3eee AT91SAM9263EK support
This patch adds support for the AT91SAM9263 chip and the AT91SAM9263EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:34:29 +02:00
Stelian Pop
d99a8ff66d AT91SAM9261EK support
This patch adds support for the AT91SAM9261 chip and the AT91SAM9261EK
board.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:08 +02:00
Stelian Pop
c1212b2f5c AT91SAM9260EK: Handle 8 or 16 bit NAND
The Atmel boards can handle 8 or 16 bit NAND memories. This patch
makes the support configurable in the board config header file
(CFG_NAND_DBW_8 or CFG_NAND_DBW_16).

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:07 +02:00
Stelian Pop
1c90df3e14 AT91CAP9ADK: Handle 8 or 16 bit NAND
The Atmel boards can handle 8 or 16 bit NAND memories. This patch
makes the support configurable in the board config header file
(CFG_NAND_DBW_8 or CFG_NAND_DBW_16).

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:06 +02:00
Stelian Pop
11b162bae0 Use a common u-boot.lds file across all AT91CAP9/AT91SAM9 platforms
All the AT91CAP9/AT91SAM9 boards have the same linker script. The patch
below avoids the duplication of u-boot.lds by putting the file in the
cpu directory instead of the board one.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:06 +02:00
Stelian Pop
d48abea4b8 Add proper copyright notices in Atmel boards Makefiles
The Makefiles for the AT91CAP9/AT91SAM9 boards have an incomplete
copyright notice. This patch adds the missing pieces.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:06 +02:00
Stelian Pop
e817a042ce Add copyright information in Atmel boards partition.c
When Ulf did the dataflash.c cleanup, he didn't add his copyright on
the new created files. This patch fixes the problem.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:32:06 +02:00
Stelian Pop
4f6c810106 Update origin and copyright information in arch-at91sam9 header files
When doing the AT91CAP9/AT91SAM9 port, a number of header files were
copied from the Linux kernel sources. This patch explicitly specifies
this origin for all the copied headers, and for those missing copyright
information, adds it.

Additionaly, the header file 'at91sam926x_mc.h' has been superceeded
in the latest kernel sources by 'at91sam9_smc.h'.

The copyright information has been confirmed by the AT91 Linux kernel
maintainer, Andrew Victor <avictor.za@gmail.com>.

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-10 11:30:13 +02:00
Stelian Pop
cce9cfdabc Fix @ -> <at> substitution
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.

The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-05-10 00:30:22 +02:00
Stelian Pop
9606b3c81b Update origin and copyright information in arch-at91sam9 header files
When doing the AT91CAP9/AT91SAM9 port, a number of header files were
copied from the Linux kernel sources. This patch explicitly specifies
this origin for all the copied headers, and for those missing copyright
information, adds it.

Additionaly, the header file 'at91sam926x_mc.h' has been superceeded
in the latest kernel sources by 'at91sam9_smc.h'.

The copyright information has been confirmed by the AT91 Linux kernel
maintainer, Andrew Victor <avictor.za@gmail.com>.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-05-10 00:28:51 +02:00
Stelian Pop
ceb6b4fbe1 Add copyright information in Atmel boards partition.c
When Ulf did the dataflash.c cleanup, he didn't add his copyright on
the new created files. This patch fixes the problem.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-05-10 00:24:02 +02:00
Stelian Pop
567fb85217 Fix @ -> <at> substitution
When applying the AT91CAP9 patches upstream, something transformed
the '@' character into the ' <at> ' sequence.

The patch below restores the original form in all the places where
it has been modified (the AT91CAP9 files, the AT91SAM9260 files which
were copied from AT91CAP9, and a couple of other files where the
' <at> ' sequence was present).

Signed-off-by: Stelian Pop <stelian@popies.net>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-05-08 23:40:42 +02:00
Ulf Samuelsson
c3a60cb3bd Clean up dataflash partitioning
This patch removes the board dependent parts from
"drivers/mtd/dataflash.c".
Each board relying on this, will have the appropriate
code in a new file, "partition.c" in the board directory.
board Makefiles updated to use the file.

The dataflash partitions are aligned on sector/page boundaries.

The CONFIG_NEW_DF_PARTITION was used to create named partitions
This is now the default operation, and the CONFIG variable is removed.

Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
2008-04-18 00:24:05 -07:00
Jean-Christophe PLAGNIOL-VILLARD
4e03dde84d AT91SAM9260EK: Move CONFIG_CMD_NAND to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-04-01 01:46:12 +02:00
Stelian Pop
0176d43e75 Add support for AT91SAM9260EK
Support for booting from internal DataFlash, external DataFlash card
or NAND flash is available.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-04-01 01:46:12 +02:00
Jean-Christophe PLAGNIOL-VILLARD
761712188b AT91CAP9ADK: Move CONFIG_CMD_NAND to Makefile
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-04-01 01:46:01 +02:00
Stelian Pop
983c1db04c Port AT91CAP9 to the new headers
Adapt the existing AT91CAP9 code to the new headers and APIs.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-04-01 01:45:50 +02:00
Jean-Christophe PLAGNIOL-VILLARD
64d792063f at91cap9adk: fix implicit declaration of function 'eth_init'
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
2008-02-17 16:03:20 +01:00
Peter Pearse
faf8f9bc95 Merge branch '080202_at91rm9200dk' of git://linux-arm.org/u-boot-armdev 2008-02-15 13:00:22 +00:00
Peter Pearse
ae92069abe Merge branch '080116_at91cap9' of git://linux-arm.org/u-boot-armdev 2008-02-15 12:59:15 +00:00
Haavard Skinnemoen
6523010702 Move AT91RM9200DK board support under board/atmel
We already have a vendor subdir for Atmel, so we should use it.

Signed-off-by: Haavard Skinnemoen <hskinnemoen <at> atmel.com>
2008-02-14 10:07:46 +00:00
Stelian Pop
64e8a06af6 AT91CAP9 support : move board files to Atmel vendor directory.
AT91CAP9 support : move at91cap9adk board files to Atmel vendor directory.

Signed-off-by: Stelian Pop <stelian@popies.net>
2008-02-14 09:37:58 +00:00
Haavard Skinnemoen
d38da53794 AVR32: Make SDRAM refresh rate configurable
The existing code assumes the SDRAM row refresh period should always
be 15.6 us. This is not always true, and indeed on the ATNGW100, the
refresh rate should really be 7.81 us.

Add a refresh_period member to struct sdram_info and initialize it
properly for both ATSTK1000 and ATNGW100. Out-of-tree boards will
panic() until the refresh_period member is updated properly.

Big thanks to Gerhard Berghofer for pointing out this issue.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-02-05 12:14:27 +01:00
Haavard Skinnemoen
61151cccb6 ATSTK1000: Fix potential flash programming bug
The (now obsolete) atngw100 flash programming code was having problems
programming the onboard at49bv642 chip. The atstk1000 flash
programming code may have the same bug, so import fix for this problem
from the AVR32 Linux BSP.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-02-05 12:14:27 +01:00
Haavard Skinnemoen
6b44394442 AVR32: ATNGW100 board support
Add support for the ATNGW100 Network Gateway reference design,
including flash, ethernet and MMC support.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-01-18 09:53:18 +01:00
Wolfgang Denk
64134f0112 Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections
With recent toolchain versions, some boards would not build because
or errors like this one (here for ocotea board when building with
ELDK 4.2 beta):
ppc_4xx-ld: section .bootpg [fffff000 -> fffff23b] overlaps section .bss [fffee900 -> fffff8ab]

For many boards, the .bss section is big enough that it wraps around
at the end of the address space (0xFFFFFFFF), so the problem will not
be visible unless you use a 64 bit tool chain for development. On
some boards however, changes to the code size (due to different
optimizations) we bail out with section overlaps like above.

The fix is to add the NOLOAD attribute to the .bss and .sbss
sections, telling the linker that .bss does not consume any space in
the image.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-01-12 20:31:39 +01:00
Haavard Skinnemoen
7b624ad254 AVR32: Initialize bi_flash* in board_init_r
The ATSTK1000-specific flash driver intializes bi_flashstart,
bi_flashsize and bi_flashoffset, but other flash drivers, like the CFI
driver, don't.

Initialize these in board_init_r instead so that things will still be
set up correctly when we switch to the CFI driver.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-10-06 20:17:37 +02:00
Jon Loeliger
fcec2eb93e board/[A-Za-c]*: Remove obsolete references to CONFIG_COMMANDS
Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-09 18:47:45 -05:00
Jon Loeliger
5e378003d5 board/[Ma-i]*: Augment CONFIG_COMMANDS tests with defined(CONFIG_CMD_*).
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.

All transformations are of the form:
Before:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
    #if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)

Signed-off-by: Jon Loeliger <jdl@freescale.com>
2007-07-04 00:34:58 +02:00
Haavard Skinnemoen
8e6875183c AVR32: Enable MMC support
Set up the portmux for the MMC interface and enable the MMC driver
along with support for DOS partitions, ext2 and FAT filesystems.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14 16:14:06 +02:00
Haavard Skinnemoen
9a24f477a1 AVR32: Enable networking
Implement MACB initialization for AVR32 and ATSTK1000, and turn
everything on, including the MACB driver.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14 16:14:06 +02:00
Haavard Skinnemoen
12f099c081 AVR32: Use initdram() instead of board_init_memories()
Conform to the "standard" interface and use initdram() instead of
board_init_memories() on AVR32. This enables us to get rid of the
sdram_size member of the global_data struct as well.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14 15:20:27 +02:00
Haavard Skinnemoen
1f4f2121c2 AVR32: Relocate u-boot to SDRAM
Relocate the u-boot image into SDRAM like everyone else does. This
means that we can handle much larger .data and .bss than we used to.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14 15:20:27 +02:00
Haavard Skinnemoen
df548d3c3e AVR32: Resource management rewrite
Rewrite the resource management code (i.e. I/O memory, clock gating,
gpio) so it doesn't depend on any global state. This is necessary
because this code is heavily used before relocation to RAM, so we
can't write to any global variables.

As an added bonus, this makes u-boot's memory footprint a bit smaller,
although some functionality has been left out; all clocks are enabled
all the time, and there's no checking for gpio line conflicts.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2007-04-14 15:20:27 +02:00
Wolfgang Denk
d38936cdae Fix "ar" flags in some Makefiles to allow for silent "make -s" 2006-10-27 11:55:21 +02:00
Haavard Skinnemoen
5e3b0bc19f Finish up support for the ATSTK1000/ATSTK1002 boards
Add atstk1002_config target to Makefile and move the AVR32 section
down below Blackfin so that it doesn't end up in the middle of
MIPS.

Drop the autogenerated linker script thing for now. Will have to
revisit how to handle chips with different flash and RAM layout
later.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2006-10-25 23:44:48 +02:00
Wolfgang Denk
3a78e3e75b Move atstk1000 files into vendor specific directory.
Patch by Haavard Skinnemoen, 12 Sep 2006
2006-10-24 14:51:36 +02:00