Fix Coverity Issue 9006656. In nandbcb_set_boot_config, an integer overflow
occurs, with the result converted to a wider integer type.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006658. In fill_dbbt_data, an integer overflow occurs,
with the result converted to a wider integer type
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006657. In read_fcb, leak of memory to system
resource "fcb_raw_page". Adjust the sequence to check the mtd bad
block prior than allocation of "fcb_raw_page", also check the NULL
return of allocation.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006655. In write_fcb, leak of memory to resource
"fcb_raw_page". Since we have initialized the "ret" to 0, should return
the value of ret.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity Issue 9006654. In write_fcb, use of an uninitialized
variable "ret".
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
use CONFIG_TARGET_IMX8MN_DDR4_EVK for DDR4 EVK board, we will use
CONFIG_TARGET_IMX8MN_EVK for LPDDR4 EVK board.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The dm root node is needed early in the spl to allow the timer to be
used. This change calls spl_early_init to initialize the dm root node.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
Giant board is a tiny SBC based on the Adafruit Feather form factor,
created by groboards it contains a SAMA5D2 processor (SAMA5D27),
128 MB of RAM and a microSD card for storage.
Signed-off-by: Greg Gallagher <greg@embeddedgreg.com>
Because ATMEL_BASE_ROM is defined to 0x100000, it already points
to the begin of the index table for 512 byte sectors correction.
Thus its offset must be zero and the index of the table for 1024
byte sectors must start at offset 0x8000.
Signed-off-by: Kai Stuhlemmer (ebee Engineering) <kai.stuhlemmer@ebee.de>
[ta: update commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Offsets are described in the datasheet at section:
"11.4.4.2 NAND Flash Boot: PMECC Error Detection and Correction".
For testing I "injected" bit flips into u-boot NAND memory area,
and then read back. PMECC could not correct the errors. With the
offsets updated everything is fine.
Fixes: 3225f34e5c ("ARM: atmel: add sama5d3xek support")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
This adds support for the NanoPi R2S from FriendlyArm.
Rockchip RK3328 SoC
1GB DDR4 RAM
Gigabit Ethernet (WAN)
Gigabit Ethernet (USB3) (LAN)
USB 2.0 Host Port
MicroSD slot
Reset button
WAN - LAN - SYS LED
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
The rng is embedded in the SoC so enable it in the device tree
universally, the use of it can be controlled by enabling/disabling
at the device config level.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0. Formerly the alias spi1
pointed to &spi5, use an alias spi5 for this instead.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
SPI flash on this board is located on bus 1, default to using bus 1 for
SPI flash on both rk3399-roc-pc and -mezzanine, and stop aliasing it to
bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Add low level platform initialization for the AST2600 SoC.
The 2-stage booting with U-Boot SPL are leveraged to support
different booting mode.
However, currently the patch supports only the booting from
memory-mapped SPI flash.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 is the 7th generation of Aspeed SoC designated for
Interated Remote Management Processor.
AST2600 has significant performance improvement by integrating
1.2GHz dual-core ARM Cortex A7 (r0p5) CPU with FPU. Most of the
controllers are also improved with more features and better
performance than preceding AST24xx/AST25xx.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 has 8 watchdog timers including 8 sets of
32-bit decrement counters, based on 1MHz clock.
A 64-bit reset mask is also supported to specify
which controllers should be reset by the WDT reset.
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
AST2600 supports DDR4 SDRAM with maximum speed DDR4-1600.
The DDR4 DRAM types including 128MbX16 (2Gb), 256MbX16 (4Gb),
512MbX16 (8Gb), 1GbX16 (16Gb), and 1GbX8 TwinDie (16Gb) are supported.
Signed-off-by: Dylan Hung <dylan_hung@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Reviewed-by: Ryan Chen <ryan_chen@aspeedtech.com>
This patch adds the clock control driver
for the AST2600 SoC.
Signed-off-by: Ryan Chen <ryan_chen@aspeedtech.com>
Signed-off-by: Chia-Wei, Wang <chiawei_wang@aspeedtech.com>
Set environment for Nand flash (U-boot 2020.04):
- add nand flash in the device tree
- add new default configuration file for G3 using parallel Nand
- set nand parameters in presidio_asic.h
Signed-off-by: Kate Liu <kate.liu@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The pci_mmc.c driver can generate ACPI info and therefore includes
asm/acpi_table.h by proxy. This file does not exist for the ARM
architecture and thus code compilation failed when using this
driver on ARM.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
CC: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
QEMU.
Signed-off-by: Harm Berntsen <harm.berntsen@nedap.com>
Remove the leading "0x" from rpc node to fix the below dtc warning:
Warning (simple_bus_reg): Node /soc/rpc@0xee200000 simple-bus unit
address format error, expected "ee200000"
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Add a return value to noncached_init and use it directly in the
post-relocation init sequence, rather than using a wrapper stub.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add binman node to device tree to generate the FIT image for u-boot
(u-boot.itb) and OS kernel (kernel.itb).
u-boot.itb contains arm trusted firmware (ATF), u-boot proper and
u-boot device tree for ATF u-boot flow.
kernel.itb contains Linux Image and Linux device tree.
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
SPL already setup the Clock Manager with the handoff data
from OCRAM. When the Clock Manager's driver get probed again
in SSBL, it shall skip the handoff data access in OCRAM.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
In non-secure mode (EL2), Reset Manager driver calls the
SMC/PSCI service provided by ATF to enable/disable the
SOCFPGA bridges.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Signed-off-by: Siew Chin Lim <elly.siew.chin.lim@intel.com>
invoke_smc() allow U-Boot proper running in non-secure mode (EL2)
to invoke SMC call to ATF's PSCI runtime services such as
System Manager's registers access, 2nd phase bitstream FPGA
reconfiguration, Remote System Update (RSU) and etc.
smc_send_mailbox() is a send mailbox command helper function which invokes
the ATF's PSCI runtime service (function ID: INTEL_SIP_SMC_MBOX_SEND_CMD)
to send mailbox messages to Secure Device Manager (SDM).
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Standard PSCI function "CPU_ON" provided by ATF is now used
by Linux kernel to bring up the secondary CPUs to enable SMP
booting in Linux on SoC 64bits platform.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Override 'lowlevel_init' to make sure secondary CPUs trapped
in ATF instead of SPL. After ATF is initialized, it will signal
the secondary CPUs to jump from SPL to ATF waiting to be 'activated'
by Linux OS via PSCI call.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Add board_fit_config_name_match() for matching board name with
device tree files in FIT image. This will ensure correct DTB
file is loaded for different board type. Currently, we are not
supporting multiple device tree files in FIT image therefore this
function basically do nothing for now.
Users are allowed to override this 'weak' function in their
specific board implementation.
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/+yLkACgkQ4rK92eCq
k3X/Fgf/d/11WyQrVzvpr+nN+4Wl7J+ASmoUz0yKa6ri+lbvhLgh+JXbCRKgRPWu
vNnI07pSoX/QeaMpGBU8Ztg/Onb9/pvffz4WMk1411GoyCpDFuuK3cVSIoqkPfu+
XmgSX0u4BXtve1+ZdWfVBWXawUSEDMmGR3tmz1708c/s/oYpnVeRDcqiqzJ94cWE
yt+SpMPVqMUVQ/rAGkE8ToSMxX7FusEa7SvCg4U2ikoRWs3kPpr/73+tRWlmgGxL
sW8SXSKiOmFyheSBx3d2B9n00kDYTTrQmbW9hlMilZmji7CwZYxgTCMdX0x4DeFP
RDajT2Yju1JmeM+Z8+Ke2tupzvy6QA==
=oK8C
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210113' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Enable logging features for stm32mp15 boards
- Update MAINTAINERS emails for STI and STM32
- Activate OF_LIVE for ST stm32mp15 boards
- Switch to MCO2 for PHY 50 MHz clock for DHCOM boards
- Correction in stm32prog command on uart: always flush DFU on start command
- Update USB-C power detection algorithm on DK boards
A previous series already update STMicroelectronics emails maintainers
but some files have been omitted (Makefile, .dts, .dtsi and .rst files).
Update Patrick and my email address with the one dedicated to upstream
activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove the test on data->dfu_seq, because dfu_seq=0 not only when
the DFU is not started (mask with 0xffff). This flush is mandatory
as the final treatment, common with USB, is done in DFU callback.
This patch avoids issue if the received length is a multiple of
the DFU packet.
For example if size of bootfs partition is egual to 0x4000000,
data->dfu_seq=0 at the end of the partition, the flush it not
requested and the phase is not increased in the callback.
U-Boot continue to request the bootfs in the next GetPhase command.
Fixes: 468f0508b5 ("stm32mp: stm32prog: add serial link support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
The LAN8710i PHY currently uses 50 MHz clock direct from PLL4P.
To permit PLL4P to run at faster frequency, use MCO2 as a divider.
The PLL4P runs at 100 MHz, supplies MCO2 which divides it by 2 to
50MHz, and supplies the PHY with 50 MHz via pin PG2. The feedback
clock are fed back in via pin PA1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Change-Id: Ia9bf7119785d49b633a3ae761c3dc4a30b92628a
Define LOG_CATEGORY, change pr_debug to dev_dbg and remove "bsec:"
header as it is managed by log macro (dev->name is displayed)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Change debug and pr_ macro to log macro and define LOG_CATEGORY.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Remove board_mmc_init function.
It will be probed with driver-model.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/8S/0cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyKFkB/9NBJq/+sgHZXRaMlAu
ULNwOPoNsQxHQGwF88B1lC+H8LJjM+2gJ8MfJdWvHNlcSdtJjbWk0aQL+5LKSlyz
G7l3BZ+AIYMOeTXay5mNUKnekXIr7c8tLoX8FH/Ih+bHFPt57qL0bbfznV66UCOp
/o/yM8daPa9Kx1vPEpT2dC9bYXLXeQv6R+RMxwoc4Bk+R3OK7zoZ3Wdx0q9HvBwj
iWHM49X2fBqqi5RS+ZI37AUzi8iysD3fOq0kWTJcCNaci8i8RZdzSyoaDuXhA63I
EZJ7v9fUkW/bwTONVE9n2BX4xF9X/6R7P46l9dQISXAxsOBwsNRQPt8Ro7mCoc4K
392o
=LIK7
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features for 2021.04 cycle
This feature set includes the new board SAMA7G5 EK, the new evaluation
kit for Microchip AT91 SAMA7G5 SoC . The current board support includes
two configurations for booting from eMMC (SDMMC0), SD-Card (SDMMC1), and
support for two Ethernet interfaces.
Enabling the domain clock is performed by the sysc interconnect target
module driver during the video device probing.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The previous version of am335x-fb.c contained the functionalities of two
drivers that this patch has split. It was a video type driver that used
the same registration compatible string that now registers a panel type
driver. The proof of this is that two compatible strings were referred
to within the same driver.
There are now two drivers, each with its own compatible string,
functions and API.
Furthermore, the panel driver, in addition to decoding the display
timings, is now also able to manage the backlight.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Up till this commit passing NULL as input parameter was allowed, but not
handled properly. When a NULL parameter was passed to the function a data
abort was raised.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
There have been several changes to the am33xx.dtsi, so this patch
re-syncs it with Linux.
Let's add proper interconnect hierarchy for l4 interconnect instances
with the related ti-sysc interconnect module data as documented in
Documentation/devicetree/bindings/bus/ti-sysc.txt of the Linux kernel.
With l4 interconnect hierarchy and ti-sysc interconnect target module
data in place, we can simply move all the related child devices to their
proper location and enable probing using ti-sysc.
The am33xx-clock.dtsi file is the same as that of the Linux kernel,
except for the reg property of the node l4-wkup-clkctrl@0.
As for the am33xx.dtsi file, all the devices with drivers not yet
implemented and those I was able to test with this patch have been moved
to am33xx-l4.dtsi. In case of any regressions, problem devices can be
reverted by moving them back and removing the related interconnect
target module node.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
We can handle the sysc interconnect target module in a generic way for
many TI SoCs. Initially let's just enable domain clocks before the
children are probed.
The code is loosely based on the drivers/bus/ti-sysc.c of the Linux
kernel version 5.9-rc7.
For DT binding details see:
- Documentation/devicetree/bindings/bus/ti-sysc.txt
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Update the ddr settings to use the DDR reg config tool rev 0.5.0.
This enables 4266MTs DDR configuration.
Signed-off-by: Praneeth Bajjuri <praneeth@ti.com>
Signed-off-by: Kevin Scholz <k-scholz@ti.com>
The sequence number assigned for USB subsystem in a uclass is dependent on
the order of occurrence in the device tree. If the dr_mode of USB3SS0
controller is varied then the sequence number of USB3SS1 controller also
changes. If aliases are added then sequence numbers are assigned using the
alias number. This makes the sequence number of USB3SS1 controller
independent of USB3SS0 controller's dr_mode.
Therefore, add aliases to fix the sequence number assigned to the USB
subsystems.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Some Bluetooth controllers, like the BCM4345C5 of the Orange Pi 3,
ship with the controller default address.
Add a config option to fix it up so it can function properly.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
[rebased]
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
It turns out that in rare cases, current analytical approach to detect
correct DRAM bus width and rank on H6 doesn't work. On some TV boxes
with DDR3, incorrect DRAM configuration triggers write leveling error
which immediately stops initialization process. Exact reason why this
error appears isn't known. However, if correct configuration is used,
initalization works without problem.
In order to fix this issue, simply try another configuration when any
kind of error appears during initialization, not just those related to
rank and bus width.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Tested-by: Thomas Graichen <thomas.graichen@googlemail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
For the sake of consistency (*) and order of initialization, i.e.
after we have got the ethernet address, interrupt and timer initialized,
try to initialize USB ethernet gadget.
*) for example, zynqmp uses same order.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far we did not support the BootROM based FEL USB debug mode on the
64-bit builds for Allwinner SoCs: The BootROM is using AArch32, but the
SPL runs in AArch64.
Returning back to AArch32 was not working as expected, since the RMR
reset into 32-bit mode always starts execution in the BootROM, but not
in the FEL routine.
After some debug and research and with help via IRC, the CPU hotplug
mechanism emerged as a solution: If a certain R_CPUCFG register contains
some magic, the BootROM will immediately branch to an address stored in
some other register. This works well for our purposes.
Enable the FEL feature by providing early AArch32 code to first save the
FEL state, *before* initially entering AArch64.
If we eventually determine that we should return to FEL, we reset back
into AArch32, and use the CPU hotplug mechanism to run some small
AArch32 code snippet that restores the initially saved FEL state.
That allows the normal AArch64 SPL build to be loaded via the sunxi-fel
tool, with it returning into FEL mode, so that other payloads can be
transferred via FEL as well.
Tested on A64, H5 and H6.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> (on Olimex A64-Olinuxino)
The is_boot0_magic macro is missing parentheses around the macro
argument, breaking any usage with a more complex argument.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To be able to easily share the Allwinner eGON BROM header structure
between the tools and the SPL code, move the struct definition into a
separate header file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
PineCube is an IP camera development kit released by Pine64.
It comes with the following compoents:
- A mainboard with Sochip S3 SoC, a 16MByte SPI Flash, AXP209 PMIC,
a power-only microUSB connector, a USB Type-A connector, a 10/100Mbps
Ethernet port and FPC connectors for camera and daughter board.
- An OV5640-based camera module which is connected to the parallel CSI
bus of the mainboard.
- A daughterboard with several buttons, a SD slot, some IR LEDs, a
microphone and a speaker connector.
As the device tree is synchronized in a previous commit, just add it to
Makefile, create a new MAINTAINER item and provide a defconfig.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Import the Beelink GT-King/Pro and supporting meson-g12b-w400.dtsi file
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import the WeTek Core2 and supporting meson-gx-p23x-q20x.dtsi files
from Linux 5.10.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SoC revision to environment. This can be useful to select the
correct device tree at runtime (N2/N2+).
Signed-off-by: Pascal Vizeli <pvizeli@syshack.ch>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Move loading of socinfo into a separate function so the value can be
reused later.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic based libretech cc version 2.
As version 1, it is based on the s905x SoC.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
[narmstrong: Fixed libretech-cc.rst bullet points]
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Sync the libretech cc v2 device tree from Linux v5.10-rc1
commit 3650b228f83a ("Linux 5.10-rc1")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
SPI flash on this machine is located on bus 1, default to using bus 1
for SPI flash and stop aliasing it to bus 0.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bb ("rockchip: Enable building a SPI ROM image on bob")
TXC line is directly connected from the SoC to the KSZ9131 PHY. There
is a transient state on this signal, before configuring it to RGMII,
which leads to packet transmit being blocked.
Keeping a pull-up when muxing this pin as function A (G0_TXCK) fixes
the issue.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Add node for flx1 i2c1 subnode (and alias to bus 0)
This bus has two eeprom devices connected.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Enable sdmmc0 on this board. A non-removable eMMC is connected on this
block.
Configure pincontrol accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
SDMMC1 requires clock specification with assigned-clocks, such that
the PMC will know which parent to assign and the initial start-up frequency.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Get rid of software defined MCK and switch to PMC bindings
for IPs currently present in device tree.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Since GPIO_ACTIVE_HIGH is defined as 0, this change only increases the
correctness of the DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The GPIO hog flags are ignored by gpiolib-of.c now, set the flags to 0.
Due to a change in gpiolib-of.c, setting flags to GPIO_ACTIVE_LOW and
using output-low DT property leads to the GPIO being set high instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
=9kN3
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next
Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
In the spirit of using the same base name for all of these related macros,
rename this to have the operation at the end. This is not widely used so
the impact is fairly small.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.
The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)
It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.
Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode is present in the device even if it is never used. With
of-platdata this field is not used, so can be removed. In preparation for
this, change the access to go through inline functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most drivers use these access methods but a few do not. Update them.
In some cases the access is not permitted, so mark those with a FIXME tag
for the maintainer to check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Pratyush Yadav <p.yadav@ti.com>
This uses up space in the SPL binary but it always starts as zero. Also
some boards cannot support data in TPL (e.g. Intel Apollo Lake).
Use malloc() to allocate this structure instead, by moving the init a
little later, after malloc() is inited. Make this function optional since
it pulls in malloc().
This reduces the TPL binary size on coral by about 64 bytes
Signed-off-by: Simon Glass <sjg@chromium.org>
Lower case should be used for function names. Update this driver and its
callers accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Typedefs should not be used in U-Boot and structs should be lower case.
Update the code to use struct ns16550 consistently.
Put a header guard on the file while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
This patch add ethernet node gem1 to zcu1285 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch add ethernet node gem1 to zcu1275 RevB.
GMII to RGMII converter sits between MAC and external
phy connected over GMII to MAC and RGMMI to external phy.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On the qemu arm platform, the virtio devices are initialised in the
board_init function, which gets called before the initr_pci. With
this sequence, the virtio block devices on the pci bus are not
initialised. Move the initialisation of the virtio devices to
board_late_init which gets called after the call to initr_pci.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
For correct spi bus detection the spi0 alias is needed in the DT.
Otherwise this error will ocurr in U-Boot:
Invalid bus 0 (err=-19)
Failed to initialize SPI flash at 0:0 (error -19)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Add some missing "u-boot,dm-pre-reloc;" properties to UART0, SPI
controller and SPI NOR flash node to enable usage in SPL. Otherwise
these devices will not be available.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dennis Gilmore <dgilmore@redhat.com>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Use %u and not %d for unsigned values.
Print kHz and not khz.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The dart6ul has an i2c eeprom at 0x50 which contains, among other
things, the manufacturing/revision/options info of the SoM. This patch
replaces the current checkboard() implementation with a more
exhaustive one based on the content of the eeprom.
Since this code uses the new driver model, some changes were also
required in the DTS to make the nodes related to i2c available before
relocation.
This code was inspired from the supported u-boot code from Variscite
which can be found here:
https://github.com/varigit/uboot-imx/tree/imx_v2018.03_4.14.78_1.0.0_ga_var02
New output example:
Board: PN: VSM-6UL-705B, Assy: AS1812142257, Date: 2019 Feb 17
Storage: eMMC, Wifi: yes, DDR: 1024 MiB, Rev: 2.4G
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The eeprom at address 0x50 is a BR24G04NUX-3TTR. It has a
4Kbit (512x8) capacity, change the compatible string to reflect this
fact.
Also, add an alias to easily refer to this eeprom with
fdt_path_offset() which will be in another commit.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Calling ahab_close cmd force the user to interact for confirmation.
This is not user-friendly when using this cmd during factory process.
Allow the user to pass '-y' option to bypass this confirmation.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
The current PHY rework does the following things:
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.
Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fixed wrong PHY Interface Mode
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
Now that there is only one sequence number (rather than both requested and
assigned ones) we can simplify this function. Also update its caller to
simplify the logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present various drivers etc. access the device's 'seq' member directly.
This makes it harder to change the meaning of that member. Change access
to go through a function instead.
The drivers/i2c/lpc32xx_i2c.c file is left unchanged for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead if the
ACTIVE_HIGH, what will leave the pin in input to achieve high state (pin
has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This name is far too long. Rename it to remove the 'data' bits. This makes
it consistent with the platdata->plat rename.
Signed-off-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl/TlVUcHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyK8eB/9mIJCgCiDue2ytkUg+
fyJHHtHf+rFIbvLiR+iVy/2rXlsjfXwNVyJTswJOCucit0cf+F7fh6vi/AnOoDnE
Zezj9ngm+25fvffQjt0T74V2w+GhT5OXqR7ctpIcrmKun2UTujSA9NQqRaLFDI9x
RQlUXsCzLypFZRXvyOCo34Nz7MZ1QvIAKxEJyYb7ft/qnbtILDr0p54xxjlK5B/W
s+MP05qaRmup9rk33JwfLmeyjTmDBuri0rBh/2XKFtszJBm5CdgXJEqNY+22JzJF
xlqfobmdPn77+JH36B/KJgDmrrL05vv+RyvOPoBNzm6BEKtlflcSf9NnTKlSud4y
w/50
=r687
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2021.01-b' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel fixes for 2021.01 cycle
This set includes very important fixes for: MMC booting on several
boards, drive strength on sam9x60ek mmc lines, compile issues for
timer.c old driver, removal of unwanted access to sam9x60 bit for
oscillator bypass mode, and eeproms read on sama5d2_icp.
The correct compatible for this eeproms is microchip,24aa02e48
The previous compatible string was working up to U-boot 2020.04.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Tested-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
The USB support is not by default enabled on all designs, so it does not
make seance to have USB specific erratum's enabled on such a designs.
On our internal Hitachi-Powergrids design not using the USB controller
there is a crash when accessing those specific memory locations selected
by the erratum flags.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachi-powergrids.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When booting from TF-A there is a logic that attempt to detect if the
default environment is used, if this is the case it then set the
`bootcmd` and `mcinitcmd` depending of the device we booted from.
This detection logic is dubious as it access internals of the env
implementation and it doesn't always work correctly.
First of all it detect any valid environment as not being the
default, so after running `env default -a && saveenv` the board
doesn't boot anymore as `bootcmd` is then empty.
But it also fails in some other ways, for example it always detect a
default environment when redundant env is enabled on MMC, so in that
case `bootcmd` is overwritten on every boot.
Instead of increasing the complexity of the detection just check if
`bootcmd` and `mcinitcmd` are set in the environment and set them if
they are not.
Signed-off-by: Alban Bedel <alban.bedel@aerq.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Check for NULL return value from fdt_getprop() in
fdt_fixup_remove_jr()
Signed-off-by: Priyanka Singh <priyanka.singh@nxp.com>
[Fixed checkpatch errors/warnings]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LX2162 is LX2160 based SoC, it has same die as of LX2160
with different packaging.
LX2162A support 64-bit 2.9GT/s DDR4 memory, i2c, micro-click module,
microSD card, eMMC support, serial console, qspi nor flash, qsgmii,
sgmii, 25g, 40g, 50g network interface, one usb 3.0 and serdes
interface to support three PCIe gen3 interface.
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
[Fixed whitespace errors]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add label to pcie nodes in dts so that these nodes
are easy to refer.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl/Q5aAACgkQ4rK92eCq
k3XuqAgAifJcb3NxKmWa4eFDbZpWZ1R8h6FPp6vlmvyC4C3otRHEe5WrYCsAeqy1
Gs311dtdluc4y5Ltmf54OcN7ICfLsSiOvye85f5myhPj1v4d1F1Z70X0FDo/o9hE
7TEZfWBQtNjXI4F23+vaDT4jCvUZV1LR6Lab/zLLw1/uLUxxS799kcFiWgHLuEoH
8Cv0JbgzLuuVk5lyLJ+DFZOcntwWu5+Qm+l5eS46armbKphMFh5KPJ9PG81eJE3N
zsCpavEs4nuQl7wGF8HPfDWxz5Xef6ip3A4Owh92t3WQWKxp1bSUKqDeKZTkhIyS
LSJKe9CQ9+zCS3m3Utoi1pVt1EbFrQ==
=cgbE
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20201209' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Manage CONFIG_ENV_EXT4_DEVICE_AND_PART in stm32mp1 board
- Update ARM STI and ARM STM STM32MP Arch maintainers emails
- Enable internal pull-ups for SDMMC1 on DHCOM SoM
Add USB OTG ID pin mux and switch the USB OTG port
from peripheral to OTG mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The DH DRC02 board has an on-board microSD slot,
add DT properties to enable the slot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The STM32MP1 DHCOM SoM can be built with either bus voltage level shifter
or without one on the SDMMC1 interface. Because the SDMMC1 interface is
limited to 50 MHz and hence SD high-speed anyway, disable the SD feedback
clock to permit operation of the same U-Boot image on both SoM with and
without voltage level shifter.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
The default state of SD bus and clock line is logical HI. SD card IO is
open-drain and pulls the bus lines LO. Always enable the SD bus pull ups
to guarantee this behavior on DHCOM SoM. Note that on SoMs with SD bus
voltage level shifter, the pull ups are built into the level shifter,
however that has no negative impact.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Update Patrick and my email address with the one dedicated to
upstream activities.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
- Espressobin: Simplify DT handling of board variants (Pali)
- Add Luka Perkov to maintainers of Puzzle-M801 (Luka)
- Armada 38x: Enable board specific USB2 high-speed impedance
threshold configuration (Joshua)
To simplify setup, configuration and compilation of u-boot, define emmc
node for all Espressobin boards. Espressobin boards without populated emmc
works correctly, just detection and initialization of emmc obviously fails.
Code for emmc is extracted from commit f1a43c84a9 ("arm64: dts: a3720:
add support for espressobin with populated emmc").
Signed-off-by: Pali Rohár <pali@kernel.org>
Tested-by: Gérald Kerma <gerald@gk2.net>
Hardware testing of a board using the Armada 385 has shown that an
impedance threshold setting of 0x7 performs better in an eye-diagram
test than with Marvell's recommended value 0x6.
As other boards may still perform better with Marvell's reccomended value,
a configuration option is added with a default value of 0x6.
Signed-off-by: Joshua Scott <joshua.scott@alliedtelesis.co.nz>
Reviewed-by: Stefan Roese <sr@denx.de>
Introduce weak function board_mem_get_layout() which allows overriding
the memory layout from board code in runtime, useful for handling
different SKU versions.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Introduce initial hierarchy of device trees for Apalis iMX8X
System on Module.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
the mem_map structure containing the size of SDRAM is used in various
cache functions in cache_v8.c thus we need to update it with the
sdram size the board is configured with as well. Without this
the cache functions do not get setup properly and can hang
in the case where a board reports more SDRAM than defined in
PHYS_SDRAM_SIZE.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The used PMIC has been changed from RHOM BD71837 to NXP PCA9450A.
Adjust the device tree accordingly.
Remove the old ADC node as the ADC has been changed and has no longer
a separate power rail.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reduce vital product data size to match the latest specification.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Fix the following warning:
arch/arm/mach-imx/imx8/ahab.c:105:3: warning: implicit declaration of function ‘flush_dcache_range’ [-Wimplicit-function-declaration]
flush_dcache_range(s, e);
^~~~~~~~~~~~~~~~~~
Include cpu_func.h header which declares the flush_dcache_range()
function.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c: In function ‘authenticate_os_container’:
arch/arm/mach-imx/imx8/ahab.c:96:9: warning: format ‘%x’ expects argument of type
‘unsigned int’, but argument 9 has type ‘ulong {aka long unsigned int}’ [-Wformat=]
debug("img %d, dst 0x%x, src 0x%x, size 0x%x\n",
Fix those by using "%lu" specified.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
arch/arm/mach-imx/imx8/ahab.c:110:63: warning: format ‘%x’ expects
argument of type ‘unsigned int’, but argument 2 has type ‘u64 {aka long
long unsigned int}’ [-Wformat=]
Fix those by using %llx
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: uboot-imx <uboot-imx@nxp.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
The BL31 expects the GIC to be uninitialized. Thus, if we are loading
the BL31 by the SPL we must not initialize it. If u-boot is loaded by
the SPL directly, it will initialize the GIC again (in the same
lowlevel_init()).
This was tested on a custom board with SPL loading the BL31 and jumping
to u-boot as BL33 as well as loading u-boot directly by the SPL. In case
the ATF BL1/BL2 is used, this patch won't change anything, because no
SPL is used at all.
Signed-off-by: Michael Walle <michael@walle.cc>
There is SPL_ARMV8_SEC_FIRMWARE_SUPPORT and ARMV8_SEC_FIRMWARE_SUPPORT.
Thus use CONFIG_IS_ENABLED() instead of the simple #ifdef.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Activate ARCH_SUPPORT_PSCI as other TEGRA124 target and remove
CONFIG_ARMV7_PSCI and CONFIG_ARMV7_PSCI_NR_CPUS in configs file as they
are migrated in Kconfig.
Select CONFIG_ARMV7_PSCI_0_1 (the first PSCI version),
because CONFIG_ARMV7_PSCI_0_2 and CONFIG_ARMV7_PSCI_1_0
are not activated in this product.
Hi,
This patch depend on the previous serie [1].
I don't test this patch on real hardware but
after this patch the size of the binary don't change.
In .config we have:
CONFIG_ARCH_SUPPORT_PSCI=y
CONFIG_ARMV7_PSCI=y
# CONFIG_ARMV7_PSCI_1_0 is not set
# CONFIG_ARMV7_PSCI_0_2 is not set
CONFIG_ARMV7_PSCI_0_1=y
CONFIG_ARMV7_PSCI_NR_CPUS=4
In u-boot.cfg, this patch only add the 2 lines
#define CONFIG_ARCH_SUPPORT_PSCI 1
#define CONFIG_ARMV7_PSCI_0_1 1
[1] "Convert CONFIG_ARMV7_PSCI_1_0 and CONFIG_ARMV7_PSCI_0_2 to Kconfig"
http://patchwork.ozlabs.org/project/uboot/list/?series=184029
Regards
Patrick
END
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Peter Chubb <peter.chubb@data61.csiro.au>
Signed-off-by: Tom Warren <twarren@nvidia.com>
USB clocks were completely forgotten as driver would always return 0 even if clock ID was unknown.
This behaviour changed with "IPQ40xx: clk: dont always return 0" and this will now causes the USB-s to fail probing as clock enable will return -EINVAL.
So to fix that lets add all of the USB clocks to the driver.
Fixes: 430e1dcf ("IPQ40xx: Add USB nodes")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Currently the driver will go through the clock ID-s and set/enable them as needed.
But if the ID is unknown it will fall through the switch case to the default case which will always return 0.
This is not correct and default cases should return a error code since clock ID is unknown.
So lets return -EINVAL instead.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
There is no point in having break statements in the switch case as there is already a return before break.
So lets drop them from the driver.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Lets convert the driver to use dev_read_addr() instead of the devfdt_get_addr().
While we are here, lets also alphabetise the includes.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
The AT91 architecture now has two possible timer blocks, the old PIT timer
and the new PIT64B.
The timer.c file has an old non DM driver that works for platforms
that do not use the ATMEL_PIT_TIMER DM-based driver.
Update the Makefile to select this old driver in case neither of the
ATMEL_PIT_TIMER and the MCHP_PIT64B_TIMER are selected.
Suggested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>