Add device data for main_uart1 in dev-data.c for J7200. Now,
main_uart1 will be powered on while booting the J7200 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
When selecting UDA partition for booting. MMC read
mode was selected as RAW.
Due to growing/changing size of u-boot and tispl
images.
It will be better change to FS in case of UDA FS instead of
adjusting offsets with new change.
Signed-off-by: Udit Kumar <u-kumar1@ti.com>
Add main_uart5 clocks in clk-data.c for J721S2. Now,
main_uart5 clocks will be set up while booting the J721S2 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add device data for main_uart5 in dev-data.c for J721S2. Now,
main_uart5 will be powered on while booting the J721S2 SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add main_uart2 clocks in clk-data.c for J721E. Now,
main_uart2 clocks will be set up while booting the J721E SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Add device data for main_uart2 in dev-data.c for J721E. Now,
main_uart2 will be powered on while booting the J721E SoC.
Signed-off-by: Bhavya Kapoor <b-kapoor@ti.com>
Compiling with gcc 13 results in an error:
drivers/axi/axi-emul-uclass.c:16:5: warning: conflicting types for
‘axi_sandbox_get_emul’ due to enum/integer mismatch; have
‘int(struct udevice *, ulong, enum axi_size_t, struct udevice **)’
{aka ‘int(struct udevice *, long unsigned int, enum axi_size_t,
struct udevice **)’} [-Wenum-int-mismatch]
16 | int axi_sandbox_get_emul(struct udevice *bus, ulong address,
| ^~~~~~~~~~~~~~~~~~~~
In file included from drivers/axi/axi-emul-uclass.c:14:
./arch/sandbox/include/asm/axi.h:48:5: note: previous declaration of
‘axi_sandbox_get_emul’ with type ‘int(struct udevice *, ulong, uint,
struct udevice **)’ {aka ‘int(struct udevice *, long unsigned int,
unsigned int, struct udevice **)’}
48 | int axi_sandbox_get_emul(struct udevice *bus, ulong address, uint length,
| ^~~~~~~~~~~~~~~~~~~~
Adjust the header definition to match the implementation.
Define the size parameter as constant.
Fixes: 9a8bcabd8a ("axi: Add AXI sandbox driver and simple emulator")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
K3 devices have some firewalls set up by ROM that we usually remove so
that the development is easy in HS devices.
While removing the firewalls disabling a background region before
disabling the foreground regions keeps the firewall in a state where all
the transactions will be blacklisted until all the regions are disabled.
This causes a race for some other entity trying to access that memory
region before all the firewalls are disabled and causes an exception.
Since there is no guarantee on where the background regions lie based on
ROM configurations or no guarantee if the background regions will allow
all transactions across the memory spaces, iterate the loop twice removing
the foregrounds first and then backgrounds.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
This reverts commit b8ebf24e7f.
This patch seems to be fundamentally wrong and requires a different way
on how the background firewalls should be configured so revert the patch
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When build U-boot with clang with using commands:
$ make HOSTCC=clang xenguest_arm64_defconfig
$ make HOSTCC=clang CROSS_COMPILE=aarch64-linux-gnu- \
CC="clang -target aarch64-linux-gnueabi" -j8
The compiler reports error:
/tmp/start-acdf31.s:330:1: error: symbol '_start' is already defined
_start:
^
Because the symbol '_start' has been defined twice, one is defined in
arch/arm/cpu/armv8/start.S, another is defined in the header
boot0-linux-kernel-header.h.
To fix building failure, this patch removes the symbol '_start' from
boot0-linux-kernel-header.h.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
ARM requires a 4-byte alignment on all ARM code (though this
requirement is relaxed to 2-byte for some THUMB code) and we
should be explicit about that here.
GAS has its own fix for this[1] that forces proper alignment
on any section containing assembled instructions, but this is
not universal: Clang's and other gaslike assemblers lack this
implicit alignment. Whether or not this is considered a bug in
those assemblers, it is better to ask directly for what we want.
[1]: https://sourceware.org/bugzilla/show_bug.cgi?id=12931
Signed-off-by: Sam Edwards <CFSworks@gmail.com>
Powerpc configurations are apparently able to do unaligned accesses. But
in an attempt to clean up and handle unaligned accesses in the same way
we ignore that and use the common asm-generic/unaligned.h directly
instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
M68k essentially duplicates the content of asm-generic/unaligned.h, with
an exception for non-Coldfire configurations. Coldfire configurations
are apparently able to do unaligned accesses. But in an attempt to clean
up and handle unaligned accesses in the same way we ignore that and use
the common asm-generic/unaligned.h directly instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Acked-by: Angelo Dureghello <angelo@kernel-space.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Mips essentially duplicates the content of asm-generic/unaligned.h, so use
that file directly instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Sh essentially duplicates the content of asm-generic/unaligned.h, so use
that file directly instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Arm duplicates the content of asm-generic/unaligned.h, so use that file
directly instead.
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As part of various code clean-ups we have on occasion missed removing
unused header files. None of these files are referenced anywhere else
at this point.
Signed-off-by: Tom Rini <trini@konsulko.com>
It seems like the header inclusion guard for some Uniphier DDR PHY
header was misspelled.
Make the preprocessor symbol for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It seems like the header inclusion guards for some IMX related headers
were misspelled or got out of sync.
Make the preprocessor symbols for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This platform is currently unmaintained and untested, so remove it.
Further, as it is the only TI816X SoC example, remove related files as
well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Apple's M2 Pro/Max SoC are somewhat similar to the M1 Pro/Max but
need a tweaked memory map. USB, NVMe, UART and WDT are working
with the existing drivers.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
K3 GP devices allows booting the secure binaries on them by bypassing
the x509 header on them.
ATF and OPTEE firewalling required the rproc_load to be called before
authentication. This change caused the failure for GP devices that
strips off the headers. The boot vector had been set before the headers
were stripped off causing the runtime stripping to fail and stripping
becoming in-effective.
Separate out the secure binary check on GP/HS devices so that the
boot_vector could be stripped before calling rproc_load. This allows
keeping the authentication later when the cluster is on along with
allowing the stripping of the binaries in case of gp devices.
Fixes: 1e00e9be62 ("arm: mach-k3: common: re-locate authentication for atf/optee")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
When booting with HS silicon, the system firmware image is 278270, which
is slightly larger than currently allocated amount.
This can cause unexpected behavior if this overlap interferes with other
things in memory, so increase this with a slightly margin added as well
to avoid any boot issues that can appear after system firmware gets
loaded.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tero Kristo <kristo@kernel.org>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Reviewed-by: Dhruva Gole <d-gole@ti.com>
In non-combined boot flow for K3, all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721e was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
The commit changes R5 MCU scratchpad for j721e to an SRAM region.
Old Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c85b20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c85bfc
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf5bfc)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New Map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c40000 (approx)
│ EMPTY │
├─────────────────────────────────────┤ 0x41c81920
│ STACK │
│ SPL_SIZE_LIMIT_PROVIDE_STACK=0x4000 │
├─────────────────────────────────────┤ 0x41c85920
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c859f0
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x70000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41cf59f0)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ 0x41cff9fc
│ NEW MCU SCRATCHPAD │
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Fixes: ab977c8b91 ("configs: j721s2_evm_r5: Enable support for building multiple dtbs into FIT")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[n-francis@ti.com: SRAM allocation addressing diagram]
Signed-off-by: Neha Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
When building for secure devices using non-buildman based image generation
the signed tispl.bin file is called tispl.bin_HS. Also build the unsigned
tispl.bin file as expected.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
To avoid using static setting for ECC enabled DDR size, switch
to calculate DDR size from DDRC setting
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update the DDR init flow for multi-setpoint support on i.MX93. A new
fsp_cfg struct need to be added in the timing file to store the diff
part of the DDRC and DRAM MR register for each setpoint.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add 625M bypass clock that may be used DRAM 625M
bypass mode support.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to DDRPHY errata, the Rank-to-Rank Spacing and tphy_rdcsgap
specification does not include the Critical Delay Difference (CDD) to
properly define the required rank-to-rank read command spacing after
executing PHY training firmware.
Following the errata workaround, at the end of data training, we get
all CDD values through the MessageBlock, then re-configure the DDRC
timing of WWT/WRT/RRT/RWT with comparing MAX CDD values.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently bootaux only supports to boot M33 core from TCM. Since ATF
has changed to use x2 parameter for M33 image address, update the
bootaux command to use input address, so we can support boot from
any possilbe address like TCM, DDR, Flexspi NOR.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
According to datasheet, iMX93 has fused parts with CORE1 or NPU or
both disabled. So update code to support it, the kernel device tree
runtime update will be added in future patches.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Config the A55 alt root clock to 500MHz(LD mode frequency)
by default. Normally, this clock root is only used as an
intermediate clock soure for A55 core/dsu when change the
ARM PLL frequency.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The HW_CTRL_SEL should be cleared when configuring PLL to avoid
potential glitch
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Support print reset cause. Since SRSR is not accessible from non-secure
world, so first save it to grp0, then read it in non-secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The MAC addresses are hard coded for bring up. Change it to support
reading from fuse.
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
OPTEE memory region is set secure access only in ATF with configuration
to TRDC, and need to remove it from U-Boot, otherwise U-Boot and Kernel
may crash when accessing the memory
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
Commit 1a7904fdfa ("mmc: fsl_esdhc_imx: Use esdhc_soc_data
flags to set host caps") exposed the following SD card error:
U-Boot 2023.04-00652-g487e42f7bc5e (Apr 05 2023 - 22:14:21 -0300)
CPU: Freescale i.MX7D rev1.0 1000 MHz (running at 792 MHz)
CPU: Commercial temperature grade (0C to 95C) at 35C
Reset cause: POR
Model: Freescale i.MX7 SabreSD Board
Board: i.MX7D SABRESD in non-secure mode
DRAM: 1 GiB
Core: 100 devices, 19 uclasses, devicetree: separate
PMIC: PFUZE3000 DEV_ID=0x30 REV_ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... Card did not respond to voltage
select! : -110
*** Warning - No block device, using default environment
The reason of the problem, as explained by Ye Li:
"When UHS is enabled in defconfig, the usdhc1 node in imx7d-sdb.dts does
not configure pad for VSELECT, also the data pad should be set to
100Mhz/200Mhz pin states."
Apply these changes into u-boot.dtsi for now. When these changes
reach the Linux mainline imx7d-sdb, they can be dropped from u-boot.dtsi.
This fixes UHS mode on the imx7d-sdb board.
Suggested-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Stop polluting the architecture directory with driver specific code,
move it into driver where it should be. Split the code slightly so
the MX8MM/MX8MN fuse readout and programming and MX8MP fuse readout
and programming are in their separate functions, and called in case
of matching SoC.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
It seems like the ROM log events for the iMX8M are not fully covered by
AN12853 i.MX ROMs Log Events, Rev. 0, May 2020. On iMX8M the ROM event
ID 0x82 seems to use parameter0 which stops the parsing because the end
of list is detected too early.
This patch adds ROM event ID 0x82 and skips the next word if ID 0x82 is
parsed.
Fixes: a5ee05cf71 ("ARM: imx: Pick correct eMMC boot partition from ROM log")
Signed-off-by: Fedor Ross <fedor.ross@ifm.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 5 Model B.
Similar to RK3568 the BootRom in RK3588 can read all data and look for
idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1492992 bytes read in 129 ms (11 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x16c800
1300480 bytes written, 192512 bytes skipped in 11.103s, speed 137694 B/s
The BROM_BOOTSOURCE_ID value read back when booting from SPI flash does
not match the expected value of 3 (SPINOR) used by other SoCs. Instead a
value of 6 is read back, add a new enum value to handle this new
bootsource id.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Eugen Hristev <eugen.hristev@collabora.com>
Enable pinctrl for sdhci in SPL to support loading of FIT image from SD
and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Like other Rockchip SoCs, DM_RESET and DM_REGULATOR_FIXED is useful
across RK3588 platform. Select them from arch Kconfig.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add sfc and flash node to device tree and config options to enable
support for booting from SPI NOR flash on Radxa ROCK 3 Model A.
Unlike prior generation SoCs the BootRom in RK3568 can read all data and
look for idbloader at 0x8000, same as on SD and eMMC.
Use the rksd format and modify the mkimage offset to generate a bootable
u-boot-rockchip-spi.bin that can be written to 0x0 of SPI NOR flash. The
FIT image is loaded from 0x60000.
=> sf probe
SF: Detected mx25u12835f with page size 256 Bytes, erase size 4 KiB, total 16 MiB
=> load mmc 1:1 10000000 u-boot-rockchip-spi.bin
1384448 bytes read in 119 ms (11.1 MiB/s)
=> sf update $fileaddr 0 $filesize
device 0 offset 0x0, size 0x152000
1179648 bytes written, 204800 bytes skipped in 9.901s, speed 143185 B/s
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable pinctrl for sdmmc and sdhci in SPL to support loading of FIT
image from SD and eMMC storage when booting from SPI NOR flash.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update defconfig for rk3566-radxa-cm3-io with new defaults. Also add
missing supported mmc modes to sdhci node.
Remove the SPL_ROCKCHIP_BACK_TO_BROM=y option, SPL is expected to load
next stage from a FIT image and then jump to next stage not back to
BootRom.
Add CONFIG_SPL_FIT_SIGNATURE=y to let SPL verify an auto generated hash
of FIT images. This help indicate if there is an issue loading any of
the images to DRAM or SRAM.
Extend SPL_MAX_SIZE to 0x40000, SPL is loaded to 0x0 and TF-A is loaded
to 0x40000, use the space in between as SPL_MAX_SIZE.
Add config option to include useful gpio cmd.
Remove the CONFIG_NET_RANDOM_ETHADDR=y option, ethaddr and eth1addr is
set based on cpuid read from OTP.
Filter out assigned-clock props with CONFIG_OF_SPL_REMOVE_PROPS,
U-Boot proper will read and configure assigned-clock props.
Add CONFIG_SYS_NS16550_MEM32=y to use 32bit access of serial register.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to xin24m clock node, it is referenced by cru node.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the PCIe 2x1l 2 device and associated combphy.
On this bus, the Rock5B has an Ethernet transceiver connected.
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
[eugen.hristev@collabora.com: minor tweaks]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: add PCIe pins]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the node for PCIe 2x1l 2 device together with the corresponding
combphy.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: moved to -u-boot.dtsi, minor
adaptations]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
[jonas@kwiboo.se: adapt to kernel node]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on ROCK Pi 4.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the use of SDMA mode to boost eMMC performance on RockPro64.
Also add missing flags to indicate the supported MMC modes.
Using mmc read command to read 32 MiB data shows following improvement:
=> time mmc read 10000000 2000 10000
Before: time: 3.178 seconds
After: time: 0.402 seconds
This also enables CONFIG_SPL_FIT_SIGNATURE option to help discover
any possible future issue with loading TF-A into DRAM/SRAM.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Loading part of TF-A into SRAM from eMMC using DMA fails on RK3399
similar to other Rockchip SoCs. Checksum validation fails with:
## Checking hash(es) for Image atf-2 ... sha256 error!
Bad hash value for 'hash' hash node in 'atf-2' image node
spl_load_simple_fit: can't load image loadables index 1 (ret = -1)
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
### ERROR ### Please RESET the board ###
Add a device tree property, u-boot,spl-fifo-mode, to control when the
rockchip_sdhci driver should disable the use of DMA and fallback on PIO
mode. Same device tree property is used by the rockchip_dw_mmc driver.
In commit 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks
read in a single command") the DMA mode was disabled using a CONFIG
option on RK3588. Revert that and instead disable DMA using the device
tree property for all RK3588 boards, also apply similar workaround for
all RK3399 boards.
Fixes: 2cc6cde647 ("mmc: rockchip_sdhci: Limit number of blocks read in a single command")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: Quentin Schulz <foss+uboot@0leil.net> # RK3399 Puma, RK3588 Tiger
The current DT bindings for the rk3588 clock use a different ID than the
one that is supposed to be written to the hardware registers.
Thus, we cannot use directly the id provided in the phandle, but rather
use a lookup table to correctly setup the hardware.
This approach has been implemented already in Linux, by commit :
f1c506d152ff ("clk: rockchip: add clock controller for the RK3588")
Hence, implement a similar approach using the lookup table, and adapt
the existing reset driver to work with SoCs using lookup table.
The file rst-rk3588.c has been copied as much as possible from Linux.
Adapt the clk rk3588 driver as well to bind the reset driver with the
lookup table.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
To be able to initialize the pinctrl correctly at SPL level and read
u-boot proper from SD-Card, the pinctrl must be initialized.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add USB 2.0 host nodes and PHYs.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Co-developed-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
- Merge in a long-standing fix for some exynos platforms, correct a
Kconfig description, fix some env issues, fix an issue in
devfdt_get_addr_size_index_ptr and look for "panel-timings" not
"panel-timing" per upstream binding.
In case where a single timing resolution is implemented in the
device-tree, the property is named "panel-timing", as specify
in Linux kernel binding file:
Documentation/devicetree/bindings/display/panel/panel-common.yaml
# Display Timings
panel-timing:
description:
Most display panels are restricted to a single resolution and
require specific display timings. The panel-timing subnode expresses those
timings.
$ref: panel-timing.yaml#
display-timings:
description:
Some display panels support several resolutions with different timings.
The display-timings bindings supports specifying several timings and
optionally specifying which is the native mode.
$ref: display-timings.yaml#
Fixes: 0347cc7732 ("drivers: core: ofnode: Add panel timing decode.")
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
In current implementation, applications can execute only on R5 core 0.
The boot address for R5 core 1 is not supplied. Pass TCM address for
R5 core 1 based on the argument to fix the issue.
Remove incomplete comment.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/da865717d26648ab7a84345ca8749712efdddee5.1680699999.git.michal.simek@amd.com
The "zynqmp tcminit split" command should halt both cores and not just RPU1
when configuring the TCM memory for split mode.
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/20230323082506.31576-1-neal.frager@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
We use the terms 'distro' to mean extlinux but they are not really the
same. 'Distro' could refer to any method of booting a distribution,
whereas extlinux is a particular method.
Also we sometimes use syslinux, but it is better to use the same term in
all cases.
Rename distro to syslinux and also update bootstd uses of syslinux to use
extlinux instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
The RZ/N1 is a family of SoC devices from Renesas, featuring:
* ARM Cortex-A7 CPU (single/dual core) and/or Cortex-M3
* Integrated SRAM up to 6MB
* Integrated gigabit ethernet switch
* Optional DDR2/3 controller
* I2C, SPI, UART, NAND, QSPI, SDIO, USB, CAN, RTC, LCD
Add basic support for this family, modeled on the existing RZA1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This is taken directly from Linux kernel 6.3
(commit 457391b0380335d5e9a5babdec90ac53928b23b4)
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Commit 2564fce7ee ("sunxi: move Cortex SMPEN setting into start.S")
added SPL_ARMV7_SET_CORTEX_SMPEN to enable setting SMP bit. For
platforms not using SPL boot, add the corresponding non-SPL config,
so that CONFIG_IS_ENABLED(ARMV7_SET_CORTEX_SMPEN) works as expected.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
These are not used in TPL so disable the drivers to save space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This copies the cpu_call64() function to memory address and then jumps to
it. This seems to work correctly even when called from SPL, which is
running from SPI flash.
Drop the copy as it is not needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't need to commit the SPI-flash MTRR change immediately, since it is
now done in the board_init_f_r(). Also this causes chromebook_link64 to
hang, presumably since we are still running from CAR (Cache-as-RAM) in
SPL. Coral handles this OK, perhaps since it is running from a different
memory area, but it has no effect on Coral anyway.
Drop the extra mtrr_commit() in the SPL implementation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function is used by U-Boot proper. It does not set up MTRRs when SPL
is enabled, but we do want this done when it is called from SPL. In fact
it is confusing to use the same function from SPL, since there are quite
a few conditions there.
All init_cache_f_r() really does is commit the MTRRs and set up the cache.
Do this in the SPL's version of this function instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use the binman symbols for this, to avoid hard-coding the value. We could
use CONFIG_X86_OFFSET_U_BOOT for the address, but it seems better to
obtain the offset and size through the same mechanism.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Show the area of memory cleared for BSS, when debugging is enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
SPL printf() does not normally support %#x so just use %x instead. Hex is
expected in U-Boot anyway.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For now, just enable the fast-but-large string functions in 32-boot
U-Boot proper only. Avoid using them in SPL. We cannot use then in 64-bit
builds since we only have 32-bit assembly.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The debug UART is already set up in SPL, so there is no need to do
anything here. We must provide the (empty) function though.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The bd82x6x_get_gpio_base() does not work if the LPC is not set up.
Probe it early to avoid this problem.
In chromebook_link64 this problem shows up as an inability to read
the GPIO straps for the memory type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The original function was only called once, before relocation. The new
one is called again after relocation. This was not the intent of the
original call. Fix this by renaming and updating the calling logic.
With this, chromebook_link64 makes it through SPL.
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Sometimes coreboot adds new tags that U-Boot does not know about. These
are silently ignored, but it is useful to at least know what we are
missing.
Add a way to collect this information. For Brya it shows:
Unimpl. 38 41 37 34 42 40
These are:
LB_TAG_PLATFORM_BLOB_VERSION
LB_TAG_ACPI_CNVS
LB_TAG_FMAP
LB_TAG_VBOOT_WORKBUF
LB_TAG_TYPE_C_INFO
LB_TAG_BOARD_CONFIG
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present any ACPI tables created by prior-stage firmware are ignored.
It is useful to be able to view these in U-Boot.
Pick this up from the sysinfo tables and display it with the cbsysinfo
command. This allows the 'acpi list' command to work when booting from
coreboot.
Adjust the global_data condition so that acpi_start is available even if
table-generation is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
We have several Kconfig options for ACPI, but all relate to specific
functions, such as generating tables and AML code.
Add a new option which controls including basic ACPI library code,
including the lib/acpi directory. This will allow us to add functions
which are available even if table generation is not supported.
Adjust the command to avoid a build error when ACPIGEN is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Avoid searching starting at 0 since this memory may not be available,
e.g. if protection against NULL-pointer access is enabled. The table
cannot be there anyway, since the first 1KB of memory was originally
used for the interrupt table and coreboot avoids it.
Start at 0x400 instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This avoid an error with enable_sata_clock when
defined(CONFIG_SATA) is changed to CONFIG_IS_ENABLED(SATA).
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_IS_ENABLED(SPL_X86_32BIT_INIT)
would check for CONFIG_SPL_SPL_X86_32BIT_INIT for SPL builds
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Rockchip NFC driver update and dev addr pointer api update;
- use standard dr_mode for usb driver;
- rock pi boards dts update;
- Add rk3566 Anbernic boards;
- Misc fixes for drivers;
The OTG port is identified by inspecting the "dr_mode" property which is
expected to be "otg" for this port. But it will work just as well as a
device controller when dr_mode is set to "peripheral", which may be
required if the mode detection pin is not set up correctly and the
device controller needs to be programmed to override this.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Instead of duplicating the string values here, use usb_get_dr_mode() to
handle the property lookup and converting the values to an enum.
This is implemented with a switch in preparation for the next patch
which adds extra handling for peripheral mode.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Linux commit 246450344dad arm64: dts: rockchip: rk3399: Radxa ROCK 4C+
Add support for Radxa ROCK 4C+ SBC.
Key differences of 4C+ compared to previous ROCK Pi 4.
- Rockchip RK3399-T SoC
- DP from 4C replaced with micro HDMI 2K@60fps
- 4-lane MIPI DSI with 1920*1080
- RK817 Audio codec
Also, an official naming convention from Radxa mention to remove
Pi from board name, so this 4C+ is named as Radxa ROCK 4C+ not
Radxa ROCK Pi 4C+.
Signed-off-by: Stephen Chen <stephen@radxa.com>
Signed-off-by: Manoj Sai <abbaraju.manojsai@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
sync dts{,i} files for Radxa ROCK Pi 4 series with Linux 6.3.
because rk3399-rock-pi-4a.dts is enough for ROCK Pi 4A/B/A+/B+ and ROCK
4SE, delete dts{,i} for ROCK Pi 4B.
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Anbernic RGxx3 is a "pseudo-device" that encompasses the following
devices:
- Anbernic RG353M
- Anbernic RG353P
- Anbernic RG353V
- Anbernic RG353VS
- Anbernic RG503
The rk3566-anbernic-rgxx3.dtsi is synced with upstream Linux, but
rk3566-anbernic-rgxx3.dts is a U-Boot specific devicetree that
is used for all RGxx3 devices.
Via the board.c file, the bootloader automatically sets the correct
fdtfile, board, and board_name environment variables so that the
correct devicetree can be passed to Linux. It is also possible to
simply hard-code a single devicetree in the boot.scr file and use
that to load Linux as well.
The common specifications for each device are:
- Rockchip RK3566 SoC
- 2 external SDMMC slots
- 1 USB-C host port, 1 USB-C peripheral port
- 1 mini-HDMI output
- MIPI-DSI based display panel
- ADC controlled joysticks with a GPIO mux
- GPIO buttons
- A PWM controlled vibrator
- An ADC controlled button
All of the common features are defined in the devicetree synced from
upstream Linux.
TODO: DSI panel auto-detection for the RG353 devices (requires porting
of DSI controller driver and DSI-DPHY driver to send DSI commands to
the panel).
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so fix ofnode_get_addr_size function with fdt_addr_t input to
be able to handle both sizes for stm32mp SoC in spl.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so fix some
debug strings with fdt_addr_t to be able to handle both sizes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The Rockchip SoC rk3288 has 2 types of device trees floating around.
A 64bit reg size when synced from Linux and a 32bit for U-boot.
A pre-probe function in the syscon class driver assumes only 32bit.
For other odd reg structures the regmap must be defined in the individual
syscon driver. Store rk3288 platdata in a regmap before pre-probe
during bind.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
In order to use QMC mode in the CPM, a SCC requires more space
in parameter RAM.
After SCC1 there is I2C parameter RAM and after SCC2 there is
SPI parameter RAM. MPC866 and MPC885 can already relocate I2C and.
SPI parameter RAM.
But in order to free space after SCC3 and SCC4, SMC1 and SMC2
need to be relocated. In order to do so, a CPM microcode patch
is required.
Binary data for that patch is copied from Linux kernel.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
MPC885 CPU has the following ERRATA:
When the USB controller is configured in Host mode, and the
SOF generation (SFTE=1 in USMOD register) is being used,
there may be false CRC error indication in other SCCs.
Although the data is received correctly, the CRC result
will be corrupted.
Add capability to load the related microcode to fix it.
The microcode binary data is copied from Linux kernel.
Other microcode will be added in following patch so make it
a Kconfig choice.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
sparse reports the following warning:
CHECK arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c
arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c:29:9: warning: cast removes address space '<asn:2>' of expression
arch/powerpc/cpu/mpc8xx/micropatch_usb_sof.c:30:9: warning: cast removes address space '<asn:2>' of expression
This is because of (void *) casts for using memcpy() as a substitute.
Do like other architectures, __force the cast to silence the warning
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Somehow, I managed to typo our company name in the U-Boot
and Linux kernel submissions.
Fix this and update the copyright year at the same time.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This synchronises the Linux device tree with U-Boot
(cp linux/..../fsl-ls1088a-ten64.dts uboot/..../fsl-ls1088a-ten64.dts),
as of Linux v6.2-rc5.
Missing from the U-Boot copy previously was the
Ethernet PCS definitions (required for linking with PHY in
Linux but not used by U-Boot) and various upstream
fixes and formatting changes.
The board microcontroller (which doesn't have a Linux driver)
has been moved to the -u-boot.dtsi, as well as the
spi0 quadspi alias (used by U-boot 'sf' but not valid for Linux).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Our [U-Boot] copy of fsl-ls1088a.dtsi had all the hardware under
the top level, until the DM_SERIAL implementation recently.
In this commit, remove any remaining devices (that were in U-Boot,
but not touched by previous patches in this series) to be under /soc,
updating to their upstream (Linux) bindings.
The bindings have been copied closest to their relative positions
in the Linux version, so the eventual result is that the U-Boot
and Linux fsl-ls1088a.dtsi will be identical.
The next commit will add the hardware bindings that were not
in U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the fsl-mc device tree definition under the /soc
node, as well as adding interrupt and IOMMU definitions that
were not in U-Boot before.
There are slight differences between the two bindings
as we add a "simple-mfd" compatible to function
under U-Boot's driver model.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Synchronise the MDIO controller definitions with Linux, so
the controllers will be usable when passing U-Boot's
control FDT to Linux.
This also adds the PCS (internal controller) definitions
which are not used by U-Boot.
Caveat: The kernel definition uses "fsl,fman-memac-mdio",
as with other members of the Layerscape family, but
U-Boot uses a different driver for the DPAA2
Family devices (LS1088/LS2088/LX2160). So
we use "fsl,ls-mdio" as the first compatible string
for these devices.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Synchronise the USB device tree definition with Linux, allowing
the U-Boot control FDT to be used to boot a Linux system with
working USB.
An extra compatible string, "fsl,layerscape-dwc3" is needed
for special handling in U-Boot, so has been added to the
-u-boot.dtsi file. It might be better to add this to the
Linux source bindings.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
U-Boot's definition for the I2C controllers did not contain any
clock information. This resulted in the I2C not functioning when
the U-Boot control FDT was passed to Linux.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Move the GPIO controller definitions under the "soc" and in
the same relative position as the Linux kernel fsl-ls1088a.dtsi.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This is required for Linux to boot using the same FDT as
U-Boot (such as passing the control FDT to bootefi).
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
The Linux kernel fsl-ls1088a.dtsi disables (status="disabled")
all PCIe controllers by default, with the bootloader (i.e U-Boot)
enabling the appropriate controllers (specified by the board
reset control word/RCW) by FDT fixup.
However, U-Boot needs these controllers to be enabled
to be usable, which we can add in the u-boot only dtsi.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the PCIe controller definitions under /soc and adopts
the same bindings (fsl,ls1088a-pcie) as Linux. Previously,
the format was different between the two versions.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
To synchronise the device tree in U-Boot with Linux, the GIC
(Interrupt Controller) and SMMU/IOMMU nodes need to be synchronised
before changing any dependent components like PCIe and DPAA2/fsl-mc.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
The top-level "memory" node does not exist in the Linux
version of the fsl-ls1088a.dtsi file. Move it to the U-Boot
"tweak" file, so we can have an identical copy of
fsl-ls1088a.dtsi between the projects in the end.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This moves the bootph-all tags that were added in commit a593c1fec5
("arch: arm: dts: fsl-ls1088a.dtsi: tag serial nodes with bootph-all")
into a u-boot only include.
Due to the way the U-Boot device tree "tweak" system is setup[1],
we need to have a per-board <boardname>-u-boot.dtsi, which will
include the "fsl-ls1088a-u-boot.dtsi" tweaks.
By doing so, future updates to fsl-ls1088a.dtsi from upstream
(Linux kernel) can just be copied directly into the U-Boot tree,
without worrying about any extra data local to U-Boot.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
[1] - https://u-boot.readthedocs.io/en/latest/develop/devicetree/control.html#adding-tweaks-for-u-boot
The CONFIG_SYS_SOC, CONFIG_SYS_CPU and CONFIG_SYS_VENDOR
values are the same for the entire Layerscape family,
meaning there is no ability to create a LS1088A only
file here. But we will be adding per-board tweaks
later in any case.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
This a problem I found while updating the U-Boot fsl-ls1088a.dtsi
to match the Linux version.
fdt_fixup_remove_jr did not check whether there was a "crypto"
alias in the device tree before calling more fdt_* functions,
which resulted in a crash.
Fixes: a797f274
("ARMv8/sec_firmware : Update chosen/kaslr-seed with random number")
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
Update the DDR settings to those generated using 0.6 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Update the DDR settings to those generated using 0.9.1 version of
Jacinto 7 DDRSS Register Configuration tool.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
On K3 HS-SE devices all the firewalls are locked by default
until sysfw comes up. Rom configures some of the firewall for its usage
along with the SRAM for R5 but the PSRAM region is still locked.
The K3 MCU Scratchpad for j721s2 was set to a PSRAM region triggering the
firewall exception before sysfw came up. The exception started happening
after adding multi dtb support that accesses the scratchpad for reading
EEPROM contents.
Old map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c61f20 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c65f20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c66000
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x10000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41c76000)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ (0x41c80000)
│ DM DATA │
├─────────────────────────────────────┤ (0x41c84130) (approx)
│ EMPTY │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
New map:
┌─────────────────────────────────────┐ 0x41c00000
│ SPL │
├─────────────────────────────────────┤ 0x41c61f20 (approx)
│ STACK │
├─────────────────────────────────────┤ 0x41c65f20
│ Global data │
│ sizeof(struct global_data) = 0xd8 │
├─────────────────────────────────────┤ gd->malloc_base = 0x41c66000
│ HEAP │
│ CONFIG_SYS_MALLOC_F_LEN = 0x10000 │
├─────────────────────────────────────┤ CONFIG_SPL_BSS_START_ADDR
│ SPL BSS │ (0x41c76000)
│ CONFIG_SPL_BSS_MAX_SIZE = 0xA000 │
├─────────────────────────────────────┤ (0x41c80000)
│ DM DATA │
├─────────────────────────────────────┤ (0x41c84130) (approx)
│ EMPTY │
├─────────────────────────────────────┤ SYS_K3_MCU_SCRATCHPAD_BASE
│ SCRATCHPAD │ (0x41cff9fc)
│ SYS_K3_MCU_SCRATCHPAD_SIZE = 0x200 │
└─────────────────────────────────────┘ CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX
(0x41cffbfc)
Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Create *-u-boot.dtsi files for each target dtb of the IOT2050 series so
that we can drop the #include deviations from upstream dts[i] files
here.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Using SMC relocation microcode patch or USB-SOF microcode patch
will disable DPRAM memory from 0x2000 to 0x2400 and from 0x2f00
to 0x3000.
At the time being, init RAM is setup to use 0x2800-0x2e00, but
the stack pointer goes beyond 0x2800 and even beyond 0x2400.
For the time being we are not going to use any microcode patch
that uses memory about 0x3000, so reorganise setup to use:
- 0x2800 - 0x2e00 for init malloc and global data and CPM buffers
- 0x3000 - 0x3c00 for init stack
For more details about CPM dual port ram, see
commit b1d62424cb ("powerpc: mpc8xx: redistribute data in CPM dpram")
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
With relocation, CPM parameter RAM can be anywhere in the
dual port RAM, so don't split dual port RAM.
Remove dparam and dparam16 members of struct comm_proc
PROFF_XXX become offsets from the start of dual port RAM,
then they are now consistant with the offsets in RPBASE
registers.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This platform is unsupported by TI and was never widely distributed. As
this is untested for a long while and missing some DM conversions,
remove it and related device tree files.
Signed-off-by: Tom Rini <trini@konsulko.com>
Errata doc: https://www.ti.com/lit/pdf/sprz457
Errata ID i2331 CPSW: Device lockup when reading CPSW registers
Details: A device lockup can occur during the second read of any CPSW
subsystem register after any MAIN domain power on reset (POR). A MAIN
domain POR occurs using the hardware MCU_PORz signal, or via software
using CTRLMMR_RST_CTRL.SW_MAIN_POR or CTRLMMR_MCU_RST_CTRL.SW_MAIN_POR.
After these resets, the processor and internal bus structures may get
into a state which is only recoverable with full device reset using
MCU_PORz.
Due to this errata, Ethernet boot should not be used on this device.
Workaround(s): To avoid the lockup, a warm reset should be issued after
a MAIN domain POR and before any access to the CPSW registers. The warm
reset realigns internal clocks and prevents the lockup from happening.
Workaround above errata by calling do_reset() in case of cold boot in
order to trigger warm reset. This needs enabling SYSRESET driver in R5
SPL to enable TI SCI reset driver.
Signed-off-by: Nitin Yadav <n-yadav@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
Add board specific devicetree for Bananapi R3 SBC.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Enable Quality of Service (QoS) blocks for Display SubSystem (DSS), by
servicing the DSS - DDR traffic from the Real-Time (RT) queue. This is
done by setting the DSS DMA orderID to 8.
The C7x and VPAC have been overwhelming the DSS's access to the DDR
(when it was accessing via the Non Real-Time (NRT) Queue), primarily
because their functional frequencies, and hence DDR accesses, were
significantly higher than that of DSS. This led the display to flicker
when certain edgeAI models were being run.
With the DSS traffic serviced from the RT queue, the flickering issue
has been found to be mitigated.
The am62a qos files are auto generated from the k3 resource partitioning
tool.
Section-3.1.12, "QoS Programming Guide", in the AM62A TRM[1], provides
more information about the QoS, and section-14.1, "System Interconnect
Registers", provides the register descriptions.
[1] AM62A Tech Ref Manual: https://www.ti.com/lit/pdf/spruj16
Signed-off-by: Aradhya Bhatia <a-bhatia1@ti.com>
J721E and J7200 have same file j721e_init.c which had the firewall
configs for J721E being applied on J7200 causing the warnings. Split the
firewalls for both the boards to remove those warnings.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
