Pull DRAM layout configuration code into rcar-common.c instead of
having it in multiple copies across board files. This poses no
change for Salvator-X/XS, ULCB and Ebisu boards, however it adds
a bit of extra code for Draak and Eagle boards, which now gain
the capability of being passed in the DRAM layout by the ATF.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Eugeniu Rosca <roscaeugeniu@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Build an SPL which can be started via SCIF download mode on R-Car Gen3
and allows loading and executing U-Boot uImage with the next stage code.
This is also useful for starting e.g. ATF BL2, which inits the hardware
and returns to the U-Boot SPL, which can then load e.g. U-Boot proper.
The H3, M3-W, M3-N SoCs have plenty of SRAM for storing the U-Boot SPL
while the payload, e.g. ATF BL2, executes, so there is no problem here.
However, E3 and D3 have much less SRAM, hence the loader uses a trick
where it copies itself beyond the area used by BL2 and executes from
there. That area is 32kiB large and not enough to hold U-Boot SPL, BSS,
stack and malloc area, so the later two are placed at +0x4000 offset
from start of SRAM, another area not used by ATF BL2. To make things
even more complicated, the SCIF loader cannot load to the upper 32kiB
of the SRAM directly, hence the copying approach.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Add board code and DTs for Renesas RZ/A1 SoC-based GR-Peach,
which is a cheap development platform with RZ/A1H SoC. The
DTs are imported from Linux 5.0.11, commit d5a2675b207d .
Currently supported are UART, ethernet and RPC SPI. The board
can be booted from RPC SPI by writing the u-boot.bin binary
to the beginning of the SPI NOR, e.g. using the "sf" command.
The board can also be booted via JTAG by setting text base to
0x20020000, loading u-boot.bin there via JTAG and executing it
from that address.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Last change to this board was done in 2016, it uses non-DM USB
with no prospects of ever being converted to DM USB, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Update the README to use the correct defconfig.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
The ATF can pass additional information via the first four registers,
x0...x3. The R-Car Gen3 with mainline ATF, register x1 contains pointer
to a device tree with platform information. Parse this device tree and
extract DRAM size information from it. This is useful on systems where
the DRAM size can vary between configurations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
v2018.01 commit e23eb942ad ("ARM: rmobile: Stop using
rcar-common/common.c on Gen3") removed
board/renesas/rcar-common/common.c from the build chain with the
reasoning that calling arch_preboot_os() is no longer needed.
However, it left the arch_preboot_os() in place. Get rid of it.
This is done in preparation of resurrecting rcar-common/common.c.
NOTE: The three removed header includes (io.h, sys_proto.h, rcar-mstp.h)
are in direct relationship with the dropped arch_preboot_os() hook. The
other headers (common.h, rmobile.h) are going to be needed by pretty
much anything that is going to appear in the rcar common code. So, keep
the two in place.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Add defconfig and board specific adjustments for the R8A77965 M3N ULCB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The I2C bus number to access the PMIC is I2C 7, fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PHY LED mode register mask should be 0xc000 , not 0xc0000.
Correct the mask to operate on the right bits.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The R8A7794_ETHERNET_B config option is unused and based on the
description, this is a setting which should be fully done on a
DT level instead. Remove this config option.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Bundle DTBs for R8A7795, R8A7796 ULCB variants into single U-Boot
build and let U-Boot choose between them based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Bundle DTBs for R8A7795, R8A7796, R8A77965 Salvator-X variants
into the single U-Boot build and let U-Boot choose between them
based on the CPU model.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop unused MSTP macros from Gen3 boards. These are no longer needed
as the boards are using clock framework to manipulate clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When referring to the MSTPSR register, it contains the clock
status of SYS, RT, SECURE, and controlling SMSTPCR using this
value has the problem of being affected by the RT and SECURE
status.This patch changes the reference register to SMSTPCR.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
GSX clock force supply code is unnecessary at U-Boot,
because GSX clock control is supported at the kernel driver.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
This code is unnecessary, because these registers are set by the
initial program loader (IPL).
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Drop the macro as it is defined in sh7723.h already.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Fix the CPGWPR/CPGWPCR register address on V3M Eagle to unlock
access to the CPG clock control registers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The V2H Blanche port was broken since some time. This patch updates
the V2H Blanche port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Pull the symbol from the boards and zap struct rmobile_sysinfo as they
are rather useless. The entire purpose of that whole machinery was to
print board name in the CONFIG_ARCH_RMOBILE_BOARD_STRING. Do that in a
far simpler and more contained manner.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rename CONFIG_RMOBILE_BOARD_STRING to CONFIG_ARCH_RMOBILE_BOARD_STRING
to make things consistent, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The E2 Alt port was broken since some time. This patch updates
the E2 Alt port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The M2-N Gose port was broken since some time. This patch updates
the M2-N Gose port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Lager port was broken since some time. This patch updates
the H2 Lager port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The E2 Silk port was broken since some time. This patch updates
the E2 Silk port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: The port is missing support for I2C1 for DA9063 reset, since the
I2C driver needs to be converted to DM and DT probing. That's not
an issue for this patch though, since the reset was broken on Silk
since forever.
The M2 Koelsch port was broken since some time. This patch updates
the M2 Koelsch port to use modern frameworks, DM, DT probing, SPL
for the preloading and puts it on par with the M2 Porter board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot is started via JTAG, ignore the installed environment
as it may interfere with the recovery of the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
When U-Boot is started via JTAG, ignore the installed environment
as it may interfere with the recovery of the board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is currently no use for building the SPL anymore, since the
SPI loader can easily be replaced by TPL and TPL does load U-Boot
directly. Upgrade TPL to SPL and replace what used to be SPL with
it. This way we build the U-Boot sources only twice, not thrice.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The H2 Stout port was broken since some time. This patch updates
the H2 Stout port to use modern frameworks, DM, DT probing, SPL
and TPL for the preloading and puts it on par with the M2 Porter
board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add JTAG recovery support into the M2 Porter TPL. This allows the
TPL to be loaded over JTAG, initialize the system, wait for the
JTAG debugger to load U-Boot image into RAM and then resume and
start U-Boot from RAM.
The procedure is as follows:
1) Load u-boot-tpl.bin to 0xe6300000
2) Write magic number 0x1337c0de to 0xe6300020
TPL checks for this particular magic and starts JTAG recovery
if this number is present. This is not present by default.
3) Start U-Boot TPL from 0xe6300000
4) Wait for a message from TPL on UART indicating JTAG boot:
"JTAG boot detected!"
5) Halt the system in JTAG debugger
6) Load U-Boot image (u-boot.img) to 0x4fffffc0
7) Write magic number 0xb33fc0de to 0xe6300024
TPL checks for this particular magic to verify that the U-Boot
image was loaded into DRAM by the JTAG debugger.
8) Resume the system in JTAG debugger
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add and enable TPL on M2 Porter. The TPL must fit into 16 kiB due
to the Gen2 BootROM restriction. The TPL is running from MERAM and
is capable of performing the initial initialization of PFC, Clock,
GPIO, LBSC, DBSC and QSPI NOR. DBSC is responsible for bringing up
the DDR DRAM access. The TPL is capable of loading the next stage,
U-Boot, from either SPI NOR or UART as a fallback. If either does
provide a valid U-Boot uImage, the system stops, which allows the
operator to load U-Boot ie. via JTAG and start it manually.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Pull the SPL code from porter.c into a separate file in
preparation for the addition of system initialization code.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In order that we can use eth_env_* even when CONFIG_NET isn't set, move
these functions to environment code from net code.
This fixes failures such as:
board/ti/am335x/built-in.o: In function `board_late_init':
board/ti/am335x/board.c:752: undefined reference to `eth_env_set_enetaddr'
u-boot/board/ti/am335x/board.c:766: undefined reference to `eth_env_set_enetaddr'
which caters for use cases such as:
commit f411b5cca4 ("board: am335x: Always set eth/eth1addr environment
variable")
when Ethernet is required in Linux, but not U-Boot.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77995 D3 Draak.
The DT file is from Linux 4.15-rc1 , commit
b35334447513c14a4dd55a67c269a743d4a4824b .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add bits to support yet another board, the R8A77970 V3M Eagle.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rework the ULCB CPLD driver and make it into a sysreset driver,
since that is what the ULCB CPLD driver is mostly for.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the ad-hoc DRAM configuration with macros and just decode
the DRAM configuration from device tree instead. This makes it
far cleaner and easier.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since checkboard() is gone, rmobile_sysinfo is also pointless on Gen3.
Furthermore, nuke ad-hoc CONFIG_RCAR_BOARD_STRING which is also dead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We can now use rmobile_get_cpu_type() to check the CPU ID rather
than using a macro, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Since the Gen3 clock driver now has a .remove callback, it is no
longer necessary to shut the clock down before booting Linux in the
arch_preboot_os hook. Stop using it and while doing so, remove all
the ad-hoc config options which this hook used.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ULCB CPLD support was not updated during the PFC table rework,
fix up the GPIO numbers until the CPLD support is rewritten to a
proper DM capable and DT probing driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
At long last, nuke all this ad-hoc setup in board files in favor of
letting PFC pinmux and GPIO drivers do the same job, but based on DT
description of the hardware rather than this board-file ugliness.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Enable the PFC pinmux and GPIO drivers and disable the SH GPIO combo
driver. This allows the drivers to obtain pinmux and GPIO configuration
from DT rather than hard-coding it in board files.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The configuration is now fully performed by the SCIF and clk drivers,
so remove it from the board file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The configuration is now fully performed by the AVB and clk drivers,
so remove it from the board file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The configuration is now fully performed by the SD and clk drivers,
so remove it from the board file.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In order to use ehci-generic driver, move the configuration of HSUSB
block into the board file. This configuration should not have been in
the Gen3 EHCI USB driver in the first place, so move it to the board
file until there is a proper infrastructure and driver for the HSUSB
block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
In order to use ehci-generic driver, move the configuration of HSUSB
block into the board file. This configuration should not have been in
the Gen3 EHCI USB driver in the first place, so move it to the board
file until there is a proper infrastructure and driver for the HSUSB
block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
On RCar M3 and on RCar H3 newer than and not including ES1.0, the SD clock
must be divided by 4 rather than 2 because a hardware workaround present
only in the H3 ES1.0 has been removed from these chips. U-Boot currently
only supports M3 and H3 ES 2.0 and newer, so configure the SD pre-divider
to 4 to prevent SD instability.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The board_mmc_init() is no longer invoked when DM is used, so move
all the pinmux config into board_init() instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The configuration option name is the later, so replace usage of
CONFIG_RAVB in board files with CONFIG_RENESAS_RAVB , otherwise
the RAVB pinmux is not set and ethernet does not work.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the SH SDHI bit from the board since SD now probes from DT instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the SH SDHI bit from the board since SD now probes from DT instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the Serial SH bit from the board since UART now probes from DT instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the Serial SH bit from the board since UART now probes from DT instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the RAVB bit from the board since RAVB now probes from DT instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Drop the RAVB bit from the board since RAVB now probes from DT instead.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Add initial support for the R8A7795 and R8A7796 based ULCB board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add minor ifdeffery and default board config for the Salvator-XS board
with R8A7796 M3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rename the salvator-x_defconfig to r8a7795_salvator-x_defconfig in
preparation for the r8a7796 support on salvator-x board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Instead of counting only the DRAM in the first slot, count
all the DRAM in all slots and report it accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the EHCI USB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for rebooting the board using the ROHM BD9571MWV I2C PMIC,
but keep the CPU reboot option as a fallback.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the AVB ethernet on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the SD card slots on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The UART uses internal SCIF clock except on R8A7795 H3 WS1.0 .
Use the internal clock and ignore the early version of the chip.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The macro is used twice in the salvator-x board file, drop one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We repeated partial moves for CONFIG_SYS_NO_FLASH, but this is
not completed. Finish this work by the tool.
During this move, let's rename it to CONFIG_MTD_NOR_FLASH.
Actually, we have more instances of "#ifndef CONFIG_SYS_NO_FLASH"
than those of "#ifdef CONFIG_SYS_NO_FLASH". Flipping the logic will
make the code more readable. Besides, negative meaning symbols do
not fit in obj-$(CONFIG_...) style Makefiles.
This commit was created as follows:
[1] Edit "default n" to "default y" in the config entry in
common/Kconfig.
[2] Run "tools/moveconfig.py -y -r HEAD SYS_NO_FLASH"
[3] Rename the instances in defconfigs by the following:
find . -path './configs/*_defconfig' | xargs sed -i \
-e '/CONFIG_SYS_NO_FLASH=y/d' \
-e 's/# CONFIG_SYS_NO_FLASH is not set/CONFIG_MTD_NOR_FLASH=y/'
[4] Change the conditionals by the following:
find . -name '*.[ch]' | xargs sed -i \
-e 's/ifndef CONFIG_SYS_NO_FLASH/ifdef CONFIG_MTD_NOR_FLASH/' \
-e 's/ifdef CONFIG_SYS_NO_FLASH/ifndef CONFIG_MTD_NOR_FLASH/' \
-e 's/!defined(CONFIG_SYS_NO_FLASH)/defined(CONFIG_MTD_NOR_FLASH)/' \
-e 's/defined(CONFIG_SYS_NO_FLASH)/!defined(CONFIG_MTD_NOR_FLASH)/'
[5] Modify the following manually
- Rename the rest of instances
- Remove the description from README
- Create the new Kconfig entry in drivers/mtd/Kconfig
- Remove the old Kconfig entry from common/Kconfig
- Remove the garbage comments from include/configs/*.h
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Generic board support assumes a different method of specifying
DRAM size on board, also it can be shared among all boards, notably
only sh7763rdp board has a custom legacy dram_init(), however
the difference is only in printing some additional information,
this feature can be removed.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reference lowlevel_init of all supported SH2A/SH3/SH4/SH4A boards
from a shared linker script, the lowlevel_init function will be called
by a relative address.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Three supported SH4/SH4A boards with the bootloader image stored on
SPI flash have own flavour of a linker script, in turn they are equal
among each other. The only difference is that the text from
lowlevel_init.o is placed right after start.o, which makes sense.
Note that .bss section is not marked as NOLOAD, because for about
10 years this is a default option of a GNU linker, either the
attribute is found or not the resulting image file is the same.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
To common use of rcar-gen2-common directory in the R-Car SoCs,
and change from rcar-gen2-common to rcar-common.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
