Commit graph

462 commits

Author SHA1 Message Date
Tom Rini
c956662cc3 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-02-10 10:42:22 -05:00
Tom Rini
307367eaff Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2015-02-10 10:40:43 -05:00
Graeme Russ
2d6286ab79 arm: mxs: Add 'Wait for JTAG user' if booted in JTAG mode
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)

Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:50 +01:00
Graeme Russ
7a08603707 arm: mxs: Enable booting of mx28 without battery
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.

This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
 - Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
 - Switch between 4P2 Linear Regulator and Battery, using whichever has
   the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
   the same as the pre-patch behaviour)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
2015-02-10 12:48:50 +01:00
Graeme Russ
950eaf6230 arm: mxs: Add debug outputs and comments to mxs SPL source files
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
 - Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
 - Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)

Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
2015-02-10 12:48:49 +01:00
Bo Shen
c6941e1203 ARM: atmel: cleanup: remove at91cap9 related code
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.

Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
2015-02-07 23:42:56 +01:00
Tom Rini
212324a9d4 davinci: Do not duplicate setting of gd
In f0c3a6c we stopped setting gd in board_init_f, but later had to
revert to due problems on certain platforms.  As davinci does not look
to have these problems, we can drop the setting here and rely upon
crt0.S to do it.

Cc: Peter Howard <pjh@northern-ridge.com.au>
Signed-off-by: Tom Rini <trini@ti.com>
2015-01-29 12:00:50 -05:00
Tom Rini
aed03faa06 Merge branch 'master' of git://git.denx.de/u-boot-atmel 2015-01-26 06:42:40 -05:00
Luka Perkov
62d1e990d9 ARM: kirkwood: fix cpu info for 6282 device id
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Stefan Roese <sr@denx.de>
2015-01-25 23:56:15 +01:00
Heiko Schocher
99197a9e31 arm, arm926ejs: make thumb mode compileable
in thumb mode compiler says for example for arch/arm/lib/cache-cp15.c
when enabling CONFIG_SYS_THUMB_BUILD:

{standard input}: Assembler messages:
{standard input}:373: Error: selected processor does not support Thumb mode `mrc p15,0,r4,c1,c0,0'
{standard input}:416: Error: selected processor does not support Thumb mode `mcr p15,0,r3,c2,c0,0'

so, if caches are disabled, do not use this command on arm926ejs.
used on at91 in SPL, to reduce size of SPL.

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-01-19 12:49:26 +01:00
Evgeni Dobrev
9637c4b2dd Add support for Seagate BlackArmor NAS220
Add support for Seagate BlackArmor NAS220

Signed-off-by: Evgeni Dobrev <evgeni@studio-punkt.com>
2015-01-14 11:37:39 -05:00
Fabio Estevam
906d6fe303 mx25: Fix boot hang by avoiding vector relocation
Since commit 3ff46cc42b ("arm: relocate the exception vectors") mx25pdk
hangs like this:

CPU:   Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: WDOG
Board: MX25PDK
I2C:   ready
DRAM:  64 MiB
(hangs)

Add a specific relocate_vectors macro that skips the vector relocation, as the
i.MX25 SoC does not provide RAM at the high vectors address (0xFFFF0000), and
(0x00000000) maps to ROM.

This allows mx25 to boot again.

Acked-By: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-01-08 13:50:17 -05:00
Fabio Estevam
8ed5e4ce0b mx25: Remove empty line after printing the reset cause
Currently there is an unneeded empty line after printing the reset cause:

U-Boot 2015.01-rc4-00080-g0551a93 (Jan 06 2015 - 13:04:19)

CPU:   Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR

Board: MX25PDK
I2C:   ready
DRAM:  64 MiB
MMC:   FSL_SDHC: 0

Remove the extra "\n" when printing the reset cause.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2015-01-08 11:00:45 -05:00
Tom Rini
dee332ffb7 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-11-24 12:02:12 -05:00
Tom Rini
1739564e75 Merge git://git.denx.de/u-boot-dm
Conflicts:
	drivers/serial/serial-uclass.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-11-24 12:01:48 -05:00
Masahiro Yamada
56f31e872e kbuild: use SoC-specific CONFIG to descend into SoC directory
Use "obj-$(CONFIG_FOO) += foo/" where it is possible.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-23 06:49:02 -05:00
Masahiro Yamada
165ecd26f0 kbuild: Descend into SOC directory from CPU directory
Some CPUs of some architectures have SOC directories.
At present, the build system directly descends into SOC directories
from the top Makefile, but it should generally descend into each
directory from its parent directory.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-23 06:49:02 -05:00
Simon Glass
12fe7f7c2a dm: at91: Add platform data for GPIO on at91sam9260-based boards
These boards all have the same GPIO arrangement, so add some common platform
data that can be used by all boards. Remove the configs which are no longer
required.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-11-21 08:09:36 +01:00
Masahiro Yamada
4515992fc7 replace DIV_ROUND with DIV_ROUND_CLOSEST
The Linux-compatible macro DIV_ROUND_CLOSEST is a bit more flexible
and safer than DIV_ROUND.

For example,
  foo = DIV_ROUND_CLOSEST(x, y++)
works expectedly, but
  foo = DIV_ROUND(x, y++)
does not. (y is incremented twice.)

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-11-20 11:28:25 -05:00
Albert ARIBAUD
db544b9662 imx: fix exception vectors relocation in imx27
Commit 3ff46cc4 fixed exception vectors setting in
the general ARM case, by either copying the exception
and indirect vector tables to normal (0x00000000) or
high (0xFFFF0000) vectors address, or setting VBAR to
U-Boot's base if applicable.

i.MX27 SoC is ARM926E-JS, thus has only normal and
high options, but does not provide RAM at 0xFFFF0000
and has only ROM at 0x00000000; it is therefore not
possible to move or change its exception vectors.

Besides, i.MX27 ROM code does provide an indirect
vectors table but at a non-standard address and with
the reset and reserved vectors missing.

Turn the current vector relocation code into a weak
routine called after relocate_code from crt0, and add
strong version for i.MX27.

Series-Cc: Heiko Schocher <hs@denx.de>

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Tested-by: Stefano Babic <sbabic@denx.de>
Tested-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Philippe Reynes <tremyfr@yahoo.fr>
2014-11-20 10:13:54 +01:00
Alexey Ignatov
7a139959d0 ARM: mxs: tools: Add support for boot progress display flag
mkimage -T mxs now support new flag in config file:
DISPLAYPROGRESS - makes boot process print HTLLC characters for each BootROM
instruction.

Signed-off-by: Alexey Ignatov <lexszero@gmail.com>
2014-11-20 10:13:45 +01:00
Heiko Schocher
5abc00d020 arm, spl, at91: add at91sam9260 and at91sam9g45 spl support
add support for using spl code on at91sam9260 and at91sam9g45
based boards.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
[adopt Bo's change in spl.c]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Wolfgang Denk
feb8cf4a1b ARM: MXS: fix Uninitialized variable error
cppcheck reports:

[arch/arm/cpu/arm926ejs/mxs/timer.c:96]: (error) Uninitialized
variable: now

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-11-10 16:25:27 -05:00
Wolfgang Denk
0060517ae0 cppcheck cleanup: fix nullPointer errors
There are a number of places where U-Boot intentionally and legally
accesses physical address 0x0000, for example when installing
exception vectors on systems where these are located in low memory.

Add "cppcheck-suppress nullPointer" comments to silence cppcheck
where this is intentional and legal.

Signed-off-by: Wolfgang Denk <wd@denx.de>
2014-11-07 16:27:07 -05:00
Jeroen Hofstee
09e6e0b7de arm926ejs: cache: use __weak
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-11-04 15:01:04 -05:00
Georges Savoundararadj
2e07c249a6 kconfig: arm: introduce symbol for ARM CPUs
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.

For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.

Also, it removes redundant "string" type in some Kconfig files.

Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-10-29 09:02:09 -04:00
Stefan Roese
678398b19e i2c: designware: Convert driver to multibus/multiadapter framework
In preparation for the SoCFPGA support of the designware I2C driver,
convert this driver to the common CONFIG_SYS_I2C framework.

This patch converts all users of this driver, this is:

- ST spearxxx boards
- AXS101 (ARC700 platform)

I couldn't test this patch on those boards. Only compile tested for all
spear boards. And tested on SoCFPGA.

Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-29 08:56:23 +01:00
Masahiro Yamada
02627356b6 kconfig: add CONFIG_SUPPORT_SPL
CONFIG_SPL should not be enabled for boards that do not have SPL.
CONFIG_SUPPORT_SPL introduced by this commit should be "select"ed
by boards with SPL support and CONFIG_SPL should depend on it.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
2014-10-27 17:54:10 -04:00
Jeroen Hofstee
52422e37bb leds: missing include
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 15:27:35 -04:00
Stefan Roese
1721fe6966 arm: kirkwood: Remove some dead code from cpu.c
All those functions removed with this patch are not accessed at all. So lets
remove them.

Signed-off-by: Stefan Roese <sr@denx.de>
2014-10-23 09:59:21 -04:00
Stefan Roese
d5c5132f87 arm: marvell: Extract kirkwood gpio functions into new common file gpio.c
This makes is possible to use those gpio functions from other MVEBU SoC's as well.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:21 -04:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Stefan Roese
d80cca29fe arm: kirkwood: Move some SoC files into new arch/arm/mvebu-common
By moving some kirkwood files into a Marvell common directory, those files
can be used by other Marvell platforms as well. The name mvebu is taken
from the Linux kernel source tree. It has been chosen there to represent
the SoC's from the Marvell EBU (Engineering Business Unit). Those SoC's
currently are:

Armada 370/375/XP, Dove, mv78xx0, Kirkwood, Orion5x

This will be used by the upcoming Armada XP (MV78460) platform support.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:58:41 -04:00
Marek Vasut
7c604e98c2 arm: mxs: Wait for DRAM to start
Instead of waiting for a fixed period of time and hoping for the best
that the DRAM will start, read back an EMI status register which tells
us exactly when the DRAM started.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Marek Vasut
be0ecdbed5 arm: mxs: Wait when disabling VDDMEM current limiter
According to i.MX23 datasheet Table 32-17, we must wait for the supply
to settle before disabling the current limiter. Indeed, not waiting a
little here causes the system to crash at times.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
2014-09-29 09:02:16 +02:00
Masahiro Yamada
461be2f96e kconfig: remove redundant "string" type in arch and board Kconfigs
Now the types of CONFIG_SYS_{ARCH, CPU, SOC, VENDOR, BOARD, CONFIG_NAME}
are specified in arch/Kconfig.

We can delete the ones in arch and board Kconfig files.

This commit can be easily reproduced by the following command:

find . -name Kconfig -a ! -path ./arch/Kconfig | xargs sed -i -e '
/config[[:space:]]SYS_\(ARCH\|CPU\|SOC\|\VENDOR\|BOARD\|CONFIG_NAME\)/ {
    N
    s/\n[[:space:]]*string//
}
'

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-13 16:43:55 -04:00
Masahiro Yamada
16e16fdde2 nomadik: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Nomadik board select menu to nomadik/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="nomadik").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:22:00 -04:00
Masahiro Yamada
22f2be7a12 orion5x: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Orion5x board select menu to orion5x/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="orion5x").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
3491ba6311 davinci: kconfig: move board select menu and common settings
Becuase the board select menu in arch/arm/Kconfig is too big,
move the Davinci board select menu to davinci/Kconfig.

Move also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="davinci").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
2014-08-30 21:21:59 -04:00
Masahiro Yamada
47539e2317 kirkwood: kconfig: refactor Kconfig and defconfig
Becuase the board select menu in arch/arm/Kconfig is too big,
move the KirkWood board select menu to kirkwood/Kconfig.

Consolidate also common settings (CONFIG_SYS_CPU="arm926ejs" and
CONFIG_SYS_SOC="kirkwood").

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Prafulla Wadasdkar <prafulla@marvell.com>
Cc: Luka Perkov <luka@openwrt.org>
2014-08-30 21:21:21 -04:00
Masahiro Yamada
ad17a81c06 versatile: kconfig: move common settings
Move Versatile-specific settings to versatile/Kconfig.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-08-30 21:19:32 -04:00
Benoît Thébaudeau
eeadd3fe0f arm: Add missing .vectors section to linker scripts
Commit 41623c9 'arm: move exception handling out of start.S files' missed some
linker scripts. Hence, some boards no longer had exception handling linked since
this commit. Restore the original behavior by adding the .vectors section to
these linker scripts.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-08-30 07:46:41 -04:00
DrEagle
3fe3b4fb1c ARM: kirkwood: add mvsdio driver
This patch add Marvell kirkwood MVSDIO/MMC driver
and enable it for Sheevaplugs and OpenRD boards.

Signed-off-by: Gerald Kerma <drEagle@doukki.net>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
2014-08-01 18:44:56 +03:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Khoronzhuk, Ivan
3e01ed00da mtd: nand: davinci: add header file for driver definitions
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:58 -04:00
Thomas Betker
73671dad49 Check run_command() return code properly
run_command() returns 0 for success, 1 for failure. Fix places which
assume that failure is indicated by a negative return code.

Signed-off-by: Thomas Betker <thomas.betker@rohde-schwarz.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Stefan Roese <sr@denx.de>
2014-06-11 16:25:47 -04:00
Tom Rini
90b51c33f3 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-05-30 11:34:39 -04:00
Simon Glass
ae4223f444 Remove unnecessary use of hush header file
Some files include hush.h but don't actually use it. Remove this where
possible.

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-05-29 17:45:31 -04:00
Wu, Josh
cf874c190e ARM: at91sam9m10g45ek: enable mci0 support
Also we enable the mmc command in configuration file.

As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-05-27 00:10:54 +02:00
Albert ARIBAUD
41623c91b0 arm: move exception handling out of start.S files
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.

Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
2014-05-15 16:24:53 +02:00