Move ns_dev[] from header file to C file to avoid compiling warning
when header file is included by others.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
[YS: rewrite commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Add infrastructure for ICID setup and device tree fixup on ARM
platforms. This include basic ICID setup for several devices.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add command "boot_bank X" to switch the boot bank to either 1 or 2.
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
A new defconfig is introduced to support SPL boot from QSPI NOR
flash. This is to support falcon mode for faster booting into
Linux.
Signed-off-by: York Sun <york.sun@nxp.com>
This patch updates the copyright claim for the issues reported by
legal review.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add 'const' (also 'static' in some places) to struct node_info
arrays to save memory footprint.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The m5253evbe board has been marked as orphan since June of 2014 and
should have been dropped a while ago. Do so now.
Signed-off-by: Tom Rini <trini@konsulko.com>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
FRWY-LS1012A belongs to LS1012A family with features 2 1G SGMII PFE
MAC, Micro SD, USB 3.0, DDR, QuadSPI, Audio, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
[yorks: rebase and fix SPDX tag]
[yorks: fix board/freescale/ls1012afrdm/Kconfig]
Reviewed-by: York Sun <york.sun@nxp.com>
PPA firmware and header address may vary depending upon different
boards, configure ppa firmware and header address in board specific
Kconfig.
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Jagdish Gediya <jagdish.gediya@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per updated hardware documentation for
lsch3 based chips like LS2088A, 0.9v support
has been added in possible supported SoC volatges
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
These fsl email addresses are no longer valid and they do not have a
correspondent nxp.com entry.
Remove all invalid fsl email addresses and mark the boards as orphan.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
timur@freescale.com is not a valid email for quite some time, so change
it to Timur's updated email.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Timur Tabi <timur@tabi.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
freescale.com domain is no longer reachable, so switch the
maintainers' emails to nxp.com domain instead.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
mx7dsabresd_secure_defconfig was introduced to allow booting NXP kernel
that has CAAM support and needs to boot in secure mode.
Instead of keeping two different config targets for the same board,
remove mx7dsabresd_secure_defconfig and select
CONFIG_ARMV7_BOOT_SEC_DEFAULT inside mx7dsabresd_defconfig so that
this target could be used to boot both mainline and the vendor kernel.
This makes maintenance task easier and avoid potentially confusion
for the end user.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
This patch enables ethernet support for ls1012a2g5rdb.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables ethernet support for ls1012ardb.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables ethernet support for ls1012afrdm.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch enables ethernet support for ls1012aqds.
Signed-off-by: Calvin Johnson <calvin.johnson@nxp.com>
Signed-off-by: Anjaneyulu Jagarlmudi <anji.jagarlmudi@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.
Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function is required for enabling access to early i2c function
for correct usage of QIXIS_READ and QIXIS_WRITE.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is
now available for SPL build.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4
DDR chips. LS2088ARDB needs to be modified to connect all DQS signals.
Some of them are grounded by default for x8 chips. Tested with RDIMM
MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support
RDIMM. Dropped related timing table.
Signed-off-by: York Sun <york.sun@nxp.com>
Currently only SD, NAND can be secondary boot sources controlled
by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR
can be secondary boot source, while QSPI-NOR is the primary.
Add options in qixis to switch to other boot sources including
ifc and emmc.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enables and compiles VID specific functions for SPL.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When VID feature is supported, check the contents of fuse register
and configure DDR operate at 0.9v.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a board specific API namely board_adjust_vdd which
is required to define the board VDD adjust settings.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Both the "qixis_reset" and esbc_validate" commands can only be used in
full U-Boot so do not build them in SPL. As part of this rework the
qixis code to declare things as static and make use of __weak for
function aliases.
Cc; York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Move some of the code for the "lane_bank" and "cpld" code local
commands so that they are not built for SPL as they can only be
used in full U-Boot. This means we can mark a few functions as
static as well now.
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a CONFIG_SPL_BUILD guard around the code for the "mux" command so
it is not included in SPL.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
QMAP value contains information about QSPI chip-selects. These bits
are used to display information of boot device in checkboard()
function.
QMAP value is stored in most significant 3-bits of 8-bit register
brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using
below logic:
(brdcfg[0] >> 5) & 0x7
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove Board Arch print as its value is always constant '1' and does
not contain any important information to display during boot.
Add print to display Board FPGA version.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot on ARM based platforms.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Currently mmdc_do_dqs_calibration() and mmdc_do_write_level_calibration()
show the same error message, which is confusing for debugging.
Disambiguate the mmdc_do_dqs_calibration() error message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
mx6sabresd board uses the following pins for console:
PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA
,so put it in the same config option as wandboard.
mx6sabreauto board uses the following pins for console:
PAD_KEY_COL0__UART4_TX_DATA
PAD_KEY_ROW0__UART4_RX_DATA
So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option.
The config option for sabreauto can be added later when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Because kernel set WDOG_B mux before pad with the common pinctrl
framwork now and wdog reset will be triggered once set WDOG_B mux
with default pad setting, we set pad setting here to workaround this.
Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
as GPIO mux firstly here to workaround it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Add pfuze dm code, this code could be enabled with CONFIG_DM_PMIC_PFUZE100.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Using changes in this patch we were able to reduce approx 8k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1088a/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1088a/ls1088a.c to keep
board_early_init_f funcations in case of SPL build.
3. Changes in ls1088a_common.h & ls1088ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This is a virtual "board" that uses configuration files and
Kconfig to define the memory layout used by a real board during
the board bring-up process.
It generates an SPL image that can be loaded using imx_usb or
SB_LOADER.exe.
When run, it will generate a set of calibration constants for
use in either or both a DCD configuration file for boards that
use u-boot.imx or struct mx6_mmdc_calibration for boards that
boot via SPL.
In essence, it is a configurable, open-source variant of the
Freescale ddr-stress tool.
https://community.nxp.com/docs/DOC-105652
File mx6memcal_defconfig configures the board for use with
mx6sabresd or mx6qsabreauto.
Signed-off-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Secure boot is not enabled in mx6slevk imximage.cfg, add support for it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Currently only imx6sx-sdb.dtb is loaded, but if revA board is used the
correct dtb is imx6sx-sdb-reva.dtb, so make this possible.
While at it, remove an extra 'mmc dev'.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
NXP development boards based on i.MX6/i.MX7 contain the board
revision information stored in the fuses.
Introduce a common function that can be shared by different boards and
convert mx6sabreauto to use this new mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Linux device tree contains "ethernet" node for all possible
interface supported by SoC i.e. LS1046A.
It is not necessary for a SerDes protocol to support all possible
interface. So disable unavailable "ethernet" node in device tree.
Also, enable FDT_SEQ_MACADDR_FROM_ENV to fetch MAC address
sequentially from environment variables
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
I2C reading for DIP switch setting is not reliable for LS1012ARDB
RevD and later versions. This patch is to add hwconfig support to
enable/disable eSDHC1 manually for these boards. Also drop 'status'
fix-up for eSDHC0 and leave it as it is. It shouldn't always be
fixed up with 'okay'.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add LS1012ARDB RevC/RevC1/RevC2/RevD/RevE information and
detect it when u-boot starts up.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to clean up definitions for I2C IO expanders.
The value 0x10 of __SW_BOOT_EMU is wrong. It should be 0x2.
Fixed it in this patch.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Function fdt_fixup_board_enet() performs fdt fixup. Only return
fdt_status_okay() when both MC is applied and DPL is deployed, else
return fdt_status_fail().
This check is added to LS1088A/LS2080A/LS2088A boards.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The BRDCFG5[SPISDHC] register field of Qixis device is used
to control SPI and SDHC signal routing.
10 = Force SDHC Mode
- SPI_CS[0] is routed to CPLD for SDHC_VS use.
- SPI_CS[1] is unused.
- SPI_CS[2:3] are routed to the TDMRiser slot.
11 = Force eMMC Mode
- SPI_CS[0:3] are routed to the eMMC card.
0X = Auto Mode
- If SDHC_CS_B=0 (SDHC card installed): Use SDHC mode
described above.
- Else SDHC_CS_B=1 (no SDHC card installed): Use eMMC
mode described above.
In default the hardware uses auto mode, but sometimes we need
to use force SDHC mode to support SD card hotplug, or SD sleep
waking up in kernel. This patch is to support force SDHC mode
by hwconfig.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add the secure boot defconfigs for QSPI boot on LS1088ARDB
and LS1088AQDS platforms.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Validates PPA, MC, DPC, Bootscript, DPL and Kernel images in ESBC
phase using esbc_validate command.
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment
Add header address for PPA to be validated during ESBC phase for
LS1088A platform based on LAyerscape Chasis 3.
Moves sec_init prior to ppa_init as for validation of PPA sec must
be initialised before the PPA is initialised.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
IFC-NOR and QSPI-NOR signals are muxed on SoC to save pins
Add fsl_fdt_fixup_flash() to disable IFC-NOR node in dts
if QSPI is enabled and vice-versa
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Most predefined TLB tables don't have memory coherence bit set for
SDRAM. This wasn't an issue before invalidate_dcache_range() function
was enabled. Without the coherence bit, dcache invalidation doesn't
automatically flush the cache. The coherence bit is already set when
dynamic TLB table is used. For some boards with different SPL boot
method, or with legacy fixed setting, this bit needs to be set in
TLB files.
Signed-off-by: York Sun <york.sun@nxp.com>
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.
Signed-off-by: Tom Rini <trini@konsulko.com>
Since DM_USB enabled, no need the usb code in board file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since TX delay is now enabled only in PHY_INTERFACE_MODE_RGMII_ID
PHY_INTERFACE_MODE_RGMII_TXID.
These change where introduced in phy driver in commit 05b29aa0cb
("net: phy: realtek: fix enabling of the TX-delay for RTL8211F").
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:586:5: warning: no previous prototype for ‘board_ehci_hcd_init’ [-Wmissing-prototypes] int board_ehci_hcd_init(int port)
Remove this warning by including <usb/ehci-ci.h>.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:680:5: warning: no previous prototype for ‘board_spi_cs_gpio’ [-Wmissing-prototypes] int board_spi_cs_gpio(unsigned bus, unsigned cs)
Remove this warning by including <asm/mach-imx/spi.h>.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
When building with W=1 errors like the one below is seen:
board/freescale/mx6sabresd/mx6sabresd.c:546:5: warning:
no previous prototype for ‘overwrite_console’
[-Wmissing-prototypes] int overwrite_console(void)
Fix the build warnings by including <input.h>.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
There is no need call setup_display() from SPL code, so move it to
board_init(), which executes only in U-Boot proper.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This board has soldered DDR chips. To reduce the SPL image size,
use static DDR setting instead of dynamic DDR driver.
Signed-off-by: York Sun <york.sun@nxp.com>
The MC boot sequence is contained in mc_env_boot. Update LS1088A
boards to use this function, and hook it to reset_phy so that it's
called late enough, after the ports have been initialized, for
proper DPC / DPL fixup.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As per current implementation, default value of board env is
based on board filename i.e ls2080ardb.
With distro support changes, this env is used to decide upon
kernel dtb which is different for other SoCs (ls2088a, ls2081a)
combination supported with this board.
Add support to modify board env at runtime based on SoC type
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update these macros to use all upper-case to avoid checkpatch
warnings:
ENET_25MHz,
ENET_50MHz,
ENET_125MHz,
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
EC1 and EC2 are RGMII interface on ls1088aqds platform.
This patch add support of RGMII with PHY and MDIO
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <ashish.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds support for RGMII protocol
NXP's LDPAA2 support RGMII protocol. LS1088A is the
first Soc supporting both RGMII and SGMII.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch add support of LS1088AQDS platform.
The LS1088A QorIQTM Development System (QDS) is a high-performance
computing, evaluation, and development platform that supports the
LS1088A QorIQ Architecture processor.
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1088A is an ARMv8 implementation. The LS1088ARDB is an evaluatoin
platform that supports the LS1088A family SoCs. This patch add basic
support of the platform.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@nxp.com>
[YS: Disabled NAND in board header file]
Reviewed-by: York Sun <york.sun@nxp.com>
WIP: disable NAND for LS1088ARDB
Adds header address for PPA to be validated during ESBC phase for
ARCH_LS2088 and QSPI_BOOT. Moves sec_init prior to ppa_init(). It
must be initialized before the PPA.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
[YS: revised commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
CoreLink Cache Coherent Interconnect (CCI) provides full cache
coherency between two clusters of multi-core CPUs and I/O coherency
for devices and I/O masters.
This patch add new config option SYS_FSL_HAS_CCI400 and moves
existing register space definaton of CCI-400 bus to fsl_immap to be
shared. CONFIG_SYS_CCI400_ADDR is replaced with SYS_CCI400_OFFSET
in Kconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
[YS: revised commit message, squashed patches for armv8 and armv7]
Reviewed-by: York Sun <york.sun@nxp.com>
Since the gpr_init() function is common for boards using MX6S, MX6DL, MX6D,
MX6Q and MX6QP processors move it to the soc.c file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
For certain boot types and sbf, for V4 cpu's, an early ddr/sdram init
is required. This patch moves this ddr/sdram early initalization
away from start.S (to be board related).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
At present we have three states for the environment, numbered 0, 1 and 2.
Add an enum to record this to avoid open-coded values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The implementation of function set_pcie_ns_access() uses a wrong
argument. The structure array ns_dev has a member 'ind' which is
initialized by CSU_CSLX_*. It should use the 'ind' directly to
address the PCIe's CSL register (CSL_base + CSU_CSLX_PCIE*).
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
IFC and QSPI are muxed on board. Add fsl_fdt_fixup_flash() to disable
IFC node in dts if QSPI is enabled, or disable QSPI node in dts if
otherwise.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Function enable_layerscape_ns_access() is alreayd called soc-wide.
Remove duplicated calling from individual boards.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[YS: Add commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Function config_board_mux() reads env variable 'hwconfig' which is
only available after relocation for QSPI boot. Move calling
config_board_mux() to misc_init_r().
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Smart voltage translator is removed from LS2080ARDB/LS2088ARDB
RevF boards. It is only used on LS2081ARDB. Programming GPIO
is only required for LS2081ARDB.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Update the default core frequency to 1800MHZ for best performance under
SD boot and eMMC boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The logic of what fdt_get_base_address() will search for and return has
changed. Rework get_phys_ccsrbar_addr_early() to perform the logic that
fdt_get_base_address used to perform.
Fixes: 336a44877a ("fdt: Correct fdt_get_base_address()")
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
nor/qspi boot in case of secure boot. Also enable "secureboot=y"
flag in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") Ethernet does not work on mx6sabreauto.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabreauto design we need some additional configurations,
such as enabling the 125 MHz AR8031 output and setting the TX clock
delay that need to be done in the board file.
This is the equivalent fix from commit 4b6035da48 ("mx6sabresd: Make
Ethernet functional again").
Reported-by: Miquel RAYNAL <miquel.raynal@free-electrons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for Falcon mode and explain in the README the steps to
boot the kernel directly without loading the full U-Boot.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.
I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.
Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:
imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517
By keeping WEIM disabled in U-Boot these kernel issues are gone.
Reported-by: Takashi Matsuzawa <tmatsuzawa@xevo.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <york.sun@nxp.com>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
