USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The change adds a number of macro definitions used by USB OHCI driver,
if CONFIG_USB_OHCI_LPC32XX is selected from a board config file.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate USB driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx USB driver
- lpc3250 header file USB registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
A number of LPC32xx SLC NAND defines is dictated by controller
hardware limits and OOB layout is defined by operating system, the
definitions are common for all users. Since those macro are used
in out of NAND SLC driver code (simple NAND SPL framework), they can
not be placed into the driver, therefore move them from board config
files to arch/config.h
The change also adds OOB layout details specific to small page NAND
devices taken from Linux kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Incorporate DMA driver from legacy LPCLinux NXP BSP.
The files taken from the legacy patch are:
- lpc32xx DMA driver
- lpc3250 header file DMA registers definition.
The legacy driver was updated and clean-up as part of the integration with the latest u-boot.
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Vladimir Zapolskiy <vz@mleia.com>
Enable TI_EDMA3 and SPL_DMA support, so as to reduce boot time. With
DMA enabled there is almost 3x improvement in read performance. This
helps in reducing boot time in qspiboot mode
Also add EDMA3 base address for DRA7XX and AM57XX.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Adds functions to enable and disable edma3 clocks which can be invoked
by drivers using edma3 to control the clocks.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add do_disable_clocks() to disable clock domains and module clocks.
These clocks are enabled using do_enable_clocks().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Add missing registers in struct definition.
Update GPIO MUX base register to match GPIO base (refer to "LPC32x0 User manual" Rev. 3 - 22 July 2011).
Signed-off-by: Sylvain Lemieux <slemieux@tycoint.com>
Move arch/arm/cpu/armv7/exynos/* to arch/arm/mach-exynos/* to allow
reuse of existing code for ARMv8 based Exynos platforms.
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add support for the mipi pll, this is necessary for getting higher dotclocks
with lcd panels.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The tv-encoder on sun5i is slightly different compared to the one on
sun4i/sun7i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This header file uses type definitions (u8, u32) from linux/types.h but
doesn't include it. If includes aren't carefully ordered this can cause
build failures.
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add defines to allow reading recovery mode (RCM) boot type from the boot
information table (BIT) written by the boot ROM (BR) to the IRAM.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The "method" parameter was part of the original port of the driver from
the kernel. At some point this may have been added to allow for future
differentiation (as omap1 and omap2 have different GPIO IP blocks, so
this wasn't an unreasonable thing to do). At this point however it's
just extra overhead, so drop.
Signed-off-by: Tom Rini <trini@konsulko.com>
AM43XX SoCs support up to 192 GPIO signals.
Make this amount available to the driver.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
This patch adds the glue code for hi6220 SoC which has 2x synopsis
dw_mmc controllers. This will be used by the hikey board support
in subsequent patches.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the header files which will be used in the subsquent
board / drivers to enable support for hi6220 hikey board.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reboot mode is written in scratchpad memory before reboot in the form of a
single char, that is the first letter of the reboot mode string as passed to the
reboot function.
This mechanism is supported on OMAP3 both my the upstream kernel and by various
TI kernels.
It is up to each board to make use of this mechanism or not.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Enable BCM SF2 ethernet and PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for the at91sam9260 based board smartweb from
siemens. SPL is used without serial support, as this
SoC has only 4k sram for running SPL. Here a U-Boot
bootlog:
RomBOOT
>
U-Boot 2015.07-rc2-00109-g4ae828c (Jun 15 2015 - 09:31:16 +0200)
CPU: AT91SAM9260
Crystal frequency: 18.432 MHz
CPU clock : 198.656 MHz
Master clock : 99.328 MHz
Watchdog enabled
DRAM: 64 MiB
WARNING: Caches not enabled
NAND: 256 MiB
In: serial
Out: serial
Err: serial
Net: macb0
Hit any key to stop autoboot: 0
U-Boot>
Signed-off-by: Heiko Schocher <hs@denx.de>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To enable NAND flash in sunxi SPL,
pins 0-6, 8-22 and 24 on port C are configured.
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
T124/210 requires some specific configuration (VPR setup) to
be performed by the bootloader before the GPU can be used.
For this reason, the GPU node in the device tree is disabled
by default. This patch enables the node if U-boot has performed
VPR configuration.
Boards enabled by this patch are T124's Jetson TK1 and Venice2
and T210's P2571.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
U-boot is responsible for enabling the GPU DT node after all necessary
configuration (VPR setup for T124) is performed. In order to be able to
check whether this configuration has been performed right before booting
the kernel, make it happen during board_init().
Also move VPR configuration into the more generic gpu.c file, which will
also host other GPU-related functions, and let boards specify
individually whether they need VPR setup or not.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Added PLL variables (dividers mask/shift, lock enable/detect, etc.)
to new pllinfo struct for each Soc/PLL. PLLA/C/D/E/M/P/U/X.
Used pllinfo struct in all clock functions, validated on T210.
Should be equivalent to prior code on T124/114/30/20. Thanks
to Marcel Ziswiler for corrections to the T20/T30 values.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs
to be measured - should be close to 700MHz (1.4G/2).
Note that some freqs aren't in the PLLU table in T210 TRM
(13, 26MHz), so I used the 12MHz table entry for them. They
shouldn't be selected since they're not viable T210 OSC freqs.
Since there are now 2 new OSC defines, all tables (pll_x_table,
PLLU) had to increase by two entries, but since 38.4/48MHz are
not viable osc freqs on T20/30/114, etc, they're just set to 0.
Signed-off-by: Tom Warren <twarren@nvidia.com>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Define base address of both usb xhci controllers in lsch3 config
in the format (IMMR + offset) for LS2085A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_CACHELINE_SIZE for LS2085A which is required by
USB XHCI stack for alignment
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
