This patch adds a default ft_board_setup() routine to the 4xx fdt code.
This routine is defined as weak and can be overwritten by a board specific
one if needed.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes a problem with DIMMs that have 8 banks. Now the
MCIF0_MBxCF register will be setup correctly for this setup too.
This was noticed with the 512MB DIMM on Canyonlands/Glacier.
Signed-off-by: Stefan Roese <sr@denx.de>
Since the current dflush() implementation is know to have some problems
(as seem on lwmon5 ECC init) this patch removes it completely and replaces
it by using clean_dcache_range().
Tested on Katmai with ECC DIMM.
Signed-off-by: Stefan Roese <sr@denx.de>
On ppc405EP and ppc405GP (at least) the ebc is directly attached to the plb
and not to the opb. This patch will try to fixup /plb/ebc if /plb/opb/ebc
doesn't exist.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
The PCIe root-complex/endpoint setup as configured via the "pcie_mode"
environment variable will now get passed to the Linux kernel by setting
the device_type property of the PCIe device tree node. For normal root-
complex configuration it will keep its defaults value of "pci" and for
endpoint configuration it will get changed to "pci-endpoint".
Signed-off-by: Stefan Roese <sr@denx.de>
dcache_enable() was missing for 440 and the patch
017e9b7925 ["allow ports to override bootelf
"] behavior uses this function.
Note: Currently the cache handling functions like
d/icache_disable/enable() are NOP's on 440. This may be changed in the
future.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch assigns the correct EBC clock for 405GP(r) CPUs
to PPC4xx_SYS_INFO structure. Without this patch U-Boot
uses an uninitialized EBC clock in its startup message.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Currently U-Boot crashes in ppc_4xx_eth_init on sequoia
with cache enabled (TLB Parity exeption). This patch
fixes the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently U-Boot crashes on sequoia board in CPU POST if
cache is enabled (CONFIG_4xx_DCACHE defined). The cache
won't be disabled by change_tlb before CPU POST because
there is an insufficient adress range check since
CFG_MEM_TOP_HIDE was introduced. This patch tries to fix
this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch fixes a problem with the RGMII setup of the 460GT. The 460GT
has 2 RGMII instances and we need to configure the 2nd RGMII instance
for the EMAC2+3 channels.
Signed-off-by: Stefan Roese <sr@denx.de>
This bug was introduced with commit aee747f19b
which enabled CFG_4xx_GPIO_TABLE for PPC405 and unintentionally
disabled the setting of the emac noise filter bits for PPC405EP when CFG_4xx_GPIO_TABLE is set.
Signed-off-by: Markus Brunner <super.firetwister@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
On PPC440EPx without a bootstrap I2C EEPROM, the PLL can be reconfigured
after startup to change the speed of the clocks. This patch adds the
option CFG_PLL_RECONFIG. If this option is set to 667, the CPU
initialization code will reconfigure the PLL to run the system with a CPU
frequency of 667MHz and PLB frequency of 166MHz, without the need for an
external EEPROM.
Signed-off-by: Mike Nuss <mike@terascala.com>
Acked-by: Stefan Roese <sr@denx.de>
This patch adds support for the AMCC Glacier 460GT eval board.
The main difference to the Canyonlands board are listed here:
- 4 ethernet ports instead of 2
- no SATA port
- no USB port
Currently EMAC2+3 are not working. This will be fixed in a later
release.
Signed-off-by: Stefan Roese <sr@denx.de>
460EX doesn't support a fixed bootstrap option to boot from 512 byte page
NAND devices. The only bootstrap option for NAND booting is option F for
2k page devices. So to boot from a 512 bype page device, the I2C bootstrap
EEPROM needs to be programmed accordingly.
This patch adds basic NAND booting support for the AMCC Canyonlands aval
board and also adds support to the "bootstrap" command, to enable NAND
booting I2C setting.
Tested with 512 byte page NAND device (32MByte) on Canyonlands.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is a rework of the 4xx interrupt handling done while
adding the 460EX/GT support. Interrupts are needed on 4xx for the
EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes the physical addess parameter from 32bit to 64bit.
This is needed for 36bit 4xx platforms to access areas located
beyond the 4GB border, like SoC peripherals (EBC etc.).
Signed-off-by: Stefan Roese <sr@denx.de>
Every now and then a Sequoia board (or equivalent hardware) had
problems connecting to a Gigabit capable network interface.
There were differences in the PHY setup between Linux and U-Boot.
This patch fixes the problem. Apparently "remote fault" is being set,
which signals to some devices (on the other end of the cable) that a
fault has occurred, while other devices ignore it. I believe the RF bit
was causing the issue, but I removed T4 also, to match up with Linux.
Signed-off-by: Mike Nuss <mike@terascala.com>
The 405EZ only supports 512 bytes of rx-/tx-fifo EMAC sizes. But
currently 4k/2k is configured. This patch fixes this issue.
Thanks to Thomas Kindler <tkindler@lenord.de> for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
U-Boot crashes in the net loop if CONFIG_4xx_DCACHE is
enabled. To reproduce the problem ensure that 'ethrotate'
environment variable isn't set to "no" and then run
"tftp 200000 not_existent_file".
This patch tries to fix the issue.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
R29 was an unlucky choice as with recent toolchains (gcc-4.2.x) gcc
will refuse to use load/store multiple insns; instead, it issues a
list of simple load/store instructions upon function entry and exit,
resulting in bigger code size, which in turn makes the build for a
few boards fail.
Use r2 instead.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The current ndfc HW ECC implementation swaps the first two ECC bytes.
But the 4xx NDFC already uses the SMC (Smart Media Card) ECC ordering,
so this swapping in the HW ECC driver is bogus. This patch fixes this
problem and now really uses the SMC ECC byte order.
Thanks to Sean MacLennan for pointing this out.
Signed-off-by: Stefan Roese <sr@denx.de>
The privious 4xx POST implementation only supported storing the POST
WORD in OCM. Since we need to reserve the OCM on LWMON5 for the logbuffer
we need to store the POST WORD in some other non volatile location.
This patch adds CFG_POST_ALT_WORD_ADDR to specify an address for such
a location.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for locking the init-ram/stack in d-cache,
so that other regions may use d-cache as well
Note, that this current implementation locks exactly 4k of d-cache,
so please make sure that you don't define a bigger init-ram area. Take
a look at the lwmon5 440EPx implementation as a reference.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch allows the use of 4xx interrupt vector number defines
in board specific code outside cpu/ppc4xx.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Now that there are no board-specific versions of
"denali_core_search_data_eye()", the weak binding on the common version
can be removed.
Signed-off-by: Larry Johnson <lrj@acm.org>
On Katmai the complete auto-calibration somehow doesn't seem to
produce the best results, meaning optimal values for RQFD/RFFD.
This was discovered by GDA using a high bandwidth scope,
analyzing the DDR2 signals. GDA provided a fixed value for RQFD,
so now on Katmai "only" RFFD is auto-calibrated.
This patch also adds RDCC calibration as mentioned on page 7 of
the AMCC PowerPC440SP/SPe DDR2 application note:
"DDR1/DDR2 Initialization Sequence and Dynamic Tuning"
Signed-off-by: Stefan Roese <sr@denx.de>
This patch makes two additions to GPIO support:
First, it adds function gpio_read_in_bit() to read the a bit from the
GPIO Input Register (GPIOx_IR) in the same way that function
gpio_read_out_bit() reads a bit from the GPIO Output Register
(GPIOx_OR).
Second, it modifies function gpio_set_chip_configuration() to provide
an additional option for configuring the GPIO from the
"CFG_4xx_GPIO_TABLE".
According to the 440EPx User's Manual, when an alternate output is used,
the three-state control is configured in one of two ways, depending on
the particular output. The first option is to select the corresponding
alternate three-state control in the GPIOx_TRSH/L registers. The second
option is to select the GPIO Three-State Control Register (GPIOx_TCR) in
the GPIOx_TRSH/L registers, and set the corresponding bit in the
GPIOx_TCR register to enable the output. For example, the Manual
specifies configuring the GPIO00 Alternate 1 Signal (PreAddr07) to use
the alternate three-state control (first option), and specifies
configuring the GPIO32 Alternate 1 Signal (USB2OM0) with the output
enabled in the GPIOx_TCR register (second option).
Currently, gpio_set_chip_configuration() configures all alternate signal
outputs to use the first option. This patch allow the second option to
be selected by setting the "out_val" element in the table entry to
"GPIO_OUT_1". The first option is used when the "out_val" element is
set to "GPIO_OUT_0". Because "out_val" is not currently used when an
alternate signal is selected, and because all current GPIO tables set
"out_val" to "GPIO_OUT_0" for all alternate signals, this patch should
not change any existing configurations.
Signed-off-by: Larry Johnson <lrj@acm.org>
In an attmemt to clean up the 4xx start.S file, I removed the enabling
of the internal 405EP PCI arbiter. This is needed for multiple other
405EP platforms, like most of the esd 405EP. Now the internal PCI
arbiter is enabled again per default as it has been before.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
This patch adds SPD DDR2 support for the 440EPx ("Denali") SDRAM
controller. It should also work on the 440GRx. It is based on the DDR2
SPD code for the 440EP/440EPx, but makes no provision for DDR1 support.
This code has been tested on prototype Korat boards with three Kingston
DIMMS: 512 MiB ECC (one rank), 512 MiB non-ECC (one rank) and 1 GiB ECC
(two ranks). The Korat board has a single DIMM socket, but support has
been provided (though not tested) for boards with two DIMM sockets.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch creates a non-board-specific file for performing the SDRAM
data-eye search. It also adds ECC error checking to the test of valid
data on readback when ECC is enabled.
Signed-off-by: Larry Johnson <lrj@acm.org>
This patch adds a new switch: "CONFIG_PHY_DYNAMIC_ANEG". When this symbol
is defined, the PHY will advertise it's capabilities for autonegotiation
based on the capabilities shown in the PHY's status registers, including
1000BASE-X. When "CONFIG_PHY_DYNAMIC_ANEG" is not defined, the PHY will
advertise hard-coded capabilities, as before.
Signed-off-by: Larry Johnson <lrj@acm.org>
Now the cpu node setup ("timebase-frequency" and "clock-frequency") is
without using the absolute path to the cpu node. This makes it possible
to use this U-Boot version with both versions of cpu-node naming
"cpu@0" and the former "PowerPC,440EPx@0".
Signed-off-by: Stefan Roese <sr@denx.de>
ppc4xx clear_bss() fails if BSS segment size is not
divisible by 4 without remainder. This patch provides
fix for this problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
flush + invalidate_dcache_range() expect the start and stop+1 address.
So the stop address is the first address behind (!) the range.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
By using aliases in the dts file, the ethernet node fixup is
much easier with the recently added functions.
Please note that the dts file needs the aliases for this to work.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch update the 4xx fdt support. It enabled fdt booting
on the AMCC Kilauea and Sequoia for now. More can follow later
quite easily.
Signed-off-by: Stefan Roese <sr@denx.de>
Till now the UTL registers on 405EX were not initialized but left with
their default values. This patch new initializes some of the UTL
registers on 405EX.
Signed-off-by: Stefan Roese <sr@denx.de>
- Rename CFG_440_GPIO_TABLE to CFG_4xx_GPIO_TABLE
- Cleanup of the 4xx GPIO functions
- Move some GPIO defines from the cpu headers ppc405.h/ppc440.h into gpio.h
Signed-off-by: Stefan Roese <sr@denx.de>
This patch disables the 44x d-cache on 'usb start' and
reenables it on 'usb stop'. This should be seen as a
temporary fix until the generic usb-ohci driver can
life with d-cache enabled.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes some redundant code and decrements the end
address of cache flush and invalidate by 1.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Most 4xx PPC capable of using an I2C bootrom for bootstrap setting
already print a line with the information which I2C bootrom is
used for bootstrap configuration. So we don't need this extra line
with "I2C boot EEPROM en-/dis-abled".
This patch also has a little code cleanup integrated.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds the CONFIG_4xx_DCACHE options to some SDRAM init files
and to the Sequoia TLB init code. Now the cache can be enabled on 44x
boards by defining CONFIG_4xx_DCACHE in the board config file. This
option will disappear, when more boards use is successfully and no
more known problems exist.
This is tested successfully on Sequoia and Katmai. The only problem that
needs to be fixed is, that USB is not working on Sequoia right now, since
it will need some cache handling code too, similar to the 4xx EMAC driver.
Signed-off-by: Stefan Roese <sr@denx.de>
I lately noticed, that newer 4xx board with GBit support sometimes don't
finish link autonegotiation in 4 seconds. Changing this timeout to 5
seconds seems fine here.
Signed-off-by: Stefan Roese <sr@denx.de>
We now use a value in the gd (global data) structure for the UART input
frequency, since the PPC4xx_SYS_INFO struct is always rewritten completely
in get_sys_info().
Signed-off-by: Stefan Roese <sr@denx.de>
The Haleakala is nearly identical with the Kilauea eval board. The only
difference is that the 405EXr only supports one EMAC and one PCIe
interface. This patch adds support for the Haleakala board by using
the identical image for Kilauea and Haleakala. The distinction is done
by comparing the PVR.
Signed-off-by: Stefan Roese <sr@denx.de>
Change 4xx_uart.c:
- Use in_8/out_8 macros instead of in8/out8
- No need for UART_BASE marco anymore, now really handled via function
parameter
- serial_init_common() introduced
- Further coding style cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
This patch starts the rework of the PPC4xx serial driver. First we split
the file into two seperate files, one 4xx_uart.c with the 405/440 UART
handling code and the other one iop480_uart.c with the UART code for the
PLX-Tech IOP480 PPC (PPC403 based).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch moves some common 4xx macros and the PPC405_SYS_INFO/
PPC440_SYS_INFO structure into the common ppc4xx.h header.
Lot's of other macros are good candidates to be consolidated this way
in the future.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds endpoint support for the AMCC Kilauea eval board. It can
be tested by connecting a reworked PCIe cable (only 1x lane singles
connected) to another root-complex.
In this test setup, a 64MB inbound window is configured at BAR0 which maps
to 0 on the PLB side. So accessing this BAR0 from the root-complex will
access the first 64MB of the SDRAM on the PPC side.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for dynamic configuration of PCIe ports for the
AMCC PPC4xx boards equipped with PCIe interfaces. These are the PPC440SPe
boards Yucca & Katmai and the 405EX board Kilauea.
This dynamic configuration is done via the "pcie_mode" environement
variable. This variable can be set to "EP" or "RP" for endpoint or
rootpoint mode. Multiple values can be joined via the ":" delimiter.
Here an example:
pcie_mode=RP:EP:EP
This way, PCIe port 0 will be configured as rootpoint, PCIe port 1 and 2
as endpoint.
Per default Yucca will be configured as:
pcie_mode=RP:EP:EP
Per default Katmai will be configured as:
pcie_mode=RP:RP:REP
Per default Kilauea will be configured as:
pcie_mode=RP:RP
Signed-off-by: Tirumala R Marri <tmarri@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
128MB seems to be the smallest possible value for the memory size
for on PCIe port. With this change now the BAR's of the PCIe cards
are accessible under U-Boot.
One big note: This only works for PCIe port 0 & 1. For port 2 this
currently doesn't work, since the base address is now 0xc0000000
(0xb0000000 + 2 * 0x08000000), and this is already occupied by
CFG_PCIE0_CFGBASE. But solving this issue for port 2 would mean
to change the base addresses completely and this change would have
too much impact right now.
This patch adds debug output to the 4xx pcie driver too.
Signed-off-by: Stefan Roese <sr@denx.de>
These files were introduced with the IBM 405GP but are currently used on all
4xx PPC platforms. So the name doesn't match the content anymore. This patch
renames the files to 4xx_pci.c/h.
Signed-off-by: Stefan Roese <sr@denx.de>
(3) This patch introduces macros like SDRN_PESDR_DLPSET(port) to access
the SDR registers of the PCIe ports. This makes the overall design
clearer, since it removed a lot of switch statements which are not
needed anymore.
Also, the functions ppc4xx_init_pcie_rootport() and
ppc4xx_init_pcie_entport() are merged into a single function
ppc4xx_init_pcie_port(), since most of the code was duplicated.
This makes maintainance and porting to other 4xx platforms
easier.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch is the first patch of a series to make the 440SPe PCIe code
usable on different 4xx PPC platforms. In preperation for the new 405EX
which is also equipped with PCIe interfaces.
(2) This patch renames the functions from 440spe_ to 4xx_ with a
little additional cleanup
Signed-off-by: Stefan Roese <sr@denx.de>
