The serial number is located at offset 0x14 of the EEPROM
under i2c0 bus at address 0x54.
To print the serial number in Linux:
SERNUM=$(cat /proc/device-tree/serial-number)
echo $SERNUM
Signed-off-by: Fabio Estevam <festevam@denx.de>
Currently, the DDR type is retrieved by iteracting inside an array
of possible DDR types.
This may take saveral attempts, which slows the overall U-Boot process
and does not provide a good user experience:
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 1/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0x5000010 ]
resetting ...
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 2/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0x1061010 ]
resetting ...
U-Boot SPL 2021.07 (Feb 28 2022 - 06:39:32 +0000)
DDRINFO: Cfg attempt: [ 3/6 ]
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(T): mr5-8 [ 0xff000010 ]
Normal Boot
WDT: Not starting
Trying to boot from MMC2
NOTICE: BL31: v2.5(release):v2.5
NOTICE: BL31: Built : 07:12:44, Jan 24 2022
Improve the boot time by retrieving the correct DDR information from
the EEPROM:
U-Boot SPL 2022.04-rc4-00045-g6d02bc40d58c (Mar 19 2022 - 08:22:29 -0300)
DDRINFO(D): Kingston 4096G
DDRINFO(M): mr5-8 [ 0xff000010 ]
DDRINFO(E): mr5-8 [ 0xff000010 ]
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from MMC2
NOTICE: BL31: v2.5(release):v2.5
NOTICE: BL31: Built : 22:28:11, Mar 15 2022
Based on the original code from Compulab's U-Boot.
Tested on a imx8mm-cl-iot-gate board populated with 4GB of RAM.
Signed-off-by: Fabio Estevam <festevam@denx.de>
imx8mm-cl-iot-gate supports multiple DDR sizes and models.
The DDR type can be retrieved from the EEPROM, so add SPL code
that can be used to get the DDR information.
Based on the original code from Compulab's U-Boot.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The power/bd71837.h should no longer be included, since V1.1 SoM
uses only the PCA9450 PMIC and the BD71837 support was removed.
Drop the header too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now that it is possible to use regulator-fixed-clock make use
of it. This makes U-Boot detect the PHY on first cold-boot.
This commit also adjusts the code in setup_fec and follows
how it is done in mx6ullevk.c
This commit also slows down the boot-process by about 150ms
as it now waits for the regulator-fixed-clock voltage that
drives the PHY to go up.
If you rely on very fast boot-speeds and don't need ethernet
for your boot-process you can safely revert the changes on
imx6ull-colibri.dtsi
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Toradex uses the variable variant to distinguish between modules with
eMMC, NAND with wifi and NAND without wifi.
This variable is set on every boot. Set this variable also if we have a
NAND module without wifi to prevent issues.
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken fdt_module to flash.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
U-Boot should never save the environment unasked.
This also avoids storing broken ftd_file to eMMC.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Rename board_early_init_f() to board_early_init(), since this function
has nothing to do with actual board_early_init_f() as used throughout
U-Boot. The board_early_init() is function local to this board used to
configure UART and WDT pinmux. Wrap init_uart_clk() into this function
so that early UART init would be all in one place. Turn the function
into __weak one, so it could be overridden in case custom carrier board
uses different UART or needs custom IOMUX settings.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
If M33 handshake is successful, TPM and DSI panel MUX setting is
done by M33, no need to set them.
If handshake is failed or M33 is not booted, continue the TPM
and DSI panel MUX setting
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Update DDR PHY settings to support LPDDR4 mode only by adjusting
DQ VREF ctrl, ODT and pads drive strength.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Found the lposc fuse loading having impact to cpu idle in kernel.
Without the loading in dual boot mode, kernel will hang after idle
for a while.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.
Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This workaround is not needed on i.MX8ULP proto-1B EVK as board has
fixed the problem. Because we don't support proto-1A any longer,
remove the PMIC settings.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Conversion to DM_SERIAL is mandatory.
Select DM_SERIAL and add a imx6q-tbs2910-u-boot.dtsi file
that describes the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-by: Soeren Moch <smoch@web.de>
With DM_SERIAL selected, it is no longer needed board code to
initialize the UART.
Describe the nodes that require dm-pre-reloc, which allows
the DM model to configure the UART pinctrl early.
Remove the now unneeded board UART initialization.
Signed-off-by: Fabio Estevam <festevam@denx.de>
DM is not used for the SPL and a generic DT is used in the SPL
which requires no fixups. Remove the call in the SPL and move the function
into the U-Boot code.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Since DM_SERIAL is used for U-Boot we no longer need legacy UART code in
common.c shared by the SPL and U-Boot. Move the legacy UART config to
the non-DM SPL.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
convert to DM_I2C for U-Boot while leaving SPL legacy I2C:
- Move I2C config from common to SPL
- Move PMIC config from common to SPL (no need to re-configure pmic)
- add DM_I2C support to eeprom/gsc functions shared by SPL and U-Boot
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The Ethernet controller and PHY use the device tree info to
configure themselves, so it's not necessary to manually do it
in the board file. This permits the removal of a bunch of headers
as well.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
With the correct settings described in the device-tree the PHY settings
in the board init are no longer required. The values are taken from the
linux device tree.
The PHY latency settings are derived from the phy-mode property and the
voltage seetings are done via the regulator.
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
Tested-by: Marek Vasut <marex@denx.de> # 8MNANOD4-EVK
Reviewed-by: Fabio Estevam <festevam@gmail.com>
LS(1021/1012/1028/1043/1046/1088/2088), LX2160, LX2162
platforms are enabled with JR driver model.
removed sec_init() call from board files.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: Michael Walle <michael@walle.cc>
i.MX8(QM/QXP) - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
i.MX8MM/MN/MP/MQ - added support for JR driver model.
sec is initialized based on job ring information processed
from device tree.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Currently we require PHY interface mode to be known when
finding/creating the PHY - the functions
* phy_connect_phy_id()
* phy_device_create()
* create_phy_by_mask()
* search_for_existing_phy()
* get_phy_device_by_mask()
* phy_find_by_mask()
all require the interface parameter, but the only thing done with it is
that it is assigned to phydev->interface.
This makes it impossible to find a PHY device without overwriting the
set mode.
Since the interface mode is not used during .probe() and should be used
at first in .config(), drop the interface parameter from these
functions. Make the default value of phydev->interface (in
phy_device_create()) to be PHY_INTERFACE_MODE_NA. Move the interface
parameter to phy_connect_dev(), where it should be.
Change all occurrences treewide. In occurrences where we don't call
phy_connect_dev() for some reason (they only configure the PHY without
connecting it to an ethernet controller), set
phydev->interface = value from phy_find_by_mask call.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Rename constant PHY_INTERFACE_MODE_NONE to PHY_INTERFACE_MODE_NA to make
it compatible with Linux' naming.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Add helpers ofnode_read_phy_mode() and dev_read_phy_mode() to parse the
"phy-mode" / "phy-connection-type" property. Add corresponding UT test.
Use them treewide.
This allows us to inline the phy_get_interface_by_name() into
ofnode_read_phy_mode(), since the former is not used anymore.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Tested-by: Patrice Chotard <patrice.chotard@foss.st.com>
We use 'DEBUG' and not 'CONFIG_DEBUG' tree-wide for debug code that is
left in, and not wrapped by some other regular debugging type print
macro.
Cc: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
These values are only used in one file, reference them more directly.
Cc: Kamil Lulko <kamil.lulko@gmail.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This code is only used on the corvus platform, so migrate the LED on/off
code to this platform and remove it from the CONFIG namespace. In
theory, this should likely be moved to the modern GPIO LED driver as a
further cleanup.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_CM_INIT
CONFIG_CM_REMAP
CONFIG_CM_SPD_DETECT
CONFIG_CM_MULTIPLE_SSRAM
CONFIG_CM_TCRAM
We make the first three of these options be always enabled, as that
matches usage. We select the last two based on how they were defined in
armcoremodule.h. This also allows us to remove some unused code in
board/armltd/integrator/lowlevel_init.S
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Let CONFIG_TARGET_QEMU_VIRT imply CONFIG_CMD_SBI.
The sbi command provides detailed information about the SBI.
It is useful to test the discovery of extensions.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYkxUZwAKCRDKSWXLKUoM
IXJ2AKCQcoFK7wanCCvZfuEJCSwO5E4eCACginE2CFVXKcY1P8ta4ESusjY2TH0=
=HOoS
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2022.07-rc1 v2
xilinx:
- Allow booting bigger kernels till 100MB
zynqmp:
- DT updates (reset IDs)
- Remove unneeded low level uart initialization from psu_init*
- Enable PWM features
- Add support for 1EG device
serial_zynq:
- Change fifo behavior in DEBUG mode
zynq_sdhci:
- Fix BASECLK setting calculation
clk_zynqmp:
- Add support for showing video clock
gpio:
- Update slg driver to handle DT flags
net:
- Update ethernet_id code to support also DM_ETH_PHY
- Add support for DM_ETH_PHY in gem driver
- Enable dynamic mode for SGMII config in gem driver
pwm:
- Add driver for cadence PWM
versal:
- Add support for reserved memory
firmware:
- Handle PD enabling for SPL
- Add support for IOUSLCR SGMII configurations
include:
- Sync phy.h with Linux
- Update xilinx power domain dt binding headers
A big part is the DM pinctrl driver, which allows us to get rid of quite
some custom pinmux code and make the whole port much more robust. Many
thanks to Samuel for that nice contribution! There are some more or less
cosmetic warnings about missing clocks right now, I will send the trivial
fixes for that later.
Another big chunk is the mkimage upgrade, which adds RISC-V and TOC0
(secure images) support. Both features are unused at the moment, but I
have an always-secure board that will use that once the DT lands in the
kernel.
On top of those big things we have some smaller fixes, improving the
I2C DM support, fixing some H6/H616 early clock setup and improving the
eMMC boot partition support.
The gitlab CI completed successfully, including the build test for all
161 sunxi boards. I also boot tested on a A64, A20, H3, H6, and F1C100
board. USB, SD card, eMMC, and Ethernet all work there (where applicable).
Call into k3-ddrss driver to fixup device tree and resize the available
amount of DDR if ECC is enabled.
A second fixup is required from A53 SPL to take the fixup as done from
R5 SPL and apply it to DT passed to A53 U-boot, which in turn passes
this to the OS.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Use the appropriate fdtdec_setup_mem_size_base and
fdtdec_setup_bank_size calls in dram_init and dram_bank_init to pull
these values from DT, where they are already available, instead of
hardcoding them.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Now that mkimage can generate TOC0 images, and the SPL can interpret
them, hook up the build infrastructure so the user can choose which
image type to build. Since the absolute load address is stored in the
TOC0 header, that information must be passed to mkimage.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
These options are not currently enabled anywhere. Any new users should
use DM clocks and pinctrl.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This is now handled automatically by the pinctrl driver.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
/LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
yoje
=SwGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
Use the semihosting_enabled function to determine whether or not to
enable semihosting devices. This allows for graceful fallback in the
event a debugger is not attached.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
This adds support for booting entirely from JTAG while using a
hard-coded RCW. With these steps, it is not necessary to program a
"good" RCW using CodeWarrior. The method here can be performed with any
JTAG adapter supported by OpenOCD, including the on-board CMSIS-DAP
(albeit very slowly).
These steps require LS1046A support in OpenOCD, which was added in [1].
[1] 5b70c1f679/
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
[trini: Add reference to doc/board/nxp/ls1046ardb.rst]
This converts the readme for this board to rST. I have tried not to
change any semantics from the original (though I did convert MB to M).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
So far the DRAM size for both the Juno and the FVP model were hardcoded
in our config header file. For the Juno this is fine, as all models have
8 GiB of DRAM, but the DRAM size can be configured on the model command
line.
Drop the fixed DRAM size setup, instead look up the size in the device
tree, that we now have for every board. This allows a user to inject
a DT with the proper size, and be able to use the full amount of DRAM.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In preparation for the ARMv8-R64 FVP support, which has DRAM mapped at
0x0, generalise the page table generation, by using symbolic names for
the address ranges instead of fixed numbers.
We already define the base of the DRAM and MMIO regions, so just use
those symbols in the page table description. Rename V2M_BASE to the more
speaking V2M_DRAM_BASE on the way.
On the VExpress memory map, the address space right after 4GB is of no
particular interest to software, as the whole of DRAM is mapped at 32GB
instead. The first 2 GB alias to the lower 2GB of DRAM mapped below 4GB,
so we skip this part and map some more of the high DRAM, should anyone
need it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The defconfigs for the Arm Juno board and the FVP model are quite large,
setting a lot of platform-fixed variables like SYS_TEXT_BASE.
As those values are not really a user choice, let's provide default
values for them in our Kconfig file, so a lot of cruft can be removed
from the defconfig files.
This also moves the driver selection out of there, since this is again
not something a user should really decide on. Instead we allow users to
enable or disable subsystems, and select the appropriate drivers based
on that in the Kconfig file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The FVP base model is relying on a DT for Linux operation, so there is
no reason we would need to rely on hardcoded information for U-Boot.
Letting U-Boot use a DT will open up the usage of actual peripherals,
beyond the support for semihosting only.
Enable OF_CONTROL in the Kconfig, and use the latest dts files from
Linux. Depending on whether we use the boot-wrapper or TF-A, there is
already a DTB provided or not, respectively.
To cover the boot-wrapper, we add an arm64 Linux kernel header, which
allows the boot-wrapper to treat U-Boot like a Linux kernel. U-Boot will
find the pointer to the DTB in x0, and will use it.
Even though TF-A carries a DT, at the moment this is not made available
to non-secure world, so to not break users, we use the U-Boot provided
DTB copy in that case. For some reason TF-A puts some DT like structure
at the address x0 is pointing at, but that is very small and doesn't
carry any hardware information. Make the code to ignore those small DTBs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
At the moment we define three "VExpress64" boards in arch/arm/Kconfig,
plus have a second Kconfig file in board/armltd/Kconfig.
One of those three boards is actually bogus (TARGET_VEXPRESS64_AEMV8A),
that stanza looks like being forgotten in a previous cleanup.
To remove the clutter from the generic Kconfig file, just define some
ARCH_VEXPRESS64 symbol there, enable some common options, and do the
board/model specific configuration in the board/armltd Kconfig file.
That allows to streamline and fine tune the configuration later, and
to also pull a lot of "non user choices" out of the defconfigs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This converts the following to Kconfig:
CONFIG_NORFLASH_PS32BIT
Note that we also attempt to correct the behavior of the code here,
which had been testing for "NORFLASH_PS32BIT" which would never be set,
instead check for the now set "CONFIG_NORFLASH_PS32BIT", which results
in some behavior change.
Cc: TsiChung Liew <Tsi-Chung.Liew@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_LSCHLV2
CONFIG_LSXHL
Cc: Michael Walle <michael@walle.cc>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Michael Walle <michael@walle.cc>
This CONFIG option is used in one place, so pick a more direct name and
migrate to Kconfig. Rework the code slightly.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_KM_COGE5UN
CONFIG_KM_KIRKWOOD_128M16
CONFIG_KM_KIRKWOOD
CONFIG_KM_KIRKWOOD_PCI
CONFIG_KM_NUSA
CONFIG_KM_SUSE2
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
The only usage of CONFIG_KMTEGR1 can be replaced by
CONFIG_TARGET_KMTEGR1 so do so and remove this other symbol.
Cc: Holger Brunck <holger.brunck@hitachienergy.com>
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Holger Brunck <holger.brunck@hitachienergy.com>
This platform is the only one to set these options, so define them in
the board Kconfig file.
Cc: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Tom Rini <trini@konsulko.com>
Both of these variables are used in a few hard-coded ways to set some
string values or print something to the user. In almost all cases, it's
just as useful to hard-code the value used. The exception here is
printing something closer to correct board name for p1_p2_rdb machines.
This can be done using something from the device tree, but for now
hard-code a non-CONFIG based value instead.
Signed-off-by: Tom Rini <trini@konsulko.com>
Set blue led on at boot time in order to highlight that u-boot is loaded.
This is done for all sama5d2 based boards which contain an RGB led.
Signed-off-by: Mihai Sain <mihai.sain@microchip.com>
The QEMU platform has a function defined to get the random number
generator(RNG) device. However, the RNG device can be obtained simply
by searching for a device belonging to the RNG uclass. Remove the
superfluous platform function defined for the QEMU platform for
getting the RNG device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The SPL does not update the memory node with the dram size from EEPROM
but instead we can use get_ram_size which does a simple memory test
to determine the available RAM. Update PHYS_SDRAM_SIZE to 4GiB as that
is the max used on the Venice boards.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
commit 7c84319af9c7 ("dm: gpio: Correct use of -ENODEV in drivers")
changed the return code for an I2C NAK from -ENODEV to -EREMOTEIO.
Update the gsc_i2c_read and gsc_i2c_write functions for this change
to properly retry the transaction on a NAK meaning the GSC is busy.
Fixes: 7c84319af9 ("dm: gpio: Correct use of -ENODEV in drivers")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Versal can also have reserved space in DT which u-boot has to avoid to
placing self to that location. The same change was done in ZynqMP by commit
ce39ee28ec ("zynqmp: Do not place u-boot to reserved memory location")
and also for microblaze by commit d7b5cc89d3 ("microblaze: Do not place
u-boot to reserved memory location").
The patch was tested by adding reserved-memory node to DT and check via
bdinfo back.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/15426fa6d64835dd23c5c8c12bbfc97306fb6098.1647527129.git.michal.simek@xilinx.com
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
This does not use driver model and is more than two years past the
migration date. Drop it.
It can be added back later if needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop the Kconfigs which are not used and all references to them. In
particular, this drops CONFIG_VIDEO to avoid confusion and allow us to
eventually rename CONFIG_DM_VIDEO to CONFIG_VIDEO.
Also drop the prototype for video_get_info_str() which is no-longer used.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jason Liu <jason.hui.liu@nxp.com>
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.
Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.
This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
Add following two new PCI class codes defines into pci_ids.h include file:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
And use these defines in all U-Boot code for describing PCI class codes for
normal and subtractive PCI bridges.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
This converts the following to Kconfig:
CONFIG_LCD_INFO
CONFIG_LCD_LOGO
CONFIG_LCD_INFO_BELOW_LOGO
CONFIG_LCD_IN_PSRAM
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ATMEL_LCD
CONFIG_ATMEL_LCD_BGR555
CONFIG_ATMEL_LCD_RGB565
CONFIG_GURNARD_SPLASH
Signed-off-by: Tom Rini <trini@konsulko.com>
This variable is used once and is noted as board-specific. Use the
value directly with a comment.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This symbol is used only once, and in comparison with an unset symbol,
so drop it.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G10EK
CONFIG_AT91SAM9261EK
CONFIG_AT91SAM9G10
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_AT91SAM9G20EK
CONFIG_AT91SAM9260EK
CONFIG_AT91SAM9G20EK_2MMC
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
A small number of i.MX6/7 and vf610 boards have not enabled DM_ETH yet.
Given the state of the rest of the platform, enable DM_ETH.
Cc: Alison Wang <alison.wang@nxp.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Richard Hu <richard.hu@technexion.com>
Cc: Troy Kisky <troy.kisky@boundarydevices.com>
Cc: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
The RK3399 SoC needs to know the voltage value provided by some
regulators, which is done by setting relevant register bits. Configure
these the way other RK3399 boards do, but with the same values as are
set in the equivalent code in coreboot.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
stm32mp1 bsec: Add permanent lock write support
stm32mp1 bsec: Add dev in function description
cmd_stboard: Update test on misc_read() result
video: fix the check of return value of clk_set_rate in stm32_ltdc
DT: Alignment with kernel v5.17 for stm32mp15
DT: Add USB OTG pinctrl and regulator in SPL for DHCOR
DT: Move vdd_io extras into Avenger96 extras
DT: Add DFU support for DHCOM recovery
ram: stm32mp1: Unconditionally enable ASR
psci: Implement PSCI system suspend and DRAM SSR for stm32mp
-----BEGIN PGP SIGNATURE-----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=H4+P
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20220315' of https://source.denx.de/u-boot/custodians/u-boot-stm
mtd: add NAND write protect support to stm32_fmc2_nand
stm32mp1 bsec: Add permanent lock write support
stm32mp1 bsec: Add dev in function description
cmd_stboard: Update test on misc_read() result
video: fix the check of return value of clk_set_rate in stm32_ltdc
DT: Alignment with kernel v5.17 for stm32mp15
DT: Add USB OTG pinctrl and regulator in SPL for DHCOR
DT: Move vdd_io extras into Avenger96 extras
DT: Add DFU support for DHCOM recovery
ram: stm32mp1: Unconditionally enable ASR
psci: Implement PSCI system suspend and DRAM SSR for stm32mp
"kendryte" is the marketing name for the K210 RISC-V SoC produced by
Canaan Inc. Rather than "kendryte,k210", use the usual "canaan,k210"
vendor,SoC compatibility string format in the device tree files and
use the SoC name for file names.
With these changes, the device tree files are more in sync with the
Linux kernel DTS and drivers, making uboot device tree usable by the
kernel.
Signed-off-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: Niklas Cassel <niklas.cassel@wdc.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
Update management of misc_read/misc_write, which now returns length of
data after the commit 8729b1ae2c ("misc: Update read() and write()
methods to return bytes xfered"): raise a error when the result is not
the expected length.
Fixes: 658fde8a36 ("board: stm32mp1: stboard: lock the OTP after programming")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
- convert Nokia RX-51 to CONFIG_DM_VIDEO
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCYi+zvw4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXIReAJ9JS06uOjNFmOBdfpsOI2jnVdWABQCbB8nvUh19
jbftZtj+18fhFuNb1r4=
=3vpL
-----END PGP SIGNATURE-----
Merge tag 'video-20220314' of https://source.denx.de/u-boot/custodians/u-boot-video
- fix display of the u-boot logo on Apple devices
- convert Nokia RX-51 to CONFIG_DM_VIDEO
Initialization and power on operations of links have been moved under the
link device in the Sierra SerDes driver. Also, the UCLASS of
sierra_phy_provider has been changed to UCLASS_MISC.
Therefore, fix the probing of SerDes0 instance accordingly.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Georgi Vlaev <g-vlaev@ti.com>
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
With updated device trees now supporting pinmuxing for USB,
ethernet, MMC, and other peripherals necessary to start MLO
and U-Boot, the hard-coded pinmux options can be removed since
they are now handed by DM and only muxed when the respective
peripheral needs it.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
With recent fixes to USB pinmuxing in the device trees, there
is no need to hard-code the pinmuxing in this table. It is
all handled in DM now.
Signed-off-by: Adam Ford <aford173@gmail.com>
The ethernet controller is DM compliant, and the device tree
defines it. There is no need to manually handle pulling
the ethernet out of reset.
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Derald D. Woods <woods.technical@gmail.com>
The PMIC enables power to the MMC card by default, but depending
on the state it was left when restarted, it's possible the MMC
may be powered down.
This patch patch explicitly tells the twl4030 to power the MMC.
Based on commits [1][2].
[1] 64fd2d2614
[2] 27b6534491
Signed-off-by: Romain Naour <romain.naour@gmail.com>
With DM_MMC working for both SPL and U-Boot, this patch removes
the legacy style of initializing the MMC driver.
Based on omap3_logic: 42140dd096.
Signed-off-by: Romain Naour <romain.naour@gmail.com>
This hook can be implmented using events, for the three boards that
actually use it.
Add the event type and event handlers. Drop CONFIG_MISC_INIT_F since we
can just use CONFIG_EVENT to control this. Since sandbox always enables
CONFIG_EVENT, we can drop the defconfig lines there too.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently we only support to load the environment from raw MMC or FAT
locations on Allwinner boards. With the advent of SPI flash we probably
also want to support using the environment there, so we need to become
a bit more flexible.
Change the environment priority function to take the boot source into
account. When booted from eMMC or SD card, we use FAT or MMC, if
configured, as before.
If we are booted from SPI flash, we try to use the environment from
there, if possible. The same is true for NAND flash booting, although
this is somewhat theoretical right now (as untested).
This way we can use the same image for SD and SPI flash booting, which
allows us to simply copy a booted image from SD card to the SPI flash,
for instance.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Mechanically convert video_hw_init() function to UCLASS_VIDEO probe
callback and replace CONFIG_CFB_CONSOLE by CONFIG_DM_VIDEO.
As framebuffer base address is setup by the bootloader which loads U-Boot,
set plat->base to that fixed framebuffer address.
This change was tested in qemu n900 machine and is working fine.
What does not work is CONFIG_VIDEO_LOGO, seems to be buggy.
Signed-off-by: Pali Rohár <pali@kernel.org>
Since commit 5d94cbd1dc ("scripts: Makefile.lib: generate
dsdt_generated.c instead of dsdt.c"), the file generated
is named dsdt_generated.c instead of dsdt.c.
So all files .gitignore referencing dsdt.c should be
upated with dsdt_generated.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Add support to read MAC addresses from mac address multirecord.
Check if multi record is found, then jump to mac address multirecord by
comparing the record type field. If it matches mac address
multirecord(0xD2), then copy mac addresses.
Copy these read MAC address in xilinx_read_eeprom_fru so that they are
updated to eth*addr in board_late_init_xilinx().
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/18f31bc528820934854ea5fd9dc581778fc1e40c.1645624855.git.michal.simek@xilinx.com
In board_late_init_xilinx() eth*addr are updated from the values read from
eeprom. Ideally the MAC addresses are updated sequencially. So if any
MAC address is invalid, it means there are no further valid values.
So optimise this logic by replacing continue with break.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/efef0d07add5d5777396ea111ad75411dc402db3.1645624855.git.michal.simek@xilinx.com
fru_checksum function is simply adding all the bytes and returning the
sum. If the data passed to this function is all zero's then it will
return 0, and the functions calling this api will assume that checksum
is correct. Ideally this is not good. Fix this by returning error if all
the data is 0's.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/ac0366fe55c60a818a3f9ed33d96826c817d5520.1645624855.git.michal.simek@xilinx.com
We only want to call do_board_detect() if CONFIG_TI_I2C_BOARD_DETECT
is set. Same as done for am64.
This makes it possible to add a custom am65 based board design to
U-Boot that does not use this board detection mechanism.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Commit 369e532691 ("ddr: marvell: a38x: allow board specific ODT
configuration") added the odt_config member to struct
mv_ddr_topology_map ahead of the clk_enable and ck_delay members. This
means that any boards that configured either of clk_enable or ck_delay
needed to have their board topology updated. This affects the x530 and
clearfog boards. Other A38x boards don't touch any of the trailing
members of mv_ddr_topology_map so don't need updating.
Fixes: 369e532691 ("ddr: marvell: a38x: allow board specific ODT configuration")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
The branch_if_master macro jumps to a label if the CPU is the "master"
core, which we define as having all affinity levels set to 0. To check
for this condition, we need to mask off some bits from the MPIDR
register, then compare the remaining register value against zero.
The implementation of this was slighly broken (it preserved the upper
RES0 bits), overly complicated and hard to understand, especially since
it lacked comments. The same was true for the very similar
branch_if_slave macro.
Use a much shorter assembly sequence for those checks, use the same
masking for both macros (just negate the final branch), and put some
comments on them, to make it clear what the code does.
This allows to drop the second temporary register for branch_if_master,
so we adjust all call sites as well.
Also use the opportunity to remove a misleading comment: the macro
works fine on SoCs with multiple clusters. Judging by the commit
message, the original problem with the Juno SoC stems from the fact that
the master CPU *can* be configured to be from cluster 1, so the
assumption that the master CPU has all affinity values set to 0 does not
hold there. But this is already mentioned above in a comment, so remove
the extra comment.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch scans the cmdline from the Samsung SBL (second stage
bootloader) and stores the parameters board_id=N and lcdtype=N
in order to augment the DTB for different board and LCD types.
We then add a custom ft_board_setup() callback that will inspect
the DTB and patch it using the stored LCD type. At this point
we know which product we are dealing with, so using the passed
board_id we can also print the board variant for diagnostics.
We patch the Codina, Skomer and Kyle DTBs to use the right
LCD type as passed in lcdtype from the SBL.
This also creates an infrastructure for handling any other
Samsung U8500 board variants that may need a slightly augmented
DTB.
Cc: Markuss Broks <markuss.broks@gmail.com>
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To make sure we get a working console as soon as possible in the SPL the
UART pins require to be configured earlier. This is especially
true for the pins of UART3, since the PDU001 board uses this UART for
the console by default.
Signed-off-by: Felix Brack <fb@ltec.ch>
The changes from commit 0dba45864b ("arm: Init the debug UART")
prevent the early debug UART from being initialized correctly.
To fix this we not just configure the pin multiplexer but add setting up
early clocks.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This board has an internal watchdog which supervises the board startup.
Although, the initial state of the watchdog is configurable, it is
enabled by default. In board_late_init(), which means almost everything
worked as expected, disable the watchdog.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Most of the time it is very useful to have the version of the board
management controller. Now that we have a driver, print it during
startup.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The current console output is:
DRAM: 4 GiB
DDR 4 GiB (DDR3, 32-bit, CL=11, ECC on)
The size is printed twice and we can save one line of console output if
we join both lines. The new output is as follows:
DRAM: 4 GiB (DDR3, 32-bit, CL=11, ECC on)
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is a conflict between the static file
lib/acpi/dsdt.c and the file dsdt.c generated
dynamicaly by scripts/Makefile.lib. When a
mrproper is done, the static file dsdt.c is
removed. If a build with acpi enabled is
launched after, the following error is raised:
CC lib/acpi/acpi_table.o
make[2]: *** No rule to make target 'lib/acpi/dsdt.asl', needed by 'lib/acpi/dsdt.c'. Stop.
scripts/Makefile.build:394: recipe for target 'lib/acpi' failed
To avoid such error, the generated file is named
dsdt_generated.c instead of dstdt.c.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
The commit 0dba45864b ("arm: Init the debug UART") calls
debug_uart_init() from crt0.S but it won't work because SOC is not
configured yet. That's why create board_debug_uart_init() which calls
psu_init() via new psu_uboot_init() earlier before the first access to UART
in SPL. In full U-Boot call psu_uboot_init() only when
CONFIG_ZYNQMP_PSU_INIT_ENABLED is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/878dc2daaa8685346f889989fbfb98b2e44da7fb.1645104518.git.michal.simek@xilinx.com
ZYNQMP_PSU_INIT_ENABLED is called only when BOARD_EARLY_INIT_F is defined
that's why cover this dependency in Kconfig.
board_early_init_f() is only part related to
CONFIG_ZYNQMP_PSU_INIT_ENABLED which is disabled now that's why disable
BOARD_EARLY_INIT_F and also build board_early_init_f() only when
CONFIG_BOARD_EARLY_INIT_F is enabled.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/d89253ec1590cd513dcd4bfbedebae618bd6d605.1645104518.git.michal.simek@xilinx.com
The commit 9855034397 ("fdt: Don't call board_fdt_blob_setup() without
OF_BOARD") forced to enable OF_BOARD for platforms which provide DT
externally. Zynq/ZynqMP boards are using this feature for a long time
that's why there is a need to enable it by default.
Also code expects to return error in case of error that's why also fill it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/9f11bbffe2849f4da7d72712082d579262fe8fd8.1645104518.git.michal.simek@xilinx.com
Add support for ethernet on the imx8mn-ddr4-evk.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The function wrongly will return the card detection status of the SD card
(USDHC2) for the eMMC (USDHC1). Thus booting from eMMC without an inserted
SD card will fail.
Signed-off-by: Heiko Thiery <heiko.thiery@gmail.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
With binman generating flash.bin, it's not longer necessary to
specify either the location of ATF nor is it necessary to
specify building flash.bin, so let's update the build instructions
to remove those. While in here, update the revision of ATF and
DDR firmware so both Mini and Nano reference the same revision.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Use IS_ENABLED(CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG) to make the code
more readable and fix checkpatch.pl warning
Signed-off-by: Tommaso Merciai <tomm.merciai@gmail.com>
- a37xx: pci: Cleanup and minor fix for root port check (Pali)
- pci: mvebu: Ensure that root port is always on root zero bus (Pali)
- kwbimage: Fix dumping DATA registers for v0 images (Pali)
- kwbimage: Support for parsing extended v0 format (Pali)
- a37xx: Fix code and update DTS files to upstream version (Pali)
- a37xx: Fix and extend building memory map (Pali)
- ddr: marvell: a38x: fix BYTE_HOMOGENEOUS_SPLIT_OUT decision (Marek)
- mvebu: Optionally reset board on DDR training failure (Marek)
Armada 3720 DTS files in upstream kernel use ethernet nodes named
'ethernet@30000' and 'ethernet@40000'. U-Boot have them named 'neta@30000'
and 'neta@40000'. To have Turris Mox U-Boot board code independent of
ethernet node names, find ethernet node via alias.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Update the board_fit_config_name_match() to choose the right dtb
based on the board name read from EEPROM.
Also restrict multpile EEPROM reads by verifying if EEPROM is already
read.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
j721e-sk doesn't have any daughter cards, so disable daughter
card probing inside board_late_init() and spl_board_init() for
j721e-sk.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
J721E EVM has EEPROM populated at 0x50. J721E SK has EEPROM populated
at next address 0x51 in order to be compatible with RPi. So start
looking for TI specific EEPROM at 0x50, if not found look for EEPROM at
0x51.
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
board_late_init(), setup_board_eeprom_env() and setup_serial() is
called only under CONFIG_BOARD_LATE_INIT, so guard these functions
with the same. Also, reorder these functions to place it under
single #ifdef
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
The Pogoplug E02 board has the network chip Marvell 88E1116R. Convert
to Driver Model and use uclass mvgbe and the compatible driver M88E1118R
to bring up Ethernet.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- As the result of the migration to Driver Model, this u-boot image has
grown substantially (about 100K, give or take). The old envs location
at 0x60000 (384k) is no longer possible. Move it to 0xC0000 (768K).
- Miscellaneous changes: Move constants to .c file and remove header file
board/cloudengines/pogo_e02/pogo_e02.h, use CONFIG_SYS_THUMB_BUILD to
keep u-boot image under 512K, use BIT macro, and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Dockstar board has the network chip Marvell 88E1116R. Convert to
Ethernet driver model, and use uclass mvgbe and the compatible driver
M88E1118R to bring up Ethernet.
- Add CONFIG_DM_ETH and associated configs.
- Add board_eth_init() to use uclass mvgbe to bring up the network.
And remove ad-hoc code.
- Add CONFIG_PHY_MARVELL to properly configure the network.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Miscellaneous changes: Move constants to .c file and remove
header file board/Seagate/dockstar/dockstar.h, use
CONFIG_SYS_THUMB_BUILD to keep u-boot image
under 512K, add CONFIG_HUSH_PARSER, use BIT macro, and cleanup comments.
- Note: This patch is a RESEND for a previous patch:
https://patchwork.ozlabs.org/project/uboot/patch/20210812051854.1340-2-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init(), CONFIG_DM_ETH, and CONFIG_PHY_MARVELL
to bring up Ethernet.
- Miscellaneous changes: Move constants to .c file and remove header file
board/iomega/iconnect/iconnect.h. Add CONFIG_HUSH_PARSER, use BIT macro,
and cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Globalscale Technologies Dreamplug board has the network chip
Marvell 88E1116R. Use uclass mvgbe and the compatible driver M88E1310
driver to bring up Ethernet.
- Currently, CONFIG_RESET_PHY_R symbol is used in
arch/arm/mach-kirkwood/include/mach/config.h for all Kirkwood
boards with mv8831116 PHY, with each board defines the function
reset_phy(). Undefine it for this board.
- Add board_eth_init() to use uclass mvgbe to bring up both network
port 0 and 1. And remove ad-hoc code.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add myself as maintainer (this board seems to be orphaned,
could not contact Jason Cooper using current email).
- Miscellaneous changes: Move constants to .c file and remove header file
board/Marvell/dreamplug/dreamplug.h, cleanup comments.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Currently, if MTD NOR is enabled then U-Boot tries to issue flash
commands even when CFI flash DT node is not present. This causes
access fault on RISC-V emulators or ISS which do not emulate CFI
flash. To handle this issue, we implement is_flash_available() for
qemu-riscv board which will return 1 only if CFI flash DT node is
present.
Fixes: d248627f9d ("riscv: qemu: Enable MTD NOR flash support")
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable support for HTIF console so that we can use QEMU RISC-V U-Boot
on RISC-V emulators and ISS having it.
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This is supposed to be a build-system flag. Move it there so we can
define it before linux/kconfig.h is included.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The function to return the default MMC device for the environment
already has a __weak instance doing exactly the same thing. Remove
the superfluous one.
Signed-off-by: Adam Ford <aford173@gmail.com>
The function to return the default MMC device for the environment
already has a __weak instance doing exactly the same thing. Remove
the superfluous one.
Signed-off-by: Adam Ford <aford173@gmail.com>
Sync with the latest DDR initialization from Phytec, which
uses version 1.2 of NXP's i.MX7D DRAM Register Programming Aid
spreadsheet.
This updated DDR initialization fixes occasional system freeze.
Signed-off-by: Fabio Estevam <festevam@denx.de>
As suggested in commit 028abfd9b1 ("imx8mm-evk: Generate a single
bootable flash.bin again") for imx8mm_evk, it is possible to produce
single bootable image via binman. This restores the original behavior in
distros, where only one boot container is used to create target image.
Perform similar adaptions in order to provide single bootable image for
imx8mn-ddr4-evk derivate.
Update documentation to drop additional step of copying u-boot.itb
Fixes: 353dfe4b43 ("imx8mn-ddr4-evk: switch to use binman")
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The new configs/imx28_xea_sb_defconfig is introduced to facilitate
building the single binary u-boot.sb fox XEA board.
The biggest distinction from "normal" XEA imx28_xea_sb_defconfig is
support for USB mass storage devices (pen drives).
To achieve that, the CONFIG_DM_USB is enabled and supported.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This change provides the possibility to build XEA (imx287 based) board
U-Boot as a single binary (without support for CONFIG_SPL_FRAMEWORK).
The generated u-boot.sb can be used in the factory environment to for
example perform initial setup or HW testing.
It can be used with 'uuu' utility
(SDPS: boot -f /srv/tftp/xea/u-boot.sb)
In the configs/imx28_xea_defconfig one needs to disable following configs:
# CONFIG_SPL_BLK is not set
# CONFIG_SPL_FRAMEWORK is not set
The board_init_ll() is used in arch/arm/cpu/arm926ejs/mxs/start.S, which
is utilized when CONFIG_SPL_FRAMEWORK is disabled.
However, when it is enabled - the arch/arm/cpu/arm926ejs/start.S is used,
which requires the lowlevel_init() function.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Extension boards can be added to Compulab's iot-gate-imx8mm.
We implement extension board manager for detecting the extension
boards.
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: uboot-imx <uboot-imx@nxp.com>
8ULP ROM should read the LPOSC trim BIAS fuse to fill the CGC0
LPOSCCTRL[7:0], but it writes a fixed value on A0.1 revision.
A0.2 will fix the issue in ROM. But A0.1 we have to workaround
it in SPL by setting LPOSCCTRL BIASCURRENT again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The setting does not have effect because we should set it after
power on the PS16 for NIC AV.
So move it after upower_init which has powered on all PS
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board use IO9 of PCA6416 on LPI2C0 and TPM0 for MIPI DSI MUX and
backlight. However the LPI2C0 and TPM0 are M33 resources, in this
patch we simply access them, but this is a temporary solution.
We will modify it when M33 FW changes to set MIPI DSI panel as default
path and enable backlight after reset.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add EA iMX7ULP COM board support for building SPL.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
This is the promised second part of the sunxi PR for 2022.04, albeit
technially outside of the merge window. We were working on this full
steam since the beginning of the year, and it deserves to be merged,
I think.
The main attraction is support for the F1C100s SoC, which sports a
venerable ARM926 core. Support for this SoC and the LicheePi Nano board
has been in Linux for years, and U-Boot patches were posted mid last
year already.
The new SoC using ARMv5 also means that the bulk of the new code should
not touch any existing boards, although we did some refactorings first,
of course, which actually cleans up some existing sunxi code.
Compile tested for all 160 sunxi boards, and briefly tested on BananaPi M1,
OrangePi Zero, Pine64 and Pine-H64. Tested by others on their boards,
including F1C100s and F1C200s devices.
Generic Timer Extension is not available on SUNIV.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add the PDU001 board specific DT files to MAINTAINERS. This should
help for better tracking of changes to these files.
Signed-off-by: Felix Brack <fb@ltec.ch>
The available ram can be limited by ram_top as that depends on the
reserved memory nodes provided by the device-tree (via
board_get_usable_ram_top), so make sure to respect ram_top when setting
up bootm_size to avoid overlapping reserved memory regions (e.g. memory
used by OP-TEE).
The same logic is available in env_get_bootm_size when bootm_size is
not defined by the default environment.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Link: https://lore.kernel.org/r/20220120191730.2009270-1-ricardo@foundries.io
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Commit 045ecf8992 ("configs: enable DM_ETH support for LS1046ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
IFC-NOR and QSPI are muxed on SoC.
So disable IFC node in dts if QSPI is enabled or disable QSPI node in dts
in case QSPI is not enabled.
"ifc/nor" will be changed to "memory-controller/nor" in linux. So need to
modify "ifc/nor" to "memory-controller/nor" in fdt_path_offset().
Signed-off-by: Jianpeng Bu <jianpeng.bu@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Commit eb1986804d ("configs: enable DM_ETH support for LS1043ARDB")
resulted in the PCI bus no longer being implicitly enumerated.
However, this is necessary for the fdt pcie fixups to work.
Therefore, similar to commit 8b6558bd41 ("board: ls1088ardb:
transition to DM_ETH"), pci_init() is now called in the board_init()
routine when CONFIG_DM_ETH is active.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
CC: Priyanka Jain <priyanka.jain@nxp.com>
CC: Camelia Groza <camelia.groza@nxp.com>
Acked-by: Camelia Groza <camelia.groza@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The SCRATCHRW4 is only used in secure boot scenario that is unsupported by
our design, so this address can be stolen for storing POST status.
The SCRATCHRW4 is initialized to zero at core rest.
Using a DDR address was unfortunate choice, the DDR at boot time has a
random contend and it happens that sometimes is matching POST magic number.
This behavior can lead to undefined POST behavior and u-boot ending in
failbootcmd command.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This was probably broken when mainlining, CONFIG_FSL_DEVICE_DISABLE is
not Kconfig but whitelisted.
It's fine to be without flag as this is always enabled for abec1020
(pg-wcom-ls102xa.h)
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch adds default defconfig for u-boot update version, the u-boot
update defconfig is a copy of the default (factory) defconfig with:
- adapted text base and environment addresses
- explicit flag that this is a field updated u-boot version
At the time of implementation this version is only used to verify the
update procedure, in future depend on the needs this defconfig can be
extended with additional options.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Field fail-safe u-boot update procedure for pg-wcom boards is defined and
implemented by patch: 59b3403.
This patch invokes the update procedure for pg-wcom-ls102x designs during
early misc_init_f execution.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This patch provides possibility for field fail-safe u-boot updates.
The implementation can be used on all pg-wcom boards that are booting from
parallel NOR flash.
When used in a board design, provided check_for_uboot_update function will
start new u-boot at defined location if updateduboot envvar is set to yes.
With this implementation it is expected that factory programmed u-boot
will always stay as it is, and optionally new u-boot can be safely
programmed by embedded software when the unit is rolled out on the field.
It is expected check_for_uboot_update to be called early in execution
before relocation (*_f) once SoC is basically initialized and environment
can be read, with this possibilities to not be able to fix a u-boot bug by
a u-boot update are reduced to minimum.
Signed-off-by: Aleksandar Gerasimovski <aleksandar.gerasimovski@hitachienergy.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
