This adds stack layer for eXtensible Host Controller Interface
which facilitates use of USB 3.0 in host mode.
Adapting xHCI host controller driver in linux-kernel
by Sarah Sharp to needs in u-boot.
Initial porting from Linux kernel version 3.4, with following
top commit history of drivers/usb/host/xhci* :
cf84055 xHCI: Cleanup isoc transfer ring when TD length mismatch found
This adds the basic xHCI host controller driver with bare minimum
features:
- Control/Bulk transfer support has been added with required
infrastructure for necessary xHC data structures.
- Stream protocol hasn't been supported yet.
- No support for quirky devices has been added.
Signed-off-by: Vikas C Sajjan <vikas.sajjan@samsung.com>
Signed-off-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
Macros defining bmRequestType field of USB device request,
given in table 9.2 USB 2.0 spec, are rather generic macros
which can be further used by other Host controller stacks.
So moving them to usb_defs header.
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Julius Werner <jwerner@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Dan Murphy <dmurphy@ti.com>
Cc: Marek Vasut <marex@denx.de>
In case the MX23/MX28 is switched into JTAG mode via the BootMode select
switches, the BootROM bypasses the CPU core registers initialization.
This in turn means that the Stack Pointer (SP) register is not set as
it is in every other mode of operation, but instead is only zeroed out.
To prevent U-Boot SPL from crashing in this obscure JTAG mode, configure
the SP to point at the CONFIG_SYS_INIT_SP_ADDR if the SP is zeroed out.
Note that in case the SP is already configured, we must preserve that exact
SP value and must not modify it. This is important since in every other mode
but the JTAG mode, the SPL returns into the BootROM and BootROM in turn loads
U-Boot itself. If the SP were to be corrupted, the BootROM won't be able to
continue it's operation after returned from SPL and the system would crash.
Finally, add the JTAG mode switch identifier, so it's not recognised as
Unknown mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
This board supports FEC Ethernet, SPI NOR and NAND flash.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Christoph Baumann <c.baumann@ppc-ag.de>
Add basic support for mx6q udoo board.
For further information about Udoo board:
http://www.udoo.org/
Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Now that mkimage can generate an BootStream for i.MX23 and i.MX28,
use the mkimage as a default tool to generate the BootStreams instead
of the elftosb tool. This cuts out another obscure dependency.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Remove Prodrive pdnb3 board (including the scpu variant) support
from mainline. As its unmaintained and not needed any more for
quite some time.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Martijn de Gouw <martijn.de.gouw@prodrive.nl>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Zynq lowlevel_init() was implemented in C but stack
pointer is setup after function call in _main().
Move architecture setup to arch_cpu_init() which is call
as the first function in board_init_f() which
already have correct stack pointer.
Reported-by: Sven Schwermer <sven.schwermer@tuhh.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The prototype of handlers had changed.
This commit uses cast with (void *) rather than
the handler-specific prototype.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add support for hsi2c controller available on exynos5420.
Note: driver currently supports only fast speed mode 100kbps
Change-Id: I02555b1dc8f4ac21c50aa5158179768563c92f43
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: R. Chandrasekar <rc.sekar@samsung.com>
At present the i2c ports are enumerated in a strange way - the
fdtdec_find_aliases_for_id() function is used, but then the ID returned
is ignored and the ports are renumbered. The effect is the same provided
that the device tree has the ports in the same order, or uses aliases,
and has no gaps, but it is not correct.
Adjust the code to use the function as intended. This will allows device
tree aliases to change the device order if required.
As a result, the i2c_busses variable is dropped. We can't be sure that
there are no 'holes' in the list of buses, so must check the whole
array.
Note: it seems that non-FDT operation is now broken in this drive and
will need to be reinstated for upstream.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-on: https://gerrit.chromium.org/gerrit/59369
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
The Exynos5 i2c driver does not handle NACKs properly. This change:
- fixes the NACK processing problem (do not continue transaction if
address cycle was NACKed)
- eliminates a fair amount of duplicate code
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Reviewed-by: Simon Glass <sjg@google.com>
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
NoMMU systems have a access violation problem with i2c_reloc_fixup.
Blame for it is a double relocation of the adapter itself. The
i2c_adap_p is already relocated, if i2c_reloc_fixup is called.
This patch removes the relocation of i2c_adap_p from i2c_reloc_fixup
to fix this.
Signed-off-by: Jens Scharsig (BuS Elektronik) <esw@bus-elektronik.de>
If user uses the I2C in before the relocation, board of sh and rmobile
will not start. This will solve this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
check first, if we are on the bus, we want to enable. If so,
return immediately, do not calc max adapter number, nor check
other things.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
(Interface is not quite the same as Phillips PCA9547.)
Signed-off-by: Michael Burr <michael.burr@logicpd.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
On generic board, the i2c init initialize only
one bus. But the new i2c subsystem allow to
manage severals i2c bus. So in the case, instead
of initializing a bus, we just set the current
i2c bus. The initialization will be done in
the i2c command.
Signed-off-by: Philippe Reynes <tremyfr@yahoo.fr>
This adds the preset value to register, and setup of baudrate.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This changes clock definition of SCIF from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_SCIF_CLK_FREQ, and clock definition of TMU from CONFIG_SYS_CLK_FREQ to
CONFIG_SH_TMU_CLK_FREQ for boards.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
The former SH/SCIF driver had calculated baudrate based on CONFIG_SYS_CLK_FREQ.
The newest SH/SCIF needs calculation of the clock for SCIF.
This patch defines clock CONFIG_SH_SCIF_CLK_FREQ for SCIF and changes it to
CONFIG_SH_SCIF_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
The former SH/TMU driver had calculated timer based on CONFIG_SYS_CLK_FREQ.
The newest SH/TMU newly needs calculation of the clock for TMU.
This patch defines clock CONFIG_SH_TMU_CLK_FREQ for TMU and changes it to
CONFIG_SH_TMU_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
A chache API of SH is developped by reference in linux kernel.
And API was the same as the linux kernel.
This patch change cache API to defines as U-Boot.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
"static u16 bit" is not necessary to use this as static global variable.
This patch fixes this.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
timer_init function sets timer prescaler bit.
The previous code so did not mask this bit, this function was to overwrite
the bit. This will fix this problem.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Previously, the address of a requested capability is define like that
"#define PCI_DCR 0x78"
But, the addresses of capabilities is different with regard to PCIe revs.
So this method is not flexible.
Now a function to get the address of a requested capability is added and used.
It can get the address dynamically by capability ID.
The step of this function:
1. Read Status register in PCIe configuration space to confirm that
Capabilities List is valid.
2. Find the address of Capabilities Pointer Register.
3. Find the address of requested capability from the first capability.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Erratum A006379 says CPCHDBCR0 bit field [10:14] has incorrect default
value after POR. The workaround is to set this field before enabling
CPC to 0x1e.
Erratum A006379 applies to
T4240 rev 1.0
B4860 rev 1.0, 2.0
Signed-off-by: York Sun <yorksun@freescale.com>
- Rename old P1010RDB board as P1010RDB-PA.
- Add support for new P1010RDB-PB board.
- Some optimization.
For more details, see board/freescale/p1010rdb/README.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix conflicts in boards.cfg]
Acked-by: York Sun <yorksun@freescale.com>
Since pins multiplexing, SDHC shares signals with IFC, with this patch:
To enable SDHC in case of NOR/NAND/SPI boot
a) For temporary use case in runtime without reboot system
run 'mux sdhc' in u-boot to validate SDHC with invalidating IFC.
b) For long-term use case
set 'esdhc' in hwconfig and save it.
To enable IFC in case of SD boot
a) For temporary use case in runtime without reboot system
run 'mux ifc' in u-boot to validate IFC with invalidating SDHC.
b) For long-term use case
set 'ifc' in hwconfig and save it.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Some boards use System EEPROM with 128-bytes instead of 256-bytes.
Since we regard 256-bytes EEPROM as standard EEPROM with default
value for MAX_NUM_PORTS. For those non-256-bytes EEPROM, we can
redefine MAX_NUM_PORTS in board-specific file to override the
default MAX_NUM_PORTS.
This patch doesn't impact on previous existing boards.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
T1040QDS is a high-performance computing evaluation, development and
test platform supporting the T1040 QorIQ Power Architecture™ processor.
T1040QDS board Overview
-----------------------
- Four e5500 cores, each with a private 256 KB L2 cache
- 256 KB shared L3 CoreNet platform cache (CPC)
- Interconnect CoreNet platform
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving
support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
for the following functions:
- Packet parsing, classification, and distribution
- Queue management for scheduling, packet sequencing, and congestion
management
- Cryptography Acceleration
- RegEx Pattern Matching Acceleration
- IEEE Std 1588 support
- Hardware buffer management for buffer allocation and deallocation
- Ethernet interfaces
- Integrated 8-port Gigabit Ethernet switch
- Four 1 Gbps Ethernet controllers
- SERDES Connections, 8 lanes supporting:
— PCI Express: supporting Gen 1 and Gen 2;
— SGMII
— QSGMII
— SATA 2.0
— Aurora debug with dedicated connectors
- DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and
Interleaving
-IFC/Local Bus
- NAND flash: 8-bit, async, up to 2GB.
- NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB
- GASIC: Simple (minimal) target within Qixis FPGA
- PromJET rapid memory download support
- Ethernet
- Two on-board RGMII 10/100/1G ethernet ports.
- PHY #0 remains powered up during deep-sleep
- QIXIS System Logic FPGA
- Clocks
- System and DDR clock (SYSCLK, “DDRCLK”)
- SERDES clocks
- Power Supplies
- Video
- DIU supports video at up to 1280x1024x32bpp
- USB
- Supports two USB 2.0 ports with integrated PHYs
— Two type A ports with 5V@1.5A per port.
— Second port can be converted to OTG mini-AB
- SDHC
- SDHC port connects directly to an adapter card slot, featuring:
- Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC
— Supporting eMMC memory devices
- SPI
- On-board support of 3 different devices and sizes
- Other IO
- Two Serial ports
- ProfiBus port
- Four I2C ports
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: fix conflict in boards.cfg]
Acked-by-by: York Sun <yorksun@freescale.com>
Some DDR related structures present in fsl_ddr_dimm_params.h, fsl_ddr_sdram.h, ddr_spd.h
has various parameters with embedded acronyms capitalized that trigger the CamelCase
warning in checkpatch.pl
Convert those variable names to smallcase naming convention and modify all files
which are using these structures with modified structures.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Previous process of compiling a PBL boot image is:
1: make <board_name_config>
2: make u-boot.pbl
for example:
make T4240QDS_SDCARD_config
make u-boot.pbl
Now the process is:
1: make <board_name>
for example:
make T4240QDS_SDCARD
Also, updated README.pblimage.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Use a default RCW of protocol 0x2A_0x98, and a PBI configure file which
uses CPC1 as 512KB SRAM, then PBL tool can be used on B4860 to build a
pbl boot image.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Default configuration has been changed, the most important one is DDR
ref_clock which is changed from 66.67MHz to 133.33MHz. so the ratio need to
change from 24x to 12x to keep the DDR frequency. There are also some
other optimise to align with default configuration.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
For USB device-tree fix-up to work properly, its necessary to
mention USB1 options before that of USB2 inside default hwconfig
string
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Current IFC timings for NAND flash are not able to support existing
K9F1G08U0B and new K9F1G08U0D flash.
so Update the timings to support both.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Fix PHY addresses for QSGMII Riser Card working in
SGMII mode on board P3041/P5020/P4080/P5040/B4860.
QSGMII Riser Card can work in SGMII mode, but
having the different PHY addresses.
So the following steps should be done:
1. Confirm whether QSGMII Riser Card is used.
2. If yes, set the proper PHY address.
Generally, the function is_qsgmii_riser_card() is
for step 1, and set_sgmii_phy() for step 2.
However, there are still some special situations,
take P5040 and B4860 as examples, the PHY addresses
need to be changed when serdes protocol is changed,
so it is necessary to confirm the protocol before
setting PHY addresses.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
SGMII5/6 and SGMII7/8 are not on the same slot on P5040
according to the serdes protocol.
So it is not proper to organize SGMII5/6 and SGMII7/8
on one bus and SGMII5/6 can't work.
So a new bus SUPER_HYDRA_FM3_SGMII_MDIO is added for
SGMII5/6
Signed-off-by: Zhao Qiang <B45475@freescale.com>
