With the newly added testing of more than one device, we get:
=> ut dm pci_swapcase
Test: dm_test_pci_swapcase: pci.c
test/dm/pci.c:88, dm_test_pci_swapcase(): "tHIS IS A tESt" = ptr:
Expected "tHIS IS A tESt", got "this is a test"
Test: dm_test_pci_swapcase: pci.c (flat tree)
test/dm/pci.c:88, dm_test_pci_swapcase(): "tHIS IS A tESt" = ptr:
Expected "tHIS IS A tESt", got "this is a test"
Failures: 2
The failure only happens on the 2nd swap_case device on the PCI bus.
The case passes on the 1st device.
It turns out the swap_case driver does not emulate bit#0 in BAR
registers as a read-only bit. This corrects the implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
At present the code overruns the bar[] array. Fix this.
At the same time, drop the leading / from the "/spl" path so that we can
run U-Boot SPL with:
spl/u-boot-spl
rather than requiring:
/path/to/spl/u-boot-spl
Reported-by: Coverity (CID: 131199)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since commit 0e373c0ade ("spl: add SPL_RESET_SUPPORT"),
reset is supported in SPL, enable this flag for STM32F SoCs family.
This allows to remove a specific case in RCC mfd driver.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add support of fuse command (read/write/program/sense)
on bank 0 to access to BSEC SAFMEM (4096 OTP bits).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested By: Bruno Herrera <bruherrera@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch added Kconfig support for CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET
and enabled it in respective defconfig.
Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
i.MX8M OCOTP follow same flow as i.MX6Q, but it has 64 banks
and each bank 4 words.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
U-Boot on QEMU does not build ACPI table by ourself, instead it uses
the prebuilt ACPI table via the qfw interface. This implements the
qfw version of acpi_get_rsdp_addr() for setup_zimage().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
On i.MX7ULP, the fuse words (except bank 0 and 1) only supports to
write once, because they use ECC mode. Multiple writes may damage
the ECC value and cause a wrong fuse value decoded when reading.
This patch adds a checking before the fuse word programming, only
can write when the word value is 0.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch adds changes necessary to move functionality present in
PowerPC folders with ARM architectures that have DPAA1 QBMan hardware
- Create new board/freescale/common/fsl_portals.c to house shared
device tree fixups for DPAA1 devices with ARM and PowerPC cores
- Add new header file to top includes directory to allow files in
both architectures to grab the function prototypes
- Port inhibit_portals() from PowerPC to ARM. This function is used in
setup to disable interrupts on all QMan and BMan portals. It is
needed because the interrupts are enabled by default for all portals
including unused/uninitialised portals. When the kernel attempts to
go to deep sleep the unused portals prevent it from doing so
Signed-off-by: Ahmed Mansour <ahmed.mansour@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Like STM32H7, now STM32F4/F7 clock drivers are binded by
MFD stm32_rcc driver.
This also allows to add reset support to STM32F4/F7 SoCs family.
As Reset driver is not part of SPL supported drivers, don't bind it
in case of SPL to avoid that stm32_rcc_bind() returns an error.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch adds the support of reset and clock control
block (rcc) found on STM32 SoCs.
This driver is similar to a MFD linux driver.
This driver supports currently STM32H7 only.
STM32F4 and STM32F7 will be migrated to this rcc MFD driver
in the future to uniformize all STM32 SoCs already upstreamed.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the dev_read_addr_ptr function available, we can change the
efuse driver to use it (and eliminate the explicit type-cast).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the new compatible "atmel,24mac402" to accommodate AT24MAC402.
The AT24MAC402 is a 2K Serial EEPROM and the 2-Kbit memory array
is internally organized as 16 pages of 16 bytes of EEPROM each.
The 48-bit EUI address in the AT24MAC402 are located in the extended
memory block.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add the new compatible "microchip,24aa02e48" to accommodate 24AA02E48,
the 24AA02E48 is a 2K I2C Serial EEPROM with pre-programmed globally
unique, 48-bit node address, and 8-byte page size.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Add a convenience macro to iterate over subnodes of a node. Make use of
this where appropriate in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is an SPL-variant of the I2C_EEPROM option to enable
the driver for generic I2C-attached EEPROMs for SPL.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the following options to drivers/misc/Kconfig:
SYS_I2C_EEPROM_ADDR
SYS_I2C_EEPROM_BUS
SYS_EEPROM_SIZE
SYS_EEPROM_PAGE_WRITE_BITS
SYS_EEPROM_PAGE_WRITE_DELAY_MS
SYS_I2C_EEPROM_ADDR_LEN
SYS_I2C_EEPROM_ADDR_OVERFLOW
This does not migrate any boards, but provides a foundations for
those who want/need these options
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate uniphier]
Signed-off-by: Tom Rini <trini@konsulko.com>
This changes the rockchip-efuse driver to use dev_read_addr instead of
devfdt_get_addr.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This module can be found on the Turris Omnia board connected
via the I2C interface.
Among some cryptographic functions, the chip has a 512 bit
One Time Programmable memory, 88 byte configuration memory
and 512 byte general purpose memory.
The Turris Omnia stores serial number and device MAC address in
the OTP memory.
This commit adds basic support for reading the EEPROM and also
exposes the chips Random Number Generator.
The driver is based on code by
Josh Datko, Cryptotronix, jbd@cryptotronix.com
and also
Tomas Hlavacek, CZ.NIC, tomas.hlavacek@nic.cz
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 drivers/misc/atsha204a-i2c.c
create mode 100644 include/atsha204a-i2c.h
Signed-off-by: Stefan Roese <sr@denx.de>
This function returns the pointer to the value of a node property.
The current name ofnode_read_prop() is confusing. Follow the naming
of_get_property() from Linux.
The return type (const u32 *) is wrong. DT property values can be
strings as well as integers. This is why of_get_property/fdt_getprop
returns an opaque pointer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
These are only used in drivers/mis/i2c_eeprom.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
This adds a simple driver for reading the efuse block of the RK3399.
It should be easy enough to add drivers for other devices (e.g. the
RK3328, RK3368, etc.) by passing the device details via driver_data.
Unlike the kernel driver (using the nvmem subsystem), we don't expose
the efuse as multiple named cells, but rather as a linear memory that
can be read using misc_read(...).
The primary use case (as of today) is the generation of a 'serial#'
(and a 'cpuid#') environment variable for the RK3399-Q7 (Puma)
system-on-module.
Note that this adds a debug-only (i.e. only if DEBUG is defined)
command 'rk3399_dump_efuses' that dumps the efuse block's content.
N.B.: The name 'rk3399_dump_efuses' was intentionally chosen to
include a SoC-name (together with a comment in the function) to
remind whoever adds support for additional SoCs that this
function currently makes assumptions regarding the size of the
fuse-box based on the RK3399. The hope is that the function is
adjusted to reflect any changes resulting from generalising the
driver for multiple SoCs and is then renamed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert this driver to support the live device tree and remove the old
fdtdec support.
The keyboard is not yet converted.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust this function to us an ofnode instead of an offset, so it can be
used with livetree. This involves updating all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is only used by one board and always set to 0x51. Drop this option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This converts the following to Kconfig:
CONFIG_DS4510
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option enables a command in the driver. But the functions defined by
the driver are not called anywhere else in U-Boot. So it does not seem
useful to have this driver without its commands.
Drop this option, move the header file out of the common include/
directory and make all the function static.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option is only used in one driver and is not enabled by any board. It
does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option is only used in one driver and is not enabled by any board. It
does not seem worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This option is only used in one driver and two boards. It does not seem
worth having the ability to remove this part of the support.
Drop the option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update the mxc_ocotp driver to support i.MX7ULP.
The read/write sequence has some changes due to
PDN and OUT_STATUS registers added and TIME register is
removed. Also update the bank size and number.
Add is_mx7ulp macro in sys_proto.h
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by : Stefano Babic <sbabic@denx.de>
Add support for version 3 of the ec protocol. It basically works by
stitching some additional header in front (special command code),
and having a result and packet_length stitched on for the reply.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Tested on snow:
Tested-by: Simon Glass <sjg@chromium.org>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Replace dm_i2c_write() / dm_i2c_read() with transaction using
struct i2c_msg[2] in order to allow for i2c controller to detect
write/read cycle to emit a repeated start condition.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Tested on snow:
Tested-by: Simon Glass <sjg@chromium.org>
We should use unsigned long rather than u32 for addresses. Update this so
that the table-generation code builds correctly on 64-bit machines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move all of the status LED feature to drivers/led/Kconfig.
The LED status definitions were moved from the board configuration
files to the defconfig files.
TBD: Move all of the definitions in the include/status_led.h to the
relevant board's defconfig files.
Tested boards: CL-SOM-AM57x, CM-T335
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Add the i.MX6SLL support to OCOTP driver.
The i.MX6SLL reuses the i.MX6ULL fuse, bank 7 and bank8 have 4 words
each, and there is a hole between bank 5 and bank 6.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The cros_ec_decode_region() function is only used in combination
with the crosec cmds. Move the function to the correct place.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
This commit fixes an issue where data is written to an
invalid memory location.
The issue has been introduced in commit
(88364387 cros: add cros_ec_driver)
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add command to print out the flash info as reported by the
ec. The data read back includes size, write block size,
erase block size.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Add support for reading back flash parameters as reported by
the ec.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Boards where ECs that use a I2C port != 0 specify this in the
devicetree file via the google,remote-bus property.
Previously this was ignored and hardcoded to port 0.
Signed-off-by: Moritz Fischer <moritz.fischer@ettus.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: u-boot@lists.denx.de
Acked-by: Simon Glass <sjg@chromium.org>
Update the API's for transition of Security Monitor states. Instead
of providing both initial and final states for transition, just
provide final state for transition as Security Monitor driver will
take care of it internally.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
[York Sun: Reformatted commit message slightly]
Reviewed-by: York Sun <york.sun@nxp.com>
i.MX6ULL has two 128 bits fuse banks, bank 7 and bank 8,
while other banks use 256 bits. So we have to adjust the
word and bank index when accessing the bank 8.
When in command line `fuse read 8 0 1`, you can image
`fuse read 7 4 1` in the ocotp driver implementation for 6ULL.
When programming, we use word index, so need to fix bank7/8 programming
for i.mx6ull.
For example: fuse prog 8 3 1; The word index is (8 << 3 | 3) --> 67.
But actully it should be (7 << 3 | 7) ---> 63.
So fix it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
The Tegra CAR (Clock And Reset) module provides control of most clocks
and reset signals within the Tegra SoC. This change implements a driver
for this module. However, since the module implements multiple kinds of
services (clocks, resets, perhaps more), all this driver does is bind
various sub-devices, which in turn provide the real services. This driver
is essentially an "MFD" (Multi-Function Device) in Linux kernel speak.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
This simple driver provides some functions to control some of the
integrated devices. The watchdog is enabled per default. This driver
adds a function to disable the watchdog. Also the internal legacy
UART (io address 0x3f8/0x2f8) is enabled per default.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
The Tegra BPMP (Boot and Power Management Processor) is a separate
auxiliary CPU embedded into Tegra to perform power management work, and
controls related features such as clocks, resets, power domains, PMIC I2C
bus, etc. This driver provides the core low-level communication path by
which feature-specific drivers (such as clock) can make requests to the
BPMP. This driver is similar to an MFD driver in the Linux kernel. It is
unconditionally selected by CONFIG_TEGRA186 since virtually any Tegra186
build of U-Boot will need the feature.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The call op requests that the callee pass a message to the underlying HW
or device, wait for a response, and then pass back the response error code
and message to the callee. It is useful for drivers that represent some
kind of messaging or IPC channel to a remote device.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Create drivers/sysreset and move sysreset-uclass and all sysreset
drivers there.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Quite a few places have a bind() method which just calls dm_scan_fdt_dev().
We may as well call dm_scan_fdt_dev() directly. Update the code to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch implements the reading functionality for the generic I2C
EEPROM driver, which was just a non-functional stub until now.
Since the page size will be of importance for the writing support, we
add suitable members to the private data structure to keep track of it.
Compatibility strings for a range of at24c* chips are added.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add a driver which uses of-platdata to obtain its platform data. This can
be used to test the feature in sandbox. It displays the contents of its
platform data.
Signed-off-by: Simon Glass <sjg@chromium.org>
The cros-ec keyboard is always a child of the cros-ec node. Rather than
searching the device tree, looking at the children. Remove the compat string
which is now unused.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current reset API implements a method to reset the entire system.
In the near future, I'd like to introduce code that implements the device
tree reset bindings; i.e. the equivalent of the Linux kernel's reset API.
This controls resets to individual HW blocks or external chips with reset
signals. It doesn't make sense to merge the two APIs into one since they
have different semantic purposes. Resolve the naming conflict by renaming
the existing reset API to sysreset instead, so the new reset API can be
called just reset.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Loading ACPI table from QEMU's fw_cfg interface is not x86 specific
(ARM64 may also make use of it). So move the code to common place.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Make file names consistent with CONFIG_QFW and CONFIG_CMD_QFW
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The original implementation of qfw includes several x86 specific
operations, like directly calling outb/inb and using some inline
assembly code which prevents it being ported to other architectures.
This patch adds callback functions and moves those to arch/x86/
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch splits qfw command interface and qfw core function into two
files, and introduces a new Kconfig option (CONFIG_QFW) for qfw core.
Now when qfw command interface is enabled, it will automatically select
qfw core. This patch also makes the ACPI table generation select
CONFIG_QFW.
Signed-off-by: Miao Yan <yanmiaobest@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There are already two FIT options in Kconfig but the CONFIG options are
still in the header files. We need to do a proper move to fix this.
Move these options to Kconfig and tidy up board configuration:
CONFIG_FIT
CONFIG_OF_BOARD_SETUP
CONFIG_OF_SYSTEM_SETUP
CONFIG_FIT_SIGNATURE
CONFIG_FIT_BEST_MATCH
CONFIG_FIT_VERBOSE
CONFIG_OF_STDOUT_VIA_ALIAS
CONFIG_RSA
Unfortunately the first one is a little complicated. We need to make sure
this option is not enabled in SPL by this change. Also this option is
enabled automatically in the host builds by defining CONFIG_FIT in the
image.h file. To solve this, add a new IMAGE_USE_FIT #define which can
be used in files that are built on the host but must also build for U-Boot
and SPL.
Note: Masahiro's moveconfig.py script is amazing.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add microblaze change, various configs/ re-applies]
Signed-off-by: Tom Rini <trini@konsulko.com>
The SMSC SIO1007 superio chipset integrates two ns16550 compatible
serial ports for legacy applications, 16 GPIO pins and some other
functionalities like power management.
This adds a simple driver to enable serial port and handle GPIO.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some devices need special sequences to be used when starting up. Add a
uclass for this. Drivers can be added to provide specific features as
needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
The console includes a global variable and several functions that are only
used by a small subset of U-Boot files. Before adding more functions, move
the definitions into their own header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Building with gcc-5.2 raises this warning:
drivers/misc/cros_ec_sandbox.c: In function cros_ec_sandbox_packet:
drivers/misc/cros_ec_sandbox.c:483:5: warning: len may be used uninitialized in this function [-Wmaybe-uninitialized]
if (len < 0)
^
If the function process_cmd() is called with
req_hdr->command == EC_CMD_ENTERING_MODE, the value of len will be
returned uninitialized.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In preparation for converting the cros_ec keyboard driver to driver model,
adjust the cros_ec functions it will use to use a normal struct udevice.
Signed-off-by: Simon Glass <sjg@chromium.org>
Change ioremap() to map_physmem(), as it is more used in u-boot.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For current U-Boot to initialize status LEDs via status_led_init(), it
is required to have both CONFIG_STATUS_LED and STATUS_LED_BOOT defined.
This may be a particular concern with GPIO LEDs, where __led_init() is
required to correctly set up the GPIO (gpio_request and
gpio_direction_output). Without STATUS_LED_BOOT the initialization isn't
called, which could leave the user with a non-functional "led" command -
due to the fact that the LED routines in gpio_led.c use gpio_set_value()
just fine, but the GPIO never got set up properly in the first place.
I think having CONFIG_STATUS_LED is sufficient to justify a
corresponding call to status_led_init(), even with no STATUS_LED_BOOT
defined. To do so, common/board_r.c needs call that routine, so it now
is exposed via status_led.h.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
[trini: Add dummy __led_init to pca9551_led.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
For boards that support LEDs driven via GPIO (CONFIG_GPIO_LED),
it may be useful to have some generic stubs (wrapper functions)
for the "colored" LEDs.
This allows defining STATUS_LED_* values directly to GPIO numbers,
e.g.: #define STATUS_LED_GREEN 248 /* = PH24 */
To keep those optional, it's probably best to introduce an additional
configuration setting. I've chosen CONFIG_GPIO_LED_STUBS for that.
Placing the code in drivers/misc/gpio_led.c also ensures that it
automatically depends on CONFIG_GPIO_LED too.
Signed-off-by: Bernhard Nortmann <bernhard.nortmann@web.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with other driver model data access
functions. Rename it and fix up all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Convert altera sysid to driver model with misc uclass.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Implement a Miscellaneous uclass with generic read or
write operations. This class is used only for those
do not fit other more general classes.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
Currently 'reset' only works with the test device tree. When run without a
device tree, or with the normal device tree, the following error is
displayed:
Reset not supported on this platform
Fix the driver and the standard device tree to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Should use FSL_SEC_MON, not CONFIG_FSL_SEC_MON as Kconfig entry.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
There is a hole in shadow registers address map of size 0x100
between bank 5 and bank 6 on iMX6QP, iMX6DQ, iMX6SDL, iMX6SX and iMX6UL.
Bank 5 ends at 0x6F0 and Bank 6 starts at 0x800. When reading the fuses,
we should account for this hole in address space.
Similar hole exists between bank 14 and bank 15 of size
0x80 on iMX6QP, iMX6DQ, iMX6SDL and iMX6SX.
Note: iMX6SL has only 0-7 banks and there is no hole.
Note: iMX6UL doesn't have this one.
When reading, we use register offset, so need to account for holes
to get the correct address.
When writing, we use bank/word index, there is no need to account
for holes, always use bank/word index from fuse map.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
* Ocotp of i.MX7D has different operation rule.
This patch is to add support for i.MX7D ocotp.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
When the original HBUS divider value is retrieved in mxs_ocotp_scale_hclk()
for the purpose or restoring it back later, the value is not shifted by the
HBUS divider offset in that register. This is not a problem, since the shift
is zero on all MXS hardware. Add the shift anyway, for completeness and in
case FSL ever decides to re-use this driver on future designs.
Signed-off-by: Chris Smith <chris@zxdesign.info>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
DEVDISRn registers provides a mechanism for gating clocks of IP blocks
that are not used. Here we implement hwconfig option to allow users
to disable unused peripherals on the board.
For ex. If eSDHC/qDMA/eDMA are unused and with disabled status in dts,
User can enable CONFIG_FSL_DEVICE_DISABLE and set "devdis:esdhc,qdma,edma"
in hwconfig, thus ESDHC controller & eDMA/qDMA will be clock gated to
save more power.
Signed-off-by: Zhuoyu Zhang <Zhuoyu.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Append "debug server FW" in error message to make more informative.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add an api to enable and configure the integrated keyboard controller
on SMSC LPC47m superio chipset. It also adds several macros to help
future extension.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add a driver to support the special LDO access used by spring. This is a
custom method in the cros_ec protocol - it does not use an I2C
pass-through.
There are two implementation choices:
1. Write a special LDO driver which can talk across the EC. Duplicate all
the logic from TPS65090 for retrying when the LDO fails to come up.
2. Write a special I2C bus driver which pretends to be a TPS65090 and
transfers reads and writes using the LDO message.
Either is distasteful. The latter method is chosen since it results in less
code duplication and a fairly simple (30-line) implementation of the core
logic.
The crosec 'ldo' subcommand could be removed (since i2c md/mw will work
instead) but is retained as a convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Only 2 frequencies are supported. The current driver implementation does
not always use the 2 last configured blink frequencies. This patch
fixes this problem. So that the last two entered frequencies are
active.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
Move sandbox over to use the reset uclass for reset, instead of a direct
call to do_reset(). This allows us to add tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add drivers for sandbox. One can only perform a warm reset (which does
nothing). The other can perform a cold reset or a power reset (the
latter will quit U-Boot). These can be used for testing the reset uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new reset_walk_halt() function to cause a reset and then halt on
failure. The reset_walk() function returns an error code.
This is needed for testing since otherwise U-Boot will halt in the middle
of a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is common for system reset to be available at multiple levels in modern
hardware. For example, an SoC may provide a reset option, and a board may
provide its own reset for reasons of security or thoroughness. It is useful
to be able to model this hardware without hard-coding the behaviour in the
SoC or board. Also there is a distinction sometimes between resetting just
the CPU (leaving GPIO state alone) and resetting all the PMICs, just cutting
power.
To achieve this, add a simple system reset uclass. It allows multiple devices
to provide reset functionality and provides a way to walk through them,
requesting a particular reset type until is it provided.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch fixes the DDR hide logic for LS2085a, correcting the way
the Debug Server FW and MC FW images are placed on the top of system
DDR and how the rest of the system DDR space is made visibile to Linux.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma at freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar at freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds a driver for the PCA9551 LED controller.
Originated-by: Timo Herbrecher <t.herbrecher@gateware.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Cc: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
With several chips using the SPI protocol it seems better to put the single
duplex functionality in the EC rather than the SPI driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
For starting a Linux console on the superio serial port under
interrupt mode, the IRQ number must be configured.
Signed-off-by: Jian Luo <jian.luo4@boschrexroth.de>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds NAND boot support for LS2085AQDS, using SPL framework.
Details of forming NAND image can be found in README.
Signed-off-by: Scott Wood <scottwood@freescale.com>
[York Sun: Remove +S from defconfig after commit 252ed872]
Signed-off-by: York Sun <yorksun@freescale.com>
For fsl-lsch3, IFC is binded with address within 32-bit at fist.
After u-boot relocates to DDR, CS1, CS3 can be binded to higher
address to support large space.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This patch extends the U-Boot "led" command to support automatic blinking
by setting a blink frequency in milliseconds. Additionally the number of
supported LEDs is increased to 6 (0...5).
This will be used by the PCA9551 LED driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
The Debug Server driver is responsible for loading the Debug
server FW on the Service Processor (Cortex-A5 core) on LS2085A like
SoCs and then polling for the successful initialization of the same.
TOP MEM HIDE is adjusted to ensure the space required by Debug Server
FW is accounted for. MC uses the DDR area which is calculated as:
MC DDR region start = Top of DDR - area reserved by Debug Server FW
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The U-Boot device trees are slightly different in a few places. Adjust them
to remove most of the differences. Note that U-Boot does not support the
concept of interrupts as distinct from GPIOs, so this difference remains.
For sandbox, use the same keyboard file as for ARM boards and drop the
host emulation bus which seems redundant.
Signed-off-by: Simon Glass <sjg@chromium.org>
This command is supposed to reinit the device. At present with driver
model is does nothing. Implement this feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
This device sits on the sandbox PCI bus and provides a case-swapping
service for sandbox. It illustrates the use of both PCI I/O and PCI
memory accesses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Security Monitor is the SOC’s central reporting point for
security-relevant events such as the success or failure of boot
software validation and the detection of potential security compromises.
The API's for transition of Security states have been added
which will be used in case of SECURE BOOT.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since both I2C and SPI are converted to Kconfig, we can convert cros_ec
to Kconfig for these buses.
LPC will need to wait until driver mode PCI is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
I2C is now deprecated on ARM platforms and there are no devices that use it
with the v3 protocol. We can't require v3 support if we want to support I2C.
Adjust the error handling to suit.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
drivers/misc/i2c_eeprom.c fails to build unless CONFIG_FIT_SIGNATURE
is defined.
CC drivers/misc/i2c_eeprom.o
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:15:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:15:10: note: each undeclared identifier
is reported only once for each function it appears in
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_write':
drivers/misc/i2c_eeprom.c:21:10: error: 'ENODEV' undeclared
(first use in this function)
drivers/misc/i2c_eeprom.c:22:1: warning: control reaches end of
non-void function [-Wreturn-type]
drivers/misc/i2c_eeprom.c: In function 'i2c_eeprom_read':
drivers/misc/i2c_eeprom.c:16:1: warning: control reaches end of
non-void function [-Wreturn-type]
make[2]: *** [drivers/misc/i2c_eeprom.o] Error 1
make[1]: *** [drivers/misc] Error 2
make: *** [drivers] Error 2
By the way, Sandbox (enabling CONFIG_FIT_SIGNATURE) is luckily
working depending on it.
Sandbox includes include/asm-generic/errno.h
from include/errno.h
from include/u-boot/rsa-checksum.h
from include/image.h
from include/common.h
from drivers/misc/i2c_eeprom.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There seem to be a few EEPROM drivers around - perhaps we should have a
single standard one? This simple driver is used for sandbox testing, but
could be pressed into more active service.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To enable testing of I2C, add a simple I2C EEPROM simulator for sandbox.
It supports reading and writing from a small data store.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Leave the OCOTP turned on, so that we subsequent access do not fail.
After enabling the thermal driver on a mx6sxsabresd board:
U-Boot 2015.01-rc1-18267-g99d4189-dirty (Nov 24 2014 - 12:59:01)
CPU: Freescale i.MX6SX rev1.0 at 792 MHz
CPU: Temperature 48 C
Reset cause: POR
Board: MX6SX SABRE SDB
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 2
00:01.0 - 16c3:abcd - Bridge device
01:00.0 - 8086:08b1 - Network controller
In: serial
Out: serial
Err: serial
Net:
(hang)
As the thermal driver accesses the ocotp registers, its clock will be disabled
afterwards.
Then when the MAC address is read (also from ocotp registers) it will cause a
hang.
Do not disable the ocotp clock to prevent this problem.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau.dev@gmail.com>
A previous operation may have set the error flag, which must be cleared
before a new write operation can be issued.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The write operation may fail when trying to write to a locked area. In
this case the ERROR bit is set in the CTRL register. Check for that
condition and return an error.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
The code may goto 'fail' upon error with 'ret' variable set to an error
code, but this variable was being overwritten by a final preparation
function to restore the HCLK, so success was (in general) returned even
after an error was hit previously.
With this change, the function may now return success even if the final
preparation function fails, but it's probably enough to print a message
because (if successful) the real programming of the fuses has already
completed.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
This fixes this cppcheck report:
[drivers/misc/cros_ec.c:704]: (error) Uninitialized variable: req
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Wolfgang Denk <wd@denx.de>
The Linux-compatible macro DIV_ROUND_CLOSEST is a bit more flexible
and safer than DIV_ROUND.
For example,
foo = DIV_ROUND_CLOSEST(x, y++)
works expectedly, but
foo = DIV_ROUND(x, y++)
does not. (y is incremented twice.)
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Adjust this driver to use driver model and move smdk5420 boards over to
use it.
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the sandbox cros_ec emulation driver to work with driver model, and
switch over to driver model for sandbox cros_ec.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for driver model if enabled. This involves minimal changes
to the code, mostly just plumbing around the edges.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
An incorrect message version is passed to the EC in some cases and the
parameters of one function are switched.
Fix these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ajay Kumar <ajaykumar.rs@samsung.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
commit 18b06652cd "tools: include u-boot version of sha256.h"
unconditionally forced the sha256.h from u-boot to be used
for tools instead of the host version. This is fragile though
as it will also include the host version. Therefore move it
to include/u-boot to join u-boot/md5.h etc which were renamed
for the same reason.
cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
For fsl-lsch3 NOR flash boot, IFC CS0 needs to be binded with address
within 32-bit at fist. After u-boot relocates to DDR, CS0 can be binded
to higher address to support large space.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
Add yet another OCOTP driver for this i.MX family. This time, it's a driver for
the OCOTP variant found in the i.MX23 and i.MX28. This version of OCOTP is too
different from the i.MX6 one that I could not use the mxc_ocotp.c driver without
making it into a big pile of #ifdef . This driver implements the regular fuse
command interface, but due to the IP blocks' limitation, we support only READ
and PROG functions.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The Chrome EC has a feature where you can access its I2C buses through a
pass-through arrangement. Add a command to support this, and export the
function for it also.
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple emulation of the Chrome OS EC for sandbox, so that it can
perform various EC tasks such as keyboard handling.
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Due to signed/unsigned comparison, '< sizeof(struct)' does not do the right
thing, since if ec_command() returns a -ve number we will consider this be
success.
Adjust all comparisons to avoid this problem.
This error was found with sandbox, which gives a segfault in this case. On
ARM we may instead silently fail.
We should also consider turning on -Wsign-compare to catch this sort of thing
in future.
Reviewed-by: Andrew Chew <achew@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
Tested-by: Andrew Chew <achew@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jimmy Zhang <jimmzhang@nvidia.com>
Protocol version 3 will be attempted first; if the EC doesn't support
it, u-boot will fall back to the old protocol version (2).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Protocol v2 was shipped with snow, link and spring. Protocol v3 is for
pit and is targetted at SPI operation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Version 1 protocols (without command version) were already no longer
supported in cros_ec.c. This removes some dead code from the
cros_ec_i2c driver.
Version 2 protcols (with command version) are now called
protocol_version=2, instead of cmd_version_is_supported=1.
A subsequent change will introduce protocol version 3 for SPI.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to support old style EC moving forward. Ultimately we
should get rid of the check_version() API. For now just return error
in case the EC does not seem to support the new API.
Reviewed-by: Vadim Bendebury <vbendeb@google.com>
Tested-by: Vadim Bendebury <vbendeb@google.com>
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
In order to talk to the EC properly we need to be able to understand the
layout of its internal flash memory. This permits emulation of the EC
for sandbox, and also software update in a system with a real EC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This allows us to put the SPI flash chip inside the SPI interface node,
with U-Boot finding the correct bus and chip select automatically.
Signed-off-by: Simon Glass <sjg@chromium.org>
Freescale IFC controller has been used for mpc8xxx. It will be used
for ARM-based SoC as well. This patch moves the driver to driver/misc
and fix the header file includes.
Signed-off-by: York Sun <yorksun@freescale.com>
Some GPIO connected LEDs have inverted polarity.
Introduce new config option: CONFIG_GPIO_LED_INVERTED_TABLE for the
specifying the inverted GPIO LEDs list and add support for this in the
gpio_led driver.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
Add a check for the gpio_request() function return value and do not try
to configure the GPIO if the gpio_request() call fails.
Also, print an error message indicating the gpio_request() has failed.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Ilya Ledvich <ilya@compulab.co.il>
This patch adds LPC support for carrying out the cros_ec protocol.
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds SPI support for carrying out the cros_ec protocol.
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
This patch adds I2C support for carrying out the cros_ec protocol.
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This patch adds the cros_ec driver that implements the protocol for
communicating with Google's ChromeOS embedded controller.
Signed-off-by: Bernie Thompson <bhthompson@chromium.org>
Signed-off-by: Bill Richardson <wfrichar@chromium.org>
Signed-off-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Gabe Black <gabeblack@chromium.org>
Signed-off-by: Hung-ying Tyan <tyanh@chromium.org>
Signed-off-by: Louis Yung-Chieh Lo <yjlou@chromium.org>
Signed-off-by: Randall Spangler <rspangler@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
u-boot standard i2c register write prototype is
i2c_reg_write(u8 addr, u8 reg, u8 val)
twl4030_i2c_write_u8(u8 addr, u8 val, u8 reg)
does not provide consistency, so switch the prototype to be
consistent with rest of u-boot i2c operations:
twl4030_i2c_write_u8(u8 addr, u8 reg, u8 val)
Signed-off-by: Nishanth Menon <nm@ti.com>
This command is useful to allow to observe messages generated by
coreboot and u-boot until present. In particular it is handy when
u-boot is instrumented to fall through into console mode on startup
errors.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch builds upon the recently introduced CBMEM console
feature of coreboot.
CBMEM console uses a memry area allocated by coreboot to store
the console output. The memory area has a certain structure,
which allows to determine where the buffer is, the buffer size
and the location of the pointer in the buffer. This allows
different phases of the firmware (rom based coreboot, ram based
coreboot, u-boot after relocation with this change) to keep
adding text to the same buffer.
Note that this patch introduces a new console driver and adds the
driver to the list of drivers to be used for console output, i.e.
it engages only after u-boot relocates. Usiong CBMEM console for
capturing the pre-relocation console output will be done under a
separate change.
>From Linux, run the cbmem.py utility (which is a part of the coreboot
package) to see the output, e.g.:
vvvvvvvvvvvvvvvvv
SCSI: AHCI 0001.0300 32 slots 6 ports ? Gbps 0xf impl SATA mode
flags: 64bit ilck stag led pmp pio
...
Magic signature found
Kernel command line: "cros_secure quiet loglevel=1 console=tty2...
^^^^^^^^^^^^^^^^^
Note that the entire u-boot output fits into the buffer only if
the coreboot log level is reduced from the most verbose. Ether
the buffer size will have to be increased, or the coreboot
verbosity permanently reduced.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
It's arch code and not a driver, so move it where it belongs. When it
originally went into drivers/misc there was no 8xxx CPU directory.
This will make new-SPL support a little easier since we can keep the CPU
stuff together and not need to pull stuff in from drivers/misc.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andy Fleming <afleming@freescale.com>
The PMIC framework has been moved to its more natural place
./drivers/power from ./drivers/misc directory.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The PMIC framework has been extended to support multiple instances of
the variety of devices responsible for power management.
This change allows supporting of e.g. fuel gauge, charger, MUIC (Micro USB
Interface Circuit).
Power related includes have been moved to ./include/power directory.
This is a first of a series of patches - in the future "pmic" will be
replaced with "power".
Two important issues:
1. The PMIC needs to be initialized just after malloc is configured
2. It uses list to hold information about available PMIC devices
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
PMIC MAX8997 is now ready to work with single and multibus soft I2C
implementation.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Since the pmic_reg_read is the u32 value, the order in which bytes
are placed to form u32 value is important.
Support for big and little sensor endianess is added.
Moreover calls to [leXX|beXX]_to_cpu have been added to support
little and big endian SoCs.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch adds support for proper handling of a PMIC I2C transmission
comprising of two bytes.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
When boot from PCIE, slave's core should be in holdoff after powered on for
some specific requirements. Master will release the slave's core at the
right time by PCIE interface.
Slave's ucode and ENV can be stored in master's memory space, then slave
can fetch them through PCIE interface. For the corenet platform, ucode is
for Fman.
NOTE: Because the slave can not erase, write master's NOR flash by
PCIE interface, so it can not modify the ENV parameters stored
in master's NOR flash using "saveenv" or other commands.
environment and requirement:
master:
1. NOR flash for its own u-boot image, ucode and ENV space.
2. Slave's u-boot image is in master NOR flash.
3. Put the slave's ucode and ENV into it's own memory space.
4. Normally boot from local NOR flash.
5. Configure PCIE system if needed.
slave:
1. Just has EEPROM for RCW. No flash for u-boot image, ucode and ENV.
2. Boot location should be set to one PCIE interface by RCW.
3. RCW should configure the SerDes, PCIE interfaces correctly.
4. Must set all the cores in holdoff by RCW.
5. Must be powered on before master's boot.
For the slave module, need to finish these processes:
1. Set the boot location to one PCIE interface by RCW.
2. Set a specific TLB entry for the boot process.
3. Set a LAW entry with the TargetID of one PCIE for the boot.
4. Set a specific TLB entry in order to fetch ucode and ENV from
master.
5. Set a LAW entry with the TargetID one of the PCIE ports for
ucode and ENV.
6. Slave's u-boot image should be generated specifically by
make xxxx_SRIO_PCIE_BOOT_config.
This will set SYS_TEXT_BASE=0xFFF80000 and other configurations.
In addition, the processes are very similar between boot from SRIO and
boot from PCIE. Some configurations like the address spaces can be set to
the same. So the module of boot from PCIE was added based on the existing
module of boot from SRIO, and the following changes were needed:
1. Updated the README.srio-boot-corenet to add descriptions about
boot from PCIE, and change the name to
README.srio-pcie-boot-corenet.
2. Changed the compile config "xxxx_SRIOBOOT_SLAVE" to
"xxxx_SRIO_PCIE_BOOT", and the image builded with
"xxxx_SRIO_PCIE_BOOT" can support both the boot from SRIO and
from PCIE.
3. Updated other macros and documents if needed to add information
about boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When compile the slave image for boot from SRIO, no longer need to
specify which SRIO port it will boot from. The code will get this
information from RCW and then finishes corresponding configurations.
This has the following advantages:
1. No longer need to rebuild an image when change the SRIO port for
boot from SRIO, just rewrite the new RCW with selected port,
then the code will get the port information by reading new RCW.
2. It will be easier to support other boot location options, for
example, boot from PCIE.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
As mx53loco board has two variants: one with Dialog PMIC and another with FSL MC34708 PMIC,
we need to be able to build both drivers.
Change pmic_init() and PMIC_NUM_OF_REGS names to avoid build conflicts when both drivers are present.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This commit adds support for MAX8997 PMIC driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This fixes write access to PMIC registers, the bug was
introduced partly in commit 64aac65099 and in commit c9fe76dd91.
It was tested on an i.mx31 with a mc13783.
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Stefano Babic <sbabic@denx.de>
Instead of using directly the i2c_set_bus() function,
the I2C_SET_BUS macro must be used to avoid build
errors for targets without multibus I2C.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This commit adds support for MAX8998 PMIC driver.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
I2C or SPI PMIC devices can be accessed.
Separate files: pmic_i2c.c and pmic_spi.c are responsible
for handling transmission over I2C or SPI bus.
New flags:
CONFIG_PMIC - enable PMIC general device.
CONFIG_PMIC_I2C/SPI - specify the interface to be used.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
This is cosmetic patch for the help message:
Before:
pmic dump [numregs] dump registers
After:
pmic dump [numregs] - dump registers
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
There was a mix of UTF-8 and ISO-8859 files in the U-Boot source
tree, which could cause issues with the patchwork review system.
This commit converts all ISO-8859 files to UTF-8.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
If some pre-boot or earlier stage bootloader (NAND SPL) has setup LAW
entries consider them good and mark them used.
In the NAND SPL case we skip re-initializing based on the law_table
since the SPL phase already did that.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We had an extra '0x' in the output of the LAWAR header that would cause
output like:
LAWBAR11: 0x00000000 LAWAR0x11: 0x80f0001d
intead of:
LAWBAR11: 0x00000000 LAWAR11: 0x80f0001d
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds helper funtions for basic access to the registers
of the MC9sdz60 chip (multifunctional device with RTC and CAN) via
I2C interface.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1014 is similar to the P1010 processor with the following differences:
- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
* TCP/IP acceleration and classification capabilities
* IEEE 1588 support
* Lossless flow control
* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
Split the display command into generic interface and hardware-specific
realization for PDSP188x LED display found on hmi1001 and manroland
boards. Simple interface for LED displays is defined in
include/led-display.h and described in doc/README.LED_display.
Driver-specific implementation was moved into drivers/misc/pdsp188x.c
file (enabled with CONFIG_PDSP188x set).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
The actual SPI driver for i.MX31 and i.MX51 controller
use a wrong byte ordering, because it is supposed
to work only with Freescale's devices, as the Power
Controllers (PMIC). The driver is not suitable for
general purposes, because the buffers passed to spi_xfer
must be 32-bit aligned, as it is used mainly to send
integer to PMIC devices.
The patch drops any kind of limitation and makes the
driver useful with devices controlled sending commands
composed by single bytes (or by a odd number of bytes), such as
spi flash, sensor, etc.
Because the byte ordering is changed,
any current driver using this controller must be adapted, too.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>