Add the basic a72 basic dts for j7200. Following nodes were supported:
- UART
- MMC SD
- I2C
- TISCI communication
- LPDDR with 1600MTs configuration.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
MikroTik CRS328-4C-20S-4S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS326-24G-2S board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
This commit includes two board variants, namely the factory
default one and a Bit variant. The Bit board variant has a
bigger Macronix flash.
Add basic U-Boot, UART and SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
MikroTik CRS305-1G-4S Bit board has a switch chip with an integrated
Marvell Prestera 98DX3236 CPU.
The Bit board variant is added, which has a bigger Macronix flash.
Add basic U-Boot, UART and Winbond SPI flash support.
Signed-off-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Jakov Petrina <jakov.petrina@sartura.hr>
Reviewed-by: Stefan Roese <sr@denx.de>
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCXykjtQ8cc2JhYmljQGRl
bnguZGUACgkQ9PVl5Jpo76a1WQCcD+objdS+90mDdT0yTpW3jHS4YiwAn2V2rTTo
4hKj5yxRg3cvb/pBAmbQ
=TyRs
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20200804' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
For 2020.10
-----------
- fixes for Toradex board
- fix warnings from previous PR
- HAB: reset instead of panic after failure
- new board: MYiR Tech MYS-6ULX
- mx6cuboxi: use OF_PLATDATA
- further changes for DM
Travis: https://travis-ci.org/github/sbabic/u-boot-imx/builds/714513163
MYS-6ULX is single board computer (SBC) comes with eMMC or NAND based
on imx6ULL SoC from NXP and provision for expansion board. This
commit adds support only for SBC with NAND.
CPU: Freescale i.MX6ULL rev1.1 528 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 45C
Reset cause: WDOG
Model: MYiR i.MX6ULL MYS-6ULX Single Board Computer with NAND
Board: MYiR MYS-6ULX 6ULL Single Board Computer
DRAM: 256 MiB
NAND: 256 MiB
MMC: FSL_SDHC: 0
In: serial@2020000
Out: serial@2020000
Err: serial@2020000
Net: FEC0
Working:
- Eth0
- MMC/SD
- NAND
- UART 1
- USB host
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
- fix SPL boot issue due to early dbgmcu_init() call
- fix SPL boot issue due to dcache memory region configuration
- add support of CONFIG_ENV_IS_IN_MMC
- add specific SD/eMMC partition for U-Boot enviromnent
- enable env in SPL
- use "env info -q" to remove log during boot
- remove env location override for dh_stm32mp1
- update management of misc_read
- check result of find_mmc_device in stm32prog
- use regulator_set_enable_if_allowed for disabling vdd supply in usbphyc
- enable CMD_ADTIMG flag to handle Android images
- device tree alignment with Linux Kernel v5.8-rc1
- remove hnp-srp-disable for usbotg on dk1
- add reset support to uart nodes on stm32mp15x
- use correct weak function name spl_board_prepare_for_linux
- use cd-gpios for ST and DHSOM boards
- add seeed studio odyssey-stm32mp157c board support
- move ethernet PHY into SoM DT
- add DHSOM based DRC02 board support
Add support for Broadcom Northstar 3 SoC.
NS3 is a octo-core 64-bit ARMv8 Cortex-A72 processors
targeting a broad range of networking applications.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Changes in relation to FriendlyARM's U-Boot nanopi2-v2016.01:
- SPL not supported yet --> no spl-dir in arch/arm/cpu/armv7/s5p4418/.
Appropriate line in Makefile removed.
- cpu.c: '#include <cpu_func.h>' added.
- arch/arm/cpu/armv7/s5p4418/u-boot.lds removed, is not required
anylonger.
- "obj-$(CONFIG_ARCH_NEXELL) += s5p-common/" added to
arch/arm/cpu/armv7/Makefile since s5p-common/pwm.c is used instead
of drivers/pwm/pwm-nexell.c.
- s5p4418.dtsi: '#include "../../../include/generated/autoconf.h"'
removed, is not necessary, error at out-of-tree building.
'#ifdef CONFIG_CPU_NXP4330'-blocks (2x) removed. Some minor changes
regarding mmc. 'u-boot,dm-pre-reloc' added to dp0 because of added
DM_VIDEO support.
- board/s5p4418/ renamed to board/friendlyarm/
- All s5p4418-boards except nanopi2 removed because there is no
possibility to test the other boards.
- Kconfig: Changes to have a structure like mach-bcm283x (RaspberryPi),
e.g. "config ..." entries moved from/to other Kconfig.
- "CONFIG_" removed from several s5p4418/nanopi2 specific defines
because the appropriate values do not need to be configurable.
- nanopi2/board.c: All getenv(), getenv_ulong(), setenv() and saveenv()
renamed to env_get(), env_get_ulong(), env_set() and env_save(),
respectively. MACH_TYPE_S5P4418 is not defined anymore, therefore
appropriate code removed (not necessary for DT-kernels).
- nanopi2/onewire.c: All crc8() renamed to crc8_ow() because crc8() is
already defined in lib/crc8.c (with different parameters).
- dts: "nexell,s5pxx18-i2c" used instead of "i2c-gpio", i2c0 and
i2c1 added. gmac-, ehci- and dwc2otg-entries removed because the
appropriate functionality is not supported yet. New mmc-property
"mmcboost" added.
s5p4418-pinctrl.dtsi: gmac-entries removed, mmc- and i2c-entries
added.
- '#ifdef CONFIG...' changed to 'if (IS_ENABLED(CONFIG...))' where
possible (and similar).
Signed-off-by: Stefan Bosch <stefan_b@posteo.net>
Add DT for DH DRC02 unit, which is a universal controller device.
The system has two ethernet ports, two CANs, RS485 and RS232, USB,
capacitive buttons and an OLED display.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This commit adds device tree files supporting
SBC from Seeed Studio based on STM32MP157C.
This works with generic stm32mp1 config.
Right now only booting from SD card is supported.
Signed-off-by: Marcin Sloniewski <marcin.sloniewski@gmail.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The Beacon EmbeddedWorks kit is based on the R8A774A1 SoC also
known as the RZ/G2M.
The kit consists of a SOM + Baseboard and supports microSD,
eMMC, Ethernet, a couple celular radios, two CAN interfaces,
Bluetooth and WiFi.
Signed-off-by: Adam Ford <aford173@gmail.com>
Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enabled
GPIO pin change compared to 4B, 4C.
So, add or enable difference nodes/properties in 4C dts
by including common dtsi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock PI 4 has 3 variants of hardware platforms called
RockPI 4A, 4B, and 4C.
- Rock PI 4A has no Wif/BT.
- Rock PI 4B has AP6256 Wifi/BT, PoE.
- Rock PI 4C has AP6256 Wifi/BT, PoE, miniDP, USB Host enable
GPIO pin change compared to 4B, 4C
So move common nodes, properties into dtsi file and include
on respective variant dts files.
Use 4B dts into default rock-pi-4 defconfig until we find any
solution for dynamic detection of these variants.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Get the devicetree from mainline Linux and include it for U-Boot uses.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Convert pcm058 support to use device trees and the driver model.
Add rudimentary boot scripts to the environment, expand README.
Signed-off-by: Niel Fourie <lusus@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This imports the changes and the new Odroid-C4 board from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Rock Pi N8 is a Rockchip RK3288 based SBC, which has
- VMARC RK3288 SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3288 SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N8 SBC.
So, add initial support for Rock Pi N8 by including rk3288,
rk3288 vamrc-som and raxda dalang carrier board dtsi files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rock Pi N10 is a Rockchip RK3399Pro based SBC, which has
- VMARC RK3399Pro SOM (as per SMARC standard) from Vamrs.
- Compatible carrier board from Radxa.
VAMRC RK3399Pro SOM need to mount on top of radxa dalang
carrier board for making Rock Pi N10 SBC.
So, add initial support for Rock Pi N10 by including rk3399,
rk3399pro vamrc-som and raxda dalang carrier board dtsi files.
rk3399pro-rock-pi-n10.dts was synced from linux-next v5.7-rc1.
Tested
- ROCK PI N10 Model B
- ROCK PI N10 Model C
- Boot from SD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
XDP - Xilinx Drone Platform is a board for drones or other UAV.
Pinmux the SD card by default, and if the SD card detect line is high
(inactive) then pinmux the SD1 interface to EMIO instead. SD is placed on
extension card and shares connection with on board wife. That means that
when SD card is present in the board wifi can't be used.
There seems to be an issue with DDR access from PL at 2400MT/s, after
updating the PMU and ATF firmware this is causing extremely slow DDR
access. Reducing the DDR speed from 2400 to 2133 appears to solve that
issue, even though the hardware has proven to be 2400 capable.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
So far the puma dts files only just included the main puma dtsi without
handling the actual baseboard and rk3399-puma.dtsi was very much
detached from the variant in the mainline Linux kernel.
Recent changes resulted in a strange situation with nonworking puma boards.
Commit ab800e5a6f ("arm: dts: rockchip: puma: move U-Boot specific bits to u-boot.dtsi")
moved the sdram include from rk3399-puma-ddrX.dts to new files
rk3399-puma-ddrx-u-boot.dtsi which were never included anywhere though.
Commit 167efc2c7a ("arm64: dts: rk3399: Sync v5.7-rc1 from Linux")
replaced the rk3399-puma.dtsi nearly completely, but in the kernel
it definitly depends on a baseboard dts to actually enable peripherals
like sd-slot, uarts, etc.
So to untagle this and bring the whole thing more in line with mainline
Linux, bring the rk3399-puma-haikou.dts over as well, drop the separate
DDR-option devicetrees and instead replace them with a puma Kconfig option
to select and include the needed DDR variant.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The ROCK-PI-E is a credit card size SBC based on Rockchip RK3328
Quad-Core ARM Cortex A53.
Net - Dual ethernet port, 1 X Gbe, 1 X 100M
USB - USB 3.0
DC - USB-Type C, 5V 2A
Storage - TF card, eMMC
Just build idbloader.img and u-boot.itb for Rockpi E board and
follow the blow steps to replace the relevant partition.
dd if=idbloader.img of=/dev/sdcard seek=64 conv=notrunc
dd if=u-boot.itb of=/dev/sdcard seek=16384 conv=notrunc
Signed-off-by: Banglang Huang <banglang.huang@foxmail.com>
Sync initial support for Pinebook Pro device tree from Linux 5.7-rc1.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reserve 4 kiB of space in R-Car Gen3 DTs when those DTs are compiled
to permit patching in OpTee-OS /firmware node, /reserved-memory node
and possibly also additional /memory@ nodes.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used.
The fsl-ls2080a-qds DTS will be used by default if there isn't a DTS
file specifically made for the current SERDES protocol.
This patch adds the necessary DPMAC nodes (DPMAC 1-8) for
protocol 42 (0x2A) on SD#1.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add support for selecting the appropriate DTS file depending on the
SERDES protocol used. The fsl-ls2088a-qds DTS will be used by default if
there isn't a DTS file specifically made for the current SERDES
protocol.
This patch adds support for the on-board ports (DPMAC 1,2 and 4,5) found
on the SERDES protocols 21(0x15) and 29(0x1d) for SD#1.
On the LS1088AQDS board EMDIO1 is used with two onboard RGMII PHYs
(Realtek RTL8211FD-CG), as well as 2 input/output connectors for
mezzanine cards. Configuration signals from the Qixis FPGA control the
routing of the external MDIOs.
Register 0x54 of the Qixis FPGA controls the routing of the EMDIO1 one
of the 2 IO slots. As a consequence, a new node is added to
describe register 0x54 as a MDIO mux controlled with child nodes
describing all the IO slots as MDIO buses.
Also, in case CONFIG_DM_ETH and CONFIG_MULTI_DTB_FIT are enabled
implement the board_fit_config_name_match() function in order to choose
the appropriate DTS.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add device trees describing possible uses of mezzanine cards depending
on the SERDES protocol employed.
This patch adds DPAA2 networking support for the following protocols on
each SERDES block:
* SD #1: 3, 7, 19, 20
* SD #2: 11
Each SERDES block has a different device tree file per protocol
supported, where the IO SLOTs used are enabled and PHYs located on the
mezzanine cards are described. Also, dpmac nodes are edited and their
associated phy-connection-type and phy-handle are added.
Top DTS files are also added for each combination of protocol on the 3
SERDES blocks.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Razvan Ionut Cirjan <razvanionut.cirjan@nxp.com>
[Rebased]
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Beacon EmbeddedWorks, formerly known as Logic PD, is releasing
a devkit based on the i.MX8M Mini SoC consisting of baseboard +
SOM.
It supports eMMC on the SOM, microSD on the baseboard, various
GPIO, the PINCTRL, and UART.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add initial support for Technexion Pico-iMX8MQ SoM on PicoPI carrier
board. Currently working is ethernet, serial, eMMC. DT is imported
from Linux 5.4.28 ("462afcd6e7ea") .
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
- dts clean up to use -u-boot for px30, rk3399 boards
- dts sycn from upstream kernel for rk3328, rk3399
- add rockchip rng driver
- new board support: rk3328-roc-cc, rk3399-roc-pc,Nanopi M4 2GB
Add initial support for Google's Coral Dev Board based on i.MX8MQ.
https://coral.ai/products/dev-board
The Phanbell naming has been used here to match the naming convention
used in Google's U-Boot source tree:
https://coral.googlesource.com/uboot-imx/
Co-developed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Tested-by: Marco Franchi <marcofrk@gmail.com>
commit b2f5da9dd0 ("rockchip: rk3399: Add Nanopi M4 board support") added
support for Nanopi M4 board with Dual-Channel 4GB LPDDR3-1866 RAM.
This patch adds another variant of NanoPi M4 board with Dual-Channel
2GB DDR3-1866 RAM.
Signed-off-by: Deepak Das <deepakdas.linux@gmail.com>
The ROC-RK3328-CC from Firefly and Libre Computer Project is a credit
card size development board based on the Rockchip RK3328 SoC, with:
- 1/2/4 GB DDR4 DRAM
- eMMC connector for optional module
- micro SD card slot
- 1 x USB 3.0 host port
- 2 x USB 2.0 host port
- 1 x USB 2.0 OTG port
- HDMI video output
- TRRS connector with audio and composite video output
- gigabit Ethernet
- consumer IR receiver
- debug UART pins
The ROC-RK3328-CC has the enable pin of the SD card power switch tied
to GPIO_0_D6. This pin also has the function SDMMC0_PWREN, which is
muxed by default. SDMMC0_PWREN is an active high signal controlled by
the MMC controller, however the switch enable is active low, and
pulled low (enabled) by default to make things work on boot.
As such, we need to mux away from SDMMC0_PWREN and use GPIO to enable
power to the card. The default GPIO state for the pin is pull-down and
input, which doesn't require extra configuration when paired with the
external pull-down and active low switch.
Deal with this by enabling regulator support in SPL, and setting
"u-boot,dm-spl" for the regulator and other device nodes needed for
muxing the pin.
The device tree file is synced from the Linux kernel next-20200324.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
Rename fsl-ls1028a-qds.dts to fsl-ls1028a-qds.dtsi so that
it can be used as common device tree for lpuart and duart.
Add lpuart device tree and duart device tree respectively
for qds which are used with duart and lpuart console.
Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Synchronize R-Car Gen3 device trees with Linux 5.6.2,
commit 9fbe5c87eaa9b72db08425c52c373eb5f6537a0a .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds .dtsi file(sync with Linux 5.5-rc6 with hash "b3a987b0264d")
and required binding for S700 SoC that is a 64-bit Quad-core ARM
Cortex-A53 cores.
It also provisions dts file to be built based on selected
platform(CONFIG_MACH_S900/S700).
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
