There some vendor quirks for MTK xHCI 0.96 host controller:
1. It defines some extra SW scheduling parameters for HW
to minimize the scheduling effort for synchronous and
interrupt endpoints. The parameters are put into reserved
DWs of slot context and endpoint context.
2. Its TDS in Normal TRB defines a number of packets that
remains to be transferred for a TD after processing all
Max packets in all previous TRBs.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xhci versions 1.0 and later report the untransferred data remaining in a
TD a bit differently than older hosts.
We used to have separate functions for these, and needed to check host
version before calling the right function.
Now Mediatek host has an additional quirk on how it uses the TD Size
field for remaining data. To prevent yet another function for calculating
remainder we instead want to make one quirk friendly unified function.
Porting from the Linux:
c840d6ce772d("xhci: create one unified function to calculate TRB TD remainder.")
124c39371114("xhci: use boolean to indicate last trb in td remainder calculation")
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a member to save xHCI version, it's used some times.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some atypical users of xhci might need to manually reset their xHCI
controller before starting the HCD setup. Check if a reset controller
device is available to the PCI bus and trigger a reset.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
[mb: squash fix to only build xhci_reset_hw() if CONFIG_DM_BUS]
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
There might be hardware configurations where 64-bit data accesses
to XHCI registers are not supported properly. This patch removes
the readq/writeq so always two 32-bit accesses are used to read/write
64-bit XHCI registers, similarly as it is done in Linux kernel.
This patch fixes operation of the XHCI controller on RPI4 Broadcom
BCM2711 SoC based board, where the VL805 USB XHCI controller is
connected to the PCIe Root Complex, which is attached to the system
through the SCB bridge.
Even though the architecture is 64-bit the PCIe BAR is 32-bit and likely
the 64-bit wide register accesses initiated by the CPU are not properly
translated to a sequence of 32-bit PCIe accesses.
xhci_readq(), for example, always returns same value in upper and lower
32-bits, e.g. 0xabcd1234abcd1234 instead of 0x00000000abcd1234.
Cc: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Add compatible "st,stm32mp1-hsotg" and associated driver data to manage
the usb33d-supply and the ST specific register for VBus sensing.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/usb/gadget/dwc2_udc_otg.c
Reviewed-by: Lukasz Majewski <lukma@denx.de>
All TX fifo size can be different, add tx_fifo_sz_array[]
into dwc2_plat_otg_data to be able to set them.
tx_fifo_sz_array[] is 17 Bytes long and can contains max 16
tx fifo size (synopsys IP supports max 16 IN endpoints).
First entry of tx_fifo_sz_array[] is the number of valid
fifo size the array contains.
In case of tx_fifo_sz_array[] doesn't contains the same
number of element than max hardware endpoint, display
a warning message.
Compatibility with board which doesn't use tx_fifo_sz_array[]
(Rockchip rk322x/rk3128/rv1108/rk3288/rk3036) is kept.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Add a new function to check the session B validity, to be use to check
cable connection.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
The BITMAP related operations can now be moved to ./include/linux/bitmap.h
file to mimic the Linux kernel directory tree.
This change also allows to remove the lin_gadget_compat.h header file
(which is a legacy code only for composite U-boot layer).
It was also possible to remove #includes from several USB gadget drivers.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
The regs_phy field of the platform data structure for dwc2-otg is
today declared an unsigned int, but will eventually be cast into a
void* for a writel operation. This triggers errors on modern GCC
versions.
E.g. we get the following error with GCC 6.3:
drivers/usb/phy/rockchip_usb2_phy.c: In function 'property_enable':
arch/arm/include/asm/io.h:49:29: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
#define __arch_putl(v,a) (*(volatile unsigned int *)(a) = (v))
^
arch/arm/include/asm/io.h:117:48: note: in expansion of macro '__arch_putl'
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^~~~~~~~~~~
drivers/usb/phy/rockchip_usb2_phy.c:61:2: note: in expansion of macro 'writel'
writel(val, pdata->regs_phy + reg->offset);
^~~~~~
This commit changes regs_phy to be a uintptr_t to ensure that it is
large enough to hold any valid pointer (and fix the associated
warning).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Same macros are defined in various places. Collect them into
include/linux/bitops.h like Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When compiling with W=1 the following warning is observed:
board/freescale/mx6sabresd/mx6sabresd.c:601:5: warning: no previous prototype for ‘board_ehci_power’ [-Wmissing-prototypes] int board_ehci_power(int port, int on)
Remove this warning by adding the function prototype into usb/ehci-ci.h file.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
The regs_otg field in uintptr_t of the platform data structure for
dwc2-otg has thus far been an unsigned int, but will eventually be
casted into a void*.
This raises the following error with GCC 6.3 and buildman:
../drivers/usb/gadget/dwc2_udc_otg.c: In function 'dwc2_udc_probe':
../drivers/usb/gadget/dwc2_udc_otg.c:821:8: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
reg = (struct dwc2_usbotg_reg *)pdata->regs_otg;
^
This changes regs_otg to a uintptr_t to ensure that it is large enough
to hold any valid pointer (and fix the associated warning).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Remove Soc specific defines and use generic chasis specific defines
for USB controller base address mapping.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The total FIFO size of some SoCs may be different from the existen, this
patch supports fifo size setting from platform data.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
So far, Rockchip SoCs have two kinds of USB2.0 phy, such as Synopsys and
Innosilicon. This patch applys dwc2 usb driver framework to implement
phy_init() and phy_off() methods for Synopsys phy on Rockchip platform.
Signed-off-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use definitions from ehci.h instead.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Some registers of usb_ehci were marked as reserved.
This may be true for some variants of Chipidea USB core, but they have
meaning on other devices.
The following registers were added:
sbusstatus/sbusmode: AHB-related registers
genconfig*: Auxiluary IP core configuration registers.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
Most of ehci-fsl header describe USB controller
designed by Chipidea and used by various SoC vendors.
This patch renames it to a generic header: ehci-ci.h
Contents of file are not changed (so it contains several
references to freescale SoCs).
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Simon Glass <sjg@chromium.org>
ulpi_read and ulpi_write are used to read/write registers via ULPI bus.
Code generates compilation warnings on 64-bit machines where pointer
is cast to u32.
This patch drops all but last 8 bits of register address.
It is possible, because addresses on ULPI bus are 6- or 8-bit.
It is not possible (according to ULPI 1.1 spec) to have more
than 8-bit addressing.
This patch should not cause regressions as all calls to
ulpi_read/write use either structure pointer (@ address 0) or integer
offsets cast to pointer - addresses requested are way below 8-bit range.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
viewport_addr is address of memory mapped ULPI viewport.
It is used only as argument to readl/writel later
causing compile warnings on 64-bit devices.
This fix changes its type to match pointer size.
Signed-off-by: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
In a number of places we had wordings of the GPL (or LGPL in a few
cases) license text that were split in such a way that it wasn't caught
previously. Convert all of these to the correct SPDX-License-Identifier
tag.
Signed-off-by: Tom Rini <trini@konsulko.com>
The driver is actually for the Designware DWC2 controller.
This patch renames the global s3c_udc.h header to dwc2_udc.h.
The rename is done automatically:
$ sed -i "s/s3c_udc\.h/dwc2_udc.h/g" \
`git grep "s3c_udc\.h" | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the second and final to rename global symbol,
the s3c_udc_probe() function.
The rename is done automatically:
$ sed -i "s/s3c_udc_probe/dwc2_udc_probe/g" \
`git grep s3c_udc_probe | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch is the first to rename global symbol, the struct
s3c_plat_otg_data.
The rename is done automatically:
$ sed -i "s/s3c_plat_otg_data/dwc2_plat_otg_data/g" \
`git grep s3c_plat_otg_data | cut -d : -f 1`
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
Tweak the comments in the driver to reflect this fact.
Signed-off-by: Marek Vasut <marex@denx.de>
The extern statements are useless, remove them. Also remove the
extern ... controller, which is completely useless.
Signed-off-by: Marek Vasut <marex@denx.de>
Most of the functions are local to the s3c_udc driver, remove them
from the s3c_udc.h header to stop those bits from propagating all
over the place. Instead, move all the private stuff into new private
s3c_udc_otg_priv.h header.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_udc to struct dwc2_udc to make
things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
Define USB configs for LS1021XA such as CONFIG_SYS_FSL_USB1_ADDR,
CONFIG_USB_MAX_CONTROLLER_COUNT
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
usb_phy_enable should return status bit, but not phy mode bit, thus
add a new function usb_phy_mode to query the PHY for it's mode and
make usb_phy_enable just return 0 but not 'phy_ctrl & USBPHY_CTRL_OTG_ID'.
Include a new board weak function board_usb_phy_mode. If board code
does not reimplement this function, it just call usb_phy_mode and return
usb_phy_mode's return value. The reason to include such a weak function
is: " SOC OTG core <--connect--> board HOST port, but no pin id for
the board host port, so board can not use usb_phy_mode to return the
phy mode, but define it's own rule."
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye Li <B37916@freescale.com>
[1] arch/arm/include/asm/arch-at91/at91_shdwn.h
The top9000 was the last board to use this header file.
It was removed by commit d58a9451e7 (ppc/arm: zap EMK boards).
[2] board/matrix_vision/common/*
Some Matrix Vision boards were dropped by commit e7a565638a
(powerpc: mpc83xx: remove board support for MERGERBOX and MVBLM7)
and commit af55e35d33
(powerpc: mpc5xxx: remove board support for MVBC_P and MVSMR).
Since then these files have been unused.
[3] include/usb/omap1510_udc.h
The omap5912osk was the last board to use this header file.
It was removed by commit 62d636aa2a
(omap: remove omap5912osk board support).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-By: Wolfgang Denk <wd@denx.de>
resync ubi subsystem with linux:
commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date: Sun Mar 30 20:40:15 2014 -0700
Linux 3.14
A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
