Add support for Qualcomm QCS404 SoC based evaluation board.
Features:
- Qualcomm Snapdragon QCS404 SoC
- 1GiB RAM
- 8GiB eMMC, uSD slot
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/qcs404.rst.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Currently this clock driver initializes clocks for UART and eMMC. Along
with this import "qcom,gcc-qcs404.h" header from Linux mainline to
support DT bindings.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Currently this pinctrl driver only supports BLSP UART2 specific pin
configuration.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Add support for 96Boards Dragonboard 845C aka Robotics RB3 development
platform. This board complies with 96Boards Open Platform Specifications.
Features:
- Qualcomm Snapdragon SDA845 SoC
- 4GiB RAM
- 64GiB UFS drive
U-boot is chain loaded by ABL in 64-bit mode as part of boot.img.
For detailed build and boot instructions, refer to
doc/board/qualcomm/sdm845.rst, board: dragonboard845c.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Configure debug UART pins as function: "qup9" rather than being regular
gpios. It fixes a hang seen during pinmux setting.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rather than using magic numbers as clock ids for peripherals import
qcom,gcc-sdm845.h from Linux to be used standard macros for clock ids.
So start using corresponding clk-id macro for debug UART.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
According to u-boot DT recomendation, u-boot specific DT properties belong
to *-uboot.dtsi. Also for starqltechn board (which is the only current
consumer of sdm845.dtsi), the properties are already included in
starqltechn-uboot.dtsi, so remove corresponding redundant properties.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Currently there is a mismatch among DT node overrides in starqltechn
board DTS file and the actual DT nodes in the sdm845.dtsi. So fix that
to align with DT nodes in sdm845.dtsi.
Signed-off-by: Sumit Garg <sumit.garg@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mp-verdin-wifi-dev.dtb rather than the previous imx8mp-verdin.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warnings:
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@0:pwms: property size (12) too small for cell size 3
w+arch/arm/dts/imx8mp-rsb3720-a1.dtb: Warning (pwms_property):
/lvds_backlight@1:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Verdin Development (carrier) board (e.g.
imx8mm-verdin-wifi-dev.dtb rather than the previous imx8mm-verdin.dtb).
Please further note that the PMIC node name got changed from a pmic
label to pmic@25 which required adjustment in resp. board SPL file
board/toradex/verdin-imx8mm/spl.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warnings:
w+arch/arm/dts/imx8mm-kontron-n801x-s-lvds.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the pinctrl_pmic reference which does not
exist in the Linux upistream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/imx8mm-venice-gw700x-u-boot.dtsi:26.1-14 Label or
path pinctrl_pmic not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
vf610-colibri-eval-v3.dtb rather than the previous vf610-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step rename the included SoC dtsi from vf.dtsi to
vf610.dtsi as this is how it is named in Linux upstream.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx7d-colibri-eval-v3.dtb rather than the previous
imx7-colibri-rawnand.dtb and imx7d-colibri-emmc-eval-v3.dtb rather than
the previous imx7-colibri-emmc.dtb).
Please further note that the PMIC node name got changed from rn5t567@33
to pmic@33 which required adjustment in resp. board file
board/toradex/colibri_imx7/colibri_imx7.c.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the epdc reference which does not exist in
the Linux upstream device tree and rename the qspi1 reference to qspi as
this is how it is named in the Linux upstream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/.imx7d-sdb-qspi.dtb.pre.tmp:10.1-6 Label or path
epdc not found
+Error: arch/arm/dts/.imx7d-sdb-qspi.dtb.pre.tmp:29.1-7 Label or path
qspi1 not found
+Error: arch/arm/dts/imx7d-sdb-qspi-u-boot.dtsi:6.1-7 Label or path
qspi1 not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step rename the qspi1 reference to qspi as this is how
it is named in the Linux upstream device tree.
This avoids the following error once synchronised:
+Error: arch/arm/dts/.imx7-cm.dtb.pre.tmp:96.1-7 Label or path qspi1 not
found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux v5.19-rc5.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device trees we are now using the
regular ones for the Colibri Evaluation (carrier) board V3 (e.g.
imx6ull-colibri-eval-v3.dtb rather than the previous imx6ull-colibri.dtb
and imx6ull-colibri-emmc-eval-v3.dtb rather than the previous
imx6ull-colibri-emmc.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step remove the qspi node with its flash0 label as this
is already in the Linux upstream device tree.
This avoids the following error once synchronised:
+arch/arm/dts/imx6ul-14x14-evk.dtb: ERROR (duplicate_label):
/soc/bus@2100000/spi@21e0000/n25q256a@0: Duplicate label 'flash0' on
/soc/bus@2100000/spi@21e0000/n25q256a@0 and
/soc/bus@2100000/spi@21e0000/flash@0
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next next-20220708.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Colibri Evaluation (carrier) board V3 (e.g.
imx6dl-colibri-eval-v3.dtb rather than the previous imx6-colibri.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Synchronise device tree with linux-next 20220706.
Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Apalis Evaluation (carrier) board (e.g.
imx6q-apalis-eval.dtb rather than the previous imx6-apalis.dtb).
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
As a preparatory step make sure to refer to absolute node paths where
labels were removed in Linux upstream.
This avoids the following error once synchronised:
+Error: arch/arm/dts/imx6q-tbs2910-u-boot.dtsi:3.1-7 Label or path aips1
not found
+Error: arch/arm/dts/imx6q-tbs2910-u-boot.dtsi:11.1-5 Label or path soc
not found
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Fix the following build-time pwms property warning:
w+arch/arm/dts/imx6dl-brppt2.dtb: Warning (pwms_property):
/backlight:pwms: property size (12) too small for cell size 3
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
On AM62x devices, main ESM error event outputs can be routed to
MCU ESM as inputs. So, two ESM device nodes are expected in the
device tree : one for main ESM and another one for MCU ESM.
MCU ESM error output can trigger the reset logic to reset
the device when CTRLMMR_MCU_RST_CTRL:MCU_ESM_ERROR_RESET_EN_Z is
set to '0'.
Signed-off-by: Julien Panis <jpanis@baylibre.com>
Apple's M2 SoC very similar to the M1 and can use the same memory map.
The keyboard/trackpad on the MacBook Pro (13-inch, M2, 2022) uses
"dockchannel" as transport instead of SPI and needs a new driver.
USB, NVMe, uart, framebuffer and watchdog are working with the existing
drivers.
Signed-off-by: Janne Grunau <j@jannau.net>
Reviewed-by: Mark Kettenis <kettenis@openbsd.org>
The macro `CONFIG_SYS_UBOOT_BASE` is used by SPL loaders `"NOR"` and
`"XIP"` to determine the base address of u-boot.
For `"NOR"` on i.MX8MM it is the base address of QSPI0 plus the offset
of the flattened image tree blob.
Although `QSPI0_AMBA_BASE` is used to define CONFIG_SYS_UBOOT_BASE in
multiple board header files for i.MX8MM, it is not specified.
Specify offset of flattened image tree blob (needs to be set to same
value as specified in 'binman' node), base address of QSPI0 and size of
FlexSPI configuration block.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Add definition for FSPI configuration block and subsequently new offsets for
u-boot-spl and u-boot-itb for CONFIG_FSPI_HEADER option.
Signed-off-by: Mamta Shukla <mamta.shukla@leica-geosystems.com>
Signed-off-by: Thomas Haemmerle <thomas.haemmerle@leica-geosystems.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Simplify the use of the ROM API by using the wrappers that take care
of saving/restoring gd and computing the xor value. This makes the
generated code smaller and the C code easier to read.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The ROM API is thoroughly undocumented, but apparently passing the xor
of the real arguments as an extra argument is required [1]. Also, we
need to do the "save gd/restore gd" dance. These are both error-prone,
and lead to a lot of code duplication.
Since both imx8m[np] and imx8ulp SOCs have this, add a separate
translation unit which is included precisely when the new
CONFIG_IMX8_ROMAPI symbol is set, which provide convenience wrappers
that take care of computing the xor value as well as doing the gd
dance, and that thus have a more intuitive API. Subsequent patches
will make use of these to reduce boilerplate.
[1] One wonders, for example, if the check is only applied to the
lower 32 bits, or if we're implicitly relying on all 64-bit pointer
values we're passing effectively have 0 in the upper 32 bits.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This exposes the struct rom_api, the g_rom_api variable declaration
and the associated #defines to slightly fewer boards: namely, those
IMX8M which are not IMX8MN or IMX8MP. But the latter two are the only
IMX8M* ones where the g_rom_api variable is defined (in imx8m/soc.c),
so that should be fine.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
In order not to repeat the IMX8MN || IMX8MP || IMX8ULP logic in
multiple places where we need to know if the SOC exposes the ROM API,
add a "def_bool y" Kconfig symbol.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The TI DP83867 phy has been replaced with the MaxLinear GPY111 phy
due to part availability. Add support for it:
- increase post-reset time to 300ms per datasheet
- leave tx-delay/rx-delay undefined in dt defaulting to 2.0ns
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
CONFIG_ETHPRIME can be set to DT node name or alias which refers to DT
node. Define ethernet aliases and set ETHPRIME to eth2 which refers to WAN
ethernet port. This removes hardcoded DT node name from U-Boot
configuration file.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Change detection of platform/cpu from runtime to compile time via config
define. This completely eliminates compiling code which is not going to run
on selected platform. Code which parses and prints device / revision id
still reads device id from MVEBU_REG_PCIE_DEVID register, but only once.
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Fix diacritics in some instances of my name and change my e-mail address
to kabel@kernel.org.
Add corresponding .mailmap entries.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Methode eDPU is an Armada 3720 power board based on the Methode uDPU.
They feature the same CPU, RAM, and storage as well as the form factor.
However, eDPU only has one SFP slot plus a copper G.hn port which does not
work under U-boot.
In order to reduce duplication, split the uDPU DTS into a common one.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
