Add a document to describe file system firmware loader binding
information.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Provide information about
- overview of file system firmware loader driver model
- describe storage device and partition in device tree source
- describe fie system firmware loader API
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the section about Device Trees add a paragraph at the end that
clarifies how we decide of a tree is valid or not. We say that all
bindings must either be in the specification (link provided) or in our
device-tree-bindings directory. We say that most of these come from the
Linux Kernel and as such some design decisions are made for us already,
but that in most cases we wish to retain compatibility.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
NAND flavors, like serial and parallel, have a lot in common and would
benefit to share code. Let's move raw (parallel) NAND specific code in a
raw/ subdirectory, to ease the addition of a core file in nand/ and the
introduction of a spi/ subdirectory specific to SPI NANDs.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Stefan is listed as a kirkwood maintainer since commit f822d8578b
(MAINTAINERS: Update Marvell custodianship).
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Add support for K3 based remoteproc driver that
communicates with TISCI to start start a remote processor.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
K3 specific SoCs have a dedicated microcontroller for doing
resource management. Any HLOS/firmware on compute clusters should
load a firmware to this microcontroller before accessing any resource.
Adding support for loading this firmware.
After the K3 system controller got loaded with firmware and started
up it sends out a boot notification message through the secure proxy
facility using the TI SCI protocol. Intercept and receive this message
through the rproc start operation which will need to get invoked
explicitly after the firmware got loaded.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Secure Proxy module manages hardware threads that are meant
for communication between the processor entities. Adding
support for this driver.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Devices from the TI K3 family of SoCs like the AM654x contain a Device
Management and Security Controller (SYSFW) that manages the low-level
device control (like clocks, resets etc) for the various hardware
modules present on the SoC. These device control operations are provided
to the host processor OS through a communication protocol called the TI
System Control Interface (TI SCI) protocol.
This patch adds a system reset driver that communicates to the system
controller over the TI SCI protocol for allowing to perform a system-
wide SoC reset.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a power domain driver that communicates to the system
controller over the TI SCI protocol for performing power management of
various devices present on the SoC. Various power domain functionalities
are achieved by the means of different TI SCI device operations provided
by the TI SCI framework.
This code is loosely based on the drivers/soc/ti/ti_sci_pm_domains.c
driver of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a clock driver that communicates to the system
controller over the TI SCI protocol for performing clock management of
various devices present on the SoC. Various clock functionality is
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/clk/keystone/sci-clk.c driver
of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a reset driver that communicates to the system
controller over the TI SCI protocol for performing reset management of
various devices present on the SoC. Various reset functionalities are
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/reset/reset-ti-sci.c driver of
the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Texas Instrument's System Control Interface (TI SCI) message protocol is
used in Texas Instrument's System on Chip (SoC) such as those in the K3
family AM654 SoC to communicate between various compute processors with
a central system controller entity.
The TI SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
This is mostly derived from the TI SCI driver in Linux located at
drivers/firmware/ti_sci.c.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
arch/arm/Makefile references armv5 for backwards compatibility with
older compilers. This patch removes those references to armv5,
since by now newer compilers are required which should have armv7
support enabled.
The Makefile also also has a list of options for mtune, but the
entry for CONFIG_CPU_V7A is empty, so this patch tunes the
CPU_V7A architecture to generic-armv7-a.
The following size changed apply to omap3_logic using GCC.
Stock
text data bss dec hex filename
50910 429 67580 118919 1d087 spl/u-boot-spl
540713 22700 327072 890485 d9675 u-boot
Without Armv5
text data bss dec hex filename
50916 429 67580 118925 1d08d spl/u-boot-spl
540719 22700 327064 890483 d9673 u-boot
mtune=generic-armv7-a
text data bss dec hex filename
50932 429 67580 118941 1d09d spl/u-boot-spl
540519 22700 327080 890299 d95bb u-boot
Signed-off-by: Adam Ford <aford173@gmail.com>
There is no need to keep a separate coreboot_fb.dtsi since now we
have a generic coreboot payload dts.
While we are here, this also remove the out-of-date description in
the documentation regarding to coreboot framebuffer driver with
U-Boot loaded as a payload from coreboot. As the testing result with
QEMU 2.5.0 shows, the driver just works like a charm.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently building U-Boot as the coreboot payload requires user
to change the build configuration for a specific board during
menuconfig process. This uses the board's native device tree
to configure the hardware. For example, the device tree provides
PCI address range for the PCI host controller and U-Boot will
re-program all PCI devices' BAR to be within this range. In order
to make sure we don't mess up the hardware, we should guarantee
the range matches what coreboot programs the chipset.
But we really should make the coreboot payload support easier.
Just like EFI payload, we can create a generic coreboot payload
for all x86 boards as well. The payload is configured to include
as many generic drivers as possible. All stuff that touches low
level initialization are not allowed as such is the coreboot's
responsibility. Platform specific drivers (like gpio, spi, etc)
are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Add u-boot,off-on-delay-us for fixed regulator.
Depends on board design, the gpio regulator sometimes
connects with a big capacitance. When need to off, then
on the regulator, if there is no enough delay,
the voltage does not drop to 0, so introduce this
property to handle such case.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Compressed images should have their compression property
set to "none" if U-Boot should leave them compressed.
This is especially the case for compressed ramdisks that
should be uncompressed by the kernel only.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chip Version is a string saved in BOOTROM address space Little Endian.
Ex for rk3288: 0x33323041 0x32303134 0x30383133 0x56323030
which brings: 320A20140813V200
Note that memory version do invert MSB/LSB so printing the char
buffer would show: A02341023180002V
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
At present all emulated sandbox pci devices must be present in the
device tree in order to be used. The real world pci uclass driver
supports pci device driver matching, and we should add such support
on sandbox too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds documentation of device tree bindings for the STM32 ADC.
It's based on linux-v4.18-rc* dt-bindings, at the time of writing:
- Documentation/devicetree/bindings/iio/adc/st,stm32-adc.txt
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
patman's _ReadAliasFile only splits on spaces, not tabs, so the entries
for dinh and maxime weren't being recognised as valid. I'll fix patman
in a separate patch, but this makes all the entries consistent.
Signed-off-by: Adam Sampson <ats@offog.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Scott is no longer maintaining the NAND subsystem, mark as orphaned for
now.
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit c524997acb.
Booting ARMv7 in non-secure mode using bootefi works now.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Switch to the distro boot for UniPhier platform.
- Remove the environment vairalbes used to load images from raw
block devices.
- Keep the command to download images via tftp. This will be
useful to boot the kernel when no valid kernel image is ready
yet in the file system.
- Use root.cpio.gz instead of root.cpio.uboot because we always know
the file size of the init ramdisk; it is loaded via either a file
system or network.
- Rename fit_addr_r to kernel_addr_r, which the distro command
checks to get the load address of FIT image.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently the U-Boot project contains 2 documentation directories:
- doc/
- Documentation/
The Documentation directory only contains device tree bindings related
content, so move the 3 files to doc/device-tree-bindings/.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
1. Since libavb library alone is highly portable, introduce dedicated
Kconfig symbol for AVB bootloader-dependent operations, so it's possible
to build libavb separately. AVB bootloader-dependent operations include:
* Helpers to process strings in order to build OS bootargs.
* Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c.
* Helpers to alloc/init/free avb ops.
2. Add CONFIG_FASTBOOT dependency, as fastboot buffer is
re-used in partition verification operations.
Reported-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
The Linux kernel moved to sphinx-based documentation and got rid of the
DocBook based documentation quite a while ago. Hence, the DocBook
documentation for U-Boot should be converted as well.
To achieve this, import the necessary files from Linux v4.17, and
convert the current DocBook documentation (three files altogether) to
sphinx/reStructuredText.
For now, all old DocBook documentation was merged into a single
handbook, tentatively named "U-Boot Hacker Manual".
For some source files, the documentation style was changed to comply
with kernel-doc; no functional changes were applied.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Change the description relating to CONFIG_SPL_ROCKCHIP_BACK_TO_BROM to
clarify that both RK3288 and RK3036 use
CONFIG_SPL_ROCKCHIP_BACK_TO_BROM=y
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To let the full U-Boot know where it was booted from (i.e. which of
the entries in /chosen/u-boot,spl-boot-order' contained a valid
image), we define (and document) /chosen/u-boot,spl-boot-device as the
property that could/should automatically be injected by SPL.
This commit only contains a documentation change, which documents the
new property and the intended usage.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
HSE and LSE bypass shall support both analog and digital signals.
This patch add a way to select digital bypas case in the device tree
and set the associated bit DIGBYP in RCC_BDCR and RCC_OCEN register
during clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Support a default memory bank, specified in reg, as well as
board-specific memory banks in subtree board-id nodes.
This allows memory information to be provided in the device tree,
rather than hard-coded in, which will make it simpler to handle
similar devices with different memory banks, as the board-id values
or masks can be used to match devices.
Signed-off-by: Michael Pratt <mpratt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
To build U-Boot on a Nyan Big Chromebook the docs outline adjusting the Tegra124
defined CONFIG_SYS_TEXT_BASE but this has since been moved to individual config
files. We should have the default required for U-Boot chain loading on the
chromebook as the default CONFIG_SYS_TEXT_BASE and update the docs to remove
this now non required step.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This updates the doc to mention chain-loading an x86 kernel via
'bootefi' command, along with several typos fix.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
CONFIG_EFI_LOADER is fully supported on x86 now.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Alexander Graf <agraf@suse.de>
Contains:
1. Overview of Android Verified Boot 2.0
2. Description of avb subset of commands
3. Examples of errors when boot/vendor/system/vbmeta partitions
are tampered
4. Examples of enabling AVB2.0 on your setup
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
To avoid confusion, let's rename the efi-x86 target to efi-x86_app.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible to create a generic EFI payload for all x86 boards.
The payload is configured to include as many generic drivers as
possible. All stuff that touches low-level initialization are not
allowed as such is the EFI BIOS's responsibility. Platform specific
drivers (like gpio, spi, etc) are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present the EFI application and payload support codes in the x86
directory is distributed in a hybrid way. For example, the Kconfig
options for both app and payload are in arch/x86/lib/efi/Kconfig,
but the source codes in the same directory get built only for
CONFIG_EFI_STUB.
This refactors the codes by consolidating all the EFI support codes
into arch/x86/cpu/efi, just like other x86 targets.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit f3b5056c4e ("efi_loader: split README.efi into two
separate documents"), the original README.efi was renamed to
README.u-boot_on_efi, but x86 doc still refers to the old one.
This updates the x86 doc to reference both README.u-boot_on_efi and
README.uefi.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently both pirq_reg_to_linkno() and pirq_linkno_to_reg() assume
consecutive PIRQ routing control registers. But this is not always
the case on some platforms. Introduce a new device tree property
intel,pirq-regmap to describe how the PIRQ routing register offset
is mapped to the link number and adjust the irq router driver to
utilize the mapping.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As README.x86 already mentions, there are two SPI flashes mounted
on Intel Cougar Canyon 2 board, called SPI-0 and SPI-1 respectively.
SPI-0 stores the flash descriptor and the ME firmware. SPI-1 stores
the actual BIOS image which is U-Boot. Building a single image with
both ME firmware and U-Boot does not make sense.
This also describes the exact flash location where the u-boot.rom
should be programmed in the documentation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit removes text that is exact duplicated of the text above.
Cc: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
With 'make htmldocs' we can generate a documentation if the function
comments follow the DocBook conventions.
This patch adjusts the comments for EFI boot services and provides the
DocBook template for the EFI subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Update the list of missing functionality for boottime and runtime services.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rename
nx25 as ax25
ae250 as ae350
nx25-ae250 as ax25-ae350
including filename, variable, string and definition.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>
For pinctrl driver of mvebu, the compatible strings
supported are defined differently from Linux version.
The patch aligned the compatible string with
Linux 4.17-rc4.
Signed-off-by: Evan Wang <xswang@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Sync sun4i-usb-phy bindings from Linux, since the
drivers/phy/allwinner/phy-sun4i-usb.c follow similar.
Sync changes from Linux with below commit:
"phy: sun4i-usb: add support for R40 USB PHY"
(sha1: f3d96f8d23d8e6d0b7642ee946b9b2ac3418fb4d)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Now that U-Boot works fine with highmem enabled, there is no need to
tell users to disable highmem.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Simon Glass <sjg@chromium.org>
Describe U_BOOT_CMD_COMPLETE.
Describe the arguments of U_BOOT_CMD and U_BOOT_CMD_COMPLETE.
Describe the arguments of the command function.
Describe the arguments of the completion function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Last user of this driver went away in May 2017 in commit
eb5ba3aefd ("i2c: Drop use of CONFIG_I2C_HARD").
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
Last user of this driver went away in June 2015 in commit
d928664f41 ("powerpc: 74xx_7xx: remove 74xx_7xx cpu support")
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Heiko Schocher <hs@denx.de>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable support for multiple loadable images in SEC firmware FIT image.
Also add example "sec_firmware_ppa.its" file.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add regulator driver for STM32 voltage reference buffer which can be
used as voltage reference for ADCs, DACs and external components through
dedicated VREF+ pin.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
- Based on commit 08ae21af96 ("MAINTAINERS: Switch nxp.com domain")
update or drop some formerly Freescale addresses.
- Update a few aliases to reflect current custodians
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Synchronize the README with the current state of U-Boot, unify
the build instructions to avoid duplication.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The default of DISTRO_DEFAULTS is messy. Using the 'imply' keyword
is equivalent and cleaner.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
As of clang-5.0, things have changed a bit. First, we cannot
automatically guess -target values as if we do not pass one with CC then
cc-option will fail. Second, to disable movt/movw relocations the
argument has become -mno-movt.
Related to the target part, we cannot use arm-none-eabi as that ends up
being too generic of an ARM target for things like say rpi_3_32b to
work.
Signed-off-by: Tom Rini <trini@konsulko.com>
We do not support bootefi booting ARMv7 in non-secure mode.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We only use coreboot as a target on x86 platforms, since on ARM platforms
U-Boot always runs as the primary boot loader. Rename the coreboot-x86
platform to reflect this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This updates the doc of booting VxWorks, like loading an x64 kernel,
and how to make VxWorks graphics console driver work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present two environment variables 'e820data'/'e820info' are required
to boot a VxWorks x86 kernel, but this is superfluous. The offset of
these two tables are actually at a fixed offset from the kernel memory
base address and we can provide the kernel memory base address to U-Boot
via only one variable 'vx_phys_mem_base'.
Note as it name indicates, the physical address should be provided.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This corrects a typo and updates several places for clarity.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
The u-boot-ivt.img.log file contains 0x prefixes in the HAB Blocks line,
while the SPL.log does not. For consistency, and to make it easier to
extract and put into a .csf file for use with NXP's code signing tool,
add 0x prefixes here.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Breno Lima <breno.lima@nxp.com>
The commit describe usage of gpios and pinctrl device tree
properties in order to enable gpio-based software deblocking.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Without the units these numbers are confusing. Add a comment about the
unit being 'bytes' and mention 'buildman' as the source.
Suggested-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Provides information about
- usage of the bootefi command
- overview of UEFI
- interaction between U-Boot and EFI drivers
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Leif Lindholm <leif.lindholm@linaro.org>
Acked-by: Leif Lindholm <leif.lindholm@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Delete README.efi. It is replaced by a further patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-on: http://vgitil04.il.marvell.com:8080/43289
Tested-by: iSoC Platform CI <ykjenk@marvell.com>
Reviewed-by: Kostya Porotchkin <kostap@marvell.com>
Reviewed-by: Igal Liberman <igall@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Simply record riscv-linux booting steps and messages
from bbl via u-boot on QEMU in README.ae250.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
The 2 functions board_power_mode and board_poweroff
are no more existing in U-Boot code (check with grep)
This patch updates the documentation and removes
the unnecessary prototypes.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Due to adding various new functionalities with SPI and SPI-FLASH
subsystems which are rounding in Mailing list for year these long
term supporting spi driver which never seen any update with
driver-model conversion.
So added migration plan for DM_SPI and DM_SPI_FLASH with
deadline v2018.09
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The README.mxc_hab is outdated and need improvements, add the following
modifications:
- Reorganize document and remove duplicate content
- Add CST download link
- Update CST package name
- Align command lines with CST v2.3.3
- Update U-Boot binary name
- Remove CSF padding since is not documented in AN4581
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Currently the High Assurance Boot procedure is documented in two
places:
- doc/README.imx6
- doc/README.mxc_hab
It is better to consolidate all HAB related information into
README.mxc_hab file, so move the content from README.imx6 to
README.mxc_hab.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
With the contents of config_distro_defaults.h migrated to Kconfig,
we can remove this header file completely
Signed-off-by: Adam Ford <aford173@gmail.com>
README.efi describes two different concepts:
* U-Boot exposing the UEFI API
* U-Boot running on top of UEFI.
This patch splits the document in two.
Religious references are removed.
The separation of the concepts makes sense before detailing the internals
of U-Boot exposing the UEFI API in a future patch.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This commit cleans up the README.watchdog by removing the reminescent of
ADI's Blackfin architecture removed some time ago.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The original text is from the time that the config options were not
converted to Kconfig.
After the conversion to Kconfig only CONFIG_SECURE_BOOT and
CONFIG_CMD_DEKBLOB need to be selected by the user.
The other config options are automatically selected by the Kconfig
logic.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Breno Lima <breno.lima@nxp.com>
The EFI implementation does not fit into any of the existing categories.
Provide LOGC_EFI so that EFI related message can be filtered.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When functions return an error it propagates up the stack to the point
where it is reported. Often the error code provides enough information
about the root cause of the error that this is obvious what went wrong.
However in some cases the error may be hard to trace. For example if a
driver uses several devices to perform an operation, it may not be
obvious which one failed.
Add a log_ret() macro to help with this. This can be used to wrap any
error-return value. The logging system will then output a log record when
the original error is generated, making it easy to trace the call stack
of the error.
This macro can significantly impact code size, so its use is controlled
by a Kconfig option, which is enabled for sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
The appended README explains how U-Boot and iPXE can be used
to boot a diskless system from an iSCSI SAN.
The maintainer for README.efi and README.iscsi is set.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: s/Adress/Address/]
Signed-off-by: Alexander Graf <agraf@suse.de>
NAND and QSPI devices are now supported, so mark
them as such.
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update documentation to reflect adopting the Linux DT bindings.
Tested on TI K2G platform:
Tested-by: Vignesh R <vigneshr@ti.com>
Tested on a socfpga-cyclonev board:
Tested-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Signed-off-by: Jason Rush <jarush@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Acked-by: Marek Vasut <marex@denx.de>
Migrate the following symbols to Kconfig:
CONFIG_FS_EXT4
CONFIG_EXT4_WRITE
The definitions in config_fallbacks.h can now be expressed in Kconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
It's mostly obvious, except that QEMU is annoying and requires an
explicit '-cpu cortex-a57' (or some other 64-bit core) to actually run
in 64-bit mode.
While at it, remove the references to setting the ARCH environment
variable; that is not used in U-Boot.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in various documentation files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address of a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in the FIT image example files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Fix all occurences in the FIT image documentation files where this was not
observed, to not give bad examples to the reader.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add documents to describe NX25 and AE250.
Also update other documents for RISC-V.
Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Signed-off-by: Greentime Hu <green.hu@gmail.com>
add a simple readme to introduce rockusb and tell people how to use it
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Linux bindings have been introduced in the code (removing the U-Boot
specific ones) without documentation update. Compatible string has
changed, as well as the four GPIO properties. Reflect this by updating
the soft-spi.txt documentation.
Fixes: 102412c415 ("dm: spi: soft_spi: switch to use linux compatible string")
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch extends pmic_bind_children prefix matching. In addition to
the node name the property regulator-name is used while trying to match
prefixes. This allows assigning different drivers to regulator nodes
named regulator@1 and regulator@10 for example.
I have discarded the idea of using other properties then regulator-name
as I do not see any benefit in using property compatible or even
regulator-compatible. Of course I am open to change this if there are
good reasons to do so.
Signed-off-by: Felix Brack <fb@ltec.ch>
Reviewed-by: Simon Glass <sjg@chromium.org>
For external data, FIT has a optional property "data-position" which
can set the external data to a fixed offset to FIT beginning.
Add the support for this property in SPL FIT.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tomas Melin <tomas.melin@vaisala.com>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: "Andrew F. Davis" <afd@ti.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: "tomas.melin@vaisala.com" <tomas.melin@vaisala.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Andre Przywara <andre.przywara@arm.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: "Cooper Jr., Franklin" <fcooper@ti.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Rick Altherr <raltherr@google.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Synopsys HSDK clock controller generates and supplies clocks to various
controllers and peripherals within the SoC.
Each clock has assigned identifier and client device tree nodes can use
this identifier to specify the clock which they consume. All available
clocks are defined as preprocessor macros in the
dt-bindings/clock/snps,hsdk-cgu.h header and can be used in device
tree sources.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The reset circuitry in the RK3399 only resets 'almost all logic' when
a software reset is performed. To make our software maintenance
easier in the future, we want to have the option (controlled by a DTS
property) to force all reset causes other than a power-on reset to
trigger a power-on reset via a GPIO trigger.
This adds the necessary support to the rk3399-puma (i.e. RK3399-Q7)
board-support and the documentation for the new property
(sysreset-gpio) within the /config-node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a document to describe Andestech atcpit100 timer and
binding information.
Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This DT binding doc is porting from Linux DT binding doc.
commit 1adcbea4201a6852362aa5ece573f1f169b28113
Add a device tree bindings document for the SoCFPGA Arria10
FPGA Manager driver.
Signed-off-by: Alan Tull <atull@opensource.altera.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-By: Moritz Fischer <moritz.fischer@ettus.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
For the RK3188, the BROM will attempt to load up the first stage
image (SPL for the RK3188) in two steps: first 1KB to offset 0x800
in the SRAM and then the remainder to offset 0xc00 in the SRAM.
It always enters at 0x804, though.
With this changeset, the RK3188 boot removes the TPL (stub) stage and
builds a single SPL binary that utilizes the early back-to-bootrom via
the boot0-hook.
Consequently, the passing of the saved boot params via pmu->os_reg[2]
is also removed.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dra7xx series of SOCs contain a temperature sensor and an
associated analog-to-digital converter (ADC) which produces
an output which is proportional to the SOC temperature.
Add support for this temperature sensor.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Coccinelle is a program for static code analysis.
For details on Coccinelle see
http://coccinelle.lip6.fr/
Add scripts/coccicheck copied from Linux kernel v4.14.
The coccicheck script executes the tests *.cocci in
directory scripts/coccinelle by calling spatch.
In Makefile add a coccicheck target. You can use it with
make coccicheck MODE=<mode>
where mode in patch, report, context, org.
Add a copy of Linux v4.14 file Documentation/dev-tools/coccinelle.rst
as doc/README.coccinelle.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Allow the platform to define a partition by name at the end of which
the environment data will be located.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This patch fixed U-Boot proper location has been
missed to update in bewlo commit
"rockchip: doc: update U-Boot location info"
(sha1: 73e6dbe855)
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The U-Boot location has been moved to block 16384.
This is 8MB, not 4MB.
Signed-off-by: Simon Goldschmidt <sgoldschmidt@de.pepperl-fuchs.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Update rockchip U-Boot location to 0x4000/16384.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
As you see in crypto_algos in common/image-sig.c, the algorithm
should be either "rsa2048" or "rsa4096". "rs2048" is a typo.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Up to now we depended on an exported variable to build u-boot.rom.
We should be able to specify it in the configuration file, too.
With this patch this becomes possible using the new Kconfig option
CONFIG_BUILD_ROM.
This option depends on CONFIG_X86 and is selected in
qemu-x86_defconfig and qemu-x86_64_defconfig.
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust VGA rom address to 0xfffb0000 so that u-boot.rom image
can be built again.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The changes required to use U-Boot's Serial Download Protocol
implementation are now available in upstream imx_usb_loader
repository. Update the URL accordingly.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that it is possible to load SPL and u-boot.img via imx_usb_loader
tool, mention this method instead of the old one that relied on ymodem.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The regulator bindings state that regulator prefixes are allowd to be
in upper or lower case. However pmic_bind_children from pmic_uclass uses
strncmp to compare DT node name against prefix. This comparison is case
sensitive hence the regulator driver prefix case matters.
Signed-off-by: Felix Brack <fb@ltec.ch>
u-boot can be embedded within a FIT image with multiple DTBs. It then
selects at run-time which one is best suited for the platform.
Use the same principle here for the SPL: put the DTBs in a FIT image,
compress it (LZO, GZIP, or no compression) and append it at the end of the
SPL.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
[trini: Move default y of SPL_MULTI_DTB_FIT_DYN_ALLOC to it being the
default choice if SYS_MALLOC_F, drop spl.h include from lib/fdtdec.c
it's unused.]
Signed-off-by Tom Rini <trini@konsulko.com>
CONFIG_FIT_EMBED might be confused with CONFIG_OF_EMBED, rename it
MULTI_DTB_FIT as it is able to get a DTB from a FIT image containing
multiple DTBs. Also move the option to the Kconfig dedicated to the DTS
options and create a README for this feature.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The g_dnl USB settings for the vendor ID, product ID and manufacturer are
actually common settings that can and should be shared by all the gadgets.
Make them common by renaming them, and convert all the users.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It is often desirable to configure the spl-boot-order (i.e. the order
that SPL probes devices to find the FIT image containing a full U-Boot)
such that it contains 'the same device the SPL stage was booted from'
early on. To support this, we introduce the 'same-as-spl' specifier
for the spl-boot-order property.
This commit adds:
- documentation for the new board_spl_was_booted_from() function that
individual SoCs/boards should provide, if they can determine where
the SPL was booted from
- implements the new board_spl_was_booted_from() stub function
- adds support for handling the 'same-as-spl' specifier and calling
into the per-SoC/per-board support code.
This also updates the documentation for the 'u-boot,spl-boot-order'
property.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the size of SPL can't be exceeded 0x8000 bytes in RK3288,
it is not possible add new SPL features like Falcon mode or etc.
So add TPL stage so-that adding new features to SPL is possible.
- TPL: DRAM init, clocks
- SPL: MMC, falcon, etc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This driver is adapted from linux drivers/reset/reset-stm32.c
It's compatible with STM32 F4/F7/H7 SoCs.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
To add support for each SoC family, a SoC's specific
include/dt-binfings/mfd/stm32xx-rcc.h file must be added.
This patch only includes stm32h7-rcc.h dedicated for STM32H7 SoCs.
Other SoCs support will be added in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver implements basic clock setup, only clock gating
is implemented.
This driver doesn't implement .of_match as it's binded
by MFD RCC driver.
Files include/dt-bindings/clock/stm32h7-clks.h and
doc/device-tree-bindings/clock/st,stm32h7-rcc.txt
will be available soon in a kernel tag, as all the
bindings have been acked by Rob Herring [1].
[1] http://lkml.iu.edu/hypermail/linux/kernel/1704.0/00935.html
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is the generic phy driver for the picoPHY ports
used by USB2/1.1 controllers. It is found on STiH407 SoC
family from STMicroelectronics.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The main difference between Pro4 and PXs2/LD6b is the Denali NAND
IP version. This is now distinguished by DT. Merge the two defconfig
files into uniphier_v7_defconfig.
Update the README.uniphier too.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This adds support to Intel Cherry Hill board, a board based on
Intel Braswell SoC. The following devices are validated:
- serial port as the serial console
- on-board Realtek 8169 ethernet controller
- SATA AHCI controller
- EMMC/SDHC controller
- USB 3.0 xHCI controller
- PCIe x1 slot with a graphics card
- ICH SPI controller with an 8MB Macronix SPI flash
- Integrated graphics device as the video console
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pull some information regarding overlays from commit messages and
put them directly within the documentation. Also add some information
regarding required dtc version to properly use overlays.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
We have the capability to apply overlays on the command line but
we didn't have a document explaining how.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Łukasz Majewski
Acked-by: Simon Glass <sjg@chromium.org>
Rather than naming the phandle struct according to the number of cells it
uses (e.g. struct phandle_2_cell) name it according to the number of
arguments it has (e.g. struct phandle_1_arg). This is a more intuitive
naming.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Add support for reading a list of bouncing addresses from a in-tree file
(doc/bounces) and from the ~/.patman config file. These addresses are
stripped from the Cc list.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com <mailto:philipp.tomsich@theobroma-systems.com>>
If CONFIG_SPL_OS_BOOT is enabled, boot OS if kernel image is found
in FIT structure.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL supports U-Boot image in FIT format which has data outside of
FIT structure. This adds support for embedded data for normal FIT
images.
Signed-off-by: York Sun <york.sun@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A number of the config options for USB networking have been migrated to
Kconfig. Update README.usb to reflect this.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Add some documentation for the live device tree support in U-Boot. This
was missing from the initial series.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
The CONFIG_BLK conversion involves quite invasive changes in the U-Boot
code, with #ifdefs and different code paths. We should try to move over to
this soon so we can drop the old code.
Set a deadline of 9 months for this work, rounded up to the next release.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Writing prepared FDT to persistent storage should be possible in
scripts. Create environment variables containing address and size
of the updated FDT. Scripts can use these variables after running
'spl export fdt ...' command to write the new blob to persistent
storage.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Document the U-Boot Serial Download Protocol implementation and
some typical use cases.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Łukasz Majewski <lukma@denx.de>
Add i2c driver which can be used on both STM32F7 and STM32H7.
This I2C block supports the following features:
_ Slave and master modes
_ Multimaster capability
_ Standard-mode (up to 100 kHz)
_ Fast-mode (up to 400 kHz)
_ Fast-mode Plus (up to 1 MHz)
_ 7-bit and 10-bit addressing mode
_ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask)
_ All 7-bit addresses acknowledge mode
_ General call
_ Programmable setup and hold times
_ Easy to use event management
_ Optional clock stretching
_ Software reset
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
